May 2018 - Linux-stable-mirror

patch "w1: mxc_w1: Enable clock before calling clk_get_rate() on it" added to char-misc-next

by gregkh＠linuxfoundation.org

This is a note to let you know that I've just added the patch titled w1: mxc_w1: Enable clock before calling clk_get_rate() on it to my char-misc git tree which can be found at git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc.git in the char-misc-next branch. The patch will show up in the next release of the linux-next tree (usually sometime within the next 24 hours during the week.) The patch will also be merged in the next major kernel release during the merge window. If you have any questions about this process, please let me know. >From 955bc61328dc0a297fb3baccd84e9d3aee501ed8 Mon Sep 17 00:00:00 2001 From: Stefan Potyra <Stefan.Potyra(a)elektrobit.com> Date: Wed, 2 May 2018 10:55:31 +0200 Subject: w1: mxc_w1: Enable clock before calling clk_get_rate() on it According to the API, you may only call clk_get_rate() after actually enabling it. Found by Linux Driver Verification project (linuxtesting.org). Fixes: a5fd9139f74c ("w1: add 1-wire master driver for i.MX27 / i.MX31") Signed-off-by: Stefan Potyra <Stefan.Potyra(a)elektrobit.com> Acked-by: Evgeniy Polyakov <zbr(a)ioremap.net> Cc: stable <stable(a)vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh(a)linuxfoundation.org> --- drivers/w1/masters/mxc_w1.c | 20 +++++++++++++------- 1 file changed, 13 insertions(+), 7 deletions(-) diff --git a/drivers/w1/masters/mxc_w1.c b/drivers/w1/masters/mxc_w1.c index 74f2e6e6202a..8851d441e5fd 100644 --- a/drivers/w1/masters/mxc_w1.c +++ b/drivers/w1/masters/mxc_w1.c @@ -112,6 +112,10 @@ static int mxc_w1_probe(struct platform_device *pdev) if (IS_ERR(mdev->clk)) return PTR_ERR(mdev->clk); + err = clk_prepare_enable(mdev->clk); + if (err) + return err; + clkrate = clk_get_rate(mdev->clk); if (clkrate < 10000000) dev_warn(&pdev->dev, @@ -125,12 +129,10 @@ static int mxc_w1_probe(struct platform_device *pdev) res = platform_get_resource(pdev, IORESOURCE_MEM, 0); mdev->regs = devm_ioremap_resource(&pdev->dev, res); - if (IS_ERR(mdev->regs)) - return PTR_ERR(mdev->regs); - - err = clk_prepare_enable(mdev->clk); - if (err) - return err; + if (IS_ERR(mdev->regs)) { + err = PTR_ERR(mdev->regs); + goto out_disable_clk; + } /* Software reset 1-Wire module */ writeb(MXC_W1_RESET_RST, mdev->regs + MXC_W1_RESET); @@ -146,8 +148,12 @@ static int mxc_w1_probe(struct platform_device *pdev) err = w1_add_master_device(&mdev->bus_master); if (err) - clk_disable_unprepare(mdev->clk); + goto out_disable_clk; + return 0; + +out_disable_clk: + clk_disable_unprepare(mdev->clk); return err; } -- 2.17.0

6 years, 7 months

1
0
0 0

[PATCH] ARM: dts: socfpga: Fix NAND controller node compatible for Arria10

by Dinh Nguyen

The NAND compatible "denali,denal-nand-dt" property has never been used and is obsolete. Remove it. Cc: stable(a)vger.kernel.org Fixes: f549af06e9b6("ARM: dts: socfpga: Add NAND device tree for Arria10") Signed-off-by: Dinh Nguyen <dinguyen(a)kernel.org> --- arch/arm/boot/dts/socfpga_arria10.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/socfpga_arria10.dtsi b/arch/arm/boot/dts/socfpga_arria10.dtsi index bead79e4b2aa..d8b1aa309f76 100644 --- a/arch/arm/boot/dts/socfpga_arria10.dtsi +++ b/arch/arm/boot/dts/socfpga_arria10.dtsi @@ -633,7 +633,7 @@ nand: nand@ffb90000 { #address-cells = <1>; #size-cells = <1>; - compatible = "denali,denali-nand-dt", "altr,socfpga-denali-nand"; + compatible = "altr,socfpga-denali-nand"; reg = <0xffb90000 0x72000>, <0xffb80000 0x10000>; reg-names = "nand_data", "denali_reg"; -- 2.17.0.391.g1f1cddd

6 years, 7 months

1
0
0 0

patch "driver core: Don't ignore class_dir_create_and_add() failure." added to driver-core-testing

by gregkh＠linuxfoundation.org

This is a note to let you know that I've just added the patch titled driver core: Don't ignore class_dir_create_and_add() failure. to my driver-core git tree which can be found at git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core.git in the driver-core-testing branch. The patch will show up in the next release of the linux-next tree (usually sometime within the next 24 hours during the week.) The patch will be merged to the driver-core-next branch sometime soon, after it passes testing, and the merge window is open. If you have any questions about this process, please let me know. >From 84d0c27d6233a9ba0578b20f5a09701eb66cee42 Mon Sep 17 00:00:00 2001 From: Tetsuo Handa <penguin-kernel(a)I-love.SAKURA.ne.jp> Date: Mon, 7 May 2018 19:10:31 +0900 Subject: driver core: Don't ignore class_dir_create_and_add() failure. syzbot is hitting WARN() at kernfs_add_one() [1]. This is because kernfs_create_link() is confused by previous device_add() call which continued without setting dev->kobj.parent field when get_device_parent() failed by memory allocation fault injection. Fix this by propagating the error from class_dir_create_and_add() to the calllers of get_device_parent(). [1] https://syzkaller.appspot.com/bug?id=fae0fb607989ea744526d1c082a5b8de652911… Signed-off-by: Tetsuo Handa <penguin-kernel(a)I-love.SAKURA.ne.jp> Reported-by: syzbot <syzbot+df47f81c226b31d89fb1(a)syzkaller.appspotmail.com> Cc: Greg Kroah-Hartman <gregkh(a)linuxfoundation.org> Cc: stable <stable(a)vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh(a)linuxfoundation.org> --- drivers/base/core.c | 14 ++++++++++++-- 1 file changed, 12 insertions(+), 2 deletions(-) diff --git a/drivers/base/core.c b/drivers/base/core.c index b610816eb887..d680fd030316 100644 --- a/drivers/base/core.c +++ b/drivers/base/core.c @@ -1467,7 +1467,7 @@ class_dir_create_and_add(struct class *class, struct kobject *parent_kobj) dir = kzalloc(sizeof(*dir), GFP_KERNEL); if (!dir) - return NULL; + return ERR_PTR(-ENOMEM); dir->class = class; kobject_init(&dir->kobj, &class_dir_ktype); @@ -1477,7 +1477,7 @@ class_dir_create_and_add(struct class *class, struct kobject *parent_kobj) retval = kobject_add(&dir->kobj, parent_kobj, "%s", class->name); if (retval < 0) { kobject_put(&dir->kobj); - return NULL; + return ERR_PTR(retval); } return &dir->kobj; } @@ -1784,6 +1784,10 @@ int device_add(struct device *dev) parent = get_device(dev->parent); kobj = get_device_parent(dev, parent); + if (IS_ERR(kobj)) { + error = PTR_ERR(kobj); + goto parent_error; + } if (kobj) dev->kobj.parent = kobj; @@ -1882,6 +1886,7 @@ int device_add(struct device *dev) kobject_del(&dev->kobj); Error: cleanup_glue_dir(dev, glue_dir); +parent_error: put_device(parent); name_error: kfree(dev->p); @@ -2701,6 +2706,11 @@ int device_move(struct device *dev, struct device *new_parent, device_pm_lock(); new_parent = get_device(new_parent); new_parent_kobj = get_device_parent(dev, new_parent); + if (IS_ERR(new_parent_kobj)) { + error = PTR_ERR(new_parent_kobj); + put_device(new_parent); + goto out; + } pr_debug("device: '%s': %s: moving to '%s'\n", dev_name(dev), __func__, new_parent ? dev_name(new_parent) : "<NULL>"); -- 2.17.0

6 years, 7 months

1
0
0 0

patch "1wire: family module autoload fails because of upper/lower case" added to char-misc-testing

by gregkh＠linuxfoundation.org

This is a note to let you know that I've just added the patch titled 1wire: family module autoload fails because of upper/lower case to my char-misc git tree which can be found at git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc.git in the char-misc-testing branch. The patch will show up in the next release of the linux-next tree (usually sometime within the next 24 hours during the week.) The patch will be merged to the char-misc-next branch sometime soon, after it passes testing, and the merge window is open. If you have any questions about this process, please let me know. >From 065c09563c872e52813a17218c52cd642be1dca6 Mon Sep 17 00:00:00 2001 From: Ingo Flaschberger <ingo.flaschberger(a)gmail.com> Date: Tue, 1 May 2018 16:10:33 +0200 Subject: 1wire: family module autoload fails because of upper/lower case mismatch. MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit 1wire family module autoload fails because of upper/lower case mismatch. Signed-off-by: Ingo Flaschberger <ingo.flaschberger(a)gmail.com> Acked-by: Evgeniy Polyakov <zbr(a)ioremap.net> Cc: stable <stable(a)vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh(a)linuxfoundation.org> --- drivers/w1/w1.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/w1/w1.c b/drivers/w1/w1.c index 80a778b02f28..caef0e0fd817 100644 --- a/drivers/w1/w1.c +++ b/drivers/w1/w1.c @@ -751,7 +751,7 @@ int w1_attach_slave_device(struct w1_master *dev, struct w1_reg_num *rn) /* slave modules need to be loaded in a context with unlocked mutex */ mutex_unlock(&dev->mutex); - request_module("w1-family-0x%02x", rn->family); + request_module("w1-family-0x%02X", rn->family); mutex_lock(&dev->mutex); spin_lock(&w1_flock); -- 2.17.0

6 years, 7 months

1
0
0 0

patch "w1: mxc_w1: Enable clock before calling clk_get_rate() on it" added to char-misc-testing

by gregkh＠linuxfoundation.org

This is a note to let you know that I've just added the patch titled w1: mxc_w1: Enable clock before calling clk_get_rate() on it to my char-misc git tree which can be found at git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc.git in the char-misc-testing branch. The patch will show up in the next release of the linux-next tree (usually sometime within the next 24 hours during the week.) The patch will be merged to the char-misc-next branch sometime soon, after it passes testing, and the merge window is open. If you have any questions about this process, please let me know. >From 955bc61328dc0a297fb3baccd84e9d3aee501ed8 Mon Sep 17 00:00:00 2001 From: Stefan Potyra <Stefan.Potyra(a)elektrobit.com> Date: Wed, 2 May 2018 10:55:31 +0200 Subject: w1: mxc_w1: Enable clock before calling clk_get_rate() on it According to the API, you may only call clk_get_rate() after actually enabling it. Found by Linux Driver Verification project (linuxtesting.org). Fixes: a5fd9139f74c ("w1: add 1-wire master driver for i.MX27 / i.MX31") Signed-off-by: Stefan Potyra <Stefan.Potyra(a)elektrobit.com> Acked-by: Evgeniy Polyakov <zbr(a)ioremap.net> Cc: stable <stable(a)vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh(a)linuxfoundation.org> --- drivers/w1/masters/mxc_w1.c | 20 +++++++++++++------- 1 file changed, 13 insertions(+), 7 deletions(-) diff --git a/drivers/w1/masters/mxc_w1.c b/drivers/w1/masters/mxc_w1.c index 74f2e6e6202a..8851d441e5fd 100644 --- a/drivers/w1/masters/mxc_w1.c +++ b/drivers/w1/masters/mxc_w1.c @@ -112,6 +112,10 @@ static int mxc_w1_probe(struct platform_device *pdev) if (IS_ERR(mdev->clk)) return PTR_ERR(mdev->clk); + err = clk_prepare_enable(mdev->clk); + if (err) + return err; + clkrate = clk_get_rate(mdev->clk); if (clkrate < 10000000) dev_warn(&pdev->dev, @@ -125,12 +129,10 @@ static int mxc_w1_probe(struct platform_device *pdev) res = platform_get_resource(pdev, IORESOURCE_MEM, 0); mdev->regs = devm_ioremap_resource(&pdev->dev, res); - if (IS_ERR(mdev->regs)) - return PTR_ERR(mdev->regs); - - err = clk_prepare_enable(mdev->clk); - if (err) - return err; + if (IS_ERR(mdev->regs)) { + err = PTR_ERR(mdev->regs); + goto out_disable_clk; + } /* Software reset 1-Wire module */ writeb(MXC_W1_RESET_RST, mdev->regs + MXC_W1_RESET); @@ -146,8 +148,12 @@ static int mxc_w1_probe(struct platform_device *pdev) err = w1_add_master_device(&mdev->bus_master); if (err) - clk_disable_unprepare(mdev->clk); + goto out_disable_clk; + return 0; + +out_disable_clk: + clk_disable_unprepare(mdev->clk); return err; } -- 2.17.0

6 years, 7 months

1
0
0 0

[PATCH] IB/srpt: Increase port count

by Bart Van Assche

Since there are adapters that have four ports, increase the size of the srpt_device.port[] array. This patch avoids that the following warning is hit with quad port Chelsio adapters: WARN_ON(sdev->device->phys_port_cnt > ARRAY_SIZE(sdev->port)); Reported-by: Steve Wise <swise(a)opengridcomputing.com> Signed-off-by: Bart Van Assche <bart.vanassche(a)wdc.com> Cc: Steve Wise <swise(a)opengridcomputing.com> Cc: <stable(a)vger.kernel.org> --- drivers/infiniband/ulp/srpt/ib_srpt.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/infiniband/ulp/srpt/ib_srpt.h b/drivers/infiniband/ulp/srpt/ib_srpt.h index 2361483476a0..b72f1f4066fa 100644 --- a/drivers/infiniband/ulp/srpt/ib_srpt.h +++ b/drivers/infiniband/ulp/srpt/ib_srpt.h @@ -410,7 +410,7 @@ struct srpt_device { struct mutex sdev_mutex; bool use_srq; struct srpt_recv_ioctx **ioctx_ring; - struct srpt_port port[2]; + struct srpt_port port[4]; struct ib_event_handler event_handler; struct list_head list; }; -- 2.16.3

6 years, 7 months

4
3
0 0

patch "serial: 8250: omap: Fix idling of clocks for unused uarts" added to tty-testing

by gregkh＠linuxfoundation.org

This is a note to let you know that I've just added the patch titled serial: 8250: omap: Fix idling of clocks for unused uarts to my tty git tree which can be found at git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty.git in the tty-testing branch. The patch will show up in the next release of the linux-next tree (usually sometime within the next 24 hours during the week.) The patch will be merged to the tty-next branch sometime soon, after it passes testing, and the merge window is open. If you have any questions about this process, please let me know. >From 13dc04d0e5fdc25c8f713ad23fdce51cf2bf96ba Mon Sep 17 00:00:00 2001 From: Tony Lindgren <tony(a)atomide.com> Date: Fri, 4 May 2018 10:44:09 -0700 Subject: serial: 8250: omap: Fix idling of clocks for unused uarts I noticed that unused UARTs won't necessarily idle properly always unless at least one byte tx transfer is done first. After some debugging I narrowed down the problem to the scr register dma configuration bits that need to be set before softreset for the clocks to idle. Unless we do this, the module clkctrl idlest bits may be set to 1 instead of 3 meaning the clock will never idle and is blocking deeper idle states for the whole domain. This might be related to the configuration done by the bootloader or kexec booting where certain configurations cause the 8250 or the clkctrl clock to jam in a way where setting of the scr bits and reset is needed to clear it. I've tried diffing the 8250 registers for the various modes, but did not see anything specific. So far I've only seen this on omap4 but I'm suspecting this might also happen on the other clkctrl using SoCs considering they already have a quirk enabled for UART_ERRATA_CLOCK_DISABLE. Let's fix the issue by configuring scr before reset for basic dma even if we don't use it. The scr register will be reset when we do softreset few lines after, and we restore scr on resume. We should do this for all the SoCs with UART_ERRATA_CLOCK_DISABLE quirk flag set since the ones with UART_ERRATA_CLOCK_DISABLE are all based using clkctrl similar to omap4. Looks like both OMAP_UART_SCR_DMAMODE_1 | OMAP_UART_SCR_DMAMODE_CTL bits are needed for the clkctrl to idle after a softreset. And we need to add omap4 to also use the UART_ERRATA_CLOCK_DISABLE for the related workaround to be enabled. This same compatible value will also be used for omap5. Fixes: cdb929e4452a ("serial: 8250_omap: workaround errata around idling UART after using DMA") Cc: Keerthy <j-keerthy(a)ti.com> Cc: Matthijs van Duin <matthijsvanduin(a)gmail.com> Cc: Sekhar Nori <nsekhar(a)ti.com> Cc: Tero Kristo <t-kristo(a)ti.com> Signed-off-by: Tony Lindgren <tony(a)atomide.com> Cc: stable <stable(a)vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh(a)linuxfoundation.org> --- drivers/tty/serial/8250/8250_omap.c | 16 +++++++++++++++- 1 file changed, 15 insertions(+), 1 deletion(-) diff --git a/drivers/tty/serial/8250/8250_omap.c b/drivers/tty/serial/8250/8250_omap.c index 6aaa84355fd1..1b337fee07ed 100644 --- a/drivers/tty/serial/8250/8250_omap.c +++ b/drivers/tty/serial/8250/8250_omap.c @@ -1110,13 +1110,14 @@ static int omap8250_no_handle_irq(struct uart_port *port) return 0; } +static const u8 omap4_habit = UART_ERRATA_CLOCK_DISABLE; static const u8 am3352_habit = OMAP_DMA_TX_KICK | UART_ERRATA_CLOCK_DISABLE; static const u8 dra742_habit = UART_ERRATA_CLOCK_DISABLE; static const struct of_device_id omap8250_dt_ids[] = { { .compatible = "ti,omap2-uart" }, { .compatible = "ti,omap3-uart" }, - { .compatible = "ti,omap4-uart" }, + { .compatible = "ti,omap4-uart", .data = &omap4_habit, }, { .compatible = "ti,am3352-uart", .data = &am3352_habit, }, { .compatible = "ti,am4372-uart", .data = &am3352_habit, }, { .compatible = "ti,dra742-uart", .data = &dra742_habit, }, @@ -1362,6 +1363,19 @@ static int omap8250_soft_reset(struct device *dev) int sysc; int syss; + /* + * At least on omap4, unused uarts may not idle after reset without + * a basic scr dma configuration even with no dma in use. The + * module clkctrl status bits will be 1 instead of 3 blocking idle + * for the whole clockdomain. The softreset below will clear scr, + * and we restore it on resume so this is safe to do on all SoCs + * needing omap8250_soft_reset() quirk. Do it in two writes as + * recommended in the comment for omap8250_update_scr(). + */ + serial_out(up, UART_OMAP_SCR, OMAP_UART_SCR_DMAMODE_1); + serial_out(up, UART_OMAP_SCR, + OMAP_UART_SCR_DMAMODE_1 | OMAP_UART_SCR_DMAMODE_CTL); + sysc = serial_in(up, UART_OMAP_SYSC); /* softreset the UART */ -- 2.17.0

6 years, 7 months

1
0
0 0

patch "serial: samsung: fix maxburst parameter for DMA transactions" added to tty-testing

by gregkh＠linuxfoundation.org

This is a note to let you know that I've just added the patch titled serial: samsung: fix maxburst parameter for DMA transactions to my tty git tree which can be found at git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty.git in the tty-testing branch. The patch will show up in the next release of the linux-next tree (usually sometime within the next 24 hours during the week.) The patch will be merged to the tty-next branch sometime soon, after it passes testing, and the merge window is open. If you have any questions about this process, please let me know. >From aa2f80e752c75e593b3820f42c416ed9458fa73e Mon Sep 17 00:00:00 2001 From: Marek Szyprowski <m.szyprowski(a)samsung.com> Date: Thu, 10 May 2018 08:41:13 +0200 Subject: serial: samsung: fix maxburst parameter for DMA transactions The best granularity of residue that DMA engine can report is in the BURST units, so the serial driver must use MAXBURST = 1 and DMA_SLAVE_BUSWIDTH_1_BYTE if it relies on exact number of bytes transferred by DMA engine. Fixes: 62c37eedb74c ("serial: samsung: add dma reqest/release functions") Signed-off-by: Marek Szyprowski <m.szyprowski(a)samsung.com> Acked-by: Krzysztof Kozlowski <krzk(a)kernel.org> Cc: stable <stable(a)vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh(a)linuxfoundation.org> --- drivers/tty/serial/samsung.c | 7 ++----- 1 file changed, 2 insertions(+), 5 deletions(-) diff --git a/drivers/tty/serial/samsung.c b/drivers/tty/serial/samsung.c index 3f2f8c118ce0..64e96926f1ad 100644 --- a/drivers/tty/serial/samsung.c +++ b/drivers/tty/serial/samsung.c @@ -862,15 +862,12 @@ static int s3c24xx_serial_request_dma(struct s3c24xx_uart_port *p) dma->rx_conf.direction = DMA_DEV_TO_MEM; dma->rx_conf.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE; dma->rx_conf.src_addr = p->port.mapbase + S3C2410_URXH; - dma->rx_conf.src_maxburst = 16; + dma->rx_conf.src_maxburst = 1; dma->tx_conf.direction = DMA_MEM_TO_DEV; dma->tx_conf.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE; dma->tx_conf.dst_addr = p->port.mapbase + S3C2410_UTXH; - if (dma_get_cache_alignment() >= 16) - dma->tx_conf.dst_maxburst = 16; - else - dma->tx_conf.dst_maxburst = 1; + dma->tx_conf.dst_maxburst = 1; dma->rx_chan = dma_request_chan(p->port.dev, "rx"); -- 2.17.0

6 years, 7 months

1
0
0 0

patch "tty: pl011: Avoid spuriously stuck-off interrupts" added to tty-testing

by gregkh＠linuxfoundation.org

This is a note to let you know that I've just added the patch titled tty: pl011: Avoid spuriously stuck-off interrupts to my tty git tree which can be found at git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty.git in the tty-testing branch. The patch will show up in the next release of the linux-next tree (usually sometime within the next 24 hours during the week.) The patch will be merged to the tty-next branch sometime soon, after it passes testing, and the merge window is open. If you have any questions about this process, please let me know. >From 4a7e625ce50412a7711efa0f2ef0b96ce3826759 Mon Sep 17 00:00:00 2001 From: Dave Martin <Dave.Martin(a)arm.com> Date: Thu, 10 May 2018 18:08:23 +0100 Subject: tty: pl011: Avoid spuriously stuck-off interrupts Commit 9b96fbacda34 ("serial: PL011: clear pending interrupts") clears the RX and receive timeout interrupts on pl011 startup, to avoid a screaming-interrupt scenario that can occur when the firmware or bootloader leaves these interrupts asserted. This has been noted as an issue when running Linux on qemu [1]. Unfortunately, the above fix seems to lead to potential misbehaviour if the RX FIFO interrupt is asserted _non_ spuriously on driver startup, if the RX FIFO is also already full to the trigger level. Clearing the RX FIFO interrupt does not change the FIFO fill level. In this scenario, because the interrupt is now clear and because the FIFO is already full to the trigger level, no new assertion of the RX FIFO interrupt can occur unless the FIFO is drained back below the trigger level. This never occurs because the pl011 driver is waiting for an RX FIFO interrupt to tell it that there is something to read, and does not read the FIFO at all until that interrupt occurs. Thus, simply clearing "spurious" interrupts on startup may be misguided, since there is no way to be sure that the interrupts are truly spurious, and things can go wrong if they are not. This patch instead clears the interrupt condition by draining the RX FIFO during UART startup, after clearing any potentially spurious interrupt. This should ensure that an interrupt will definitely be asserted if the RX FIFO subsequently becomes sufficiently full. The drain is done at the point of enabling interrupts only. This means that it will occur any time the UART is newly opened through the tty layer. It will not apply to polled-mode use of the UART by kgdboc: since that scenario cannot use interrupts by design, this should not matter. kgdboc will interact badly with "normal" use of the UART in any case: this patch makes no attempt to paper over such issues. This patch does not attempt to address the case where the RX FIFO fills faster than it can be drained: that is a pathological hardware design problem that is beyond the scope of the driver to work around. As a failsafe, the number of poll iterations for draining the FIFO is limited to twice the FIFO size. This will ensure that the kernel at least boots even if it is impossible to drain the FIFO for some reason. [1] [Qemu-devel] [Qemu-arm] [PATCH] pl011: do not put into fifo before enabled the interruption https://lists.gnu.org/archive/html/qemu-devel/2018-01/msg06446.html Reported-by: Wei Xu <xuwei5(a)hisilicon.com> Cc: Russell King <linux(a)armlinux.org.uk> Cc: Linus Walleij <linus.walleij(a)linaro.org> Cc: Peter Maydell <peter.maydell(a)linaro.org> Fixes: 9b96fbacda34 ("serial: PL011: clear pending interrupts") Signed-off-by: Dave Martin <Dave.Martin(a)arm.com> Cc: stable <stable(a)vger.kernel.org> Tested-by: Wei Xu <xuwei5(a)hisilicon.com> Signed-off-by: Greg Kroah-Hartman <gregkh(a)linuxfoundation.org> --- drivers/tty/serial/amba-pl011.c | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c index 4b40a5b449ee..ebd33c0232e6 100644 --- a/drivers/tty/serial/amba-pl011.c +++ b/drivers/tty/serial/amba-pl011.c @@ -1727,10 +1727,26 @@ static int pl011_allocate_irq(struct uart_amba_port *uap) */ static void pl011_enable_interrupts(struct uart_amba_port *uap) { + unsigned int i; + spin_lock_irq(&uap->port.lock); /* Clear out any spuriously appearing RX interrupts */ pl011_write(UART011_RTIS | UART011_RXIS, uap, REG_ICR); + + /* + * RXIS is asserted only when the RX FIFO transitions from below + * to above the trigger threshold. If the RX FIFO is already + * full to the threshold this can't happen and RXIS will now be + * stuck off. Drain the RX FIFO explicitly to fix this: + */ + for (i = 0; i < uap->fifosize * 2; ++i) { + if (pl011_read(uap, REG_FR) & UART01x_FR_RXFE) + break; + + pl011_read(uap, REG_DR); + } + uap->im = UART011_RTIM; if (!pl011_dma_rx_running(uap)) uap->im |= UART011_RXIM; -- 2.17.0

6 years, 7 months

1
0
0 0

patch "xhci: Fix USB3 NULL pointer dereference at logical disconnect." added to usb-linus

by gregkh＠linuxfoundation.org

This is a note to let you know that I've just added the patch titled xhci: Fix USB3 NULL pointer dereference at logical disconnect. to my usb git tree which can be found at git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb.git in the usb-linus branch. The patch will show up in the next release of the linux-next tree (usually sometime within the next 24 hours during the week.) The patch will hopefully also be merged in Linus's tree for the next -rc kernel release. If you have any questions about this process, please let me know. >From 2278446e2b7cd33ad894b32e7eb63afc7db6c86e Mon Sep 17 00:00:00 2001 From: Mathias Nyman <mathias.nyman(a)linux.intel.com> Date: Mon, 14 May 2018 11:57:23 +0300 Subject: xhci: Fix USB3 NULL pointer dereference at logical disconnect. Hub driver will try to disable a USB3 device twice at logical disconnect, racing with xhci_free_dev() callback from the first port disable. This can be triggered with "udisksctl power-off --block-device <disk>" or by writing "1" to the "remove" sysfs file for a USB3 device in 4.17-rc4. USB3 devices don't have a similar disabled link state as USB2 devices, and use a U3 suspended link state instead. In this state the port is still enabled and connected. hub_port_connect() first disconnects the device, then later it notices that device is still enabled (due to U3 states) it will try to disable the port again (set to U3). The xhci_free_dev() called during device disable is async, so checking for existing xhci->devs[i] when setting link state to U3 the second time was successful, even if device was being freed. The regression was caused by, and whole thing revealed by, Commit 44a182b9d177 ("xhci: Fix use-after-free in xhci_free_virt_device") which sets xhci->devs[i]->udev to NULL before xhci_virt_dev() returned. and causes a NULL pointer dereference the second time we try to set U3. Fix this by checking xhci->devs[i]->udev exists before setting link state. The original patch went to stable so this fix needs to be applied there as well. Fixes: 44a182b9d177 ("xhci: Fix use-after-free in xhci_free_virt_device") Cc: <stable(a)vger.kernel.org> Reported-by: Jordan Glover <Golden_Miller83(a)protonmail.ch> Tested-by: Jordan Glover <Golden_Miller83(a)protonmail.ch> Signed-off-by: Mathias Nyman <mathias.nyman(a)linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh(a)linuxfoundation.org> --- drivers/usb/host/xhci-hub.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/usb/host/xhci-hub.c b/drivers/usb/host/xhci-hub.c index 72ebbc908e19..32cd52ca8318 100644 --- a/drivers/usb/host/xhci-hub.c +++ b/drivers/usb/host/xhci-hub.c @@ -354,7 +354,7 @@ int xhci_find_slot_id_by_port(struct usb_hcd *hcd, struct xhci_hcd *xhci, slot_id = 0; for (i = 0; i < MAX_HC_SLOTS; i++) { - if (!xhci->devs[i]) + if (!xhci->devs[i] || !xhci->devs[i]->udev) continue; speed = xhci->devs[i]->udev->speed; if (((speed >= USB_SPEED_SUPER) == (hcd->speed >= HCD_USB3)) -- 2.17.0

6 years, 7 months

1
0
0 0

2024

2023

2022

2021

2020

2019

2018

2017

Linux-stable-mirror May 2018