The QSPI peripheral control and status registers are
accessible via the SoC's APB bus, whereas MMIO transactions'
data travels on the AHB bus.
Microchip documentation and even sample code from Atmel
emphasises the need for a memory barrier before the first
MMIO transaction to the AHB-connected QSPI, and before the
last write to its registers via APB. This is achieved by
the following lines in `atmel_qspi_transfer()`:
/* Dummy read of QSPI_IFR to synchronize APB and AHB accesses */
(void)atmel_qspi_read(aq, QSPI_IFR);
However, the current documentation makes no mention to
synchronization requirements in the other direction, i.e.
after the last data written via AHB, and before the first
register access on APB.
In our case, we were facing an issue where the QSPI peripheral
would cease to send any new CSR (nCS Rise) interrupts,
leading to a timeout in `atmel_qspi_wait_for_completion()`
and ultimately this panic in higher levels:
ubi0 error: ubi_io_write: error -110 while writing 63108 bytes
to PEB 491:128, written 63104 bytes
After months of extensive research of the codebase, fiddling
around the debugger with kgdb, and back-and-forth with
Microchip, we came to the conclusion that the issue is
probably that the peripheral is still busy receiving on AHB
when the LASTXFER bit is written to its Control Register
on APB, therefore this write gets lost, and the peripheral
still thinks there is more data to come in the MMIO transfer.
This was first formulated when we noticed that doubling the
write() of QSPI_CR_LASTXFER seemed to solve the problem.
Ultimately, the solution is to introduce memory barriers
after the AHB-mapped MMIO transfers, to ensure ordering.
Fixes: d5433def3153 ("mtd: spi-nor: atmel-quadspi: Add spi-mem support to atmel-quadspi")
Cc: Hari.PrasathGE(a)microchip.com
Cc: Mahesh.Abotula(a)microchip.com
Cc: Marco.Cardellini(a)microchip.com
Cc: <stable(a)vger.kernel.org> # c0a0203cf579: ("spi: atmel-quadspi: Create `atmel_qspi_ops`"...)
Cc: <stable(a)vger.kernel.org> # 6.x.y
Signed-off-by: Bence Csókás <csokas.bence(a)prolan.hu>
---
Notes:
Changes in v2:
* dropping --- from commit msg
Resubmit: rebased on current spi-next
drivers/spi/atmel-quadspi.c | 11 +++++++++--
1 file changed, 9 insertions(+), 2 deletions(-)
diff --git a/drivers/spi/atmel-quadspi.c b/drivers/spi/atmel-quadspi.c
index f46da363574f..8fdc9d27a95e 100644
--- a/drivers/spi/atmel-quadspi.c
+++ b/drivers/spi/atmel-quadspi.c
@@ -661,13 +661,20 @@ static int atmel_qspi_transfer(struct spi_mem *mem,
(void)atmel_qspi_read(aq, QSPI_IFR);
/* Send/Receive data */
- if (op->data.dir == SPI_MEM_DATA_IN)
+ if (op->data.dir == SPI_MEM_DATA_IN) {
memcpy_fromio(op->data.buf.in, aq->mem + offset,
op->data.nbytes);
- else
+
+ /* Synchronize AHB and APB accesses again */
+ rmb();
+ } else {
memcpy_toio(aq->mem + offset, op->data.buf.out,
op->data.nbytes);
+ /* Synchronize AHB and APB accesses again */
+ wmb();
+ }
+
/* Release the chip-select */
atmel_qspi_write(QSPI_CR_LASTXFER, aq, QSPI_CR);
--
2.34.1
Recent changes in the clock tree have set CLK_SET_RATE_PARENT to the two
LCDIF pixel clocks. The idea is, instead of using assigned-clock
properties to set upstream PLL rates to high frequencies and hoping that
a single divisor (namely media_disp[12]_pix) will be close enough in
most cases, we should tell the clock core to use the PLL to properly
derive an accurate pixel clock rate in the first place. Here is the
situation.
[Before ff06ea04e4cf ("clk: imx: clk-imx8mp: Allow media_disp pixel clock reconfigure parent rate")]
Before setting CLK_SET_RATE_PARENT to the media_disp[12]_pix clocks, the sequence of events was:
- PLL is assigned to a high rate,
- media_disp[12]_pix is set to approximately freq A by using a single divisor,
- media_ldb is set to approximately freq 7*A by using another single divisor.
=> The display was working, but the pixel clock was inaccurate.
[After ff06ea04e4cf ("clk: imx: clk-imx8mp: Allow media_disp pixel clock reconfigure parent rate")]
After setting CLK_SET_RATE_PARENT to the media_disp[12]_pix clocks, the
sequence of events became:
- media_disp[12]_pix is set to freq A by using a divisor of 1 and
setting video_pll1 to freq A.
- media_ldb is trying to compute its divisor to set freq 7*A, but the
upstream PLL is to low, it does not recompute it, so it ends up
setting a divisor of 1 and being at freq A instead of 7*A.
=> The display is sadly no longer working
[After applying PATCH "clk: imx: clk-imx8mp: Allow LDB serializer clock reconfigure parent rate"]
This is a commit from Marek, which is, I believe going in the right
direction, so I am including it. Just with this change, the situation is
slightly different, but the result is the same:
- media_disp[12]_pix is set to freq A by using a divisor of 1 and
setting video_pll1 to freq A.
- media_ldb is set to 7*A by using a divisor of 1 and setting video_pll1
to freq 7*A.
/!\ This as the side effect of changing media_disp[12]_pix from freq A
to freq 7*A.
=> The display is still not working
[After applying this series]
The goal of the following patches is to prevent clock subtree walks to
"just recalculate" the pixel clocks, ignoring the fact that they should
no longer change. They should adapt their divisors to the new upstream
rates instead. As a result, the display pipeline is working again.
Note: if more than one display is connected, we need the LDB driver to
act accordingly, thus the LDB driver must be adapted. Also, if accurate
pixel clocks are not possible with two different displays, we will still
need (at least for now) to make sure one of them is reparented to
another PLL, like the audio PLL (but audio PLL are of a different kind,
and are slightly less accurate).
So this series aims at fixing the i.MX8MP display pipeline for simple
setups. Said otherwise, returning to the same level of support as
before, but with (hopefully) more accurate frequencies. I believe this
approach manages to fix both Marek situation and all people using a
straightforward LCD based setup. For more complex setups, we need more
smartness from DRM and clk, but this is gonna take a bit of time.
---
Marek Vasut (1):
clk: imx: clk-imx8mp: Allow LDB serializer clock reconfigure parent rate
Miquel Raynal (4):
clk: Add a helper to determine a clock rate
clk: Split clk_calc_subtree()
clk: Add flag to prevent frequency changes when walking subtrees
clk: imx: imx8mp: Prevent media clocks to be incompatibly changed
drivers/clk/clk.c | 39 ++++++++++++++++++++++++++++++++-------
drivers/clk/imx/clk-imx8mp.c | 6 +++---
include/linux/clk-provider.h | 2 ++
3 files changed, 37 insertions(+), 10 deletions(-)
---
base-commit: 62facaf164585923d081eedcb6871f4ff3c2e953
change-id: 20241121-ge-ian-debug-imx8-clk-tree-bd325aa866f1
Best regards,
--
Miquel Raynal <miquel.raynal(a)bootlin.com>
Hi Sasha,
+ cc stable(a)vger.kernel.org
On Fri, 3 Jan 2025 at 00:45, Sasha Levin <sashal(a)kernel.org> wrote:
>
> This is a note to let you know that I've just added the patch titled
>
> watchdog: s3c2410_wdt: use exynos_get_pmu_regmap_by_phandle() for PMU regs
>
> to the 6.6-stable tree which can be found at:
> http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=sum…
>
> The filename of the patch is:
> watchdog-s3c2410_wdt-use-exynos_get_pmu_regmap_by_ph.patch
> and it can be found in the queue-6.6 subdirectory.
>
> If you, or anyone else, feels it should not be added to the stable tree,
> please let <stable(a)vger.kernel.org> know about it.
It doesn't make sense (to me at least) to add this patch and then also
add the revert of it to v6.6 stable tree, as it becomes a no-op. The
only reason I can think of is it somehow helps with your automated
tooling?
Additionally the hardware (Pixel 6 & gs101 SoC ) which these patches
and APIs were added for wasn't merged until v6.8. The revert is also
only applicable if the kernel has the corresponding enhancements made
to syscon driver to register custom regmaps. See 769cb63166d9 ("mfd:
syscon: Add of_syscon_register_regmap() API")
Thanks,
Peter
On Mon, Jan 06, 2025 at 11:41:20AM +0100, gregkh(a)linuxfoundation.org wrote:
>
> This is a note to let you know that I've just added the patch titled
>
> vmstat: disable vmstat_work on vmstat_cpu_down_prep()
>
> to the 6.12-stable tree which can be found at:
> http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=sum…
>
> The filename of the patch is:
> vmstat-disable-vmstat_work-on-vmstat_cpu_down_prep.patch
> and it can be found in the queue-6.12 subdirectory.
>
> If you, or anyone else, feels it should not be added to the stable tree,
> please let <stable(a)vger.kernel.org> know about it.
Hi, could you hold off on adding this for now? It's broken [1] and needs to
be fixed. Once a follow-up fix is ready, I'll make sure to notify you.
[1] https://lore.kernel.org/linux-mm/7ed97096-859e-46d0-8f27-16a2298a8914@lucif…
Thanks.
-Koichiro Den
>
>
> From adcfb264c3ed51fbbf5068ddf10d309a63683868 Mon Sep 17 00:00:00 2001
> From: Koichiro Den <koichiro.den(a)canonical.com>
> Date: Sat, 21 Dec 2024 12:33:20 +0900
> Subject: vmstat: disable vmstat_work on vmstat_cpu_down_prep()
>
> From: Koichiro Den <koichiro.den(a)canonical.com>
>
> commit adcfb264c3ed51fbbf5068ddf10d309a63683868 upstream.
>
> Even after mm/vmstat:online teardown, shepherd may still queue work for
> the dying cpu until the cpu is removed from online mask. While it's quite
> rare, this means that after unbind_workers() unbinds a per-cpu kworker, it
> potentially runs vmstat_update for the dying CPU on an irrelevant cpu
> before entering atomic AP states. When CONFIG_DEBUG_PREEMPT=y, it results
> in the following error with the backtrace.
>
> BUG: using smp_processor_id() in preemptible [00000000] code: \
> kworker/7:3/1702
> caller is refresh_cpu_vm_stats+0x235/0x5f0
> CPU: 0 UID: 0 PID: 1702 Comm: kworker/7:3 Tainted: G
> Tainted: [N]=TEST
> Workqueue: mm_percpu_wq vmstat_update
> Call Trace:
> <TASK>
> dump_stack_lvl+0x8d/0xb0
> check_preemption_disabled+0xce/0xe0
> refresh_cpu_vm_stats+0x235/0x5f0
> vmstat_update+0x17/0xa0
> process_one_work+0x869/0x1aa0
> worker_thread+0x5e5/0x1100
> kthread+0x29e/0x380
> ret_from_fork+0x2d/0x70
> ret_from_fork_asm+0x1a/0x30
> </TASK>
>
> So, for mm/vmstat:online, disable vmstat_work reliably on teardown and
> symmetrically enable it on startup.
>
> Link: https://lkml.kernel.org/r/20241221033321.4154409-1-koichiro.den@canonical.c…
> Signed-off-by: Koichiro Den <koichiro.den(a)canonical.com>
> Cc: Sebastian Andrzej Siewior <bigeasy(a)linutronix.de>
> Cc: <stable(a)vger.kernel.org>
> Signed-off-by: Andrew Morton <akpm(a)linux-foundation.org>
> Signed-off-by: Greg Kroah-Hartman <gregkh(a)linuxfoundation.org>
> ---
> mm/vmstat.c | 3 ++-
> 1 file changed, 2 insertions(+), 1 deletion(-)
>
> --- a/mm/vmstat.c
> +++ b/mm/vmstat.c
> @@ -2139,13 +2139,14 @@ static int vmstat_cpu_online(unsigned in
> if (!node_state(cpu_to_node(cpu), N_CPU)) {
> node_set_state(cpu_to_node(cpu), N_CPU);
> }
> + enable_delayed_work(&per_cpu(vmstat_work, cpu));
>
> return 0;
> }
>
> static int vmstat_cpu_down_prep(unsigned int cpu)
> {
> - cancel_delayed_work_sync(&per_cpu(vmstat_work, cpu));
> + disable_delayed_work_sync(&per_cpu(vmstat_work, cpu));
> return 0;
> }
>
>
>
> Patches currently in stable-queue which might be from koichiro.den(a)canonical.com are
>
> queue-6.12/vmstat-disable-vmstat_work-on-vmstat_cpu_down_prep.patch
This partially reverts commit that made hfi_session_destroy()
the first step of vdec/venc close(). The reason being is a
regression report when, supposedly, encode/decoder is closed
with still active streaming (no ->stop_streaming() call before
close()) and pending pkts, so isr_thread cannot find instance
and fails to process those pending pkts. This was the idea
behind the original patch - make it impossible to use instance
under destruction, because this is racy, but apparently there
are uses cases that depend on that unsafe pattern. Return to
the old (unsafe) behaviour for the time being (until a better
fix is found).
Fixes: 45b1a1b348ec1 ("media: venus: sync with threaded IRQ during inst destruction")
Cc: stable(a)vger.kernel.org
Reported-by: Nathan Hebert <nhebert(a)google.com>
Signed-off-by: Sergey Senozhatsky <senozhatsky(a)chromium.org>
---
drivers/media/platform/qcom/venus/core.c | 8 ++------
1 file changed, 2 insertions(+), 6 deletions(-)
diff --git a/drivers/media/platform/qcom/venus/core.c b/drivers/media/platform/qcom/venus/core.c
index 2d27c5167246..807487a1f536 100644
--- a/drivers/media/platform/qcom/venus/core.c
+++ b/drivers/media/platform/qcom/venus/core.c
@@ -506,18 +506,14 @@ static __maybe_unused int venus_runtime_suspend(struct device *dev)
void venus_close_common(struct venus_inst *inst)
{
/*
- * First, remove the inst from the ->instances list, so that
- * to_instance() will return NULL.
- */
- hfi_session_destroy(inst);
- /*
- * Second, make sure we don't have IRQ/IRQ-thread currently running
+ * Make sure we don't have IRQ/IRQ-thread currently running
* or pending execution, which would race with the inst destruction.
*/
synchronize_irq(inst->core->irq);
v4l2_m2m_ctx_release(inst->m2m_ctx);
v4l2_m2m_release(inst->m2m_dev);
+ hfi_session_destroy(inst);
v4l2_fh_del(&inst->fh);
v4l2_fh_exit(&inst->fh);
v4l2_ctrl_handler_free(&inst->ctrl_handler);
--
2.47.1.613.gc27f4b7a9f-goog
Estimated people:
Seems to me, I browse drivers/acpi/resources.c: the patch was not included in kernel versions stable 6.12.7 or long term 6.6.68.
I hope will be include in mainline 6.13.-rc5 to inform if work in the ASUS Vivobook 15 X1504VAP_X1504VA keyboard.
I have not idea how work with git diff or compiling kernels to try the patch, and need to try in installed kernel.
Thanks.Regards.
Sent: Friday, December 20, 2024 at 8:23 PM
From: bugzilla-daemon(a)kernel.org
To: gazo11(a)mail.com
Subject: [Bug 219224] Laptop Internal Keyboard not working on ASUS VivoBook E1404GA on ubuntu 24.04.
https://bugzilla.kernel.org/show_bug.cgi?id=219224
--- Comment #11 from Hans de Goede (jwrdegoede(a)fedoraproject.org) ---
(In reply to gazo11 from comment #10)
> Hello I have the same problem for dmidecode:
>
>
> System Information
> Manufacturer: ASUSTeK COMPUTER INC.
> Product Name: ASUS Vivobook 15 X1504VAP_X1504VA
> Version: 1.0
> Serial Number: S1N0CV02L86302G
> UUID: cdc508f0-d3f1-f743-bce4-5eb9d4c06fda
> Wake-up Type: Power Switch
> SKU Number:
> Family: ASUS Vivobook 15
>
> Its possible to get this model listed in future kernels? Thanks!
Thank you for reporting this, I've submitted a patch to add this to the
irq1_level_low_skip_override[] list:
https://lore.kernel.org/linux-acpi/20241220181352.25974-1-hdegoede@redhat.c…
--
You may reply to this email to add a comment.
You are receiving this mail because:
You are on the CC list for the bug.
The patch below does not apply to the 6.6-stable tree.
If someone wants it applied there, or to any other stable or longterm
tree, then please email the backport, including the original git commit
id to <stable(a)vger.kernel.org>.
To reproduce the conflict and resubmit, you may use the following commands:
git fetch https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/ linux-6.6.y
git checkout FETCH_HEAD
git cherry-pick -x 8ec396d05d1b737c87311fb7311f753b02c2a6b1
# <resolve conflicts, build, test, etc.>
git commit -s
git send-email --to '<stable(a)vger.kernel.org>' --in-reply-to '2025010652-resemble-faceplate-702c@gregkh' --subject-prefix 'PATCH 6.6.y' HEAD^..
Possible dependencies:
thanks,
greg k-h
------------------ original commit in Linus's tree ------------------
From 8ec396d05d1b737c87311fb7311f753b02c2a6b1 Mon Sep 17 00:00:00 2001
From: Lorenzo Stoakes <lorenzo.stoakes(a)oracle.com>
Date: Thu, 28 Nov 2024 15:06:17 +0000
Subject: [PATCH] mm: reinstate ability to map write-sealed memfd mappings
read-only
Patch series "mm: reinstate ability to map write-sealed memfd mappings
read-only".
In commit 158978945f31 ("mm: perform the mapping_map_writable() check
after call_mmap()") (and preceding changes in the same series) it became
possible to mmap() F_SEAL_WRITE sealed memfd mappings read-only.
Commit 5de195060b2e ("mm: resolve faulty mmap_region() error path
behaviour") unintentionally undid this logic by moving the
mapping_map_writable() check before the shmem_mmap() hook is invoked,
thereby regressing this change.
This series reworks how we both permit write-sealed mappings being mapped
read-only and disallow mprotect() from undoing the write-seal, fixing this
regression.
We also add a regression test to ensure that we do not accidentally
regress this in future.
Thanks to Julian Orth for reporting this regression.
This patch (of 2):
In commit 158978945f31 ("mm: perform the mapping_map_writable() check
after call_mmap()") (and preceding changes in the same series) it became
possible to mmap() F_SEAL_WRITE sealed memfd mappings read-only.
This was previously unnecessarily disallowed, despite the man page
documentation indicating that it would be, thereby limiting the usefulness
of F_SEAL_WRITE logic.
We fixed this by adapting logic that existed for the F_SEAL_FUTURE_WRITE
seal (one which disallows future writes to the memfd) to also be used for
F_SEAL_WRITE.
For background - the F_SEAL_FUTURE_WRITE seal clears VM_MAYWRITE for a
read-only mapping to disallow mprotect() from overriding the seal - an
operation performed by seal_check_write(), invoked from shmem_mmap(), the
f_op->mmap() hook used by shmem mappings.
By extending this to F_SEAL_WRITE and critically - checking
mapping_map_writable() to determine if we may map the memfd AFTER we
invoke shmem_mmap() - the desired logic becomes possible. This is because
mapping_map_writable() explicitly checks for VM_MAYWRITE, which we will
have cleared.
Commit 5de195060b2e ("mm: resolve faulty mmap_region() error path
behaviour") unintentionally undid this logic by moving the
mapping_map_writable() check before the shmem_mmap() hook is invoked,
thereby regressing this change.
We reinstate this functionality by moving the check out of shmem_mmap()
and instead performing it in do_mmap() at the point at which VMA flags are
being determined, which seems in any case to be a more appropriate place
in which to make this determination.
In order to achieve this we rework memfd seal logic to allow us access to
this information using existing logic and eliminate the clearing of
VM_MAYWRITE from seal_check_write() which we are performing in do_mmap()
instead.
Link: https://lkml.kernel.org/r/99fc35d2c62bd2e05571cf60d9f8b843c56069e0.17328047…
Fixes: 5de195060b2e ("mm: resolve faulty mmap_region() error path behaviour")
Signed-off-by: Lorenzo Stoakes <lorenzo.stoakes(a)oracle.com>
Reported-by: Julian Orth <ju.orth(a)gmail.com>
Closes: https://lore.kernel.org/all/CAHijbEUMhvJTN9Xw1GmbM266FXXv=U7s4L_Jem5x3AaPZx…
Cc: Jann Horn <jannh(a)google.com>
Cc: Liam R. Howlett <Liam.Howlett(a)Oracle.com>
Cc: Linus Torvalds <torvalds(a)linux-foundation.org>
Cc: Shuah Khan <shuah(a)kernel.org>
Cc: Vlastimil Babka <vbabka(a)suse.cz>
Cc: <stable(a)vger.kernel.org>
Signed-off-by: Andrew Morton <akpm(a)linux-foundation.org>
diff --git a/include/linux/memfd.h b/include/linux/memfd.h
index 3f2cf339ceaf..d437e3070850 100644
--- a/include/linux/memfd.h
+++ b/include/linux/memfd.h
@@ -7,6 +7,7 @@
#ifdef CONFIG_MEMFD_CREATE
extern long memfd_fcntl(struct file *file, unsigned int cmd, unsigned int arg);
struct folio *memfd_alloc_folio(struct file *memfd, pgoff_t idx);
+unsigned int *memfd_file_seals_ptr(struct file *file);
#else
static inline long memfd_fcntl(struct file *f, unsigned int c, unsigned int a)
{
@@ -16,6 +17,19 @@ static inline struct folio *memfd_alloc_folio(struct file *memfd, pgoff_t idx)
{
return ERR_PTR(-EINVAL);
}
+
+static inline unsigned int *memfd_file_seals_ptr(struct file *file)
+{
+ return NULL;
+}
#endif
+/* Retrieve memfd seals associated with the file, if any. */
+static inline unsigned int memfd_file_seals(struct file *file)
+{
+ unsigned int *sealsp = memfd_file_seals_ptr(file);
+
+ return sealsp ? *sealsp : 0;
+}
+
#endif /* __LINUX_MEMFD_H */
diff --git a/include/linux/mm.h b/include/linux/mm.h
index 338a76ce9083..fb397918c43d 100644
--- a/include/linux/mm.h
+++ b/include/linux/mm.h
@@ -4101,6 +4101,37 @@ void mem_dump_obj(void *object);
static inline void mem_dump_obj(void *object) {}
#endif
+static inline bool is_write_sealed(int seals)
+{
+ return seals & (F_SEAL_WRITE | F_SEAL_FUTURE_WRITE);
+}
+
+/**
+ * is_readonly_sealed - Checks whether write-sealed but mapped read-only,
+ * in which case writes should be disallowing moving
+ * forwards.
+ * @seals: the seals to check
+ * @vm_flags: the VMA flags to check
+ *
+ * Returns whether readonly sealed, in which case writess should be disallowed
+ * going forward.
+ */
+static inline bool is_readonly_sealed(int seals, vm_flags_t vm_flags)
+{
+ /*
+ * Since an F_SEAL_[FUTURE_]WRITE sealed memfd can be mapped as
+ * MAP_SHARED and read-only, take care to not allow mprotect to
+ * revert protections on such mappings. Do this only for shared
+ * mappings. For private mappings, don't need to mask
+ * VM_MAYWRITE as we still want them to be COW-writable.
+ */
+ if (is_write_sealed(seals) &&
+ ((vm_flags & (VM_SHARED | VM_WRITE)) == VM_SHARED))
+ return true;
+
+ return false;
+}
+
/**
* seal_check_write - Check for F_SEAL_WRITE or F_SEAL_FUTURE_WRITE flags and
* handle them.
@@ -4112,24 +4143,15 @@ static inline void mem_dump_obj(void *object) {}
*/
static inline int seal_check_write(int seals, struct vm_area_struct *vma)
{
- if (seals & (F_SEAL_WRITE | F_SEAL_FUTURE_WRITE)) {
- /*
- * New PROT_WRITE and MAP_SHARED mmaps are not allowed when
- * write seals are active.
- */
- if ((vma->vm_flags & VM_SHARED) && (vma->vm_flags & VM_WRITE))
- return -EPERM;
+ if (!is_write_sealed(seals))
+ return 0;
- /*
- * Since an F_SEAL_[FUTURE_]WRITE sealed memfd can be mapped as
- * MAP_SHARED and read-only, take care to not allow mprotect to
- * revert protections on such mappings. Do this only for shared
- * mappings. For private mappings, don't need to mask
- * VM_MAYWRITE as we still want them to be COW-writable.
- */
- if (vma->vm_flags & VM_SHARED)
- vm_flags_clear(vma, VM_MAYWRITE);
- }
+ /*
+ * New PROT_WRITE and MAP_SHARED mmaps are not allowed when
+ * write seals are active.
+ */
+ if ((vma->vm_flags & VM_SHARED) && (vma->vm_flags & VM_WRITE))
+ return -EPERM;
return 0;
}
diff --git a/mm/memfd.c b/mm/memfd.c
index c17c3ea701a1..35a370d75c9a 100644
--- a/mm/memfd.c
+++ b/mm/memfd.c
@@ -170,7 +170,7 @@ static int memfd_wait_for_pins(struct address_space *mapping)
return error;
}
-static unsigned int *memfd_file_seals_ptr(struct file *file)
+unsigned int *memfd_file_seals_ptr(struct file *file)
{
if (shmem_file(file))
return &SHMEM_I(file_inode(file))->seals;
diff --git a/mm/mmap.c b/mm/mmap.c
index d32b7e701058..16f8e8be01f8 100644
--- a/mm/mmap.c
+++ b/mm/mmap.c
@@ -47,6 +47,7 @@
#include <linux/oom.h>
#include <linux/sched/mm.h>
#include <linux/ksm.h>
+#include <linux/memfd.h>
#include <linux/uaccess.h>
#include <asm/cacheflush.h>
@@ -368,6 +369,7 @@ unsigned long do_mmap(struct file *file, unsigned long addr,
if (file) {
struct inode *inode = file_inode(file);
+ unsigned int seals = memfd_file_seals(file);
unsigned long flags_mask;
if (!file_mmap_ok(file, inode, pgoff, len))
@@ -408,6 +410,8 @@ unsigned long do_mmap(struct file *file, unsigned long addr,
vm_flags |= VM_SHARED | VM_MAYSHARE;
if (!(file->f_mode & FMODE_WRITE))
vm_flags &= ~(VM_MAYWRITE | VM_SHARED);
+ else if (is_readonly_sealed(seals, vm_flags))
+ vm_flags &= ~VM_MAYWRITE;
fallthrough;
case MAP_PRIVATE:
if (!(file->f_mode & FMODE_READ))