- Linux-stable-mirror - lists.linaro.org

[Linux-stable-mirror] [PATCH 2/5] can: xilinx_can: fix RX loop if RXNEMP is asserted without RXOK

by Anssi Hannula

If the device gets into a state where RXNEMP (RX FIFO not empty) interrupt is asserted without RXOK (new frame received successfully) interrupt being asserted, xcan_rx_poll() will continue to try to clear RXNEMP without actually reading frames from RX FIFO. If the RX FIFO is not empty, the interrupt will not be cleared and napi_schedule() will just be called again. This situation can occur when: (a) xcan_rx() returns without reading RX FIFO due to an error condition. The code tries to clear both RXOK and RXNEMP but RXNEMP will not clear due to a frame still being in the FIFO. The frame will never be read from the FIFO as RXOK is no longer set. (b) A frame is received between xcan_rx_poll() reading interrupt status and clearing RXOK. RXOK will be cleared, but RXNEMP will again remain set as the new message is still in the FIFO. I'm able to trigger case (b) by flooding the bus with frames under load. There does not seem to be any benefit in using both RXNEMP and RXOK in the way the driver does, and the polling example in the reference manual (UG585 v1.10 18.3.7 Read Messages from RxFIFO) also says that either RXOK or RXNEMP can be used for detecting incoming messages. Fix the issue and simplify the RX processing by only using RXNEMP without RXOK. Tested with the integrated CAN on Zynq-7000 SoC. Fixes: b1201e44f50b ("can: xilinx CAN controller support") Signed-off-by: Anssi Hannula <anssi.hannula(a)bitwise.fi> Cc: <stable(a)vger.kernel.org> --- drivers/net/can/xilinx_can.c | 18 +++++------------- 1 file changed, 5 insertions(+), 13 deletions(-) diff --git a/drivers/net/can/xilinx_can.c b/drivers/net/can/xilinx_can.c index 389a960..1bda47a 100644 --- a/drivers/net/can/xilinx_can.c +++ b/drivers/net/can/xilinx_can.c @@ -101,7 +101,7 @@ enum xcan_reg { #define XCAN_INTR_ALL (XCAN_IXR_TXOK_MASK | XCAN_IXR_BSOFF_MASK |\ XCAN_IXR_WKUP_MASK | XCAN_IXR_SLP_MASK | \ XCAN_IXR_RXNEMP_MASK | XCAN_IXR_ERROR_MASK | \ - XCAN_IXR_ARBLST_MASK | XCAN_IXR_RXOK_MASK) + XCAN_IXR_ARBLST_MASK) /* CAN register bit shift - XCAN_<REG>_<BIT>_SHIFT */ #define XCAN_BTR_SJW_SHIFT 7 /* Synchronous jump width */ @@ -708,15 +708,7 @@ static int xcan_rx_poll(struct napi_struct *napi, int quota) isr = priv->read_reg(priv, XCAN_ISR_OFFSET); while ((isr & XCAN_IXR_RXNEMP_MASK) && (work_done < quota)) { - if (isr & XCAN_IXR_RXOK_MASK) { - priv->write_reg(priv, XCAN_ICR_OFFSET, - XCAN_IXR_RXOK_MASK); - work_done += xcan_rx(ndev); - } else { - priv->write_reg(priv, XCAN_ICR_OFFSET, - XCAN_IXR_RXNEMP_MASK); - break; - } + work_done += xcan_rx(ndev); priv->write_reg(priv, XCAN_ICR_OFFSET, XCAN_IXR_RXNEMP_MASK); isr = priv->read_reg(priv, XCAN_ISR_OFFSET); } @@ -727,7 +719,7 @@ static int xcan_rx_poll(struct napi_struct *napi, int quota) if (work_done < quota) { napi_complete_done(napi, work_done); ier = priv->read_reg(priv, XCAN_IER_OFFSET); - ier |= (XCAN_IXR_RXOK_MASK | XCAN_IXR_RXNEMP_MASK); + ier |= XCAN_IXR_RXNEMP_MASK; priv->write_reg(priv, XCAN_IER_OFFSET, ier); } return work_done; @@ -799,9 +791,9 @@ static irqreturn_t xcan_interrupt(int irq, void *dev_id) } /* Check for the type of receive interrupt and Processing it */ - if (isr & (XCAN_IXR_RXNEMP_MASK | XCAN_IXR_RXOK_MASK)) { + if (isr & XCAN_IXR_RXNEMP_MASK) { ier = priv->read_reg(priv, XCAN_IER_OFFSET); - ier &= ~(XCAN_IXR_RXNEMP_MASK | XCAN_IXR_RXOK_MASK); + ier &= ~XCAN_IXR_RXNEMP_MASK; priv->write_reg(priv, XCAN_IER_OFFSET, ier); napi_schedule(&priv->napi); } -- 2.8.3

7 years, 3 months

1
0
0 0

[Linux-stable-mirror] [PATCH 1/5] can: xilinx_can: fix device dropping off bus on RX overrun

by Anssi Hannula

The xilinx_can driver performs a software reset when an RX overrun is detected. This causes the device to enter Configuration mode where no messages are received or transmitted. The documentation does not mention any need to perform a reset on an RX overrun, and testing by inducing an RX overflow also indicated that the device continues to work just fine without a reset. Remove the software reset. Tested with the integrated CAN on Zynq-7000 SoC. Fixes: b1201e44f50b ("can: xilinx CAN controller support") Signed-off-by: Anssi Hannula <anssi.hannula(a)bitwise.fi> Cc: <stable(a)vger.kernel.org> --- drivers/net/can/xilinx_can.c | 1 - 1 file changed, 1 deletion(-) diff --git a/drivers/net/can/xilinx_can.c b/drivers/net/can/xilinx_can.c index 89aec07..389a960 100644 --- a/drivers/net/can/xilinx_can.c +++ b/drivers/net/can/xilinx_can.c @@ -600,7 +600,6 @@ static void xcan_err_interrupt(struct net_device *ndev, u32 isr) if (isr & XCAN_IXR_RXOFLW_MASK) { stats->rx_over_errors++; stats->rx_errors++; - priv->write_reg(priv, XCAN_SRR_OFFSET, XCAN_SRR_RESET_MASK); if (skb) { cf->can_id |= CAN_ERR_CRTL; cf->data[1] |= CAN_ERR_CRTL_RX_OVERFLOW; -- 2.8.3

7 years, 3 months

1
0
0 0

[Linux-stable-mirror] patch "staging: lustre: separate a connection destroy from free struct" added to staging-testing

by gregkh＠linuxfoundation.org

This is a note to let you know that I've just added the patch titled staging: lustre: separate a connection destroy from free struct to my staging git tree which can be found at git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging.git in the staging-testing branch. The patch will show up in the next release of the linux-next tree (usually sometime within the next 24 hours during the week.) The patch will be merged to the staging-next branch sometime soon, after it passes testing, and the merge window is open. If you have any questions about this process, please let me know. >From 9b046013e5837f8a58453d1e9f8e01d03adb7fe7 Mon Sep 17 00:00:00 2001 From: Dmitry Eremin <dmitry.eremin(a)intel.com> Date: Thu, 25 Jan 2018 16:51:04 +0300 Subject: staging: lustre: separate a connection destroy from free struct kib_conn The logic of the original commit 4d99b2581eff ("staging: lustre: avoid intensive reconnecting for ko2iblnd") was assumed conditional free of struct kib_conn if the second argument free_conn in function kiblnd_destroy_conn(struct kib_conn *conn, bool free_conn) is true. But this hunk of code was dropped from original commit. As result the logic works wrong and current code use struct kib_conn after free. > drivers/staging/lustre/lnet/klnds/o2iblnd/o2iblnd_cb.c > 3317 kiblnd_destroy_conn(conn, !peer); > ^^^^ Freed always (but should be conditionally) > 3318 > 3319 spin_lock_irqsave(lock, flags); > 3320 if (!peer) > 3321 continue; > 3322 > 3323 conn->ibc_peer = peer; > ^^^^^^^^^^^^^^ Use after free > 3324 if (peer->ibp_reconnected < KIB_RECONN_HIGH_RACE) > 3325 list_add_tail(&conn->ibc_list, > ^^^^^^^^^^^^^^ Use after free > 3326 &kiblnd_data.kib_reconn_list); > 3327 else > 3328 list_add_tail(&conn->ibc_list, > ^^^^^^^^^^^^^^ Use after free > 3329 &kiblnd_data.kib_reconn_wait); To avoid confusion this fix moved the freeing a struct kib_conn outside of the function kiblnd_destroy_conn() and free as it was intended in original commit. Cc: <stable(a)vger.kernel.org> # v4.6 Fixes: 4d99b2581eff ("staging: lustre: avoid intensive reconnecting for ko2iblnd") Signed-off-by: Dmitry Eremin <Dmitry.Eremin(a)intel.com> Reviewed-by: Andreas Dilger <andreas.dilger(a)intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh(a)linuxfoundation.org> --- drivers/staging/lustre/lnet/klnds/o2iblnd/o2iblnd.c | 7 +++---- drivers/staging/lustre/lnet/klnds/o2iblnd/o2iblnd.h | 2 +- drivers/staging/lustre/lnet/klnds/o2iblnd/o2iblnd_cb.c | 6 ++++-- 3 files changed, 8 insertions(+), 7 deletions(-) diff --git a/drivers/staging/lustre/lnet/klnds/o2iblnd/o2iblnd.c b/drivers/staging/lustre/lnet/klnds/o2iblnd/o2iblnd.c index 2ebc484385b3..ec84edfda271 100644 --- a/drivers/staging/lustre/lnet/klnds/o2iblnd/o2iblnd.c +++ b/drivers/staging/lustre/lnet/klnds/o2iblnd/o2iblnd.c @@ -824,14 +824,15 @@ struct kib_conn *kiblnd_create_conn(struct kib_peer *peer, struct rdma_cm_id *cm return conn; failed_2: - kiblnd_destroy_conn(conn, true); + kiblnd_destroy_conn(conn); + kfree(conn); failed_1: kfree(init_qp_attr); failed_0: return NULL; } -void kiblnd_destroy_conn(struct kib_conn *conn, bool free_conn) +void kiblnd_destroy_conn(struct kib_conn *conn) { struct rdma_cm_id *cmid = conn->ibc_cmid; struct kib_peer *peer = conn->ibc_peer; @@ -889,8 +890,6 @@ void kiblnd_destroy_conn(struct kib_conn *conn, bool free_conn) rdma_destroy_id(cmid); atomic_dec(&net->ibn_nconns); } - - kfree(conn); } int kiblnd_close_peer_conns_locked(struct kib_peer *peer, int why) diff --git a/drivers/staging/lustre/lnet/klnds/o2iblnd/o2iblnd.h b/drivers/staging/lustre/lnet/klnds/o2iblnd/o2iblnd.h index 171eced213f8..b18911d09e9a 100644 --- a/drivers/staging/lustre/lnet/klnds/o2iblnd/o2iblnd.h +++ b/drivers/staging/lustre/lnet/klnds/o2iblnd/o2iblnd.h @@ -1016,7 +1016,7 @@ int kiblnd_close_peer_conns_locked(struct kib_peer *peer, int why); struct kib_conn *kiblnd_create_conn(struct kib_peer *peer, struct rdma_cm_id *cmid, int state, int version); -void kiblnd_destroy_conn(struct kib_conn *conn, bool free_conn); +void kiblnd_destroy_conn(struct kib_conn *conn); void kiblnd_close_conn(struct kib_conn *conn, int error); void kiblnd_close_conn_locked(struct kib_conn *conn, int error); diff --git a/drivers/staging/lustre/lnet/klnds/o2iblnd/o2iblnd_cb.c b/drivers/staging/lustre/lnet/klnds/o2iblnd/o2iblnd_cb.c index 9b3328c5d1e7..b3e7f28eb978 100644 --- a/drivers/staging/lustre/lnet/klnds/o2iblnd/o2iblnd_cb.c +++ b/drivers/staging/lustre/lnet/klnds/o2iblnd/o2iblnd_cb.c @@ -3314,11 +3314,13 @@ kiblnd_connd(void *arg) spin_unlock_irqrestore(lock, flags); dropped_lock = 1; - kiblnd_destroy_conn(conn, !peer); + kiblnd_destroy_conn(conn); spin_lock_irqsave(lock, flags); - if (!peer) + if (!peer) { + kfree(conn); continue; + } conn->ibc_peer = peer; if (peer->ibp_reconnected < KIB_RECONN_HIGH_RACE) -- 2.16.1

7 years, 3 months

1
0
0 0

[Linux-stable-mirror] Patch "ARM: net: bpf: fix tail call jumps" has been added to the 4.14-stable tree

by gregkh＠linuxfoundation.org

This is a note to let you know that I've just added the patch titled ARM: net: bpf: fix tail call jumps to the 4.14-stable tree which can be found at: http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=sum… The filename of the patch is: arm-net-bpf-fix-tail-call-jumps.patch and it can be found in the queue-4.14 subdirectory. If you, or anyone else, feels it should not be added to the stable tree, please let <stable(a)vger.kernel.org> know about it. >From f4483f2cc1fdc03488c8a1452e545545ae5bda93 Mon Sep 17 00:00:00 2001 From: Russell King <rmk+kernel(a)armlinux.org.uk> Date: Sat, 13 Jan 2018 11:39:54 +0000 Subject: ARM: net: bpf: fix tail call jumps From: Russell King <rmk+kernel(a)armlinux.org.uk> commit f4483f2cc1fdc03488c8a1452e545545ae5bda93 upstream. When a tail call fails, it is documented that the tail call should continue execution at the following instruction. An example tail call sequence is: 12: (85) call bpf_tail_call#12 13: (b7) r0 = 0 14: (95) exit The ARM assembler for the tail call in this case ends up branching to instruction 14 instead of instruction 13, resulting in the BPF filter returning a non-zero value: 178: ldr r8, [sp, #588] ; insn 12 17c: ldr r6, [r8, r6] 180: ldr r8, [sp, #580] 184: cmp r8, r6 188: bcs 0x1e8 18c: ldr r6, [sp, #524] 190: ldr r7, [sp, #528] 194: cmp r7, #0 198: cmpeq r6, #32 19c: bhi 0x1e8 1a0: adds r6, r6, #1 1a4: adc r7, r7, #0 1a8: str r6, [sp, #524] 1ac: str r7, [sp, #528] 1b0: mov r6, #104 1b4: ldr r8, [sp, #588] 1b8: add r6, r8, r6 1bc: ldr r8, [sp, #580] 1c0: lsl r7, r8, #2 1c4: ldr r6, [r6, r7] 1c8: cmp r6, #0 1cc: beq 0x1e8 1d0: mov r8, #32 1d4: ldr r6, [r6, r8] 1d8: add r6, r6, #44 1dc: bx r6 1e0: mov r0, #0 ; insn 13 1e4: mov r1, #0 1e8: add sp, sp, #596 ; insn 14 1ec: pop {r4, r5, r6, r7, r8, sl, pc} For other sequences, the tail call could end up branching midway through the following BPF instructions, or maybe off the end of the function, leading to unknown behaviours. Fixes: 39c13c204bb1 ("arm: eBPF JIT compiler") Signed-off-by: Russell King <rmk+kernel(a)armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh(a)linuxfoundation.org> --- arch/arm/net/bpf_jit_32.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) --- a/arch/arm/net/bpf_jit_32.c +++ b/arch/arm/net/bpf_jit_32.c @@ -949,7 +949,7 @@ static int emit_bpf_tail_call(struct jit const u8 *tcc = bpf2a32[TCALL_CNT]; const int idx0 = ctx->idx; #define cur_offset (ctx->idx - idx0) -#define jmp_offset (out_offset - (cur_offset)) +#define jmp_offset (out_offset - (cur_offset) - 2) u32 off, lo, hi; /* if (index >= array->map.max_entries) Patches currently in stable-queue which might be from rmk+kernel(a)armlinux.org.uk are queue-4.14/arm-net-bpf-fix-stack-alignment.patch queue-4.14/arm-net-bpf-fix-ldx-instructions.patch queue-4.14/arm-net-bpf-fix-register-saving.patch queue-4.14/arm-net-bpf-move-stack-documentation.patch queue-4.14/arm-net-bpf-correct-stack-layout-documentation.patch queue-4.14/arm-net-bpf-clarify-tail_call-index.patch queue-4.14/arm-net-bpf-avoid-bx-instruction-on-non-thumb-capable-cpus.patch queue-4.14/arm-net-bpf-fix-tail-call-jumps.patch

7 years, 3 months

1
0
0 0

[Linux-stable-mirror] Patch "ARM: net: bpf: move stack documentation" has been added to the 4.14-stable tree

by gregkh＠linuxfoundation.org

This is a note to let you know that I've just added the patch titled ARM: net: bpf: move stack documentation to the 4.14-stable tree which can be found at: http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=sum… The filename of the patch is: arm-net-bpf-move-stack-documentation.patch and it can be found in the queue-4.14 subdirectory. If you, or anyone else, feels it should not be added to the stable tree, please let <stable(a)vger.kernel.org> know about it. >From 70ec3a6c2c11e4b0e107a65de943a082f9aff351 Mon Sep 17 00:00:00 2001 From: Russell King <rmk+kernel(a)armlinux.org.uk> Date: Sat, 13 Jan 2018 21:26:14 +0000 Subject: ARM: net: bpf: move stack documentation From: Russell King <rmk+kernel(a)armlinux.org.uk> commit 70ec3a6c2c11e4b0e107a65de943a082f9aff351 upstream. Move the stack documentation towards the top of the file, where it's relevant for things like the register layout. Signed-off-by: Russell King <rmk+kernel(a)armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh(a)linuxfoundation.org> --- arch/arm/net/bpf_jit_32.c | 42 +++++++++++++++++++++--------------------- 1 file changed, 21 insertions(+), 21 deletions(-) --- a/arch/arm/net/bpf_jit_32.c +++ b/arch/arm/net/bpf_jit_32.c @@ -27,6 +27,27 @@ int bpf_jit_enable __read_mostly; +/* + * eBPF prog stack layout + * + * high + * original ARM_SP => +-----+ eBPF prologue + * |FP/LR| + * current ARM_FP => +-----+ + * | ... | callee saved registers + * eBPF fp register => +-----+ <= (BPF_FP) + * | ... | eBPF JIT scratch space + * | | eBPF prog stack + * +-----+ + * |RSVD | JIT scratchpad + * current ARM_SP => +-----+ <= (BPF_FP - STACK_SIZE) + * | | + * | ... | Function call stack + * | | + * +-----+ + * low + */ + #define STACK_OFFSET(k) (k) #define TMP_REG_1 (MAX_BPF_JIT_REG + 0) /* TEMP Register 1 */ #define TMP_REG_2 (MAX_BPF_JIT_REG + 1) /* TEMP Register 2 */ @@ -1091,27 +1112,6 @@ static void build_prologue(struct jit_ct u16 reg_set = 0; - /* - * eBPF prog stack layout - * - * high - * original ARM_SP => +-----+ eBPF prologue - * |FP/LR| - * current ARM_FP => +-----+ - * | ... | callee saved registers - * eBPF fp register => +-----+ <= (BPF_FP) - * | ... | eBPF JIT scratch space - * | | eBPF prog stack - * +-----+ - * |RSVD | JIT scratchpad - * current A64_SP => +-----+ <= (BPF_FP - STACK_SIZE) - * | | - * | ... | Function call stack - * | | - * +-----+ - * low - */ - /* Save callee saved registers. */ reg_set |= (1<<r4) | (1<<r5) | (1<<r6) | (1<<r7) | (1<<r8) | (1<<r10); #ifdef CONFIG_FRAME_POINTER Patches currently in stable-queue which might be from rmk+kernel(a)armlinux.org.uk are queue-4.14/arm-net-bpf-fix-stack-alignment.patch queue-4.14/arm-net-bpf-fix-ldx-instructions.patch queue-4.14/arm-net-bpf-fix-register-saving.patch queue-4.14/arm-net-bpf-move-stack-documentation.patch queue-4.14/arm-net-bpf-correct-stack-layout-documentation.patch queue-4.14/arm-net-bpf-clarify-tail_call-index.patch queue-4.14/arm-net-bpf-avoid-bx-instruction-on-non-thumb-capable-cpus.patch queue-4.14/arm-net-bpf-fix-tail-call-jumps.patch

7 years, 3 months

1
0
0 0

[Linux-stable-mirror] Patch "ARM: net: bpf: fix stack alignment" has been added to the 4.14-stable tree

by gregkh＠linuxfoundation.org

This is a note to let you know that I've just added the patch titled ARM: net: bpf: fix stack alignment to the 4.14-stable tree which can be found at: http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=sum… The filename of the patch is: arm-net-bpf-fix-stack-alignment.patch and it can be found in the queue-4.14 subdirectory. If you, or anyone else, feels it should not be added to the stable tree, please let <stable(a)vger.kernel.org> know about it. >From d1220efd23484c72c82d5471f05daeb35b5d1916 Mon Sep 17 00:00:00 2001 From: Russell King <rmk+kernel(a)armlinux.org.uk> Date: Sat, 13 Jan 2018 16:10:07 +0000 Subject: ARM: net: bpf: fix stack alignment From: Russell King <rmk+kernel(a)armlinux.org.uk> commit d1220efd23484c72c82d5471f05daeb35b5d1916 upstream. As per 2dede2d8e925 ("ARM EABI: stack pointer must be 64-bit aligned after a CPU exception") the stack should be aligned to a 64-bit boundary on EABI systems. Ensure that the eBPF JIT appropraitely aligns the stack. Fixes: 39c13c204bb1 ("arm: eBPF JIT compiler") Signed-off-by: Russell King <rmk+kernel(a)armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh(a)linuxfoundation.org> --- arch/arm/net/bpf_jit_32.c | 11 ++++++++--- 1 file changed, 8 insertions(+), 3 deletions(-) --- a/arch/arm/net/bpf_jit_32.c +++ b/arch/arm/net/bpf_jit_32.c @@ -179,8 +179,13 @@ static void jit_fill_hole(void *area, un *ptr++ = __opcode_to_mem_arm(ARM_INST_UDF); } -/* Stack must be multiples of 16 Bytes */ -#define STACK_ALIGN(sz) (((sz) + 3) & ~3) +#if defined(CONFIG_AEABI) && (__LINUX_ARM_ARCH__ >= 5) +/* EABI requires the stack to be aligned to 64-bit boundaries */ +#define STACK_ALIGNMENT 8 +#else +/* Stack must be aligned to 32-bit boundaries */ +#define STACK_ALIGNMENT 4 +#endif /* Stack space for BPF_REG_2, BPF_REG_3, BPF_REG_4, * BPF_REG_5, BPF_REG_7, BPF_REG_8, BPF_REG_9, @@ -194,7 +199,7 @@ static void jit_fill_hole(void *area, un + SCRATCH_SIZE + \ + 4 /* extra for skb_copy_bits buffer */) -#define STACK_SIZE STACK_ALIGN(_STACK_SIZE) +#define STACK_SIZE ALIGN(_STACK_SIZE, STACK_ALIGNMENT) /* Get the offset of eBPF REGISTERs stored on scratch space. */ #define STACK_VAR(off) (STACK_SIZE-off-4) Patches currently in stable-queue which might be from rmk+kernel(a)armlinux.org.uk are queue-4.14/arm-net-bpf-fix-stack-alignment.patch queue-4.14/arm-net-bpf-fix-ldx-instructions.patch queue-4.14/arm-net-bpf-fix-register-saving.patch queue-4.14/arm-net-bpf-move-stack-documentation.patch queue-4.14/arm-net-bpf-correct-stack-layout-documentation.patch queue-4.14/arm-net-bpf-clarify-tail_call-index.patch queue-4.14/arm-net-bpf-avoid-bx-instruction-on-non-thumb-capable-cpus.patch queue-4.14/arm-net-bpf-fix-tail-call-jumps.patch

7 years, 3 months

1
0
0 0

[Linux-stable-mirror] Patch "ARM: net: bpf: fix register saving" has been added to the 4.14-stable tree

by gregkh＠linuxfoundation.org

This is a note to let you know that I've just added the patch titled ARM: net: bpf: fix register saving to the 4.14-stable tree which can be found at: http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=sum… The filename of the patch is: arm-net-bpf-fix-register-saving.patch and it can be found in the queue-4.14 subdirectory. If you, or anyone else, feels it should not be added to the stable tree, please let <stable(a)vger.kernel.org> know about it. >From 02088d9b392f605c892894b46aa8c83e3abd0115 Mon Sep 17 00:00:00 2001 From: Russell King <rmk+kernel(a)armlinux.org.uk> Date: Sat, 13 Jan 2018 22:38:18 +0000 Subject: ARM: net: bpf: fix register saving From: Russell King <rmk+kernel(a)armlinux.org.uk> commit 02088d9b392f605c892894b46aa8c83e3abd0115 upstream. When an eBPF program tail-calls another eBPF program, it enters it after the prologue to avoid having complex stack manipulations. This can lead to kernel oopses, and similar. Resolve this by always using a fixed stack layout, a CPU register frame pointer, and using this when reloading registers before returning. Fixes: 39c13c204bb1 ("arm: eBPF JIT compiler") Signed-off-by: Russell King <rmk+kernel(a)armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh(a)linuxfoundation.org> --- arch/arm/net/bpf_jit_32.c | 80 ++++++++++++---------------------------------- 1 file changed, 22 insertions(+), 58 deletions(-) --- a/arch/arm/net/bpf_jit_32.c +++ b/arch/arm/net/bpf_jit_32.c @@ -61,20 +61,24 @@ int bpf_jit_enable __read_mostly; * * high * original ARM_SP => +------------------+ - * | lr | (optional) - * | r4-r8,r10 | callee saved registers - * +------------------+ + * | r4-r8,r10,fp,lr | callee saved registers + * current ARM_FP => +------------------+ * low + * + * When popping registers off the stack at the end of a BPF function, we + * reference them via the current ARM_FP register. */ +#define CALLEE_MASK (1 << ARM_R4 | 1 << ARM_R5 | 1 << ARM_R6 | \ + 1 << ARM_R7 | 1 << ARM_R8 | 1 << ARM_R10 | \ + 1 << ARM_FP) +#define CALLEE_PUSH_MASK (CALLEE_MASK | 1 << ARM_LR) +#define CALLEE_POP_MASK (CALLEE_MASK | 1 << ARM_PC) #define STACK_OFFSET(k) (k) #define TMP_REG_1 (MAX_BPF_JIT_REG + 0) /* TEMP Register 1 */ #define TMP_REG_2 (MAX_BPF_JIT_REG + 1) /* TEMP Register 2 */ #define TCALL_CNT (MAX_BPF_JIT_REG + 2) /* Tail Call Count */ -/* Flags used for JIT optimization */ -#define SEEN_CALL (1 << 0) - #define FLAG_IMM_OVERFLOW (1 << 0) /* @@ -135,7 +139,6 @@ static const u8 bpf2a32[][2] = { * idx : index of current last JITed instruction. * prologue_bytes : bytes used in prologue. * epilogue_offset : offset of epilogue starting. - * seen : bit mask used for JIT optimization. * offsets : array of eBPF instruction offsets in * JITed code. * target : final JITed code. @@ -150,7 +153,6 @@ struct jit_ctx { unsigned int idx; unsigned int prologue_bytes; unsigned int epilogue_offset; - u32 seen; u32 flags; u32 *offsets; u32 *target; @@ -340,7 +342,6 @@ static void emit_bx_r(u8 tgt_reg, struct static inline void emit_blx_r(u8 tgt_reg, struct jit_ctx *ctx) { - ctx->seen |= SEEN_CALL; #if __LINUX_ARM_ARCH__ < 5 emit(ARM_MOV_R(ARM_LR, ARM_PC), ctx); emit_bx_r(tgt_reg, ctx); @@ -403,7 +404,6 @@ static inline void emit_udivmod(u8 rd, u } /* Call appropriate function */ - ctx->seen |= SEEN_CALL; emit_mov_i(ARM_IP, op == BPF_DIV ? (u32)jit_udiv32 : (u32)jit_mod32, ctx); emit_blx_r(ARM_IP, ctx); @@ -669,8 +669,6 @@ static inline void emit_a32_lsh_r64(cons /* Do LSH operation */ emit(ARM_SUB_I(ARM_IP, rt, 32), ctx); emit(ARM_RSB_I(tmp2[0], rt, 32), ctx); - /* As we are using ARM_LR */ - ctx->seen |= SEEN_CALL; emit(ARM_MOV_SR(ARM_LR, rm, SRTYPE_ASL, rt), ctx); emit(ARM_ORR_SR(ARM_LR, ARM_LR, rd, SRTYPE_ASL, ARM_IP), ctx); emit(ARM_ORR_SR(ARM_IP, ARM_LR, rd, SRTYPE_LSR, tmp2[0]), ctx); @@ -705,8 +703,6 @@ static inline void emit_a32_arsh_r64(con /* Do the ARSH operation */ emit(ARM_RSB_I(ARM_IP, rt, 32), ctx); emit(ARM_SUBS_I(tmp2[0], rt, 32), ctx); - /* As we are using ARM_LR */ - ctx->seen |= SEEN_CALL; emit(ARM_MOV_SR(ARM_LR, rd, SRTYPE_LSR, rt), ctx); emit(ARM_ORR_SR(ARM_LR, ARM_LR, rm, SRTYPE_ASL, ARM_IP), ctx); _emit(ARM_COND_MI, ARM_B(0), ctx); @@ -741,8 +737,6 @@ static inline void emit_a32_lsr_r64(cons /* Do LSH operation */ emit(ARM_RSB_I(ARM_IP, rt, 32), ctx); emit(ARM_SUBS_I(tmp2[0], rt, 32), ctx); - /* As we are using ARM_LR */ - ctx->seen |= SEEN_CALL; emit(ARM_MOV_SR(ARM_LR, rd, SRTYPE_LSR, rt), ctx); emit(ARM_ORR_SR(ARM_LR, ARM_LR, rm, SRTYPE_ASL, ARM_IP), ctx); emit(ARM_ORR_SR(ARM_LR, ARM_LR, rm, SRTYPE_LSR, tmp2[0]), ctx); @@ -877,8 +871,6 @@ static inline void emit_a32_mul_r64(cons /* Do Multiplication */ emit(ARM_MUL(ARM_IP, rd, rn), ctx); emit(ARM_MUL(ARM_LR, rm, rt), ctx); - /* As we are using ARM_LR */ - ctx->seen |= SEEN_CALL; emit(ARM_ADD_R(ARM_LR, ARM_IP, ARM_LR), ctx); emit(ARM_UMULL(ARM_IP, rm, rd, rt), ctx); @@ -955,7 +947,6 @@ static inline void emit_ar_r(const u8 rd const u8 rn, struct jit_ctx *ctx, u8 op) { switch (op) { case BPF_JSET: - ctx->seen |= SEEN_CALL; emit(ARM_AND_R(ARM_IP, rt, rn), ctx); emit(ARM_AND_R(ARM_LR, rd, rm), ctx); emit(ARM_ORRS_R(ARM_IP, ARM_LR, ARM_IP), ctx); @@ -1119,33 +1110,22 @@ static void build_prologue(struct jit_ct const u8 r2 = bpf2a32[BPF_REG_1][1]; const u8 r3 = bpf2a32[BPF_REG_1][0]; const u8 r4 = bpf2a32[BPF_REG_6][1]; - const u8 r5 = bpf2a32[BPF_REG_6][0]; - const u8 r6 = bpf2a32[TMP_REG_1][1]; - const u8 r7 = bpf2a32[TMP_REG_1][0]; - const u8 r8 = bpf2a32[TMP_REG_2][1]; - const u8 r10 = bpf2a32[TMP_REG_2][0]; const u8 fplo = bpf2a32[BPF_REG_FP][1]; const u8 fphi = bpf2a32[BPF_REG_FP][0]; - const u8 sp = ARM_SP; const u8 *tcc = bpf2a32[TCALL_CNT]; - u16 reg_set = 0; - /* Save callee saved registers. */ - reg_set |= (1<<r4) | (1<<r5) | (1<<r6) | (1<<r7) | (1<<r8) | (1<<r10); #ifdef CONFIG_FRAME_POINTER - reg_set |= (1<<ARM_FP) | (1<<ARM_IP) | (1<<ARM_LR) | (1<<ARM_PC); - emit(ARM_MOV_R(ARM_IP, sp), ctx); + u16 reg_set = CALLEE_PUSH_MASK | 1 << ARM_IP | 1 << ARM_PC; + emit(ARM_MOV_R(ARM_IP, ARM_SP), ctx); emit(ARM_PUSH(reg_set), ctx); emit(ARM_SUB_I(ARM_FP, ARM_IP, 4), ctx); #else - /* Check if call instruction exists in BPF body */ - if (ctx->seen & SEEN_CALL) - reg_set |= (1<<ARM_LR); - emit(ARM_PUSH(reg_set), ctx); + emit(ARM_PUSH(CALLEE_PUSH_MASK), ctx); + emit(ARM_MOV_R(ARM_FP, ARM_SP), ctx); #endif /* Save frame pointer for later */ - emit(ARM_SUB_I(ARM_IP, sp, SCRATCH_SIZE), ctx); + emit(ARM_SUB_I(ARM_IP, ARM_SP, SCRATCH_SIZE), ctx); ctx->stack_size = imm8m(STACK_SIZE); @@ -1168,33 +1148,19 @@ static void build_prologue(struct jit_ct /* end of prologue */ } +/* restore callee saved registers. */ static void build_epilogue(struct jit_ctx *ctx) { - const u8 r4 = bpf2a32[BPF_REG_6][1]; - const u8 r5 = bpf2a32[BPF_REG_6][0]; - const u8 r6 = bpf2a32[TMP_REG_1][1]; - const u8 r7 = bpf2a32[TMP_REG_1][0]; - const u8 r8 = bpf2a32[TMP_REG_2][1]; - const u8 r10 = bpf2a32[TMP_REG_2][0]; - u16 reg_set = 0; - - /* unwind function call stack */ - emit(ARM_ADD_I(ARM_SP, ARM_SP, ctx->stack_size), ctx); - - /* restore callee saved registers. */ - reg_set |= (1<<r4) | (1<<r5) | (1<<r6) | (1<<r7) | (1<<r8) | (1<<r10); #ifdef CONFIG_FRAME_POINTER - /* the first instruction of the prologue was: mov ip, sp */ - reg_set |= (1<<ARM_FP) | (1<<ARM_SP) | (1<<ARM_PC); + /* When using frame pointers, some additional registers need to + * be loaded. */ + u16 reg_set = CALLEE_POP_MASK | 1 << ARM_SP; + emit(ARM_SUB_I(ARM_SP, ARM_FP, hweight16(reg_set) * 4), ctx); emit(ARM_LDM(ARM_SP, reg_set), ctx); #else - if (ctx->seen & SEEN_CALL) - reg_set |= (1<<ARM_PC); /* Restore callee saved registers. */ - emit(ARM_POP(reg_set), ctx); - /* Return back to the callee function */ - if (!(ctx->seen & SEEN_CALL)) - emit_bx_r(ARM_LR, ctx); + emit(ARM_MOV_R(ARM_SP, ARM_FP), ctx); + emit(ARM_POP(CALLEE_POP_MASK), ctx); #endif } @@ -1422,8 +1388,6 @@ static int build_insn(const struct bpf_i emit_rev32(rt, rt, ctx); goto emit_bswap_uxt; case 64: - /* Because of the usage of ARM_LR */ - ctx->seen |= SEEN_CALL; emit_rev32(ARM_LR, rt, ctx); emit_rev32(rt, rd, ctx); emit(ARM_MOV_R(rd, ARM_LR), ctx); Patches currently in stable-queue which might be from rmk+kernel(a)armlinux.org.uk are queue-4.14/arm-net-bpf-fix-stack-alignment.patch queue-4.14/arm-net-bpf-fix-ldx-instructions.patch queue-4.14/arm-net-bpf-fix-register-saving.patch queue-4.14/arm-net-bpf-move-stack-documentation.patch queue-4.14/arm-net-bpf-correct-stack-layout-documentation.patch queue-4.14/arm-net-bpf-clarify-tail_call-index.patch queue-4.14/arm-net-bpf-avoid-bx-instruction-on-non-thumb-capable-cpus.patch queue-4.14/arm-net-bpf-fix-tail-call-jumps.patch

7 years, 3 months

1
0
0 0

[Linux-stable-mirror] Patch "ARM: net: bpf: fix LDX instructions" has been added to the 4.14-stable tree

by gregkh＠linuxfoundation.org

This is a note to let you know that I've just added the patch titled ARM: net: bpf: fix LDX instructions to the 4.14-stable tree which can be found at: http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=sum… The filename of the patch is: arm-net-bpf-fix-ldx-instructions.patch and it can be found in the queue-4.14 subdirectory. If you, or anyone else, feels it should not be added to the stable tree, please let <stable(a)vger.kernel.org> know about it. >From ec19e02b343db991d2d1610c409efefebf4e2ca9 Mon Sep 17 00:00:00 2001 From: Russell King <rmk+kernel(a)armlinux.org.uk> Date: Sat, 13 Jan 2018 21:06:16 +0000 Subject: ARM: net: bpf: fix LDX instructions From: Russell King <rmk+kernel(a)armlinux.org.uk> commit ec19e02b343db991d2d1610c409efefebf4e2ca9 upstream. When the source and destination register are identical, our JIT does not generate correct code, which leads to kernel oopses. Fix this by (a) generating more efficient code, and (b) making use of the temporary earlier if we will overwrite the address register. Fixes: 39c13c204bb1 ("arm: eBPF JIT compiler") Signed-off-by: Russell King <rmk+kernel(a)armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh(a)linuxfoundation.org> --- arch/arm/net/bpf_jit_32.c | 61 ++++++++++++++++++++++++---------------------- 1 file changed, 33 insertions(+), 28 deletions(-) --- a/arch/arm/net/bpf_jit_32.c +++ b/arch/arm/net/bpf_jit_32.c @@ -913,33 +913,53 @@ static inline void emit_str_r(const u8 d } /* dst = *(size*)(src + off) */ -static inline void emit_ldx_r(const u8 dst, const u8 src, bool dstk, - const s32 off, struct jit_ctx *ctx, const u8 sz){ +static inline void emit_ldx_r(const u8 dst[], const u8 src, bool dstk, + s32 off, struct jit_ctx *ctx, const u8 sz){ const u8 *tmp = bpf2a32[TMP_REG_1]; - u8 rd = dstk ? tmp[1] : dst; + const u8 *rd = dstk ? tmp : dst; u8 rm = src; + s32 off_max; - if (off) { + if (sz == BPF_H) + off_max = 0xff; + else + off_max = 0xfff; + + if (off < 0 || off > off_max) { emit_a32_mov_i(tmp[0], off, false, ctx); emit(ARM_ADD_R(tmp[0], tmp[0], src), ctx); rm = tmp[0]; + off = 0; + } else if (rd[1] == rm) { + emit(ARM_MOV_R(tmp[0], rm), ctx); + rm = tmp[0]; } switch (sz) { - case BPF_W: - /* Load a Word */ - emit(ARM_LDR_I(rd, rm, 0), ctx); + case BPF_B: + /* Load a Byte */ + emit(ARM_LDRB_I(rd[1], rm, off), ctx); + emit_a32_mov_i(dst[0], 0, dstk, ctx); break; case BPF_H: /* Load a HalfWord */ - emit(ARM_LDRH_I(rd, rm, 0), ctx); + emit(ARM_LDRH_I(rd[1], rm, off), ctx); + emit_a32_mov_i(dst[0], 0, dstk, ctx); break; - case BPF_B: - /* Load a Byte */ - emit(ARM_LDRB_I(rd, rm, 0), ctx); + case BPF_W: + /* Load a Word */ + emit(ARM_LDR_I(rd[1], rm, off), ctx); + emit_a32_mov_i(dst[0], 0, dstk, ctx); + break; + case BPF_DW: + /* Load a Double Word */ + emit(ARM_LDR_I(rd[1], rm, off), ctx); + emit(ARM_LDR_I(rd[0], rm, off + 4), ctx); break; } if (dstk) - emit(ARM_STR_I(rd, ARM_SP, STACK_VAR(dst)), ctx); + emit(ARM_STR_I(rd[1], ARM_SP, STACK_VAR(dst[1])), ctx); + if (dstk && sz == BPF_DW) + emit(ARM_STR_I(rd[0], ARM_SP, STACK_VAR(dst[0])), ctx); } /* Arithmatic Operation */ @@ -1440,22 +1460,7 @@ exit: rn = sstk ? tmp2[1] : src_lo; if (sstk) emit(ARM_LDR_I(rn, ARM_SP, STACK_VAR(src_lo)), ctx); - switch (BPF_SIZE(code)) { - case BPF_W: - /* Load a Word */ - case BPF_H: - /* Load a Half-Word */ - case BPF_B: - /* Load a Byte */ - emit_ldx_r(dst_lo, rn, dstk, off, ctx, BPF_SIZE(code)); - emit_a32_mov_i(dst_hi, 0, dstk, ctx); - break; - case BPF_DW: - /* Load a double word */ - emit_ldx_r(dst_lo, rn, dstk, off, ctx, BPF_W); - emit_ldx_r(dst_hi, rn, dstk, off+4, ctx, BPF_W); - break; - } + emit_ldx_r(dst, rn, dstk, off, ctx, BPF_SIZE(code)); break; /* R0 = ntohx(*(size *)(((struct sk_buff *)R6)->data + imm)) */ case BPF_LD | BPF_ABS | BPF_W: Patches currently in stable-queue which might be from rmk+kernel(a)armlinux.org.uk are queue-4.14/arm-net-bpf-fix-stack-alignment.patch queue-4.14/arm-net-bpf-fix-ldx-instructions.patch queue-4.14/arm-net-bpf-fix-register-saving.patch queue-4.14/arm-net-bpf-move-stack-documentation.patch queue-4.14/arm-net-bpf-correct-stack-layout-documentation.patch queue-4.14/arm-net-bpf-clarify-tail_call-index.patch queue-4.14/arm-net-bpf-avoid-bx-instruction-on-non-thumb-capable-cpus.patch queue-4.14/arm-net-bpf-fix-tail-call-jumps.patch

7 years, 3 months

1
0
0 0

[Linux-stable-mirror] Patch "ARM: net: bpf: clarify tail_call index" has been added to the 4.14-stable tree

by gregkh＠linuxfoundation.org

This is a note to let you know that I've just added the patch titled ARM: net: bpf: clarify tail_call index to the 4.14-stable tree which can be found at: http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=sum… The filename of the patch is: arm-net-bpf-clarify-tail_call-index.patch and it can be found in the queue-4.14 subdirectory. If you, or anyone else, feels it should not be added to the stable tree, please let <stable(a)vger.kernel.org> know about it. >From 091f02483df7b56615b524491f404e574c5e0668 Mon Sep 17 00:00:00 2001 From: Russell King <rmk+kernel(a)armlinux.org.uk> Date: Sat, 13 Jan 2018 12:11:26 +0000 Subject: ARM: net: bpf: clarify tail_call index From: Russell King <rmk+kernel(a)armlinux.org.uk> commit 091f02483df7b56615b524491f404e574c5e0668 upstream. As per 90caccdd8cc0 ("bpf: fix bpf_tail_call() x64 JIT"), the index used for array lookup is defined to be 32-bit wide. Update a misleading comment that suggests it is 64-bit wide. Fixes: 39c13c204bb1 ("arm: eBPF JIT compiler") Signed-off-by: Russell King <rmk+kernel(a)armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh(a)linuxfoundation.org> --- arch/arm/net/bpf_jit_32.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) --- a/arch/arm/net/bpf_jit_32.c +++ b/arch/arm/net/bpf_jit_32.c @@ -1016,7 +1016,7 @@ static int emit_bpf_tail_call(struct jit emit_a32_mov_i(tmp[1], off, false, ctx); emit(ARM_LDR_I(tmp2[1], ARM_SP, STACK_VAR(r2[1])), ctx); emit(ARM_LDR_R(tmp[1], tmp2[1], tmp[1]), ctx); - /* index (64 bit) */ + /* index is 32-bit for arrays */ emit(ARM_LDR_I(tmp2[1], ARM_SP, STACK_VAR(r3[1])), ctx); /* index >= array->map.max_entries */ emit(ARM_CMP_R(tmp2[1], tmp[1]), ctx); Patches currently in stable-queue which might be from rmk+kernel(a)armlinux.org.uk are queue-4.14/arm-net-bpf-fix-stack-alignment.patch queue-4.14/arm-net-bpf-fix-ldx-instructions.patch queue-4.14/arm-net-bpf-fix-register-saving.patch queue-4.14/arm-net-bpf-move-stack-documentation.patch queue-4.14/arm-net-bpf-correct-stack-layout-documentation.patch queue-4.14/arm-net-bpf-clarify-tail_call-index.patch queue-4.14/arm-net-bpf-avoid-bx-instruction-on-non-thumb-capable-cpus.patch queue-4.14/arm-net-bpf-fix-tail-call-jumps.patch

7 years, 3 months

1
0
0 0

[Linux-stable-mirror] Patch "ARM: net: bpf: correct stack layout documentation" has been added to the 4.14-stable tree

by gregkh＠linuxfoundation.org

This is a note to let you know that I've just added the patch titled ARM: net: bpf: correct stack layout documentation to the 4.14-stable tree which can be found at: http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=sum… The filename of the patch is: arm-net-bpf-correct-stack-layout-documentation.patch and it can be found in the queue-4.14 subdirectory. If you, or anyone else, feels it should not be added to the stable tree, please let <stable(a)vger.kernel.org> know about it. >From 0005e55a79cfda88199e41a406a829c88d708c67 Mon Sep 17 00:00:00 2001 From: Russell King <rmk+kernel(a)armlinux.org.uk> Date: Sat, 13 Jan 2018 22:51:27 +0000 Subject: ARM: net: bpf: correct stack layout documentation From: Russell King <rmk+kernel(a)armlinux.org.uk> commit 0005e55a79cfda88199e41a406a829c88d708c67 upstream. The stack layout documentation incorrectly suggests that the BPF JIT scratch space starts immediately below BPF_FP. This is not correct, so let's fix the documentation to reflect reality. Signed-off-by: Russell King <rmk+kernel(a)armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh(a)linuxfoundation.org> --- arch/arm/net/bpf_jit_32.c | 35 +++++++++++++++++++++++++++-------- 1 file changed, 27 insertions(+), 8 deletions(-) --- a/arch/arm/net/bpf_jit_32.c +++ b/arch/arm/net/bpf_jit_32.c @@ -28,24 +28,43 @@ int bpf_jit_enable __read_mostly; /* - * eBPF prog stack layout + * eBPF prog stack layout: * * high - * original ARM_SP => +-----+ eBPF prologue - * |FP/LR| - * current ARM_FP => +-----+ - * | ... | callee saved registers - * eBPF fp register => +-----+ <= (BPF_FP) + * original ARM_SP => +-----+ + * | | callee saved registers + * +-----+ <= (BPF_FP + SCRATCH_SIZE) * | ... | eBPF JIT scratch space - * | | eBPF prog stack + * eBPF fp register => +-----+ + * (BPF_FP) | ... | eBPF prog stack * +-----+ * |RSVD | JIT scratchpad - * current ARM_SP => +-----+ <= (BPF_FP - STACK_SIZE) + * current ARM_SP => +-----+ <= (BPF_FP - STACK_SIZE + SCRATCH_SIZE) * | | * | ... | Function call stack * | | * +-----+ * low + * + * The callee saved registers depends on whether frame pointers are enabled. + * With frame pointers (to be compliant with the ABI): + * + * high + * original ARM_SP => +------------------+ \ + * | pc | | + * current ARM_FP => +------------------+ } callee saved registers + * |r4-r8,r10,fp,ip,lr| | + * +------------------+ / + * low + * + * Without frame pointers: + * + * high + * original ARM_SP => +------------------+ + * | lr | (optional) + * | r4-r8,r10 | callee saved registers + * +------------------+ + * low */ #define STACK_OFFSET(k) (k) Patches currently in stable-queue which might be from rmk+kernel(a)armlinux.org.uk are queue-4.14/arm-net-bpf-fix-stack-alignment.patch queue-4.14/arm-net-bpf-fix-ldx-instructions.patch queue-4.14/arm-net-bpf-fix-register-saving.patch queue-4.14/arm-net-bpf-move-stack-documentation.patch queue-4.14/arm-net-bpf-correct-stack-layout-documentation.patch queue-4.14/arm-net-bpf-clarify-tail_call-index.patch queue-4.14/arm-net-bpf-avoid-bx-instruction-on-non-thumb-capable-cpus.patch queue-4.14/arm-net-bpf-fix-tail-call-jumps.patch

7 years, 3 months

1
0
0 0

2025

2024

2023

2022

2021

2020

2019

2018

2017

Linux-stable-mirror