- Linux-stable-mirror - lists.linaro.org

FAILED: patch "[PATCH] tpm_tis: fix potential buffer overruns caused by bit glitches" failed to apply to 4.4-stable tree

by gregkh＠linuxfoundation.org

The patch below does not apply to the 4.4-stable tree. If someone wants it applied there, or to any other stable or longterm tree, then please email the backport, including the original git commit id to <stable(a)vger.kernel.org>. thanks, greg k-h ------------------ original commit in Linus's tree ------------------ >From 6bb320ca4a4a7b5b3db8c8d7250cc40002046878 Mon Sep 17 00:00:00 2001 From: Jeremy Boone <jeremy.boone(a)nccgroup.trust> Date: Thu, 8 Feb 2018 12:32:06 -0800 Subject: [PATCH] tpm_tis: fix potential buffer overruns caused by bit glitches on the bus Discrete TPMs are often connected over slow serial buses which, on some platforms, can have glitches causing bit flips. In all the driver _recv() functions, we need to use a u32 to unmarshal the response size, otherwise a bit flip of the 31st bit would cause the expected variable to go negative, which would then try to read a huge amount of data. Also sanity check that the expected amount of data is large enough for the TPM header. Signed-off-by: Jeremy Boone <jeremy.boone(a)nccgroup.trust> Cc: stable(a)vger.kernel.org Signed-off-by: James Bottomley <James.Bottomley(a)HansenPartnership.com> Tested-by: Jarkko Sakkinen <jarkko.sakkinen(a)linux.intel.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen(a)linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen(a)linux.intel.com> Signed-off-by: James Morris <james.morris(a)microsoft.com> diff --git a/drivers/char/tpm/tpm_tis_core.c b/drivers/char/tpm/tpm_tis_core.c index 183a5f54d875..da074e3db19b 100644 --- a/drivers/char/tpm/tpm_tis_core.c +++ b/drivers/char/tpm/tpm_tis_core.c @@ -270,7 +270,8 @@ static int tpm_tis_recv(struct tpm_chip *chip, u8 *buf, size_t count) { struct tpm_tis_data *priv = dev_get_drvdata(&chip->dev); int size = 0; - int expected, status; + int status; + u32 expected; if (count < TPM_HEADER_SIZE) { size = -EIO; @@ -285,7 +286,7 @@ static int tpm_tis_recv(struct tpm_chip *chip, u8 *buf, size_t count) } expected = be32_to_cpu(*(__be32 *) (buf + 2)); - if (expected > count) { + if (expected > count || expected < TPM_HEADER_SIZE) { size = -EIO; goto out; }

7 years, 4 months

1
0
0 0

FAILED: patch "[PATCH] tpm: fix potential buffer overruns caused by bit glitches on" failed to apply to 4.4-stable tree

by gregkh＠linuxfoundation.org

The patch below does not apply to the 4.4-stable tree. If someone wants it applied there, or to any other stable or longterm tree, then please email the backport, including the original git commit id to <stable(a)vger.kernel.org>. thanks, greg k-h ------------------ original commit in Linus's tree ------------------ >From 3be23274755ee85771270a23af7691dc9b3a95db Mon Sep 17 00:00:00 2001 From: Jeremy Boone <jeremy.boone(a)nccgroup.trust> Date: Thu, 8 Feb 2018 12:28:08 -0800 Subject: [PATCH] tpm: fix potential buffer overruns caused by bit glitches on the bus Discrete TPMs are often connected over slow serial buses which, on some platforms, can have glitches causing bit flips. If a bit does flip it could cause an overrun if it's in one of the size parameters, so sanity check that we're not overrunning the provided buffer when doing a memcpy(). Signed-off-by: Jeremy Boone <jeremy.boone(a)nccgroup.trust> Cc: stable(a)vger.kernel.org Signed-off-by: James Bottomley <James.Bottomley(a)HansenPartnership.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen(a)linux.intel.com> Tested-by: Jarkko Sakkinen <jarkko.sakkinen(a)linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen(a)linux.intel.com> Signed-off-by: James Morris <james.morris(a)microsoft.com> diff --git a/drivers/char/tpm/tpm-interface.c b/drivers/char/tpm/tpm-interface.c index 76df4fbcf089..9e80a953d693 100644 --- a/drivers/char/tpm/tpm-interface.c +++ b/drivers/char/tpm/tpm-interface.c @@ -1190,6 +1190,10 @@ int tpm_get_random(struct tpm_chip *chip, u8 *out, size_t max) break; recd = be32_to_cpu(tpm_cmd.params.getrandom_out.rng_data_len); + if (recd > num_bytes) { + total = -EFAULT; + break; + } rlength = be32_to_cpu(tpm_cmd.header.out.length); if (rlength < offsetof(struct tpm_getrandom_out, rng_data) + diff --git a/drivers/char/tpm/tpm2-cmd.c b/drivers/char/tpm/tpm2-cmd.c index c17e75348a99..a700f8f9ead7 100644 --- a/drivers/char/tpm/tpm2-cmd.c +++ b/drivers/char/tpm/tpm2-cmd.c @@ -683,6 +683,10 @@ static int tpm2_unseal_cmd(struct tpm_chip *chip, if (!rc) { data_len = be16_to_cpup( (__be16 *) &buf.data[TPM_HEADER_SIZE + 4]); + if (data_len < MIN_KEY_SIZE || data_len > MAX_KEY_SIZE + 1) { + rc = -EFAULT; + goto out; + } rlength = be32_to_cpu(((struct tpm2_cmd *)&buf) ->header.out.length);

7 years, 4 months

1
0
0 0

FAILED: patch "[PATCH] tpm: fix potential buffer overruns caused by bit glitches on" failed to apply to 4.9-stable tree

by gregkh＠linuxfoundation.org

The patch below does not apply to the 4.9-stable tree. If someone wants it applied there, or to any other stable or longterm tree, then please email the backport, including the original git commit id to <stable(a)vger.kernel.org>. thanks, greg k-h ------------------ original commit in Linus's tree ------------------ >From 3be23274755ee85771270a23af7691dc9b3a95db Mon Sep 17 00:00:00 2001 From: Jeremy Boone <jeremy.boone(a)nccgroup.trust> Date: Thu, 8 Feb 2018 12:28:08 -0800 Subject: [PATCH] tpm: fix potential buffer overruns caused by bit glitches on the bus Discrete TPMs are often connected over slow serial buses which, on some platforms, can have glitches causing bit flips. If a bit does flip it could cause an overrun if it's in one of the size parameters, so sanity check that we're not overrunning the provided buffer when doing a memcpy(). Signed-off-by: Jeremy Boone <jeremy.boone(a)nccgroup.trust> Cc: stable(a)vger.kernel.org Signed-off-by: James Bottomley <James.Bottomley(a)HansenPartnership.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen(a)linux.intel.com> Tested-by: Jarkko Sakkinen <jarkko.sakkinen(a)linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen(a)linux.intel.com> Signed-off-by: James Morris <james.morris(a)microsoft.com> diff --git a/drivers/char/tpm/tpm-interface.c b/drivers/char/tpm/tpm-interface.c index 76df4fbcf089..9e80a953d693 100644 --- a/drivers/char/tpm/tpm-interface.c +++ b/drivers/char/tpm/tpm-interface.c @@ -1190,6 +1190,10 @@ int tpm_get_random(struct tpm_chip *chip, u8 *out, size_t max) break; recd = be32_to_cpu(tpm_cmd.params.getrandom_out.rng_data_len); + if (recd > num_bytes) { + total = -EFAULT; + break; + } rlength = be32_to_cpu(tpm_cmd.header.out.length); if (rlength < offsetof(struct tpm_getrandom_out, rng_data) + diff --git a/drivers/char/tpm/tpm2-cmd.c b/drivers/char/tpm/tpm2-cmd.c index c17e75348a99..a700f8f9ead7 100644 --- a/drivers/char/tpm/tpm2-cmd.c +++ b/drivers/char/tpm/tpm2-cmd.c @@ -683,6 +683,10 @@ static int tpm2_unseal_cmd(struct tpm_chip *chip, if (!rc) { data_len = be16_to_cpup( (__be16 *) &buf.data[TPM_HEADER_SIZE + 4]); + if (data_len < MIN_KEY_SIZE || data_len > MAX_KEY_SIZE + 1) { + rc = -EFAULT; + goto out; + } rlength = be32_to_cpu(((struct tpm2_cmd *)&buf) ->header.out.length);

7 years, 4 months

1
0
0 0

FAILED: patch "[PATCH] ixgbe: fix crash in build_skb Rx code path" failed to apply to 3.18-stable tree

by gregkh＠linuxfoundation.org

The patch below does not apply to the 3.18-stable tree. If someone wants it applied there, or to any other stable or longterm tree, then please email the backport, including the original git commit id to <stable(a)vger.kernel.org>. thanks, greg k-h ------------------ original commit in Linus's tree ------------------ >From 0c5661ecc5dd7ce296870a3eb7b62b1b280a5e89 Mon Sep 17 00:00:00 2001 From: Emil Tantilov <emil.s.tantilov(a)intel.com> Date: Fri, 23 Feb 2018 12:39:41 -0800 Subject: [PATCH] ixgbe: fix crash in build_skb Rx code path Add check for build_skb enabled ring in ixgbe_dma_sync_frag(). In that case &skb_shinfo(skb)->frags[0] may not always be set which can lead to a crash. Instead we derive the page offset from skb->data. Fixes: 42073d91a214 ("ixgbe: Have the CPU take ownership of the buffers sooner") CC: stable <stable(a)vger.kernel.org> Reported-by: Ambarish Soman <asoman(a)redhat.com> Suggested-by: Alexander Duyck <alexander.h.duyck(a)intel.com> Signed-off-by: Emil Tantilov <emil.s.tantilov(a)intel.com> Tested-by: Andrew Bowers <andrewx.bowers(a)intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher(a)intel.com> Signed-off-by: David S. Miller <davem(a)davemloft.net> diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c index 0da5aa2c8aba..9fc063af233c 100644 --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c @@ -1888,6 +1888,14 @@ static void ixgbe_dma_sync_frag(struct ixgbe_ring *rx_ring, ixgbe_rx_pg_size(rx_ring), DMA_FROM_DEVICE, IXGBE_RX_DMA_ATTR); + } else if (ring_uses_build_skb(rx_ring)) { + unsigned long offset = (unsigned long)(skb->data) & ~PAGE_MASK; + + dma_sync_single_range_for_cpu(rx_ring->dev, + IXGBE_CB(skb)->dma, + offset, + skb_headlen(skb), + DMA_FROM_DEVICE); } else { struct skb_frag_struct *frag = &skb_shinfo(skb)->frags[0];

7 years, 4 months

1
0
0 0

FAILED: patch "[PATCH] ixgbe: fix crash in build_skb Rx code path" failed to apply to 4.4-stable tree

by gregkh＠linuxfoundation.org

The patch below does not apply to the 4.4-stable tree. If someone wants it applied there, or to any other stable or longterm tree, then please email the backport, including the original git commit id to <stable(a)vger.kernel.org>. thanks, greg k-h ------------------ original commit in Linus's tree ------------------ >From 0c5661ecc5dd7ce296870a3eb7b62b1b280a5e89 Mon Sep 17 00:00:00 2001 From: Emil Tantilov <emil.s.tantilov(a)intel.com> Date: Fri, 23 Feb 2018 12:39:41 -0800 Subject: [PATCH] ixgbe: fix crash in build_skb Rx code path Add check for build_skb enabled ring in ixgbe_dma_sync_frag(). In that case &skb_shinfo(skb)->frags[0] may not always be set which can lead to a crash. Instead we derive the page offset from skb->data. Fixes: 42073d91a214 ("ixgbe: Have the CPU take ownership of the buffers sooner") CC: stable <stable(a)vger.kernel.org> Reported-by: Ambarish Soman <asoman(a)redhat.com> Suggested-by: Alexander Duyck <alexander.h.duyck(a)intel.com> Signed-off-by: Emil Tantilov <emil.s.tantilov(a)intel.com> Tested-by: Andrew Bowers <andrewx.bowers(a)intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher(a)intel.com> Signed-off-by: David S. Miller <davem(a)davemloft.net> diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c index 0da5aa2c8aba..9fc063af233c 100644 --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c @@ -1888,6 +1888,14 @@ static void ixgbe_dma_sync_frag(struct ixgbe_ring *rx_ring, ixgbe_rx_pg_size(rx_ring), DMA_FROM_DEVICE, IXGBE_RX_DMA_ATTR); + } else if (ring_uses_build_skb(rx_ring)) { + unsigned long offset = (unsigned long)(skb->data) & ~PAGE_MASK; + + dma_sync_single_range_for_cpu(rx_ring->dev, + IXGBE_CB(skb)->dma, + offset, + skb_headlen(skb), + DMA_FROM_DEVICE); } else { struct skb_frag_struct *frag = &skb_shinfo(skb)->frags[0];

7 years, 4 months

1
0
0 0

FAILED: patch "[PATCH] ixgbe: fix crash in build_skb Rx code path" failed to apply to 4.9-stable tree

by gregkh＠linuxfoundation.org

The patch below does not apply to the 4.9-stable tree. If someone wants it applied there, or to any other stable or longterm tree, then please email the backport, including the original git commit id to <stable(a)vger.kernel.org>. thanks, greg k-h ------------------ original commit in Linus's tree ------------------ >From 0c5661ecc5dd7ce296870a3eb7b62b1b280a5e89 Mon Sep 17 00:00:00 2001 From: Emil Tantilov <emil.s.tantilov(a)intel.com> Date: Fri, 23 Feb 2018 12:39:41 -0800 Subject: [PATCH] ixgbe: fix crash in build_skb Rx code path Add check for build_skb enabled ring in ixgbe_dma_sync_frag(). In that case &skb_shinfo(skb)->frags[0] may not always be set which can lead to a crash. Instead we derive the page offset from skb->data. Fixes: 42073d91a214 ("ixgbe: Have the CPU take ownership of the buffers sooner") CC: stable <stable(a)vger.kernel.org> Reported-by: Ambarish Soman <asoman(a)redhat.com> Suggested-by: Alexander Duyck <alexander.h.duyck(a)intel.com> Signed-off-by: Emil Tantilov <emil.s.tantilov(a)intel.com> Tested-by: Andrew Bowers <andrewx.bowers(a)intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher(a)intel.com> Signed-off-by: David S. Miller <davem(a)davemloft.net> diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c index 0da5aa2c8aba..9fc063af233c 100644 --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c @@ -1888,6 +1888,14 @@ static void ixgbe_dma_sync_frag(struct ixgbe_ring *rx_ring, ixgbe_rx_pg_size(rx_ring), DMA_FROM_DEVICE, IXGBE_RX_DMA_ATTR); + } else if (ring_uses_build_skb(rx_ring)) { + unsigned long offset = (unsigned long)(skb->data) & ~PAGE_MASK; + + dma_sync_single_range_for_cpu(rx_ring->dev, + IXGBE_CB(skb)->dma, + offset, + skb_headlen(skb), + DMA_FROM_DEVICE); } else { struct skb_frag_struct *frag = &skb_shinfo(skb)->frags[0];

7 years, 4 months

1
0
0 0

Patch "Bluetooth: btusb: Use DMI matching for QCA reset_resume quirking" has been added to the 4.9-stable tree

by gregkh＠linuxfoundation.org

This is a note to let you know that I've just added the patch titled Bluetooth: btusb: Use DMI matching for QCA reset_resume quirking to the 4.9-stable tree which can be found at: http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=sum… The filename of the patch is: bluetooth-btusb-use-dmi-matching-for-qca-reset_resume-quirking.patch and it can be found in the queue-4.9 subdirectory. If you, or anyone else, feels it should not be added to the stable tree, please let <stable(a)vger.kernel.org> know about it. >From 1fdb926974695d3dbc05a429bafa266fdd16510e Mon Sep 17 00:00:00 2001 From: Hans de Goede <hdegoede(a)redhat.com> Date: Tue, 20 Feb 2018 09:06:18 +0100 Subject: Bluetooth: btusb: Use DMI matching for QCA reset_resume quirking From: Hans de Goede <hdegoede(a)redhat.com> commit 1fdb926974695d3dbc05a429bafa266fdd16510e upstream. Commit 61f5acea8737 ("Bluetooth: btusb: Restore QCA Rome suspend/resume fix with a "rewritten" version") applied the USB_QUIRK_RESET_RESUME to all QCA USB Bluetooth modules. But it turns out that the resume problems are not caused by the QCA Rome chipset, on most platforms it resumes fine. The resume problems are actually a platform problem (likely the platform cutting all power when suspended). The USB_QUIRK_RESET_RESUME quirk also disables runtime suspend, so by matching on usb-ids, we're causing all boards with these chips to use extra power, to fix resume problems which only happen on some boards. This commit fixes this by applying the quirk based on DMI matching instead of on usb-ids, so that we match the platform and not the chipset. Here is the /sys/kernel/debug/usb/devices for the Bluetooth module: T: Bus=01 Lev=01 Prnt=01 Port=07 Cnt=04 Dev#= 5 Spd=12 MxCh= 0 D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cf3 ProdID=e300 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1514836 Fixes: 61f5acea8737 ("Bluetooth: btusb: Restore QCA Rome suspend/resume..") Cc: stable(a)vger.kernel.org Cc: Brian Norris <briannorris(a)chromium.org> Cc: Kai-Heng Feng <kai.heng.feng(a)canonical.com> Reported-and-tested-by: Kevin Fenzi <kevin(a)scrye.com> Signed-off-by: Hans de Goede <hdegoede(a)redhat.com> Signed-off-by: Marcel Holtmann <marcel(a)holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh(a)linuxfoundation.org> --- drivers/bluetooth/btusb.c | 25 +++++++++++++++++++------ 1 file changed, 19 insertions(+), 6 deletions(-) --- a/drivers/bluetooth/btusb.c +++ b/drivers/bluetooth/btusb.c @@ -21,6 +21,7 @@ * */ +#include <linux/dmi.h> #include <linux/module.h> #include <linux/usb.h> #include <linux/usb/quirks.h> @@ -358,6 +359,21 @@ static const struct usb_device_id blackl { } /* Terminating entry */ }; +/* The Bluetooth USB module build into some devices needs to be reset on resume, + * this is a problem with the platform (likely shutting off all power) not with + * the module itself. So we use a DMI list to match known broken platforms. + */ +static const struct dmi_system_id btusb_needs_reset_resume_table[] = { + { + /* Lenovo Yoga 920 (QCA Rome device 0cf3:e300) */ + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"), + DMI_MATCH(DMI_PRODUCT_VERSION, "Lenovo YOGA 920"), + }, + }, + {} +}; + #define BTUSB_MAX_ISOC_FRAMES 10 #define BTUSB_INTR_RUNNING 0 @@ -2926,12 +2942,6 @@ static int btusb_probe(struct usb_interf if (id->driver_info & BTUSB_QCA_ROME) { data->setup_on_usb = btusb_setup_qca; hdev->set_bdaddr = btusb_set_bdaddr_ath3012; - - /* QCA Rome devices lose their updated firmware over suspend, - * but the USB hub doesn't notice any status change. - * explicitly request a device reset on resume. - */ - interface_to_usbdev(intf)->quirks |= USB_QUIRK_RESET_RESUME; } #ifdef CONFIG_BT_HCIBTUSB_RTL @@ -3074,6 +3084,9 @@ static void btusb_disconnect(struct usb_ hci_free_dev(hdev); } + if (dmi_check_system(btusb_needs_reset_resume_table)) + interface_to_usbdev(intf)->quirks |= USB_QUIRK_RESET_RESUME; + #ifdef CONFIG_PM static int btusb_suspend(struct usb_interface *intf, pm_message_t message) { Patches currently in stable-queue which might be from hdegoede(a)redhat.com are queue-4.9/bluetooth-btusb-use-dmi-matching-for-qca-reset_resume-quirking.patch

7 years, 4 months

1
0
0 0

Patch "Bluetooth: btusb: Use DMI matching for QCA reset_resume quirking" has been added to the 4.15-stable tree

by gregkh＠linuxfoundation.org

This is a note to let you know that I've just added the patch titled Bluetooth: btusb: Use DMI matching for QCA reset_resume quirking to the 4.15-stable tree which can be found at: http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=sum… The filename of the patch is: bluetooth-btusb-use-dmi-matching-for-qca-reset_resume-quirking.patch and it can be found in the queue-4.15 subdirectory. If you, or anyone else, feels it should not be added to the stable tree, please let <stable(a)vger.kernel.org> know about it. >From 1fdb926974695d3dbc05a429bafa266fdd16510e Mon Sep 17 00:00:00 2001 From: Hans de Goede <hdegoede(a)redhat.com> Date: Tue, 20 Feb 2018 09:06:18 +0100 Subject: Bluetooth: btusb: Use DMI matching for QCA reset_resume quirking From: Hans de Goede <hdegoede(a)redhat.com> commit 1fdb926974695d3dbc05a429bafa266fdd16510e upstream. Commit 61f5acea8737 ("Bluetooth: btusb: Restore QCA Rome suspend/resume fix with a "rewritten" version") applied the USB_QUIRK_RESET_RESUME to all QCA USB Bluetooth modules. But it turns out that the resume problems are not caused by the QCA Rome chipset, on most platforms it resumes fine. The resume problems are actually a platform problem (likely the platform cutting all power when suspended). The USB_QUIRK_RESET_RESUME quirk also disables runtime suspend, so by matching on usb-ids, we're causing all boards with these chips to use extra power, to fix resume problems which only happen on some boards. This commit fixes this by applying the quirk based on DMI matching instead of on usb-ids, so that we match the platform and not the chipset. Here is the /sys/kernel/debug/usb/devices for the Bluetooth module: T: Bus=01 Lev=01 Prnt=01 Port=07 Cnt=04 Dev#= 5 Spd=12 MxCh= 0 D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cf3 ProdID=e300 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1514836 Fixes: 61f5acea8737 ("Bluetooth: btusb: Restore QCA Rome suspend/resume..") Cc: stable(a)vger.kernel.org Cc: Brian Norris <briannorris(a)chromium.org> Cc: Kai-Heng Feng <kai.heng.feng(a)canonical.com> Reported-and-tested-by: Kevin Fenzi <kevin(a)scrye.com> Signed-off-by: Hans de Goede <hdegoede(a)redhat.com> Signed-off-by: Marcel Holtmann <marcel(a)holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh(a)linuxfoundation.org> --- drivers/bluetooth/btusb.c | 25 +++++++++++++++++++------ 1 file changed, 19 insertions(+), 6 deletions(-) --- a/drivers/bluetooth/btusb.c +++ b/drivers/bluetooth/btusb.c @@ -21,6 +21,7 @@ * */ +#include <linux/dmi.h> #include <linux/module.h> #include <linux/usb.h> #include <linux/usb/quirks.h> @@ -376,6 +377,21 @@ static const struct usb_device_id blackl { } /* Terminating entry */ }; +/* The Bluetooth USB module build into some devices needs to be reset on resume, + * this is a problem with the platform (likely shutting off all power) not with + * the module itself. So we use a DMI list to match known broken platforms. + */ +static const struct dmi_system_id btusb_needs_reset_resume_table[] = { + { + /* Lenovo Yoga 920 (QCA Rome device 0cf3:e300) */ + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"), + DMI_MATCH(DMI_PRODUCT_VERSION, "Lenovo YOGA 920"), + }, + }, + {} +}; + #define BTUSB_MAX_ISOC_FRAMES 10 #define BTUSB_INTR_RUNNING 0 @@ -3031,6 +3047,9 @@ static int btusb_probe(struct usb_interf hdev->send = btusb_send_frame; hdev->notify = btusb_notify; + if (dmi_check_system(btusb_needs_reset_resume_table)) + interface_to_usbdev(intf)->quirks |= USB_QUIRK_RESET_RESUME; + #ifdef CONFIG_PM err = btusb_config_oob_wake(hdev); if (err) @@ -3117,12 +3136,6 @@ static int btusb_probe(struct usb_interf if (id->driver_info & BTUSB_QCA_ROME) { data->setup_on_usb = btusb_setup_qca; hdev->set_bdaddr = btusb_set_bdaddr_ath3012; - - /* QCA Rome devices lose their updated firmware over suspend, - * but the USB hub doesn't notice any status change. - * explicitly request a device reset on resume. - */ - interface_to_usbdev(intf)->quirks |= USB_QUIRK_RESET_RESUME; } #ifdef CONFIG_BT_HCIBTUSB_RTL Patches currently in stable-queue which might be from hdegoede(a)redhat.com are queue-4.15/bluetooth-btusb-use-dmi-matching-for-qca-reset_resume-quirking.patch

7 years, 4 months

1
0
0 0

Patch "Bluetooth: btusb: Use DMI matching for QCA reset_resume quirking" has been added to the 4.14-stable tree

by gregkh＠linuxfoundation.org

This is a note to let you know that I've just added the patch titled Bluetooth: btusb: Use DMI matching for QCA reset_resume quirking to the 4.14-stable tree which can be found at: http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=sum… The filename of the patch is: bluetooth-btusb-use-dmi-matching-for-qca-reset_resume-quirking.patch and it can be found in the queue-4.14 subdirectory. If you, or anyone else, feels it should not be added to the stable tree, please let <stable(a)vger.kernel.org> know about it. >From 1fdb926974695d3dbc05a429bafa266fdd16510e Mon Sep 17 00:00:00 2001 From: Hans de Goede <hdegoede(a)redhat.com> Date: Tue, 20 Feb 2018 09:06:18 +0100 Subject: Bluetooth: btusb: Use DMI matching for QCA reset_resume quirking From: Hans de Goede <hdegoede(a)redhat.com> commit 1fdb926974695d3dbc05a429bafa266fdd16510e upstream. Commit 61f5acea8737 ("Bluetooth: btusb: Restore QCA Rome suspend/resume fix with a "rewritten" version") applied the USB_QUIRK_RESET_RESUME to all QCA USB Bluetooth modules. But it turns out that the resume problems are not caused by the QCA Rome chipset, on most platforms it resumes fine. The resume problems are actually a platform problem (likely the platform cutting all power when suspended). The USB_QUIRK_RESET_RESUME quirk also disables runtime suspend, so by matching on usb-ids, we're causing all boards with these chips to use extra power, to fix resume problems which only happen on some boards. This commit fixes this by applying the quirk based on DMI matching instead of on usb-ids, so that we match the platform and not the chipset. Here is the /sys/kernel/debug/usb/devices for the Bluetooth module: T: Bus=01 Lev=01 Prnt=01 Port=07 Cnt=04 Dev#= 5 Spd=12 MxCh= 0 D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cf3 ProdID=e300 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1514836 Fixes: 61f5acea8737 ("Bluetooth: btusb: Restore QCA Rome suspend/resume..") Cc: stable(a)vger.kernel.org Cc: Brian Norris <briannorris(a)chromium.org> Cc: Kai-Heng Feng <kai.heng.feng(a)canonical.com> Reported-and-tested-by: Kevin Fenzi <kevin(a)scrye.com> Signed-off-by: Hans de Goede <hdegoede(a)redhat.com> Signed-off-by: Marcel Holtmann <marcel(a)holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh(a)linuxfoundation.org> --- drivers/bluetooth/btusb.c | 25 +++++++++++++++++++------ 1 file changed, 19 insertions(+), 6 deletions(-) --- a/drivers/bluetooth/btusb.c +++ b/drivers/bluetooth/btusb.c @@ -21,6 +21,7 @@ * */ +#include <linux/dmi.h> #include <linux/module.h> #include <linux/usb.h> #include <linux/usb/quirks.h> @@ -381,6 +382,21 @@ static const struct usb_device_id blackl { } /* Terminating entry */ }; +/* The Bluetooth USB module build into some devices needs to be reset on resume, + * this is a problem with the platform (likely shutting off all power) not with + * the module itself. So we use a DMI list to match known broken platforms. + */ +static const struct dmi_system_id btusb_needs_reset_resume_table[] = { + { + /* Lenovo Yoga 920 (QCA Rome device 0cf3:e300) */ + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"), + DMI_MATCH(DMI_PRODUCT_VERSION, "Lenovo YOGA 920"), + }, + }, + {} +}; + #define BTUSB_MAX_ISOC_FRAMES 10 #define BTUSB_INTR_RUNNING 0 @@ -3013,6 +3029,9 @@ static int btusb_probe(struct usb_interf hdev->send = btusb_send_frame; hdev->notify = btusb_notify; + if (dmi_check_system(btusb_needs_reset_resume_table)) + interface_to_usbdev(intf)->quirks |= USB_QUIRK_RESET_RESUME; + #ifdef CONFIG_PM err = btusb_config_oob_wake(hdev); if (err) @@ -3099,12 +3118,6 @@ static int btusb_probe(struct usb_interf if (id->driver_info & BTUSB_QCA_ROME) { data->setup_on_usb = btusb_setup_qca; hdev->set_bdaddr = btusb_set_bdaddr_ath3012; - - /* QCA Rome devices lose their updated firmware over suspend, - * but the USB hub doesn't notice any status change. - * explicitly request a device reset on resume. - */ - interface_to_usbdev(intf)->quirks |= USB_QUIRK_RESET_RESUME; } #ifdef CONFIG_BT_HCIBTUSB_RTL Patches currently in stable-queue which might be from hdegoede(a)redhat.com are queue-4.14/bluetooth-btusb-use-dmi-matching-for-qca-reset_resume-quirking.patch

7 years, 4 months

1
0
0 0

patch "Drivers: hv: vmbus: Fix ring buffer signaling" added to char-misc-linus

by gregkh＠linuxfoundation.org

This is a note to let you know that I've just added the patch titled Drivers: hv: vmbus: Fix ring buffer signaling to my char-misc git tree which can be found at git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc.git in the char-misc-linus branch. The patch will show up in the next release of the linux-next tree (usually sometime within the next 24 hours during the week.) The patch will hopefully also be merged in Linus's tree for the next -rc kernel release. If you have any questions about this process, please let me know. >From 655296c8bbeffcf020558c4455305d597a73bde1 Mon Sep 17 00:00:00 2001 From: Michael Kelley <mhkelley(a)outlook.com> Date: Sun, 4 Mar 2018 22:24:08 -0700 Subject: Drivers: hv: vmbus: Fix ring buffer signaling Fix bugs in signaling the Hyper-V host when freeing space in the host->guest ring buffer: 1. The interrupt_mask must not be used to determine whether to signal on the host->guest ring buffer 2. The ring buffer write_index must be read (via hv_get_bytes_to_write) *after* pending_send_sz is read in order to avoid a race condition 3. Comparisons with pending_send_sz must treat the "equals" case as not-enough-space 4. Don't signal if the pending_send_sz feature is not present. Older versions of Hyper-V that don't implement this feature will poll. Fixes: 03bad714a161 ("vmbus: more host signalling avoidance") Cc: Stable <stable(a)vger.kernel.org> # 4.14 and above Signed-off-by: Michael Kelley <mhkelley(a)outlook.com> Signed-off-by: K. Y. Srinivasan <kys(a)microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh(a)linuxfoundation.org> --- drivers/hv/ring_buffer.c | 52 ++++++++++++++++++++++++++++++++---------------- 1 file changed, 35 insertions(+), 17 deletions(-) diff --git a/drivers/hv/ring_buffer.c b/drivers/hv/ring_buffer.c index 50e071444a5c..8699bb969e7e 100644 --- a/drivers/hv/ring_buffer.c +++ b/drivers/hv/ring_buffer.c @@ -417,13 +417,24 @@ __hv_pkt_iter_next(struct vmbus_channel *channel, } EXPORT_SYMBOL_GPL(__hv_pkt_iter_next); +/* How many bytes were read in this iterator cycle */ +static u32 hv_pkt_iter_bytes_read(const struct hv_ring_buffer_info *rbi, + u32 start_read_index) +{ + if (rbi->priv_read_index >= start_read_index) + return rbi->priv_read_index - start_read_index; + else + return rbi->ring_datasize - start_read_index + + rbi->priv_read_index; +} + /* * Update host ring buffer after iterating over packets. */ void hv_pkt_iter_close(struct vmbus_channel *channel) { struct hv_ring_buffer_info *rbi = &channel->inbound; - u32 orig_write_sz = hv_get_bytes_to_write(rbi); + u32 curr_write_sz, pending_sz, bytes_read, start_read_index; /* * Make sure all reads are done before we update the read index since @@ -431,8 +442,12 @@ void hv_pkt_iter_close(struct vmbus_channel *channel) * is updated. */ virt_rmb(); + start_read_index = rbi->ring_buffer->read_index; rbi->ring_buffer->read_index = rbi->priv_read_index; + if (!rbi->ring_buffer->feature_bits.feat_pending_send_sz) + return; + /* * Issue a full memory barrier before making the signaling decision. * Here is the reason for having this barrier: @@ -446,26 +461,29 @@ void hv_pkt_iter_close(struct vmbus_channel *channel) */ virt_mb(); - /* If host has disabled notifications then skip */ - if (rbi->ring_buffer->interrupt_mask) + pending_sz = READ_ONCE(rbi->ring_buffer->pending_send_sz); + if (!pending_sz) return; - if (rbi->ring_buffer->feature_bits.feat_pending_send_sz) { - u32 pending_sz = READ_ONCE(rbi->ring_buffer->pending_send_sz); + /* + * Ensure the read of write_index in hv_get_bytes_to_write() + * happens after the read of pending_send_sz. + */ + virt_rmb(); + curr_write_sz = hv_get_bytes_to_write(rbi); + bytes_read = hv_pkt_iter_bytes_read(rbi, start_read_index); - /* - * If there was space before we began iteration, - * then host was not blocked. Also handles case where - * pending_sz is zero then host has nothing pending - * and does not need to be signaled. - */ - if (orig_write_sz > pending_sz) - return; + /* + * If there was space before we began iteration, + * then host was not blocked. + */ - /* If pending write will not fit, don't give false hope. */ - if (hv_get_bytes_to_write(rbi) < pending_sz) - return; - } + if (curr_write_sz - bytes_read > pending_sz) + return; + + /* If pending write will not fit, don't give false hope. */ + if (curr_write_sz <= pending_sz) + return; vmbus_setevent(channel); } -- 2.16.2

7 years, 4 months

1
0
0 0

2025

2024

2023

2022

2021

2020

2019

2018

2017

Linux-stable-mirror