Rockchip platforms use 'GPIO_ACTIVE_HIGH' flag in the devicetree definition
for ep_gpio. This means, whatever the logical value set by the driver for
the ep_gpio, physical line will output the same logic level.
For instance,
gpiod_set_value_cansleep(rockchip->ep_gpio, 0); --> Level low
gpiod_set_value_cansleep(rockchip->ep_gpio, 1); --> Level high
But while requesting the ep_gpio, GPIOD_OUT_HIGH flag is currently used.
Now, this also causes the physical line to output 'high' creating trouble
for endpoint devices during host reboot.
When host reboot happens, the ep_gpio will initially output 'low' due to
the GPIO getting reset to its POR value. Then during host controller probe,
it will output 'high' due to GPIOD_OUT_HIGH flag. Then during
rockchip_pcie_host_init_port(), it will first output 'low' and then 'high'
indicating the completion of controller initialization.
On the endpoint side, each output 'low' of ep_gpio is accounted for PERST#
assert and 'high' for PERST# deassert. With the above mentioned flow during
host reboot, endpoint will witness below state changes for PERST#:
(1) PERST# assert - GPIO POR state
(2) PERST# deassert - GPIOD_OUT_HIGH while requesting GPIO
(3) PERST# assert - rockchip_pcie_host_init_port()
(4) PERST# deassert - rockchip_pcie_host_init_port()
Now the time interval between (2) and (3) is very short as both happen
during the driver probe(), and this results in a race in the endpoint.
Because, before completing the PERST# deassertion in (2), endpoint got
another PERST# assert in (3).
A proper way to fix this issue is to change the GPIOD_OUT_HIGH flag in (2)
to GPIOD_OUT_LOW. Because the usual convention is to request the GPIO with
a state corresponding to its 'initial/default' value and let the driver
change the state of the GPIO when required.
As per that, the ep_gpio should be requested with GPIOD_OUT_LOW as it
corresponds to the POR value of '0' (PERST# assert in the endpoint). Then
the driver can change the state of the ep_gpio later in
rockchip_pcie_host_init_port() as per the initialization sequence.
This fixes the firmware crash issue in Qcom based modems connected to
Rockpro64 based board.
Cc: <stable(a)vger.kernel.org> # 4.9
Reported-by: Slark Xiao <slark_xiao(a)163.com>
Closes: https://lore.kernel.org/mhi/20240402045647.GG2933@thinkpad/
Fixes: e77f847df54c ("PCI: rockchip: Add Rockchip PCIe controller support")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam(a)linaro.org>
---
drivers/pci/controller/pcie-rockchip.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/pci/controller/pcie-rockchip.c b/drivers/pci/controller/pcie-rockchip.c
index 0ef2e622d36e..c07d7129f1c7 100644
--- a/drivers/pci/controller/pcie-rockchip.c
+++ b/drivers/pci/controller/pcie-rockchip.c
@@ -121,7 +121,7 @@ int rockchip_pcie_parse_dt(struct rockchip_pcie *rockchip)
if (rockchip->is_rc) {
rockchip->ep_gpio = devm_gpiod_get_optional(dev, "ep",
- GPIOD_OUT_HIGH);
+ GPIOD_OUT_LOW);
if (IS_ERR(rockchip->ep_gpio))
return dev_err_probe(dev, PTR_ERR(rockchip->ep_gpio),
"failed to get ep GPIO\n");
---
base-commit: 4cece764965020c22cff7665b18a012006359095
change-id: 20240416-pci-rockchip-perst-fix-88c922621d9a
Best regards,
--
Manivannan Sadhasivam <manivannan.sadhasivam(a)linaro.org>
Remove wrong mask on subsys_vendor_id. Both the Vendor ID and Subsystem
Vendor ID are u16 variables and are written to a u32 register of the
controller. The Subsystem Vendor ID was always 0 because the u16 value
was masked incorrectly with GENMASK(31,16) resulting in all lower 16
bits being set to 0 prior to the shift.
Remove both masks as they are unnecessary and set the register correctly
i.e., the lower 16-bits are the Vendor ID and the upper 16-bits are the
Subsystem Vendor ID.
This is documented in the RK3399 TRM section 17.6.7.1.17
Fixes: cf590b078391 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Signed-off-by: Rick Wertenbroek <rick.wertenbroek(a)gmail.com>
Cc: stable(a)vger.kernel.org
---
drivers/pci/controller/pcie-rockchip-ep.c | 7 +++----
1 file changed, 3 insertions(+), 4 deletions(-)
diff --git a/drivers/pci/controller/pcie-rockchip-ep.c b/drivers/pci/controller/pcie-rockchip-ep.c
index c9046e97a1d2..37d4bcb8bd5b 100644
--- a/drivers/pci/controller/pcie-rockchip-ep.c
+++ b/drivers/pci/controller/pcie-rockchip-ep.c
@@ -98,10 +98,9 @@ static int rockchip_pcie_ep_write_header(struct pci_epc *epc, u8 fn, u8 vfn,
/* All functions share the same vendor ID with function 0 */
if (fn == 0) {
- u32 vid_regs = (hdr->vendorid & GENMASK(15, 0)) |
- (hdr->subsys_vendor_id & GENMASK(31, 16)) << 16;
-
- rockchip_pcie_write(rockchip, vid_regs,
+ rockchip_pcie_write(rockchip,
+ hdr->vendorid |
+ hdr->subsys_vendor_id << 16,
PCIE_CORE_CONFIG_VENDOR);
}
--
2.25.1
Commit 35039eb6b199 ("x86: Show symbol name if insn decoder test failed")
included symbol lines in the post-processed objdump output consumed by
the insn decoder test. This broke the `instuction lines == total lines`
property that `insn_decoder_test.c` relied upon to print the offending
line's number in error messages. This has the consequence that the line
number reported on a test failure is unreated to, and much smaller than,
the line that actually caused the problem.
Add a new variable that counts the combined (insn+symbol) line count and
report this in the error message.
Fixes: 35039eb6b199 ("x86: Show symbol name if insn decoder test failed")
Cc: stable(a)vger.kernel.org
Reviewed-by: Miguel Ojeda <ojeda(a)kernel.org>
Tested-by: Miguel Ojeda <ojeda(a)kernel.org>
Reported-by: John Baublitz <john.m.baublitz(a)gmail.com>
Debugged-by: John Baublitz <john.m.baublitz(a)gmail.com>
Signed-off-by: Valentin Obst <kernel(a)valentinobst.de>
---
See v2's commit message and [1] for context why this bug made debugging a
test failure harder than necessary.
[1]: https://rust-for-linux.zulipchat.com/#narrow/stream/291565-Help/topic/insn_…
Changes in v3:
- Add Cc stable tag in sign-off area.
- Make commit message less verbose.
- Link to v2: https://lore.kernel.org/r/20240223-x86-insn-decoder-line-fix-v2-1-cde49c69f…
Changes in v2:
- Added tags 'Reviewed-by', 'Tested-by', 'Reported-by', 'Debugged-by',
'Link', and 'Fixes'.
- Explain why this patch fixes the commit mentioned in the 'Fixes' tag.
- CCed the stable list and sent to all x86 maintainers.
- Link to v1: https://lore.kernel.org/r/20240221-x86-insn-decoder-line-fix-v1-1-47cd5a171…
---
arch/x86/tools/insn_decoder_test.c | 7 +++++--
1 file changed, 5 insertions(+), 2 deletions(-)
diff --git a/arch/x86/tools/insn_decoder_test.c b/arch/x86/tools/insn_decoder_test.c
index 472540aeabc2..727017a3c3c7 100644
--- a/arch/x86/tools/insn_decoder_test.c
+++ b/arch/x86/tools/insn_decoder_test.c
@@ -114,6 +114,7 @@ int main(int argc, char **argv)
unsigned char insn_buff[16];
struct insn insn;
int insns = 0;
+ int lines = 0;
int warnings = 0;
parse_args(argc, argv);
@@ -123,6 +124,8 @@ int main(int argc, char **argv)
int nb = 0, ret;
unsigned int b;
+ lines++;
+
if (line[0] == '<') {
/* Symbol line */
strcpy(sym, line);
@@ -134,12 +137,12 @@ int main(int argc, char **argv)
strcpy(copy, line);
tab1 = strchr(copy, '\t');
if (!tab1)
- malformed_line(line, insns);
+ malformed_line(line, lines);
s = tab1 + 1;
s += strspn(s, " ");
tab2 = strchr(s, '\t');
if (!tab2)
- malformed_line(line, insns);
+ malformed_line(line, lines);
*tab2 = '\0'; /* Characters beyond tab2 aren't examined */
while (s < tab2) {
if (sscanf(s, "%x", &b) == 1) {
---
base-commit: 4cece764965020c22cff7665b18a012006359095
change-id: 20240221-x86-insn-decoder-line-fix-7b1f2e1732ff
Best regards,
--
Valentin Obst <kernel(a)valentinobst.de>
The patch below does not apply to the 6.1-stable tree.
If someone wants it applied there, or to any other stable or longterm
tree, then please email the backport, including the original git commit
id to <stable(a)vger.kernel.org>.
To reproduce the conflict and resubmit, you may use the following commands:
git fetch https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/ linux-6.1.y
git checkout FETCH_HEAD
git cherry-pick -x 07a57a338adb6ec9e766d6a6790f76527f45ceb5
# <resolve conflicts, build, test, etc.>
git commit -s
git send-email --to '<stable(a)vger.kernel.org>' --in-reply-to '2024042309-rural-overlying-190b@gregkh' --subject-prefix 'PATCH 6.1.y' HEAD^..
Possible dependencies:
07a57a338adb ("mm,swapops: update check in is_pfn_swap_entry for hwpoison entries")
d027122d8363 ("mm/hwpoison: move definitions of num_poisoned_pages_* to memory-failure.c")
e591ef7d96d6 ("mm,hwpoison,hugetlb,memory_hotplug: hotremove memory section with hwpoisoned hugepage")
thanks,
greg k-h
------------------ original commit in Linus's tree ------------------
From 07a57a338adb6ec9e766d6a6790f76527f45ceb5 Mon Sep 17 00:00:00 2001
From: Oscar Salvador <osalvador(a)suse.de>
Date: Sun, 7 Apr 2024 15:05:37 +0200
Subject: [PATCH] mm,swapops: update check in is_pfn_swap_entry for hwpoison
entries
Tony reported that the Machine check recovery was broken in v6.9-rc1, as
he was hitting a VM_BUG_ON when injecting uncorrectable memory errors to
DRAM.
After some more digging and debugging on his side, he realized that this
went back to v6.1, with the introduction of 'commit 0d206b5d2e0d
("mm/swap: add swp_offset_pfn() to fetch PFN from swap entry")'. That
commit, among other things, introduced swp_offset_pfn(), replacing
hwpoison_entry_to_pfn() in its favour.
The patch also introduced a VM_BUG_ON() check for is_pfn_swap_entry(), but
is_pfn_swap_entry() never got updated to cover hwpoison entries, which
means that we would hit the VM_BUG_ON whenever we would call
swp_offset_pfn() for such entries on environments with CONFIG_DEBUG_VM
set. Fix this by updating the check to cover hwpoison entries as well,
and update the comment while we are it.
Link: https://lkml.kernel.org/r/20240407130537.16977-1-osalvador@suse.de
Fixes: 0d206b5d2e0d ("mm/swap: add swp_offset_pfn() to fetch PFN from swap entry")
Signed-off-by: Oscar Salvador <osalvador(a)suse.de>
Reported-by: Tony Luck <tony.luck(a)intel.com>
Closes: https://lore.kernel.org/all/Zg8kLSl2yAlA3o5D@agluck-desk3/
Tested-by: Tony Luck <tony.luck(a)intel.com>
Reviewed-by: Peter Xu <peterx(a)redhat.com>
Reviewed-by: David Hildenbrand <david(a)redhat.com>
Acked-by: Miaohe Lin <linmiaohe(a)huawei.com>
Cc: <stable(a)vger.kernel.org> [6.1.x]
Signed-off-by: Andrew Morton <akpm(a)linux-foundation.org>
diff --git a/include/linux/swapops.h b/include/linux/swapops.h
index 48b700ba1d18..a5c560a2f8c2 100644
--- a/include/linux/swapops.h
+++ b/include/linux/swapops.h
@@ -390,6 +390,35 @@ static inline bool is_migration_entry_dirty(swp_entry_t entry)
}
#endif /* CONFIG_MIGRATION */
+#ifdef CONFIG_MEMORY_FAILURE
+
+/*
+ * Support for hardware poisoned pages
+ */
+static inline swp_entry_t make_hwpoison_entry(struct page *page)
+{
+ BUG_ON(!PageLocked(page));
+ return swp_entry(SWP_HWPOISON, page_to_pfn(page));
+}
+
+static inline int is_hwpoison_entry(swp_entry_t entry)
+{
+ return swp_type(entry) == SWP_HWPOISON;
+}
+
+#else
+
+static inline swp_entry_t make_hwpoison_entry(struct page *page)
+{
+ return swp_entry(0, 0);
+}
+
+static inline int is_hwpoison_entry(swp_entry_t swp)
+{
+ return 0;
+}
+#endif
+
typedef unsigned long pte_marker;
#define PTE_MARKER_UFFD_WP BIT(0)
@@ -483,8 +512,9 @@ static inline struct folio *pfn_swap_entry_folio(swp_entry_t entry)
/*
* A pfn swap entry is a special type of swap entry that always has a pfn stored
- * in the swap offset. They are used to represent unaddressable device memory
- * and to restrict access to a page undergoing migration.
+ * in the swap offset. They can either be used to represent unaddressable device
+ * memory, to restrict access to a page undergoing migration or to represent a
+ * pfn which has been hwpoisoned and unmapped.
*/
static inline bool is_pfn_swap_entry(swp_entry_t entry)
{
@@ -492,7 +522,7 @@ static inline bool is_pfn_swap_entry(swp_entry_t entry)
BUILD_BUG_ON(SWP_TYPE_SHIFT < SWP_PFN_BITS);
return is_migration_entry(entry) || is_device_private_entry(entry) ||
- is_device_exclusive_entry(entry);
+ is_device_exclusive_entry(entry) || is_hwpoison_entry(entry);
}
struct page_vma_mapped_walk;
@@ -561,35 +591,6 @@ static inline int is_pmd_migration_entry(pmd_t pmd)
}
#endif /* CONFIG_ARCH_ENABLE_THP_MIGRATION */
-#ifdef CONFIG_MEMORY_FAILURE
-
-/*
- * Support for hardware poisoned pages
- */
-static inline swp_entry_t make_hwpoison_entry(struct page *page)
-{
- BUG_ON(!PageLocked(page));
- return swp_entry(SWP_HWPOISON, page_to_pfn(page));
-}
-
-static inline int is_hwpoison_entry(swp_entry_t entry)
-{
- return swp_type(entry) == SWP_HWPOISON;
-}
-
-#else
-
-static inline swp_entry_t make_hwpoison_entry(struct page *page)
-{
- return swp_entry(0, 0);
-}
-
-static inline int is_hwpoison_entry(swp_entry_t swp)
-{
- return 0;
-}
-#endif
-
static inline int non_swap_entry(swp_entry_t entry)
{
return swp_type(entry) >= MAX_SWAPFILES;
From: Mark Brown <broonie(a)kernel.org>
[ Upstream commit 907f33028871fa7c9a3db1efd467b78ef82cce20 ]
The standard library perror() function provides a convenient way to print
an error message based on the current errno but this doesn't play nicely
with KTAP output. Provide a helper which does an equivalent thing in a KTAP
compatible format.
nolibc doesn't have a strerror() and adding the table of strings required
doesn't seem like a good fit for what it's trying to do so when we're using
that only print the errno.
Signed-off-by: Mark Brown <broonie(a)kernel.org>
Reviewed-by: Kees Cook <keescook(a)chromium.org>
Signed-off-by: Shuah Khan <skhan(a)linuxfoundation.org>
Stable-dep-of: 071af0c9e582 ("selftests: timers: Convert posix_timers test to generate KTAP output")
Signed-off-by: Edward Liaw <edliaw(a)google.com>
---
tools/testing/selftests/kselftest.h | 14 ++++++++++++++
1 file changed, 14 insertions(+)
diff --git a/tools/testing/selftests/kselftest.h b/tools/testing/selftests/kselftest.h
index e8eecbc83a60..ad7b97e16f37 100644
--- a/tools/testing/selftests/kselftest.h
+++ b/tools/testing/selftests/kselftest.h
@@ -48,6 +48,7 @@
#include <stdlib.h>
#include <unistd.h>
#include <stdarg.h>
+#include <string.h>
#include <stdio.h>
#include <sys/utsname.h>
#endif
@@ -156,6 +157,19 @@ static inline void ksft_print_msg(const char *msg, ...)
va_end(args);
}
+static inline void ksft_perror(const char *msg)
+{
+#ifndef NOLIBC
+ ksft_print_msg("%s: %s (%d)\n", msg, strerror(errno), errno);
+#else
+ /*
+ * nolibc doesn't provide strerror() and it seems
+ * inappropriate to add one, just print the errno.
+ */
+ ksft_print_msg("%s: %d)\n", msg, errno);
+#endif
+}
+
static inline void ksft_test_result_pass(const char *msg, ...)
{
int saved_errno = errno;
--
2.44.0.769.g3c40516874-goog
Wire up LMH on QCM2290 and fix a bad bug while at it.
P1-2 for thermal, P3 for qcom
Signed-off-by: Konrad Dybcio <konrad.dybcio(a)linaro.org>
---
Changes in v2:
- Pick up tags
- Fix a couple typos in commit messages
- Drop stray msm8998 binding addition
- Link to v1: https://lore.kernel.org/r/20240308-topic-rb1_lmh-v1-0-50c60ffe1130@linaro.o…
---
Konrad Dybcio (2):
dt-bindings: thermal: lmh: Add QCM2290 compatible
thermal: qcom: lmh: Check for SCM availability at probe
Loic Poulain (1):
arm64: dts: qcom: qcm2290: Add LMH node
Documentation/devicetree/bindings/thermal/qcom-lmh.yaml | 12 ++++++++----
arch/arm64/boot/dts/qcom/qcm2290.dtsi | 14 +++++++++++++-
drivers/thermal/qcom/lmh.c | 3 +++
3 files changed, 24 insertions(+), 5 deletions(-)
---
base-commit: 8ffc8b1bbd505e27e2c8439d326b6059c906c9dd
change-id: 20240308-topic-rb1_lmh-1e0f440c392a
Best regards,
--
Konrad Dybcio <konrad.dybcio(a)linaro.org>
When reading EDID fails and driver reports no modes available, the DRM
core adds an artificial 1024x786 mode to the connector. Unfortunately
some variants of the Exynos HDMI (like the one in Exynos4 SoCs) are not
able to drive such mode, so report a safe 640x480 mode instead of nothing
in case of the EDID reading failure.
This fixes the following issue observed on Trats2 board since commit
13d5b040363c ("drm/exynos: do not return negative values from .get_modes()"):
[drm] Exynos DRM: using 11c00000.fimd device for DMA mapping operations
exynos-drm exynos-drm: bound 11c00000.fimd (ops fimd_component_ops)
exynos-drm exynos-drm: bound 12c10000.mixer (ops mixer_component_ops)
exynos-dsi 11c80000.dsi: [drm:samsung_dsim_host_attach] Attached s6e8aa0 device (lanes:4 bpp:24 mode-flags:0x10b)
exynos-drm exynos-drm: bound 11c80000.dsi (ops exynos_dsi_component_ops)
exynos-drm exynos-drm: bound 12d00000.hdmi (ops hdmi_component_ops)
[drm] Initialized exynos 1.1.0 20180330 for exynos-drm on minor 1
exynos-hdmi 12d00000.hdmi: [drm:hdmiphy_enable.part.0] *ERROR* PLL could not reach steady state
panel-samsung-s6e8aa0 11c80000.dsi.0: ID: 0xa2, 0x20, 0x8c
exynos-mixer 12c10000.mixer: timeout waiting for VSYNC
------------[ cut here ]------------
WARNING: CPU: 1 PID: 11 at drivers/gpu/drm/drm_atomic_helper.c:1682 drm_atomic_helper_wait_for_vblanks.part.0+0x2b0/0x2b8
[CRTC:70:crtc-1] vblank wait timed out
Modules linked in:
CPU: 1 PID: 11 Comm: kworker/u16:0 Not tainted 6.9.0-rc5-next-20240424 #14913
Hardware name: Samsung Exynos (Flattened Device Tree)
Workqueue: events_unbound deferred_probe_work_func
Call trace:
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x68/0x88
dump_stack_lvl from __warn+0x7c/0x1c4
__warn from warn_slowpath_fmt+0x11c/0x1a8
warn_slowpath_fmt from drm_atomic_helper_wait_for_vblanks.part.0+0x2b0/0x2b8
drm_atomic_helper_wait_for_vblanks.part.0 from drm_atomic_helper_commit_tail_rpm+0x7c/0x8c
drm_atomic_helper_commit_tail_rpm from commit_tail+0x9c/0x184
commit_tail from drm_atomic_helper_commit+0x168/0x190
drm_atomic_helper_commit from drm_atomic_commit+0xb4/0xe0
drm_atomic_commit from drm_client_modeset_commit_atomic+0x23c/0x27c
drm_client_modeset_commit_atomic from drm_client_modeset_commit_locked+0x60/0x1cc
drm_client_modeset_commit_locked from drm_client_modeset_commit+0x24/0x40
drm_client_modeset_commit from __drm_fb_helper_restore_fbdev_mode_unlocked+0x9c/0xc4
__drm_fb_helper_restore_fbdev_mode_unlocked from drm_fb_helper_set_par+0x2c/0x3c
drm_fb_helper_set_par from fbcon_init+0x3d8/0x550
fbcon_init from visual_init+0xc0/0x108
visual_init from do_bind_con_driver+0x1b8/0x3a4
do_bind_con_driver from do_take_over_console+0x140/0x1ec
do_take_over_console from do_fbcon_takeover+0x70/0xd0
do_fbcon_takeover from fbcon_fb_registered+0x19c/0x1ac
fbcon_fb_registered from register_framebuffer+0x190/0x21c
register_framebuffer from __drm_fb_helper_initial_config_and_unlock+0x350/0x574
__drm_fb_helper_initial_config_and_unlock from exynos_drm_fbdev_client_hotplug+0x6c/0xb0
exynos_drm_fbdev_client_hotplug from drm_client_register+0x58/0x94
drm_client_register from exynos_drm_bind+0x160/0x190
exynos_drm_bind from try_to_bring_up_aggregate_device+0x200/0x2d8
try_to_bring_up_aggregate_device from __component_add+0xb0/0x170
__component_add from mixer_probe+0x74/0xcc
mixer_probe from platform_probe+0x5c/0xb8
platform_probe from really_probe+0xe0/0x3d8
really_probe from __driver_probe_device+0x9c/0x1e4
__driver_probe_device from driver_probe_device+0x30/0xc0
driver_probe_device from __device_attach_driver+0xa8/0x120
__device_attach_driver from bus_for_each_drv+0x80/0xcc
bus_for_each_drv from __device_attach+0xac/0x1fc
__device_attach from bus_probe_device+0x8c/0x90
bus_probe_device from deferred_probe_work_func+0x98/0xe0
deferred_probe_work_func from process_one_work+0x240/0x6d0
process_one_work from worker_thread+0x1a0/0x3f4
worker_thread from kthread+0x104/0x138
kthread from ret_from_fork+0x14/0x28
Exception stack(0xf0895fb0 to 0xf0895ff8)
...
irq event stamp: 82357
hardirqs last enabled at (82363): [<c01a96e8>] vprintk_emit+0x308/0x33c
hardirqs last disabled at (82368): [<c01a969c>] vprintk_emit+0x2bc/0x33c
softirqs last enabled at (81614): [<c0101644>] __do_softirq+0x320/0x500
softirqs last disabled at (81609): [<c012dfe0>] __irq_exit_rcu+0x130/0x184
---[ end trace 0000000000000000 ]---
exynos-drm exynos-drm: [drm] *ERROR* flip_done timed out
exynos-drm exynos-drm: [drm] *ERROR* [CRTC:70:crtc-1] commit wait timed out
exynos-drm exynos-drm: [drm] *ERROR* flip_done timed out
exynos-drm exynos-drm: [drm] *ERROR* [CONNECTOR:74:HDMI-A-1] commit wait timed out
exynos-drm exynos-drm: [drm] *ERROR* flip_done timed out
exynos-drm exynos-drm: [drm] *ERROR* [PLANE:56:plane-5] commit wait timed out
exynos-mixer 12c10000.mixer: timeout waiting for VSYNC
Cc: stable(a)vger.kernel.org
Fixes: 13d5b040363c ("drm/exynos: do not return negative values from .get_modes()")
Signed-off-by: Marek Szyprowski <m.szyprowski(a)samsung.com>
---
drivers/gpu/drm/exynos/exynos_hdmi.c | 7 +++++--
1 file changed, 5 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/exynos/exynos_hdmi.c b/drivers/gpu/drm/exynos/exynos_hdmi.c
index 5fdeec8a3875..9d246db6ef2b 100644
--- a/drivers/gpu/drm/exynos/exynos_hdmi.c
+++ b/drivers/gpu/drm/exynos/exynos_hdmi.c
@@ -887,11 +887,11 @@ static int hdmi_get_modes(struct drm_connector *connector)
int ret;
if (!hdata->ddc_adpt)
- return 0;
+ goto no_edid;
edid = drm_get_edid(connector, hdata->ddc_adpt);
if (!edid)
- return 0;
+ goto no_edid;
hdata->dvi_mode = !connector->display_info.is_hdmi;
DRM_DEV_DEBUG_KMS(hdata->dev, "%s : width[%d] x height[%d]\n",
@@ -906,6 +906,9 @@ static int hdmi_get_modes(struct drm_connector *connector)
kfree(edid);
return ret;
+
+no_edid:
+ return drm_add_modes_noedid(connector, 640, 480);
}
static int hdmi_find_phy_conf(struct hdmi_context *hdata, u32 pixel_clock)
--
2.34.1