March 2025 - Linux-stable-mirror

[PATCH v2 6/7] media: mt9m114: Fix deadlock in get_frame_interval/set_frame_interval

by Mathis Foerst

Getting / Setting the frame interval using the V4L2 subdev pad ops get_frame_interval/set_frame_interval causes a deadlock, as the subdev state is locked in the [1] but also in the driver itself. In [2] it's described that the caller is responsible to acquire and release the lock in this case. Therefore, acquiring the lock in the driver is wrong. Remove the lock acquisitions/releases from mt9m114_ifp_get_frame_interval() and mt9m114_ifp_set_frame_interval(). [1] drivers/media/v4l2-core/v4l2-subdev.c - line 1129 [2] Documentation/driver-api/media/v4l2-subdev.rst Fixes: 24d756e914fc ("media: i2c: Add driver for onsemi MT9M114 camera sensor") Cc: stable(a)vger.kernel.org Signed-off-by: Mathis Foerst <mathis.foerst(a)mt.com> --- drivers/media/i2c/mt9m114.c | 8 -------- 1 file changed, 8 deletions(-) diff --git a/drivers/media/i2c/mt9m114.c b/drivers/media/i2c/mt9m114.c index 18419de6491d..9ab1147a9aaf 100644 --- a/drivers/media/i2c/mt9m114.c +++ b/drivers/media/i2c/mt9m114.c @@ -1644,13 +1644,9 @@ static int mt9m114_ifp_get_frame_interval(struct v4l2_subdev *sd, if (interval->which != V4L2_SUBDEV_FORMAT_ACTIVE) return -EINVAL; - mutex_lock(sensor->ifp.hdl.lock); - ival->numerator = 1; ival->denominator = sensor->ifp.frame_rate; - mutex_unlock(sensor->ifp.hdl.lock); - return 0; } @@ -1669,8 +1665,6 @@ static int mt9m114_ifp_set_frame_interval(struct v4l2_subdev *sd, if (interval->which != V4L2_SUBDEV_FORMAT_ACTIVE) return -EINVAL; - mutex_lock(sensor->ifp.hdl.lock); - if (ival->numerator != 0 && ival->denominator != 0) sensor->ifp.frame_rate = min_t(unsigned int, ival->denominator / ival->numerator, @@ -1684,8 +1678,6 @@ static int mt9m114_ifp_set_frame_interval(struct v4l2_subdev *sd, if (sensor->streaming) ret = mt9m114_set_frame_rate(sensor); - mutex_unlock(sensor->ifp.hdl.lock); - return ret; } -- 2.34.1

6 months, 1 week

1
0
0 0

[PATCH 1/2] USB: serial: option: add Telit Cinterion FE990B compositions

by Fabio Porcedda

Add the following Telit Cinterion FE990B40 compositions: 0x10b0: rmnet + tty (AT/NMEA) + tty (AT) + tty (AT) + tty (AT) + tty (diag) + DPL + QDSS (Qualcomm Debug SubSystem) + adb T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 7 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1bc7 ProdID=10b0 Rev=05.15 S: Manufacturer=Telit Cinterion S: Product=FE990 S: SerialNumber=28c2595e C: #Ifs= 9 Cfg#= 1 Atr=e0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=88(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=8a(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=8b(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 6 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none) E: Ad=8c(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 7 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=70 Driver=(none) E: Ad=8d(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 8 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms 0x10b1: MBIM + tty (AT/NMEA) + tty (AT) + tty (AT) + tty (AT) + tty (diag) + DPL + QDSS (Qualcomm Debug SubSystem) + adb T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 8 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1bc7 ProdID=10b1 Rev=05.15 S: Manufacturer=Telit Cinterion S: Product=FE990 S: SerialNumber=28c2595e C: #Ifs=10 Cfg#= 1 Atr=e0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=32ms I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=88(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=8a(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=8b(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 7 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none) E: Ad=8c(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 8 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=70 Driver=(none) E: Ad=8d(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 9 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms 0x10b2: RNDIS + tty (AT/NMEA) + tty (AT) + tty (AT) + tty (AT) + tty (diag) + DPL + QDSS (Qualcomm Debug SubSystem) + adb T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 9 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1bc7 ProdID=10b2 Rev=05.15 S: Manufacturer=Telit Cinterion S: Product=FE990 S: SerialNumber=28c2595e C: #Ifs=10 Cfg#= 1 Atr=e0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 1 Cls=ef(misc ) Sub=04 Prot=01 Driver=rndis_host E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms I: If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=88(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=8a(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=8b(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 7 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none) E: Ad=8c(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 8 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=70 Driver=(none) E: Ad=8d(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 9 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms 0x10d3: ECM + tty (AT/NMEA) + tty (AT) + tty (AT) + tty (AT) + tty (diag) + DPL + QDSS (Qualcomm Debug SubSystem) + adb T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 11 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1bc7 ProdID=10b3 Rev=05.15 S: Manufacturer=Telit Cinterion S: Product=FE990 S: SerialNumber=28c2595e C: #Ifs=10 Cfg#= 1 Atr=e0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether E: Ad=82(I) Atr=03(Int.) MxPS= 16 Ivl=32ms I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=88(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=8a(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=8b(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 7 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none) E: Ad=8c(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 8 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=70 Driver=(none) E: Ad=8d(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 9 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms Cc: stable(a)vger.kernel.org Signed-off-by: Fabio Porcedda <fabio.porcedda(a)gmail.com> --- drivers/usb/serial/option.c | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index 58bd54e8c483..8660f7a89b01 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -1388,6 +1388,22 @@ static const struct usb_device_id option_ids[] = { .driver_info = RSVD(0) | NCTRL(2) | RSVD(3) | RSVD(4) }, { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x10aa, 0xff), /* Telit FN920C04 (MBIM) */ .driver_info = NCTRL(3) | RSVD(4) | RSVD(5) }, + { USB_DEVICE_INTERFACE_PROTOCOL(TELIT_VENDOR_ID, 0x10b0, 0x60) }, /* Telit FE990B (rmnet) */ + { USB_DEVICE_INTERFACE_PROTOCOL(TELIT_VENDOR_ID, 0x10b0, 0x40) }, + { USB_DEVICE_INTERFACE_PROTOCOL(TELIT_VENDOR_ID, 0x10b0, 0x30), + .driver_info = NCTRL(5) }, + { USB_DEVICE_INTERFACE_PROTOCOL(TELIT_VENDOR_ID, 0x10b1, 0x60) }, /* Telit FE990B (MBIM) */ + { USB_DEVICE_INTERFACE_PROTOCOL(TELIT_VENDOR_ID, 0x10b1, 0x40) }, + { USB_DEVICE_INTERFACE_PROTOCOL(TELIT_VENDOR_ID, 0x10b1, 0x30), + .driver_info = NCTRL(6) }, + { USB_DEVICE_INTERFACE_PROTOCOL(TELIT_VENDOR_ID, 0x10b2, 0x60) }, /* Telit FE990B (RNDIS) */ + { USB_DEVICE_INTERFACE_PROTOCOL(TELIT_VENDOR_ID, 0x10b2, 0x40) }, + { USB_DEVICE_INTERFACE_PROTOCOL(TELIT_VENDOR_ID, 0x10b2, 0x30), + .driver_info = NCTRL(6) }, + { USB_DEVICE_INTERFACE_PROTOCOL(TELIT_VENDOR_ID, 0x10b3, 0x60) }, /* Telit FE990B (ECM) */ + { USB_DEVICE_INTERFACE_PROTOCOL(TELIT_VENDOR_ID, 0x10b3, 0x40) }, + { USB_DEVICE_INTERFACE_PROTOCOL(TELIT_VENDOR_ID, 0x10b3, 0x30), + .driver_info = NCTRL(6) }, { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x10c0, 0xff), /* Telit FE910C04 (rmnet) */ .driver_info = RSVD(0) | NCTRL(3) }, { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x10c4, 0xff), /* Telit FE910C04 (rmnet) */ -- 2.48.1

6 months, 1 week

2
2
0 0

[tip: x86/urgent] x86/cacheinfo: Validate CPUID leaf 0x2 EDX output

by tip-bot2 for Ahmed S. Darwish

The following commit has been merged into the x86/urgent branch of tip: Commit-ID: 8177c6bedb7013cf736137da586cf783922309dd Gitweb: https://git.kernel.org/tip/8177c6bedb7013cf736137da586cf783922309dd Author: Ahmed S. Darwish <darwi(a)linutronix.de> AuthorDate: Tue, 04 Mar 2025 09:51:12 +01:00 Committer: Ingo Molnar <mingo(a)kernel.org> CommitterDate: Tue, 04 Mar 2025 09:59:14 +01:00 x86/cacheinfo: Validate CPUID leaf 0x2 EDX output CPUID leaf 0x2 emits one-byte descriptors in its four output registers EAX, EBX, ECX, and EDX. For these descriptors to be valid, the most significant bit (MSB) of each register must be clear. The historical Git commit: 019361a20f016 ("- pre6: Intel: start to add Pentium IV specific stuff (128-byte cacheline etc)...") introduced leaf 0x2 output parsing. It only validated the MSBs of EAX, EBX, and ECX, but left EDX unchecked. Validate EDX's most-significant bit. Signed-off-by: Ahmed S. Darwish <darwi(a)linutronix.de> Signed-off-by: Ingo Molnar <mingo(a)kernel.org> Cc: stable(a)vger.kernel.org Cc: "H. Peter Anvin" <hpa(a)zytor.com> Cc: Linus Torvalds <torvalds(a)linux-foundation.org> Link: https://lore.kernel.org/r/20250304085152.51092-2-darwi@linutronix.de --- arch/x86/kernel/cpu/cacheinfo.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/x86/kernel/cpu/cacheinfo.c b/arch/x86/kernel/cpu/cacheinfo.c index e6fa03e..a6c6bcc 100644 --- a/arch/x86/kernel/cpu/cacheinfo.c +++ b/arch/x86/kernel/cpu/cacheinfo.c @@ -808,7 +808,7 @@ void init_intel_cacheinfo(struct cpuinfo_x86 *c) cpuid(2, &regs[0], &regs[1], &regs[2], &regs[3]); /* If bit 31 is set, this is an unknown format */ - for (j = 0 ; j < 3 ; j++) + for (j = 0 ; j < 4 ; j++) if (regs[j] & (1 << 31)) regs[j] = 0;

6 months, 1 week

1
0
0 0

[PATCH V2 2/2] USB: serial: option: fix Telit Cinterion FE990A name

by Fabio Porcedda

The correct name for FE990 is FE990A so use it in order to avoid confusion with FE990B. Cc: stable(a)vger.kernel.org Signed-off-by: Fabio Porcedda <fabio.porcedda(a)gmail.com> --- drivers/usb/serial/option.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index 8660f7a89b01..c52d6a2146ff 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -1368,13 +1368,13 @@ static const struct usb_device_id option_ids[] = { .driver_info = NCTRL(0) | RSVD(1) }, { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1075, 0xff), /* Telit FN990A (PCIe) */ .driver_info = RSVD(0) }, - { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1080, 0xff), /* Telit FE990 (rmnet) */ + { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1080, 0xff), /* Telit FE990A (rmnet) */ .driver_info = NCTRL(0) | RSVD(1) | RSVD(2) }, - { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1081, 0xff), /* Telit FE990 (MBIM) */ + { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1081, 0xff), /* Telit FE990A (MBIM) */ .driver_info = NCTRL(0) | RSVD(1) }, - { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1082, 0xff), /* Telit FE990 (RNDIS) */ + { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1082, 0xff), /* Telit FE990A (RNDIS) */ .driver_info = NCTRL(2) | RSVD(3) }, - { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1083, 0xff), /* Telit FE990 (ECM) */ + { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1083, 0xff), /* Telit FE990A (ECM) */ .driver_info = NCTRL(0) | RSVD(1) }, { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x10a0, 0xff), /* Telit FN20C04 (rmnet) */ .driver_info = RSVD(0) | NCTRL(3) }, -- 2.48.1

6 months, 1 week

1
0
0 0

[PATCH v3 0/3] leds: rgb: leds-qcom-lpg: PWM fixes

by Abel Vesa

The PWM allow configuring the PWM resolution from 8 bits PWM values up to 15 bits values, for the Hi-Res PWMs, and then either 6-bit or 9-bit for the normal PWMs. The current implementation loops through all possible resolutions (PWM sizes), for the PWM subtype, on top of the already existing process of determining the prediv, exponent and refclk. The first and second issues are related to capping the computed PWM value. The third issue is that it uses the wrong maximum possible PWM value for determining the best matched period. Fix all of them. Signed-off-by: Abel Vesa <abel.vesa(a)linaro.org> --- Changes in v3: - Added a new patch that fixes the normal PWMs, since they now support 6-bit resolution as well. Added it as first patch. - Re-worded the second patch. Included Bjorn's suggestion and R-b tag. - Link to v2: https://lore.kernel.org/r/20250226-leds-qcom-lpg-fix-max-pwm-on-hi-res-v2-0… Changes in v2: - Re-worded the commit to drop the details that are not important w.r.t. what the patch is fixing. - Added another patch which fixes the resolution used for determining best matched period and PWM config. - Link to v1: https://lore.kernel.org/r/20250220-leds-qcom-lpg-fix-max-pwm-on-hi-res-v1-1… --- Abel Vesa (3): leds: rgb: leds-qcom-lpg: Fix pwm resolution max for normal PWMs leds: rgb: leds-qcom-lpg: Fix pwm resolution max for Hi-Res PWMs leds: rgb: leds-qcom-lpg: Fix calculation of best period Hi-Res PWMs drivers/leds/rgb/leds-qcom-lpg.c | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-) --- base-commit: cd3215bbcb9d4321def93fea6cfad4d5b42b9d1d change-id: 20250220-leds-qcom-lpg-fix-max-pwm-on-hi-res-067e8782a79b Best regards, -- Abel Vesa <abel.vesa(a)linaro.org>

6 months, 1 week

3
6
0 0

[PATCH net 1/2] net: phy: nxp-c45-tja11xx: add TJA112X PHY configuration errata

by Andrei Botila

The most recent sillicon versions of TJA1120 and TJA1121 can achieve full silicon performance by putting the PHY in managed mode. It is necessary to apply these PHY writes before link gets established. Application of this fix is required after restart of device and wakeup from sleep. Cc: stable(a)vger.kernel.org Fixes: f1fe5dff2b8a ("net: phy: nxp-c45-tja11xx: add TJA1120 support") Signed-off-by: Andrei Botila <andrei.botila(a)oss.nxp.com> --- drivers/net/phy/nxp-c45-tja11xx.c | 52 +++++++++++++++++++++++++++++++ 1 file changed, 52 insertions(+) diff --git a/drivers/net/phy/nxp-c45-tja11xx.c b/drivers/net/phy/nxp-c45-tja11xx.c index 34231b5b9175..e083b1a714fd 100644 --- a/drivers/net/phy/nxp-c45-tja11xx.c +++ b/drivers/net/phy/nxp-c45-tja11xx.c @@ -22,6 +22,11 @@ #define PHY_ID_TJA_1103 0x001BB010 #define PHY_ID_TJA_1120 0x001BB031 +#define VEND1_DEVICE_ID3 0x0004 +#define TJA1120_DEV_ID3_SILICON_VERSION GENMASK(15, 12) +#define TJA1120_DEV_ID3_SAMPLE_TYPE GENMASK(11, 8) +#define DEVICE_ID3_SAMPLE_TYPE_R 0x9 + #define VEND1_DEVICE_CONTROL 0x0040 #define DEVICE_CONTROL_RESET BIT(15) #define DEVICE_CONTROL_CONFIG_GLOBAL_EN BIT(14) @@ -1593,6 +1598,50 @@ static int nxp_c45_set_phy_mode(struct phy_device *phydev) return 0; } +/* Errata: ES_TJA1120 and ES_TJA1121 Rev. 1.0 — 28 November 2024 Section 3.1 */ +static void nxp_c45_tja1120_errata(struct phy_device *phydev) +{ + int silicon_version, sample_type; + bool macsec_ability; + int phy_abilities; + int ret = 0; + + ret = phy_read_mmd(phydev, MDIO_MMD_VEND1, VEND1_DEVICE_ID3); + if (ret < 0) + return; + + sample_type = FIELD_GET(TJA1120_DEV_ID3_SAMPLE_TYPE, ret); + if (sample_type != DEVICE_ID3_SAMPLE_TYPE_R) + return; + + silicon_version = FIELD_GET(TJA1120_DEV_ID3_SILICON_VERSION, ret); + + phy_abilities = phy_read_mmd(phydev, MDIO_MMD_VEND1, + VEND1_PORT_ABILITIES); + macsec_ability = !!(phy_abilities & MACSEC_ABILITY); + if ((!macsec_ability && silicon_version == 2) || + (macsec_ability && silicon_version == 1)) { + /* TJA1120/TJA1121 PHY configuration errata workaround. + * Apply PHY writes sequence before link up. + */ + if (!macsec_ability) { + phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x01F8, 0x4b95); + phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x01F9, 0xf3cd); + } else { + phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x01F8, 0x89c7); + phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x01F9, 0x0893); + } + + phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x0476, 0x58a0); + + phy_write_mmd(phydev, MDIO_MMD_PMAPMD, 0x8921, 0xa3a); + phy_write_mmd(phydev, MDIO_MMD_PMAPMD, 0x89F1, 0x16c1); + + phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x01F8, 0x0); + phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x01F9, 0x0); + } +} + static int nxp_c45_config_init(struct phy_device *phydev) { int ret; @@ -1609,6 +1658,9 @@ static int nxp_c45_config_init(struct phy_device *phydev) phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x01F8, 1); phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x01F9, 2); + if (phydev->drv->phy_id == PHY_ID_TJA_1120) + nxp_c45_tja1120_errata(phydev); + phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, VEND1_PHY_CONFIG, PHY_CONFIG_AUTO); -- 2.48.1

6 months, 1 week

1
1
0 0

[PATCH] reset: rzg2l-usbphy-ctrl: Correct reset status check

by Prabhakar

From: Lad Prabhakar <prabhakar.mahadev-lad.rj(a)bp.renesas.com> Ensure the reset status check explicitly evaluates whether all bits in `port_mask` are set. Replace the double negation (`!!`) with an equality check to prevent incorrect interpretation of partial bit matches as an asserted reset. Fixes: bee08559701f ("reset: renesas: Add RZ/G2L usbphy control driver") Cc: stable(a)vger.kernel.org Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj(a)bp.renesas.com> --- drivers/reset/reset-rzg2l-usbphy-ctrl.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/reset/reset-rzg2l-usbphy-ctrl.c b/drivers/reset/reset-rzg2l-usbphy-ctrl.c index 8a7f167e405e..6451f621e862 100644 --- a/drivers/reset/reset-rzg2l-usbphy-ctrl.c +++ b/drivers/reset/reset-rzg2l-usbphy-ctrl.c @@ -88,7 +88,7 @@ static int rzg2l_usbphy_ctrl_status(struct reset_controller_dev *rcdev, port_mask = id ? PHY_RESET_PORT2 : PHY_RESET_PORT1; - return !!(readl(priv->base + RESET) & port_mask); + return (readl(priv->base + RESET) & port_mask) == port_mask; } static const struct of_device_id rzg2l_usbphy_ctrl_match_table[] = { -- 2.43.0

6 months, 1 week

3
2
0 0

[PATCH v8] arm64: mm: Populate vmemmap at the page level if not section aligned

by Zhenhua Huang

On the arm64 platform with 4K base page config, SECTION_SIZE_BITS is set to 27, making one section 128M. The related page struct which vmemmap points to is 2M then. Commit c1cc1552616d ("arm64: MMU initialisation") optimizes the vmemmap to populate at the PMD section level which was suitable initially since hot plug granule is always one section(128M). However, commit ba72b4c8cf60 ("mm/sparsemem: support sub-section hotplug") introduced a 2M(SUBSECTION_SIZE) hot plug granule, which disrupted the existing arm64 assumptions. The first problem is that if start or end is not aligned to a section boundary, such as when a subsection is hot added, populating the entire section is wasteful. The next problem is if we hotplug something that spans part of 128 MiB section (subsections, let's call it memblock1), and then hotplug something that spans another part of a 128 MiB section(subsections, let's call it memblock2), and subsequently unplug memblock1, vmemmap_free() will clear the entire PMD entry which also supports memblock2 even though memblock2 is still active. Assuming hotplug/unplug sizes are guaranteed to be symmetric. Do the fix similar to x86-64: populate to pages levels if start/end is not aligned with section boundary. Cc: <stable(a)vger.kernel.org> # v5.4+ Fixes: ba72b4c8cf60 ("mm/sparsemem: support sub-section hotplug") Signed-off-by: Zhenhua Huang <quic_zhenhuah(a)quicinc.com> --- Hi Catalin and David, Following our latest discussion, I've updated the patch for your review. I also removed Catalin's review tag since I've made significant modifications. arch/arm64/mm/mmu.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/arch/arm64/mm/mmu.c b/arch/arm64/mm/mmu.c index b4df5bc5b1b8..de05ccf47f21 100644 --- a/arch/arm64/mm/mmu.c +++ b/arch/arm64/mm/mmu.c @@ -1177,8 +1177,11 @@ int __meminit vmemmap_populate(unsigned long start, unsigned long end, int node, struct vmem_altmap *altmap) { WARN_ON((start < VMEMMAP_START) || (end > VMEMMAP_END)); + /* [start, end] should be within one section */ + WARN_ON(end - start > PAGES_PER_SECTION * sizeof(struct page)); - if (!IS_ENABLED(CONFIG_ARM64_4K_PAGES)) + if (!IS_ENABLED(CONFIG_ARM64_4K_PAGES) || + (end - start < PAGES_PER_SECTION * sizeof(struct page))) return vmemmap_populate_basepages(start, end, node, altmap); else return vmemmap_populate_hugepages(start, end, node, altmap); -- 2.25.1

6 months, 1 week

2
2
0 0

[PATCH v2 4/6] wifi: mt76: mt7925: remove unused acpi function for clc

by Mingyen Hsieh

From: Ming Yen Hsieh <mingyen.hsieh(a)mediatek.com> The code for handling ACPI configuration in CLC was copied from the mt7921 driver but is not utilized in the mt7925 implementation. So removes the unused functionality to clean up the codebase. Cc: stable(a)vger.kernel.org Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips") Signed-off-by: Ming Yen Hsieh <mingyen.hsieh(a)mediatek.com> --- v2: no change --- drivers/net/wireless/mediatek/mt76/mt7925/mcu.c | 1 - 1 file changed, 1 deletion(-) diff --git a/drivers/net/wireless/mediatek/mt76/mt7925/mcu.c b/drivers/net/wireless/mediatek/mt76/mt7925/mcu.c index 602ac3c31976..3fd75216889f 100644 --- a/drivers/net/wireless/mediatek/mt76/mt7925/mcu.c +++ b/drivers/net/wireless/mediatek/mt76/mt7925/mcu.c @@ -3421,7 +3421,6 @@ __mt7925_mcu_set_clc(struct mt792x_dev *dev, u8 *alpha2, .idx = idx, .env = env_cap, - .acpi_conf = mt792x_acpi_get_flags(&dev->phy), }; int ret, valid_cnt = 0; u8 *pos, *last_pos; -- 2.34.1

6 months, 1 week

1
0
0 0

[PATCH] usb: dwc3: Set SUSPENDENABLE soon after phy init

by Thinh Nguyen

After phy initialization, some phy operations can only be executed while in lower P states. Ensure GUSB3PIPECTL.SUSPENDENABLE and GUSB2PHYCFG.SUSPHY are set soon after initialization to avoid blocking phy ops. Previously the SUSPENDENABLE bits are only set after the controller initialization, which may not happen right away if there's no gadget driver or xhci driver bound. Revise this to clear SUSPENDENABLE bits only when there's mode switching (change in GCTL.PRTCAPDIR). Fixes: 6d735722063a ("usb: dwc3: core: Prevent phy suspend during init") Cc: stable(a)vger.kernel.org Signed-off-by: Thinh Nguyen <Thinh.Nguyen(a)synopsys.com> --- drivers/usb/dwc3/core.c | 69 +++++++++++++++++++++++++---------------- drivers/usb/dwc3/core.h | 2 +- drivers/usb/dwc3/drd.c | 4 +-- 3 files changed, 45 insertions(+), 30 deletions(-) diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c index dfa1b5fe48dc..87b4c04a868c 100644 --- a/drivers/usb/dwc3/core.c +++ b/drivers/usb/dwc3/core.c @@ -131,11 +131,24 @@ void dwc3_enable_susphy(struct dwc3 *dwc, bool enable) } } -void dwc3_set_prtcap(struct dwc3 *dwc, u32 mode) +void dwc3_set_prtcap(struct dwc3 *dwc, u32 mode, bool ignore_susphy) { + unsigned int hw_mode; u32 reg; reg = dwc3_readl(dwc->regs, DWC3_GCTL); + + /* + * For DRD controllers, GUSB3PIPECTL.SUSPENDENABLE and + * GUSB2PHYCFG.SUSPHY should be cleared during mode switching, + * and they can be set after core initialization. + */ + hw_mode = DWC3_GHWPARAMS0_MODE(dwc->hwparams.hwparams0); + if (hw_mode == DWC3_GHWPARAMS0_MODE_DRD && !ignore_susphy) { + if (DWC3_GCTL_PRTCAP(reg) != mode) + dwc3_enable_susphy(dwc, false); + } + reg &= ~(DWC3_GCTL_PRTCAPDIR(DWC3_GCTL_PRTCAP_OTG)); reg |= DWC3_GCTL_PRTCAPDIR(mode); dwc3_writel(dwc->regs, DWC3_GCTL, reg); @@ -216,7 +229,7 @@ static void __dwc3_set_mode(struct work_struct *work) spin_lock_irqsave(&dwc->lock, flags); - dwc3_set_prtcap(dwc, desired_dr_role); + dwc3_set_prtcap(dwc, desired_dr_role, false); spin_unlock_irqrestore(&dwc->lock, flags); @@ -658,16 +671,7 @@ static int dwc3_ss_phy_setup(struct dwc3 *dwc, int index) */ reg &= ~DWC3_GUSB3PIPECTL_UX_EXIT_PX; - /* - * Above DWC_usb3.0 1.94a, it is recommended to set - * DWC3_GUSB3PIPECTL_SUSPHY to '0' during coreConsultant configuration. - * So default value will be '0' when the core is reset. Application - * needs to set it to '1' after the core initialization is completed. - * - * Similarly for DRD controllers, GUSB3PIPECTL.SUSPENDENABLE must be - * cleared after power-on reset, and it can be set after core - * initialization. - */ + /* Ensure the GUSB3PIPECTL.SUSPENDENABLE is cleared prior to phy init. */ reg &= ~DWC3_GUSB3PIPECTL_SUSPHY; if (dwc->u2ss_inp3_quirk) @@ -747,15 +751,7 @@ static int dwc3_hs_phy_setup(struct dwc3 *dwc, int index) break; } - /* - * Above DWC_usb3.0 1.94a, it is recommended to set - * DWC3_GUSB2PHYCFG_SUSPHY to '0' during coreConsultant configuration. - * So default value will be '0' when the core is reset. Application - * needs to set it to '1' after the core initialization is completed. - * - * Similarly for DRD controllers, GUSB2PHYCFG.SUSPHY must be cleared - * after power-on reset, and it can be set after core initialization. - */ + /* Ensure the GUSB2PHYCFG.SUSPHY is cleared prior to phy init. */ reg &= ~DWC3_GUSB2PHYCFG_SUSPHY; if (dwc->dis_enblslpm_quirk) @@ -830,6 +826,25 @@ static int dwc3_phy_init(struct dwc3 *dwc) goto err_exit_usb3_phy; } + /* + * Above DWC_usb3.0 1.94a, it is recommended to set + * DWC3_GUSB3PIPECTL_SUSPHY and DWC3_GUSB2PHYCFG_SUSPHY to '0' during + * coreConsultant configuration. So default value will be '0' when the + * core is reset. Application needs to set it to '1' after the core + * initialization is completed. + * + * Certain phy requires to be in P0 power state during initialization. + * Make sure GUSB3PIPECTL.SUSPENDENABLE and GUSB2PHYCFG.SUSPHY are clear + * prior to phy init to maintain in the P0 state. + * + * After phy initialization, some phy operations can only be executed + * while in lower P states. Ensure GUSB3PIPECTL.SUSPENDENABLE and + * GUSB2PHYCFG.SUSPHY are set soon after initialization to avoid + * blocking phy ops. + */ + if (!DWC3_VER_IS_WITHIN(DWC3, ANY, 194A)) + dwc3_enable_susphy(dwc, true); + return 0; err_exit_usb3_phy: @@ -1588,7 +1603,7 @@ static int dwc3_core_init_mode(struct dwc3 *dwc) switch (dwc->dr_mode) { case USB_DR_MODE_PERIPHERAL: - dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_DEVICE); + dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_DEVICE, false); if (dwc->usb2_phy) otg_set_vbus(dwc->usb2_phy->otg, false); @@ -1600,7 +1615,7 @@ static int dwc3_core_init_mode(struct dwc3 *dwc) return dev_err_probe(dev, ret, "failed to initialize gadget\n"); break; case USB_DR_MODE_HOST: - dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_HOST); + dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_HOST, false); if (dwc->usb2_phy) otg_set_vbus(dwc->usb2_phy->otg, true); @@ -1645,7 +1660,7 @@ static void dwc3_core_exit_mode(struct dwc3 *dwc) } /* de-assert DRVVBUS for HOST and OTG mode */ - dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_DEVICE); + dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_DEVICE, true); } static void dwc3_get_software_properties(struct dwc3 *dwc) @@ -2457,7 +2472,7 @@ static int dwc3_resume_common(struct dwc3 *dwc, pm_message_t msg) if (ret) return ret; - dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_DEVICE); + dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_DEVICE, true); dwc3_gadget_resume(dwc); break; case DWC3_GCTL_PRTCAP_HOST: @@ -2465,7 +2480,7 @@ static int dwc3_resume_common(struct dwc3 *dwc, pm_message_t msg) ret = dwc3_core_init_for_resume(dwc); if (ret) return ret; - dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_HOST); + dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_HOST, true); break; } /* Restore GUSB2PHYCFG bits that were modified in suspend */ @@ -2494,7 +2509,7 @@ static int dwc3_resume_common(struct dwc3 *dwc, pm_message_t msg) if (ret) return ret; - dwc3_set_prtcap(dwc, dwc->current_dr_role); + dwc3_set_prtcap(dwc, dwc->current_dr_role, true); dwc3_otg_init(dwc); if (dwc->current_otg_role == DWC3_OTG_ROLE_HOST) { diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h index ac7c730f81ac..19ad5b6e1ede 100644 --- a/drivers/usb/dwc3/core.h +++ b/drivers/usb/dwc3/core.h @@ -1557,7 +1557,7 @@ struct dwc3_gadget_ep_cmd_params { #define DWC3_HAS_OTG BIT(3) /* prototypes */ -void dwc3_set_prtcap(struct dwc3 *dwc, u32 mode); +void dwc3_set_prtcap(struct dwc3 *dwc, u32 mode, bool ignore_susphy); void dwc3_set_mode(struct dwc3 *dwc, u32 mode); u32 dwc3_core_fifo_space(struct dwc3_ep *dep, u8 type); diff --git a/drivers/usb/dwc3/drd.c b/drivers/usb/dwc3/drd.c index d76ae676783c..7977860932b1 100644 --- a/drivers/usb/dwc3/drd.c +++ b/drivers/usb/dwc3/drd.c @@ -173,7 +173,7 @@ void dwc3_otg_init(struct dwc3 *dwc) * block "Initialize GCTL for OTG operation". */ /* GCTL.PrtCapDir=2'b11 */ - dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_OTG); + dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_OTG, true); /* GUSB2PHYCFG0.SusPHY=0 */ reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0)); reg &= ~DWC3_GUSB2PHYCFG_SUSPHY; @@ -556,7 +556,7 @@ int dwc3_drd_init(struct dwc3 *dwc) dwc3_drd_update(dwc); } else { - dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_OTG); + dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_OTG, true); /* use OTG block to get ID event */ irq = dwc3_otg_get_irq(dwc); base-commit: 72deda0abee6e705ae71a93f69f55e33be5bca5c -- 2.28.0

6 months, 1 week

2
2
0 0

2025

2024

2023

2022

2021

2020

2019

2018

2017

Linux-stable-mirror March 2025