linaro-dev

linaro-dev@lists.linaro.org

4332 discussions

Problem booting using latest linaro-linux-tracking (3.16.0-rc5)/mainline kernel (3.16.0-rc4) on Samsung Arndale Baord

by Mohammad Merajul Islam Molla

Hello, I am having problem booting from latest linaro-linux-tracking (3.16.0-rc5) on Samsung Arndale Board (with two cpus). The same thing happens with mainline kernel (3.16.0-rc4). Here is what happens - 1. During build I got the error message - LD sound/built-in.o MK_FW firmware/edid-1920x1080.fw.gen.S make[1]: *** No rule to make target `firmware/edid-1920x1080.fw', needed by `firmware/edid-1920x1080.fw.gen.o'. Stop. make: *** [firmware] Error 2 I set CONFIG_EXTRA_FIRMWARE="" and could proceed with build. 2. At the end of build I got the below error message - Kernel: arch/arm/boot/zImage is ready multiple (or no) load addresses: This is incompatible with uImages Specify LOADADDR on the commandline to build an uImage make[1]: *** [arch/arm/boot/uImage] Error 1 make: *** [uImage] Error 2 I passed loadaddr as parameter - make uImage LOADADDR=0x40008000 (this address I got from build output of linux-linaro-tracking 3.14.0). With this build was successful and uImage generated. 3. After that I got the following log during boot - [ 1.125626] Trying to unpack rootfs image as initramfs... [ 1.243435] Freeing initrd memory: 2384K (82001000 - 82255000) [ 1.243760] hw perfevents: enabled with ARMv7_Cortex_A15 PMU driver, 7 counters available [ 1.244915] futex hash table entries: 512 (order: 3, 32768 bytes) [ 1.244991] audit: initializing netlink subsys (disabled) [ 1.245035] audit: type=2000 audit(1.225:1): initialized [ 1.246360] VFS: Disk quotas dquot_6.5.2 [ 1.246428] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.247297] NFS: Registering the id_resolver key type [ 1.247335] Key type id_resolver registered [ 1.247350] Key type id_legacy registered [ 1.247403] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 1.247775] msgmni has been set to 3482 [ 1.249383] bounce: pool size: 64 pages [ 1.249440] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 1.249462] io scheduler noop registered [ 1.249479] io scheduler deadline registered [ 1.249512] io scheduler cfq registered (default) [ 1.260046] dma-pl330 121a0000.pdma: Loaded driver for PL330 DMAC-2364208 [ 1.260068] dma-pl330 121a0000.pdma: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.263447] dma-pl330 121b0000.pdma: Loaded driver for PL330 DMAC-2364208 [ 1.263467] dma-pl330 121b0000.pdma: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.264525] dma-pl330 10800000.mdma: Loaded driver for PL330 DMAC-2364208 [ 1.264545] dma-pl330 10800000.mdma: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.265467] dma-pl330 11c10000.mdma: Loaded driver for PL330 DMAC-2364208 [ 1.265486] dma-pl330 11c10000.mdma: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.265562] xenfs: not registering filesystem on non-xen platform [ 1.335655] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.337195] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 83, base_baud = 0) is a S3C6400/10 [ 1.337589] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 84, base_baud = 0) is a S3C6400/10 [ 1.338017] 12c20000.serial: ttySAC2 at MMIO 0x12c20000 (irq = 85, base_baud = 0) is a S3C6400/10 [ 2.275531] console [ttySAC2] enabled [ 2.279568] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 86, base_baud = 0) is a S3C6400/10 [ 2.288628] [drm] Initialized drm 1.1.0 20060810 [ 2.300603] [drm:hdmi_probe] *ERROR* syscon regmap lookup failed. [ 2.305611] platform 14530000.hdmi: Driver exynos-hdmi requests probe deferral [ 2.320592] brd: module loaded [ 2.326213] loop: module loaded [ 2.328789] mtdoops: mtd device (mtddev=name/number) must be supplied [ 2.334354] tun: Universal TUN/TAP device driver, 1.6 [ 2.339351] tun: (C) 1999-2004 Max Krasnyansky <maxk(a)qualcomm.com> [ 2.345896] usbcore: registered new interface driver asix [ 2.350960] usbcore: registered new interface driver ax88179_178a [ 2.357027] usbcore: registered new interface driver cdc_ether [ 2.362843] usbcore: registered new interface driver dm9601 [ 2.368402] usbcore: registered new interface driver net1080 [ 2.374039] usbcore: registered new interface driver cdc_subset [ 2.379945] usbcore: registered new interface driver zaurus [ 2.385498] usbcore: registered new interface driver MOSCHIP usb-ethernet driver [ 2.392913] usbcore: registered new interface driver cdc_ncm [ 2.399041] usb@12000000 supply vdd33 not found, using dummy regulator [ 2.405044] usb@12000000 supply vdd10 not found, using dummy regulator [ 2.411844] platform 12000000.dwc3: Driver dwc3 requests probe deferral [ 2.418250] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.424599] ehci-pci: EHCI PCI platform driver [ 2.429075] ehci-exynos: EHCI EXYNOS driver [ 2.433439] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.439368] ohci-pci: OHCI PCI platform driver [ 2.443831] ohci-exynos: OHCI EXYNOS driver [ 2.448256] usbcore: registered new interface driver usb-storage [ 2.462756] usb3503 usb_hub_bus:usb_hub: switched to HUB mode [ 2.467037] usb3503 usb_hub_bus:usb_hub: usb3503_probe: probed in hub mode [ 2.474499] samsung-usb3phy 12100000.usbphy: Can't get usb-phy sysreg cfg register [ 2.482379] mousedev: PS/2 mouse device common for all mice [ 2.487859] s3c-rtc 101e0000.rtc: rtc disabled, re-enabling [ 2.493050] s3c-rtc 101e0000.rtc: rtc core: registered s3c as rtc0 [ 2.498744] s3c-rtc 101e0000.rtc: warning: invalid RTC value so initializing it [ 2.506404] 10060000.tmu supply vtmu not found, using dummy regulator [ 2.512972] exynos-tmu 10060000.tmu: Exynos: Thermal zone(therm_zone0) registered [ 2.520421] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: dm-devel(a)redhat.com [ 2.539598] Synopsys Designware Multimedia Card Interface Driver [ 2.544808] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 2.550567] dwmmc_exynos 12200000.mmc: Version ID is 241a [ 2.556606] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 107, 32 bit host data width, 128 deep fifo [ 2.592839] dwmmc_exynos 12200000.mmc: 1 slots initialized [ 2.597196] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 2.603300] dwmmc_exynos 12220000.mmc: Version ID is 241a [ 2.609998] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 109, 32 bit host data width, 128 deep fifo [ 2.647788] dwmmc_exynos 12220000.mmc: 1 slots initialized [ 2.652056] usbcore: registered new interface driver usbhid [ 2.657359] usbhid: USB HID core driver [ 2.662438] oprofile: using timer interrupt. [ 2.665558] TCP: cubic registered [ 2.668730] Initializing XFRM netlink socket [ 2.673030] NET: Registered protocol family 10 [ 2.677915] sit: IPv6 over IPv4 tunneling driver [ 2.682464] NET: Registered protocol family 17 [ 2.686472] NET: Registered protocol family 15 [ 2.690938] Key type dns_resolver registered [ 2.695208] Registering SWP/SWPB emulation handler [ 2.700832] Btrfs loaded [ 2.702450] AppArmor: AppArmor sha1 policy hashing enabled [ 2.708691] mfc-power-domain: Power-off latency exceeded, new value 8731958 ns [ 2.715660] gsc-power-domain: Power-off latency exceeded, new value 308750 ns [ 2.725830] mmc0: BKOPS_EN bit is not set [ 2.729770] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) [ 2.738186] [drm:hdmi_probe] *ERROR* syscon regmap lookup failed. [ 2.744521] platform 14530000.hdmi: Driver exynos-hdmi requests probe deferral [ 2.952480] mmc_host mmc0: Bus speed (slot 0) = 100000000Hz (slot req 52000000Hz, actual 50000000HZ div = 1) [ 2.960942] mmc0: new DDR MMC card at address 0001 [ 2.966013] mmcblk0: mmc0:0001 M4G1FB 3.64 GiB [ 2.970244] mmcblk0boot0: mmc0:0001 M4G1FB partition 1 1.00 MiB [ 2.976150] mmcblk0boot1: mmc0:0001 M4G1FB partition 2 1.00 MiB [ 2.982039] mmcblk0rpmb: mmc0:0001 M4G1FB partition 3 128 KiB [ 2.989206] mmcblk0: p1 p2 p3 p4 [ 2.993050] mmcblk0boot1: unknown partition table [ 2.997278] mmcblk0boot0: unknown partition table [ 3.008951] [drm:hdmi_probe] *ERROR* syscon regmap lookup failed. [ 3.013956] platform 14530000.hdmi: Driver exynos-hdmi requests probe deferral [ 3.029510] [drm:hdmi_probe] *ERROR* syscon regmap lookup failed. [ 3.034475] platform 14530000.hdmi: Driver exynos-hdmi requests probe deferral [ 3.042326] input: gpio_keys as /devices/gpio_keys/input/input0 [ 3.047643] s3c-rtc 101e0000.rtc: setting system clock to 2000-01-01 00:00:01 UTC (946684801) [ 3.080561] vdd_g3d: disabling [ 3.100380] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 3.108670] mmc1: new high speed SDHC card at address aaaa [ 3.114356] VDD_IOPERI_1.8V: disabling [ 3.117998] mmcblk1: mmc1:aaaa SU04G 3.69 GiB [ 3.124076] mmcblk1: p1 p2 p3 [ 3.126718] hdmi-en: disabling [ 3.128710] MAIN_DC: disabling [ 3.132350] ALSA device list: [ 3.134687] No soundcards found. [ 3.139126] Freeing unused kernel memory: 472K (8077c000 - 807f2000) [ 3.152292] [drm:hdmi_probe] *ERROR* syscon regmap lookup failed. [ 3.157359] platform 14530000.hdmi: Driver exynos-hdmi requests probe deferral Loading, please wait... [ 3.172053] [drm:hdmi_probe] *ERROR* syscon regmap lookup failed. [ 3.177045] platform 14530000.hdmi: Driver exynos-hdmi requests probe deferral [ 3.204532] systemd-udevd[1350]: starting version 204 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. [ 3.749107] EXT4-fs (mmcblk1p3): mounted filesystem with ordered data mode. Opts: (null) Begin: Running /scripts/local-bottom ... done. done. Begin: Running /scripts/init-bottom ... done. [ 3.841975] random: nonblocking pool is initialized [ 4.987813] init: ureadahead main process (1399) terminated with status 5 [ 5.859210] EXT4-fs (mmcblk1p3): re-mounted. Opts: errors=remount-ro [ 7.738335] CPU1: failed to boot: -19 Looks like CPU1 failed to boot. But on the same board, using same SD card and linux-linaro-tracking v3.14.0 it boots successfully. 4. Tried to boot passing argument 'maxcpus=1' via uboot but keeps getting the same error. 5. Tried to build kernel without SMP support and keeps getting the below build error - scripts/kconfig/conf --silentoldconfig Kconfig CHK include/config/kernel.release CHK include/generated/uapi/linux/version.h CHK include/generated/utsrelease.h make[1]: `include/generated/mach-types.h' is up to date. CALL scripts/checksyscalls.sh CHK include/generated/compile.h CC arch/arm/kernel/process.o In file included from ./arch/arm/include/asm/hardirq.h:6:0, from include/linux/hardirq.h:8, from include/linux/interrupt.h:12, from arch/arm/kernel/process.c:22: ./arch/arm/include/asm/irq.h:39:40: error: conflicting types for ‘arch_trigger_all_cpu_backtrace’ #define arch_trigger_all_cpu_backtrace arch_trigger_all_cpu_backtrace ^ arch/arm/kernel/process.c:69:6: note: in expansion of macro ‘arch_trigger_all_cpu_backtrace’ void arch_trigger_all_cpu_backtrace(void) ^ ./arch/arm/include/asm/irq.h:38:6: note: previous declaration of ‘arch_trigger_all_cpu_backtrace’ was here void arch_trigger_all_cpu_backtrace(bool); ^ make[1]: *** [arch/arm/kernel/process.o] Error 1 config file attached. Using same config file, I don't get any build error mentioned in 1 & 2 with linaro-linux-tracking v3.14.0 and it boots ok. Is there something I am doing wrong or is it problem with recent kernel? -- Thanks, -Meraj

11 years, 1 month

[PATCH PMQA] cpuidle: increase wait time for child to finish

by Sanjay Singh Rawat

- fix for bug 152 on Panda, wait for more time for child to finish - don't wait for child pid for offlined cpus - bug 152 Signed-off-by: Sanjay Singh Rawat <sanjay.rawat(a)linaro.org> --- cpuidle/cpuidle_killer.c | 8 +++++++- 1 file changed, 7 insertions(+), 1 deletion(-) diff --git a/cpuidle/cpuidle_killer.c b/cpuidle/cpuidle_killer.c index ae3b54f..49fe1ea 100644 --- a/cpuidle/cpuidle_killer.c +++ b/cpuidle/cpuidle_killer.c @@ -181,11 +181,17 @@ int main(int argc, char *argv[]) signal(SIGALRM, timeout); - alarm(DURATION + 5); + alarm(DURATION + 20); for (i = 0; i < nrcpus; i++) { int status; + /* skip for offline cpus */ + if (!pids[i]) { + fprintf(stderr, "no_wait_for_process on cpu %d\n", i); + continue; + } + waitpid(pids[i], &status, 0); if (status != 0) { fprintf(stderr, "test for cpu %d has failed\n", i); -- 1.8.3.2

11 years, 1 month

[PATCH PM-QA] heat_cpu: fix race condition

by Mohammad Merajul Islam Molla

fixes race condition that exists between do_loop() and sched_setaffinity() on android. due to synchronization problem, sched_setaffinity() was setting affinity for thr_id 0 randomly. also, allocate the thr_id's dynamically instead of fixed array size 3. tested on Linaro Android 14.04. Signed-off-by: Mohammad Merajul Islam Molla <meraj.enigma(a)gmail.com> --- utils/heat_cpu.c | 35 +++++++++++++++++++---------------- 1 file changed, 19 insertions(+), 16 deletions(-) diff --git a/utils/heat_cpu.c b/utils/heat_cpu.c index 02e0b6d..716cd56 100644 --- a/utils/heat_cpu.c +++ b/utils/heat_cpu.c @@ -47,17 +47,14 @@ #include <string.h> #include <math.h> -#define NR_THREAD 3 - int cont = 1; int cpu_index; long long a = 1, c = 1; float f = M_PI; -pid_t thr_id[NR_THREAD]; +pid_t *thr_id; int moderate_inst; - #ifdef ANDROID int conditionMet; pthread_cond_t cond = PTHREAD_COND_INITIALIZER; @@ -72,11 +69,11 @@ void *do_loop(void *data) a = 1; c = 1; #ifdef ANDROID + pthread_mutex_lock(&mutex); long int thread = (long int) data; thr_id[thread] = gettid(); - pthread_mutex_lock(&mutex); - while (!conditionMet) - pthread_cond_wait(&cond, &mutex); + conditionMet = 1; + pthread_cond_broadcast(&cond); pthread_mutex_unlock(&mutex); #endif @@ -112,6 +109,12 @@ int main(int arg_count, char *argv[]) } } + thr_id = (pid_t *) calloc(num_cpus, sizeof(pid_t)); + if (thr_id == NULL) { + printf("ERROR: out of memory\n"); + return -1; + } + /* clear out cpus */ CPU_ZERO(&cpuset); @@ -161,8 +164,7 @@ int main(int arg_count, char *argv[]) return ret; } #endif - CPU_CLR(i, &cpuset); - + CPU_CLR(i, &cpuset); } for (i = 0; i < num_cpus; i++) { @@ -176,23 +178,24 @@ int main(int arg_count, char *argv[]) CPU_ZERO(&cpuset); CPU_SET(i, &cpuset); + pthread_mutex_lock(&mutex); + while (!conditionMet) + pthread_cond_wait(&cond, &mutex); + ret = sched_setaffinity(thr_id[i], sizeof(cpuset), &cpuset); if (ret) { printf("Error setting affinity on pthread th_id\n"); printf("Error: %s\n", strerror(ret)); return ret; } -#endif - } -#ifdef ANDROID - pthread_mutex_lock(&mutex); - conditionMet = 1; - pthread_cond_broadcast(&cond); - pthread_mutex_unlock(&mutex); + conditionMet = 0; + pthread_mutex_unlock(&mutex); #endif + } while (1) sleep(1); + return 0; } -- 1.8.1.2 -- Thanks, -Meraj

11 years, 1 month

[ACTIVITY] week 28

by Dileep Katta

== Progress == * Enabling UEFI Fastboot on Panda - on hold (CARD-198: 0 %) * CARD 1103: Flash support on u-boot fastboot, Added DFU APIs, made a commit (CARD-1103: 70%) * CARD 1103: Flash support on u-boot fastboot, Fixing issues with DFU code in Flashing command (CARD-1103: 30%) == Plans == * CARD-198: Pause (0%) * CARD 1103: Flash support on u-boot fastboot, fixing Partition identification issues, Making flashing command work (CARD-1103: 100%) == Issues == * None

11 years, 1 month

[ACTIVITY] Week28

by Wookey

== Progress == * Buildd-tending: Debian arm64 is at 80% built (DEVPLAT-226: 5%) http://buildd.debian-ports.org/stats/graph-quarter-big.png * NMUed 20-odd packages with arm64 fixes. (DEVPLAT-221: 20%) * NMUed fixed SCC packages: libgc, libfcgi, corosync, soprano, openais (DEVPLAT-226: 20%) * Fixed and NMUed SCC package: radvd, gtklext, policykit-1 (DEVPLAT-226: 10%) * Investigated and filed bugs for icu, keyutils (DEVPLAT-226: 5%) * Worked with upstream to fix elfutils (DEVPLAT-226: 5%) * Fixed openjdk/zookeeper missing save_sp_reg patch (DEVPLAT-219: 10%) * Updated/uploaded cross-binutils package (now in Archive) (DEVPLAT-220) (5%) * Finalised Bootstrap/crossbuild sprint for Paris/August (20%) * Extended sortblockers script to generate outofdate list: http://people.debian.org/~wookey/bootstrap/outofdatelist (2%) * Investigated crappy connection to china (losing 60% of my packets). V annoying.(10%) * Badgered ARM re hardware for arm64 port. == Plans == * Fix/NMU remaining packages in SCC http://people.debian.org/~wookey/bootstrap/blockerlist * Investigate PDF build errors. * Mail release team about arm64 prospects == Issues == Network conenction to china is often very flaky. Duploads fail repeatedly and intereactive use over mosh stalls a lot. Frustrating. Wookey -- Principal hats: Linaro, Emdebian, Wookware, Balloonboard, ARM http://wookware.org/

11 years, 2 months

[ACTIVITY] Week 28

by Harigopal Gollamudi

== Progress == DEVPLAT-238: CI Loop for LSK 3.14 kernel for ARMv7 and ARMv8 == Plans == Booting Vayu board deployed in Lava lab with Android binaries == Issues == None -- Thanks and Regards, HariGopal G Android Engineer

11 years, 2 months

[ACTIVITY] week 28

by Bernhard Rosenkränzer

== Progress == * New Bionic memchr() for Aarch64 * zlib optimization analyzis * started some cbuildv2 toolchain builds for testing * restored Galaxy Nexus support in Android builds (4.4.4) * participated in calls about the Android microconf at LPC2014 == Plans == * Fix issues with cbuildv2 toolchain builds * check if AOSP master can run on Galaxy Nexus * Port some recent Bionic aarch64 improvements to armv7 == Issues == * ci.linaro.org is broken

11 years, 2 months

[meta-linaro-toolchain][PATCH] external-linaro-toolchain: Add eglibc-mtrace to RPROVIDES

by b40527＠freescale.com

From: Zongchun Yu <Zongchun.Yu(a)freescale.com> The mtrace should be provided by external toolchain instead of eglibc-mtrace. Signed-off-by: Zongchun Yu <Zongchun.Yu(a)freescale.com> --- .../external-linaro-toolchain/external-linaro-toolchain.bb | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/meta-linaro-toolchain/recipes-devtools/external-linaro-toolchain/external-linaro-toolchain.bb b/meta-linaro-toolchain/recipes-devtools/external-linaro-toolchain/external-linaro-toolchain.bb index 06abb7a..bb4cfae 100644 --- a/meta-linaro-toolchain/recipes-devtools/external-linaro-toolchain/external-linaro-toolchain.bb +++ b/meta-linaro-toolchain/recipes-devtools/external-linaro-toolchain/external-linaro-toolchain.bb @@ -72,6 +72,7 @@ do_install() { fi cp -a ${EXTERNAL_TOOLCHAIN}/${ELT_TARGET_SYS}/libc/usr/share/* ${D}${datadir} cp -a ${EXTERNAL_TOOLCHAIN}/${ELT_TARGET_SYS}/libc/usr/include/* ${D}${includedir} + cp -a ${EXTERNAL_TOOLCHAIN}/${ELT_TARGET_SYS}/libc/usr/bin/mtrace ${D}${bindir} if [ -d ${EXTERNAL_TOOLCHAIN}/${ELT_TARGET_SYS}/libc/usr/include/${ELT_TARGET_SYS} ]; then cp -a ${EXTERNAL_TOOLCHAIN}/${ELT_TARGET_SYS}/libc/usr/include/${ELT_TARGET_SYS}/* ${D}${includedir} @@ -155,6 +156,7 @@ INSANE_SKIP_gdbserver += "ldflags" PKG_${PN} = "eglibc" PKG_${PN}-dev = "eglibc-dev" PKG_${PN}-doc = "eglibc-doc" +PKG_${PN}-mtrace = "eglibc-mtrace" PKG_${PN}-dbg = "eglibc-dbg" PKG_${PN}-pic = "eglibc-pic" PKG_${PN}-utils = "eglibc-utils" @@ -164,6 +166,8 @@ PKG_${PN}-thread-db = "eglibc-thread-db" PKG_${PN}-pcprofile = "eglibc-pcprofile" PKG_${PN}-staticdev = "eglibc-staticdev" +RPROVIDES_${PN}-mtrace += "${TCLIBC}-mtrace" + PKGV_${PN} = "${ELT_VER_LIBC}" PKGV_${PN}-dev = "${ELT_VER_LIBC}" PKGV_${PN}-doc = "${ELT_VER_LIBC}" -- 1.8.3.2

11 years, 2 months

[ACTIVITY] week 27

by Andrey Konovalov

== Progress == * moved linux-linaro-core-tracking and linux-linaro to v3.16-rc3, added llvm topic back to linux-linaro (CARD-788, 60%) * added QCOM LT tree to linux-linaro, boot tested in LAVA (CARD-788, 40%) * DEVPLAT-210 "upstream: fastboot in u-boot": synced up with Dileep (0%) == Plans == * move linux-linaro-core-tracking and linux-linaro to v3.16-rc4, make all the topics fixed for 3.16 (CARD-788) * add QCOM's ifc6410 board to linux-linaro CI loop (CARD-788) * complete the ILP32 topic branch for ll, sanity check it with LTP in LP64, identify the missing components needed for testing in ILP32 (CARD-1161) * follow up on: . DEVPLAT-210 "upstream: fastboot in u-boot" . bug 1189839 "kernel crash on arndale while CPU hotplug" * update the wiki doc for DEVPLAT-204 == Issues == * none

11 years, 2 months

[PATCH] Add pinctrl support in powerdebug

by Mohammad Merajul Islam Molla

Add support for pinctrl in powerdebug. Both dump and display modes supported. Tested only on Samsung Arndale board. Sample output in display mode on Arndale Board - Pin Name MUX Owner GPIO Owner HOG Function Group 0 gpa0-0 MUX UNCLAIMED GPIO UNCLAIMED 1 gpa0-1 MUX UNCLAIMED GPIO UNCLAIMED 2 gpa0-2 MUX UNCLAIMED GPIO UNCLAIMED 3 gpa0-3 MUX UNCLAIMED GPIO UNCLAIMED 4 gpa0-4 MUX UNCLAIMED GPIO UNCLAIMED 5 gpa0-5 MUX UNCLAIMED GPIO UNCLAIMED 6 gpa0-6 12c80000.i2c GPIO UNCLAIMED i2c2-bus-mux i2c2-bus-grp 7 gpa0-7 12c80000.i2c GPIO UNCLAIMED i2c2-bus-mux i2c2-bus-grp 8 gpa1-0 MUX UNCLAIMED GPIO UNCLAIMED 9 gpa1-1 MUX UNCLAIMED GPIO UNCLAIMED 10 gpa1-2 12c90000.i2c GPIO UNCLAIMED i2c3-bus-mux i2c3-bus-grp 11 gpa1-3 12c90000.i2c GPIO UNCLAIMED i2c3-bus-mux i2c3-bus-grp --- Android.mk | 2 +- Makefile | 2 +- README | 4 +- display.c | 3 +- display.h | 2 +- pinctrl.c | 329 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ pinctrl.h | 19 ++++ powerdebug.c | 35 +++++-- 8 files changed, 381 insertions(+), 15 deletions(-) create mode 100644 pinctrl.c create mode 100644 pinctrl.h diff --git a/Android.mk b/Android.mk index 36c73cd..19d00ca 100644 --- a/Android.mk +++ b/Android.mk @@ -29,6 +29,6 @@ LOCAL_C_INCLUDES += external/stlport/stlport/ \ LOCAL_SRC_FILES += \ powerdebug.c sensor.c clocks.c regulator.c \ - display.c tree.c utils.c mainloop.c gpio.c + display.c tree.c utils.c mainloop.c gpio.c pinctrl.c include $(BUILD_EXECUTABLE) diff --git a/Makefile b/Makefile index 2da9d67..f002438 100644 --- a/Makefile +++ b/Makefile @@ -5,7 +5,7 @@ CFLAGS?=-O1 -g -Wall -Wshadow CC?=gcc OBJS = powerdebug.o sensor.o clocks.o regulator.o gpio.o \ - display.o tree.o utils.o mainloop.o + display.o tree.o utils.o mainloop.o pinctrl.o default: powerdebug diff --git a/README b/README index 1479db1..b24dd98 100644 --- a/README +++ b/README @@ -1,8 +1,8 @@ powerdebug ---------- -This is a new tool which displays regulator, sensor and clock tree -information. +This is a new tool which displays regulator, sensor, clock tree, gpio and +pinctrl information. Current version only displays regulator information and clock tree from debugfs. Support will be added for sensors later. diff --git a/display.c b/display.c index 0000ee9..fb899c0 100644 --- a/display.c +++ b/display.c @@ -63,7 +63,8 @@ struct windata windata[] = { [CLOCK] = { .name = "Clocks" }, [REGULATOR] = { .name = "Regulators" }, [SENSOR] = { .name = "Sensors" }, - [GPIO] = { .name = "Gpio" }, + [GPIO] = { .name = "Gpio" }, + [PINCTRL] = { .name = "Pins" }, }; static void display_fini(void) diff --git a/display.h b/display.h index e3a1529..4496f30 100644 --- a/display.h +++ b/display.h @@ -13,7 +13,7 @@ * - initial API and implementation *******************************************************************************/ -enum { CLOCK, REGULATOR, SENSOR, GPIO }; +enum { CLOCK, REGULATOR, SENSOR, GPIO, PINCTRL }; struct display_ops { int (*display)(bool refresh); diff --git a/pinctrl.c b/pinctrl.c new file mode 100644 index 0000000..eef06e2 --- /dev/null +++ b/pinctrl.c @@ -0,0 +1,329 @@ + +/******************************************************************************* + * Copyright (C) 2014, Linaro Limited. + * + * This file is part of PowerDebug. + * + * All rights reserved. This program and the accompanying materials + * are made available under the terms of the Eclipse Public License v1.0 + * which accompanies this distribution, and is available at + * http://www.eclipse.org/legal/epl-v10.html + * + * Contributors: + * Mohammad Merajul Islam Molla <meraj.molla(a)samsung.com> + * (Samsung R&D Institute Bangladesh) + * - initial API and implementation + *******************************************************************************/ + +#ifndef _GNU_SOURCE +#define _GNU_SOURCE +#include <stdio.h> +#undef _GNU_SOURCE +#endif +#include <string.h> +#include <stdbool.h> +#include <unistd.h> +#include <stdlib.h> +#include <dirent.h> +#include <sys/stat.h> +#include <sys/types.h> + +#include "pinctrl.h" +#include "display.h" + +#define SIZE 64 +#define MAX_PINS 256 + +#define PIN_fmt "%*[^ ] %d" +#define NAME_fmt "%*[^(]( %s" +#define MUX_fmt "%*[^:]: %s" +#define GPIO_fmt "%*[^:]: %*[^ ] %s" +#define GPIO_fmt1 "%*[^:]: %*[^ ] %*[^ ] %s" + +#define SYS_PINCTRL "/sys/kernel/debug/pinctrl" + +static bool pinctrl_error = false; + +static struct pintcrl_info { + int pin; + char name[SIZE]; + char mux_owner[SIZE]; + char gpio_owner[SIZE]; + char hog[SIZE]; + char function[SIZE]; + char group[SIZE]; +} pins_info[MAX_PINS]; + +static int fill_pinctrl_info(); + +static int pinctrl_print_header(void) +{ + char *buf; + int ret; + + if (asprintf(&buf, "%-5s %-10s %-15s %-15s %-5s %-20s %-20s", + "Pin", "Name", "MUX Owner", "GPIO Owner", "HOG", "Function", + "Group") < 0) + return -1; + + ret = display_column_name(buf); + + free(buf); + + return ret; +} + +static char *pin_line(int pin) +{ + char *pinline = 0; + + if (asprintf(&pinline,"%-5d %-10s %-15s %-15s %-5s %-20s %-20s", + pins_info[pin].pin, pins_info[pin].name, + pins_info[pin].mux_owner, pins_info[pin].gpio_owner, + pins_info[pin].hog, pins_info[pin].function, + pins_info[pin].group) < 0) + return NULL; + + return pinline; +} + +static int pinctrl_print_info() +{ + int i; + int line = 0; + char *buffer; + + display_reset_cursor(PINCTRL); + + pinctrl_print_header(); + + for (i = 0; i < MAX_PINS; i++) { + if (pins_info[i].pin == -1) + continue; + + buffer = pin_line(i); + if (!buffer) + return -1; + + display_print_line(PINCTRL, line, buffer, 0, NULL); + line++; + + free(buffer); + } + + display_refresh_pad(PINCTRL); + + return 0; +} + +static int dump_pinctrl_info() +{ + int i; + + for (i = 0; i < MAX_PINS; i++) { + if (pins_info[i].pin == -1) + continue; + printf("\tPin %d: (Name: %s, MUX_owner: %s, GPIO_owner: %s, HOG: %s, Function: %s, Group: %s)\n", + pins_info[i].pin, pins_info[i].name, + pins_info[i].mux_owner, pins_info[i].gpio_owner, + pins_info[i].hog, + pins_info[i].function, pins_info[i].group); + } + + return 0; +} + + +int pinctrl_dump() +{ + int ret; + + if (pinctrl_error) + return -1; + + printf("\nPin Information:\n"); + printf("****************\n"); + ret = dump_pinctrl_info(); + printf("\n\n"); + + return ret; + +} + +static int pinctrl_display(bool refresh) +{ + if (pinctrl_error) { + display_message(PINCTRL, + "error: path " SYS_PINCTRL " not found or not root"); + return -2; + } + + if (refresh && fill_pinctrl_info()) + return -1; + + return pinctrl_print_info(); +} + +static struct display_ops pinctrl_ops = { + .display = pinctrl_display, +}; + +static int read_pin_info(const char *path) +{ + FILE *fpinmux; + int pin; + int ret = 0; + char *p; + char buf[4096]; + + fpinmux = fopen(path, "r"); + if (!fpinmux) { + printf("error: failed to read %s\n", path); + return -1; + } + + /* first two lines are headers, ignore */ + fgets(buf, 4096, fpinmux); + fgets(buf, 4096, fpinmux); + + while (fgets(buf, 4096, fpinmux)) { + int mux_owner = 0; + + /* get pin number */ + sscanf(buf, PIN_fmt, &pin); + + if (pin >= MAX_PINS) { + printf("WARNING: # of pins > max pins (256), need to increase limit\n"); + continue; + } + + pins_info[pin].pin = pin; + sscanf(buf, NAME_fmt, pins_info[pin].name); + pins_info[pin].name[strlen(pins_info[pin].name) - 2] = '\0'; + + if (strstr(buf, "MUX UNCLAIMED")) + strcpy(pins_info[pin].mux_owner, "MUX UNCLAIMED"); + else { + sscanf(buf, MUX_fmt, pins_info[pin].mux_owner); + mux_owner = 1; + } + + if (strstr(buf, "GPIO UNCLAIMED")) + strcpy(pins_info[pin].gpio_owner, "GPIO UNCLAIMED"); + else { + if (mux_owner) + sscanf(buf, GPIO_fmt, pins_info[pin].gpio_owner); + else + sscanf(buf, GPIO_fmt1, pins_info[pin].gpio_owner); + } + + if (strstr(buf, "HOG")) + strcpy(pins_info[pin].hog, "HOG"); + else + strcpy(pins_info[pin].hog, ""); + + if ((p = strstr(buf, "function"))) { + p += 9; + sscanf(p, "%s", pins_info[pin].function); + } + else + strcpy(pins_info[pin].function, ""); + + if ((p = strstr(buf, "group"))) { + p += 5; + sscanf(p, "%s", pins_info[pin].group); + } + else + strcpy(pins_info[pin].group, ""); + } + + fclose(fpinmux); + return ret; +} + +static void init_pins_info() +{ + int i; + + memset(pins_info, 0, sizeof(pins_info)); + + for (i = 0; i < MAX_PINS; i++) + pins_info[i].pin = -1; +} + +static int fill_pinctrl_info() +{ + DIR *dir; + char *newpath, *pinmux_path; + struct dirent dirent, *direntp; + struct stat s; + int ret = 0; + + dir = opendir(SYS_PINCTRL); + if (!dir) { + printf("error: unable to open directory " SYS_PINCTRL); + ret = -1; + goto out; + } + + init_pins_info(); + + while (!readdir_r(dir, &dirent, &direntp)) { + ret = 0; + + if (!direntp) + break; + + if (direntp->d_name[0] == '.') + continue; + + ret = asprintf(&newpath, "%s/%s", SYS_PINCTRL, direntp->d_name); + if (ret < 0) + goto out; + + ret = stat(newpath, &s); + if (ret) + goto out_free_newpath; + + if (S_ISDIR(s.st_mode)) { + ret = asprintf(&pinmux_path, "%s/%s", newpath, + "pinmux-pins"); + if (ret < 0) + goto out_free_newpath; + + if (read_pin_info(pinmux_path)) { + ret = -1; + goto out_free_pinmux; + } + } + } + +out_free_pinmux: + free(pinmux_path); + +out_free_newpath: + free(newpath); + +out: + closedir(dir); + return ret; +} + +int pinctrl_init(void) +{ + int ret = 0; + + ret = display_register(PINCTRL, &pinctrl_ops); + if (ret) + printf("error: pinctrl display register failed"); + + if (access(SYS_PINCTRL, F_OK)) { + pinctrl_error = true; + return -1; + } + + if (fill_pinctrl_info()) + return -1; + + return ret; +} diff --git a/pinctrl.h b/pinctrl.h new file mode 100644 index 0000000..2fa4f3a --- /dev/null +++ b/pinctrl.h @@ -0,0 +1,19 @@ +/******************************************************************************* + * Copyright (C) 2014, Linaro Limited. + * + * This file is part of PowerDebug. + * + * All rights reserved. This program and the accompanying materials + * are made available under the terms of the Eclipse Public License v1.0 + * which accompanies this distribution, and is available at + * http://www.eclipse.org/legal/epl-v10.html + * + * Contributors: + * Mohammad merajul Islam Molla <meraj.molla(a)samsung.com> + * (Samsung R&D Institute Bangladesh) + * + * - initial API and implementation + *******************************************************************************/ + +extern int pinctrl_init(void); +extern int pinctrl_dump(void); diff --git a/powerdebug.c b/powerdebug.c index 6cf3a1b..b4f4833 100644 --- a/powerdebug.c +++ b/powerdebug.c @@ -26,6 +26,7 @@ #include "clocks.h" #include "sensor.h" #include "gpio.h" +#include "pinctrl.h" #include "mainloop.h" #include "powerdebug.h" @@ -35,13 +36,14 @@ void usage(void) { printf("Usage: powerdebug [OPTIONS]\n"); printf("\n"); - printf("powerdebug -d [ -r ] [ -s ] [ -c [ -p <clock-name> ] ] " + printf("powerdebug -d [ -r ] [ -s ] [ -p ][ -c [ -P <clock-name> ] ] " "[ -v ]\n"); - printf("powerdebug [ -r | -s | -c ]\n"); + printf("powerdebug [ -r | -s | -c | -p] \n"); printf(" -r, --regulator Show regulator information\n"); printf(" -s, --sensor Show sensor information\n"); printf(" -c, --clock Show clock information\n"); - printf(" -p, --findparents Show all parents for a particular" + printf(" -p, --pin Show pin information\n"); + printf(" -P, --findparents Show all parents for a particular" " clock\n"); printf(" -t, --time Set ticktime in seconds (eg. 10.0)\n"); printf(" -d, --dump Dump information once (no refresh)\n"); @@ -62,7 +64,8 @@ void version() * -s, --sensor : sensors * -c, --clock : clocks * -g, --gpio : gpios - * -p, --findparents : clockname whose parents have to be found + * -p, --pin : pins + * -P, --findparents : clockname whose parents have to be found * -t, --time : ticktime * -d, --dump : dump * -v, --verbose : verbose @@ -76,7 +79,8 @@ static struct option long_options[] = { { "sensor", 0, 0, 's' }, { "clock", 0, 0, 'c' }, { "gpio", 0, 0, 'g' }, - { "findparents", 1, 0, 'p' }, + { "pin", 0 , 0, 'p' }, + { "findparents", 1, 0, 'P' }, { "time", 1, 0, 't' }, { "dump", 0, 0, 'd' }, { "verbose", 0, 0, 'v' }, @@ -91,6 +95,7 @@ struct powerdebug_options { bool sensors; bool clocks; bool gpios; + bool pins; bool dump; unsigned int ticktime; int selectedwindow; @@ -108,7 +113,7 @@ int getoptions(int argc, char *argv[], struct powerdebug_options *options) while (1) { int optindex = 0; - c = getopt_long(argc, argv, "rscgp:t:dvVh", + c = getopt_long(argc, argv, "rscgpP:t:dvVh", long_options, &optindex); if (c == -1) break; @@ -131,6 +136,10 @@ int getoptions(int argc, char *argv[], struct powerdebug_options *options) options->selectedwindow = GPIO; break; case 'p': + options->pins = true; + options->selectedwindow = PINCTRL; + break; + case 'P': options->clkname = strdup(optarg); if (!options->clkname) { fprintf(stderr, "failed to allocate memory"); @@ -161,9 +170,9 @@ int getoptions(int argc, char *argv[], struct powerdebug_options *options) /* No system specified to be dump, let's default to all */ if (!options->regulators && !options->clocks && - !options->sensors && !options->gpios) - options->regulators = options->clocks = - options->sensors = options->gpios = true; + !options->sensors && !options->gpios && !options->pins) + options->regulators = options->clocks = options->sensors = + options->gpios = options->pins = true; if (options->selectedwindow == -1) options->selectedwindow = CLOCK; @@ -185,6 +194,9 @@ static int powerdebug_dump(struct powerdebug_options *options) if (options->gpios) gpio_dump(); + if (options->pins) + pinctrl_dump(); + return 0; } @@ -266,6 +278,11 @@ int main(int argc, char **argv) options->gpios = false; } + if (pinctrl_init()) { + printf("failed to initialize pinctrl\n"); + options->pins = false; + } + ret = options->dump ? powerdebug_dump(options) : powerdebug_display(options); -- Thanks, -Meraj

11 years, 2 months

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

linaro-dev