February 2018 - Linux-stable-mirror

[PATCH v3] ASoC: sgtl5000: Fix suspend/resume

by Fabio Estevam

From: Fabio Estevam <fabio.estevam(a)nxp.com> Commit 8419caa72702 ("ASoC: sgtl5000: Do not disable regulators in SND_SOC_BIAS_OFF") causes the sgtl5000 to fail after a suspend/resume sequence: # aplay /media/a2002011001-e02.wav Playing WAVE '/media/a2002011001-e02.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo aplay: pcm_write:2051: write error: Input/output error The problem is caused by the fact that the aforementioned commit dropped the cache handling, so re-introduce the register map resync to fix the problem. Cc: <stable(a)vger.kernel.org> Suggested-by: Mark Brown <broonie(a)kernel.org> Signed-off-by: Fabio Estevam <fabio.estevam(a)nxp.com> --- Changes since v2: - Rebased against Linus' tree sound/soc/codecs/sgtl5000.c | 11 +++++++++++ 1 file changed, 11 insertions(+) diff --git a/sound/soc/codecs/sgtl5000.c b/sound/soc/codecs/sgtl5000.c index e1ab553..7ff5cb7 100644 --- a/sound/soc/codecs/sgtl5000.c +++ b/sound/soc/codecs/sgtl5000.c @@ -871,15 +871,26 @@ static int sgtl5000_pcm_hw_params(struct snd_pcm_substream *substream, static int sgtl5000_set_bias_level(struct snd_soc_codec *codec, enum snd_soc_bias_level level) { + struct sgtl5000_priv *sgtl = snd_soc_codec_get_drvdata(codec); + int ret; + switch (level) { case SND_SOC_BIAS_ON: case SND_SOC_BIAS_PREPARE: case SND_SOC_BIAS_STANDBY: + regcache_cache_only(sgtl->regmap, false); + ret = regcache_sync(sgtl->regmap); + if (ret) { + regcache_cache_only(sgtl->regmap, true); + return ret; + } + snd_soc_update_bits(codec, SGTL5000_CHIP_ANA_POWER, SGTL5000_REFTOP_POWERUP, SGTL5000_REFTOP_POWERUP); break; case SND_SOC_BIAS_OFF: + regcache_cache_only(sgtl->regmap, true); snd_soc_update_bits(codec, SGTL5000_CHIP_ANA_POWER, SGTL5000_REFTOP_POWERUP, 0); break; -- 2.7.4

6 years, 11 months

2
1
0 0

patch "ANDROID: binder: synchronize_rcu() when using POLLFREE." added to char-misc-linus

by gregkh＠linuxfoundation.org

This is a note to let you know that I've just added the patch titled ANDROID: binder: synchronize_rcu() when using POLLFREE. to my char-misc git tree which can be found at git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc.git in the char-misc-linus branch. The patch will show up in the next release of the linux-next tree (usually sometime within the next 24 hours during the week.) The patch will hopefully also be merged in Linus's tree for the next -rc kernel release. If you have any questions about this process, please let me know. >From 5eeb2ca02a2f6084fc57ae5c244a38baab07033a Mon Sep 17 00:00:00 2001 From: Martijn Coenen <maco(a)android.com> Date: Fri, 16 Feb 2018 09:47:15 +0100 Subject: ANDROID: binder: synchronize_rcu() when using POLLFREE. To prevent races with ep_remove_waitqueue() removing the waitqueue at the same time. Reported-by: syzbot+a2a3c4909716e271487e(a)syzkaller.appspotmail.com Signed-off-by: Martijn Coenen <maco(a)android.com> Cc: stable <stable(a)vger.kernel.org> # 4.14+ Signed-off-by: Greg Kroah-Hartman <gregkh(a)linuxfoundation.org> --- drivers/android/binder.c | 9 +++++++++ 1 file changed, 9 insertions(+) diff --git a/drivers/android/binder.c b/drivers/android/binder.c index a85f9033b57e..764b63a5aade 100644 --- a/drivers/android/binder.c +++ b/drivers/android/binder.c @@ -4382,6 +4382,15 @@ static int binder_thread_release(struct binder_proc *proc, binder_inner_proc_unlock(thread->proc); + /* + * This is needed to avoid races between wake_up_poll() above and + * and ep_remove_waitqueue() called for other reasons (eg the epoll file + * descriptor being closed); ep_remove_waitqueue() holds an RCU read + * lock, so we can be sure it's done after calling synchronize_rcu(). + */ + if (thread->looper & BINDER_LOOPER_STATE_POLL) + synchronize_rcu(); + if (send_reply) binder_send_failed_reply(send_reply, BR_DEAD_REPLY); binder_release_work(proc, &thread->todo); -- 2.16.1

6 years, 11 months

1
0
0 0

patch "binder: replace "%p" with "%pK"" added to char-misc-linus

by gregkh＠linuxfoundation.org

This is a note to let you know that I've just added the patch titled binder: replace "%p" with "%pK" to my char-misc git tree which can be found at git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc.git in the char-misc-linus branch. The patch will show up in the next release of the linux-next tree (usually sometime within the next 24 hours during the week.) The patch will hopefully also be merged in Linus's tree for the next -rc kernel release. If you have any questions about this process, please let me know. >From 8ca86f1639ec5890d400fff9211aca22d0a392eb Mon Sep 17 00:00:00 2001 From: Todd Kjos <tkjos(a)android.com> Date: Wed, 7 Feb 2018 13:57:37 -0800 Subject: binder: replace "%p" with "%pK" The format specifier "%p" can leak kernel addresses. Use "%pK" instead. There were 4 remaining cases in binder.c. Signed-off-by: Todd Kjos <tkjos(a)google.com> Cc: stable <stable(a)vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh(a)linuxfoundation.org> --- drivers/android/binder.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/drivers/android/binder.c b/drivers/android/binder.c index 31322e9a235d..a85f9033b57e 100644 --- a/drivers/android/binder.c +++ b/drivers/android/binder.c @@ -2199,7 +2199,7 @@ static void binder_transaction_buffer_release(struct binder_proc *proc, int debug_id = buffer->debug_id; binder_debug(BINDER_DEBUG_TRANSACTION, - "%d buffer release %d, size %zd-%zd, failed at %p\n", + "%d buffer release %d, size %zd-%zd, failed at %pK\n", proc->pid, buffer->debug_id, buffer->data_size, buffer->offsets_size, failed_at); @@ -3711,7 +3711,7 @@ static int binder_thread_write(struct binder_proc *proc, } } binder_debug(BINDER_DEBUG_DEAD_BINDER, - "%d:%d BC_DEAD_BINDER_DONE %016llx found %p\n", + "%d:%d BC_DEAD_BINDER_DONE %016llx found %pK\n", proc->pid, thread->pid, (u64)cookie, death); if (death == NULL) { @@ -5042,7 +5042,7 @@ static void print_binder_transaction_ilocked(struct seq_file *m, spin_lock(&t->lock); to_proc = t->to_proc; seq_printf(m, - "%s %d: %p from %d:%d to %d:%d code %x flags %x pri %ld r%d", + "%s %d: %pK from %d:%d to %d:%d code %x flags %x pri %ld r%d", prefix, t->debug_id, t, t->from ? t->from->proc->pid : 0, t->from ? t->from->pid : 0, @@ -5066,7 +5066,7 @@ static void print_binder_transaction_ilocked(struct seq_file *m, } if (buffer->target_node) seq_printf(m, " node %d", buffer->target_node->debug_id); - seq_printf(m, " size %zd:%zd data %p\n", + seq_printf(m, " size %zd:%zd data %pK\n", buffer->data_size, buffer->offsets_size, buffer->data); } -- 2.16.1

6 years, 11 months

1
0
0 0

patch "ANDROID: binder: remove WARN() for redundant txn error" added to char-misc-linus

by gregkh＠linuxfoundation.org

This is a note to let you know that I've just added the patch titled ANDROID: binder: remove WARN() for redundant txn error to my char-misc git tree which can be found at git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc.git in the char-misc-linus branch. The patch will show up in the next release of the linux-next tree (usually sometime within the next 24 hours during the week.) The patch will hopefully also be merged in Linus's tree for the next -rc kernel release. If you have any questions about this process, please let me know. >From e46a3b3ba7509cb7fda0e07bc7c63a2cd90f579b Mon Sep 17 00:00:00 2001 From: Todd Kjos <tkjos(a)android.com> Date: Wed, 7 Feb 2018 12:38:47 -0800 Subject: ANDROID: binder: remove WARN() for redundant txn error binder_send_failed_reply() is called when a synchronous transaction fails. It reports an error to the thread that is waiting for the completion. Given that the transaction is synchronous, there should never be more than 1 error response to that thread -- this was being asserted with a WARN(). However, when exercising the driver with syzbot tests, cases were observed where multiple "synchronous" requests were sent without waiting for responses, so it is possible that multiple errors would be reported to the thread. This testing was conducted with panic_on_warn set which forced the crash. This is easily reproduced by sending back-to-back "synchronous" transactions without checking for any response (eg, set read_size to 0): bwr.write_buffer = (uintptr_t)&bc1; bwr.write_size = sizeof(bc1); bwr.read_buffer = (uintptr_t)&br; bwr.read_size = 0; ioctl(fd, BINDER_WRITE_READ, &bwr); sleep(1); bwr2.write_buffer = (uintptr_t)&bc2; bwr2.write_size = sizeof(bc2); bwr2.read_buffer = (uintptr_t)&br; bwr2.read_size = 0; ioctl(fd, BINDER_WRITE_READ, &bwr2); sleep(1); The first transaction is sent to the servicemanager and the reply fails because no VMA is set up by this client. After binder_send_failed_reply() is called, the BINDER_WORK_RETURN_ERROR is sitting on the thread's todo list since the read_size was 0 and the client is not waiting for a response. The 2nd transaction is sent and the BINDER_WORK_RETURN_ERROR has not been consumed, so the thread's reply_error.cmd is still set (normally cleared when the BINDER_WORK_RETURN_ERROR is handled). Therefore when the servicemanager attempts to reply to the 2nd failed transaction, the error is already set and it triggers this warning. This is a user error since it is not waiting for the synchronous transaction to complete. If it ever does check, it will see an error. Changed the WARN() to a pr_warn(). Signed-off-by: Todd Kjos <tkjos(a)android.com> Reported-by: syzbot <syzkaller(a)googlegroups.com> Cc: stable <stable(a)vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh(a)linuxfoundation.org> --- drivers/android/binder.c | 10 ++++++++-- 1 file changed, 8 insertions(+), 2 deletions(-) diff --git a/drivers/android/binder.c b/drivers/android/binder.c index ad5e662e3e14..31322e9a235d 100644 --- a/drivers/android/binder.c +++ b/drivers/android/binder.c @@ -1991,8 +1991,14 @@ static void binder_send_failed_reply(struct binder_transaction *t, &target_thread->reply_error.work); wake_up_interruptible(&target_thread->wait); } else { - WARN(1, "Unexpected reply error: %u\n", - target_thread->reply_error.cmd); + /* + * Cannot get here for normal operation, but + * we can if multiple synchronous transactions + * are sent without blocking for responses. + * Just ignore the 2nd error in this case. + */ + pr_warn("Unexpected reply error: %u\n", + target_thread->reply_error.cmd); } binder_inner_proc_unlock(target_thread->proc); binder_thread_dec_tmpref(target_thread); -- 2.16.1

6 years, 11 months

1
0
0 0

patch "usb: dwc3: core: Fix ULPI PHYs and prevent phy_get/ulpi_init during" added to usb-linus

by gregkh＠linuxfoundation.org

This is a note to let you know that I've just added the patch titled usb: dwc3: core: Fix ULPI PHYs and prevent phy_get/ulpi_init during to my usb git tree which can be found at git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb.git in the usb-linus branch. The patch will show up in the next release of the linux-next tree (usually sometime within the next 24 hours during the week.) The patch will hopefully also be merged in Linus's tree for the next -rc kernel release. If you have any questions about this process, please let me know. >From 98112041bcca164676367e261c8c1073ef70cb51 Mon Sep 17 00:00:00 2001 From: Roger Quadros <rogerq(a)ti.com> Date: Mon, 12 Feb 2018 15:30:08 +0200 Subject: usb: dwc3: core: Fix ULPI PHYs and prevent phy_get/ulpi_init during suspend/resume In order for ULPI PHYs to work, dwc3_phy_setup() and dwc3_ulpi_init() must be doene before dwc3_core_get_phy(). commit 541768b08a40 ("usb: dwc3: core: Call dwc3_core_get_phy() before initializing phys") broke this. The other issue is that dwc3_core_get_phy() and dwc3_ulpi_init() should be called only once during the life cycle of the driver. However, as dwc3_core_init() is called during system suspend/resume it will result in multiple calls to dwc3_core_get_phy() and dwc3_ulpi_init() which is wrong. Fix this by moving dwc3_ulpi_init() out of dwc3_phy_setup() into dwc3_core_ulpi_init(). Use a flag 'ulpi_ready' to ensure that dwc3_core_ulpi_init() is called only once from dwc3_core_init(). Use another flag 'phys_ready' to call dwc3_core_get_phy() only once from dwc3_core_init(). Fixes: 541768b08a40 ("usb: dwc3: core: Call dwc3_core_get_phy() before initializing phys") Fixes: f54edb539c11 ("usb: dwc3: core: initialize ULPI before trying to get the PHY") Cc: linux-stable <stable(a)vger.kernel.org> # >= v4.13 Signed-off-by: Roger Quadros <rogerq(a)ti.com> Signed-off-by: Felipe Balbi <felipe.balbi(a)linux.intel.com> --- drivers/usb/dwc3/core.c | 47 ++++++++++++++++++++++++++++++++++++----------- drivers/usb/dwc3/core.h | 5 +++++ 2 files changed, 41 insertions(+), 11 deletions(-) diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c index 59511f2cd3ac..f1d838a4acd6 100644 --- a/drivers/usb/dwc3/core.c +++ b/drivers/usb/dwc3/core.c @@ -486,6 +486,22 @@ static void dwc3_cache_hwparams(struct dwc3 *dwc) parms->hwparams8 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS8); } +static int dwc3_core_ulpi_init(struct dwc3 *dwc) +{ + int intf; + int ret = 0; + + intf = DWC3_GHWPARAMS3_HSPHY_IFC(dwc->hwparams.hwparams3); + + if (intf == DWC3_GHWPARAMS3_HSPHY_IFC_ULPI || + (intf == DWC3_GHWPARAMS3_HSPHY_IFC_UTMI_ULPI && + dwc->hsphy_interface && + !strncmp(dwc->hsphy_interface, "ulpi", 4))) + ret = dwc3_ulpi_init(dwc); + + return ret; +} + /** * dwc3_phy_setup - Configure USB PHY Interface of DWC3 Core * @dwc: Pointer to our controller context structure @@ -497,7 +513,6 @@ static void dwc3_cache_hwparams(struct dwc3 *dwc) static int dwc3_phy_setup(struct dwc3 *dwc) { u32 reg; - int ret; reg = dwc3_readl(dwc->regs, DWC3_GUSB3PIPECTL(0)); @@ -568,9 +583,6 @@ static int dwc3_phy_setup(struct dwc3 *dwc) } /* FALLTHROUGH */ case DWC3_GHWPARAMS3_HSPHY_IFC_ULPI: - ret = dwc3_ulpi_init(dwc); - if (ret) - return ret; /* FALLTHROUGH */ default: break; @@ -727,6 +739,7 @@ static void dwc3_core_setup_global_control(struct dwc3 *dwc) } static int dwc3_core_get_phy(struct dwc3 *dwc); +static int dwc3_core_ulpi_init(struct dwc3 *dwc); /** * dwc3_core_init - Low-level initialization of DWC3 Core @@ -758,17 +771,27 @@ static int dwc3_core_init(struct dwc3 *dwc) dwc->maximum_speed = USB_SPEED_HIGH; } - ret = dwc3_core_get_phy(dwc); + ret = dwc3_phy_setup(dwc); if (ret) goto err0; - ret = dwc3_core_soft_reset(dwc); - if (ret) - goto err0; + if (!dwc->ulpi_ready) { + ret = dwc3_core_ulpi_init(dwc); + if (ret) + goto err0; + dwc->ulpi_ready = true; + } - ret = dwc3_phy_setup(dwc); + if (!dwc->phys_ready) { + ret = dwc3_core_get_phy(dwc); + if (ret) + goto err0a; + dwc->phys_ready = true; + } + + ret = dwc3_core_soft_reset(dwc); if (ret) - goto err0; + goto err0a; dwc3_core_setup_global_control(dwc); dwc3_core_num_eps(dwc); @@ -841,6 +864,9 @@ static int dwc3_core_init(struct dwc3 *dwc) phy_exit(dwc->usb2_generic_phy); phy_exit(dwc->usb3_generic_phy); +err0a: + dwc3_ulpi_exit(dwc); + err0: return ret; } @@ -1235,7 +1261,6 @@ static int dwc3_probe(struct platform_device *pdev) err3: dwc3_free_event_buffers(dwc); - dwc3_ulpi_exit(dwc); err2: pm_runtime_allow(&pdev->dev); diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h index 185b9603fd98..860d2bc184d1 100644 --- a/drivers/usb/dwc3/core.h +++ b/drivers/usb/dwc3/core.h @@ -797,7 +797,9 @@ struct dwc3_scratchpad_array { * @usb3_phy: pointer to USB3 PHY * @usb2_generic_phy: pointer to USB2 PHY * @usb3_generic_phy: pointer to USB3 PHY + * @phys_ready: flag to indicate that PHYs are ready * @ulpi: pointer to ulpi interface + * @ulpi_ready: flag to indicate that ULPI is initialized * @u2sel: parameter from Set SEL request. * @u2pel: parameter from Set SEL request. * @u1sel: parameter from Set SEL request. @@ -895,7 +897,10 @@ struct dwc3 { struct phy *usb2_generic_phy; struct phy *usb3_generic_phy; + bool phys_ready; + struct ulpi *ulpi; + bool ulpi_ready; void __iomem *regs; size_t regs_size; -- 2.16.1

6 years, 11 months

1
0
0 0

patch "usb: renesas_usbhs: missed the "running" flag in usb_dmac with rx" added to usb-linus

by gregkh＠linuxfoundation.org

This is a note to let you know that I've just added the patch titled usb: renesas_usbhs: missed the "running" flag in usb_dmac with rx to my usb git tree which can be found at git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb.git in the usb-linus branch. The patch will show up in the next release of the linux-next tree (usually sometime within the next 24 hours during the week.) The patch will hopefully also be merged in Linus's tree for the next -rc kernel release. If you have any questions about this process, please let me know. >From 17aa31f13cad25daa19d3f923323f552e87bc874 Mon Sep 17 00:00:00 2001 From: Yoshihiro Shimoda <yoshihiro.shimoda.uh(a)renesas.com> Date: Mon, 5 Feb 2018 17:12:35 +0900 Subject: usb: renesas_usbhs: missed the "running" flag in usb_dmac with rx path This fixes an issue that a gadget driver (usb_f_fs) is possible to stop rx transactions after the usb-dmac is used because the following functions missed to set/check the "running" flag. - usbhsf_dma_prepare_pop_with_usb_dmac() - usbhsf_dma_pop_done_with_usb_dmac() So, if next transaction uses pio, the usbhsf_prepare_pop() can not start the transaction because the "running" flag is 0. Fixes: 8355b2b3082d ("usb: renesas_usbhs: fix the behavior of some usbhs_pkt_handle") Cc: <stable(a)vger.kernel.org> # v3.19+ Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh(a)renesas.com> Signed-off-by: Felipe Balbi <felipe.balbi(a)linux.intel.com> --- drivers/usb/renesas_usbhs/fifo.c | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/drivers/usb/renesas_usbhs/fifo.c b/drivers/usb/renesas_usbhs/fifo.c index 5925d111bd47..39fa2fc1b8b7 100644 --- a/drivers/usb/renesas_usbhs/fifo.c +++ b/drivers/usb/renesas_usbhs/fifo.c @@ -982,6 +982,10 @@ static int usbhsf_dma_prepare_pop_with_usb_dmac(struct usbhs_pkt *pkt, if ((uintptr_t)pkt->buf & (USBHS_USB_DMAC_XFER_SIZE - 1)) goto usbhsf_pio_prepare_pop; + /* return at this time if the pipe is running */ + if (usbhs_pipe_is_running(pipe)) + return 0; + usbhs_pipe_config_change_bfre(pipe, 1); ret = usbhsf_fifo_select(pipe, fifo, 0); @@ -1172,6 +1176,7 @@ static int usbhsf_dma_pop_done_with_usb_dmac(struct usbhs_pkt *pkt, usbhsf_fifo_clear(pipe, fifo); pkt->actual = usbhs_dma_calc_received_size(pkt, chan, rcv_len); + usbhs_pipe_running(pipe, 0); usbhsf_dma_stop(pipe, fifo); usbhsf_dma_unmap(pkt); usbhsf_fifo_unselect(pipe, pipe->fifo); -- 2.16.1

6 years, 11 months

1
0
0 0

patch "usb: phy: mxs: Fix NULL pointer dereference on i.MX23/28" added to usb-linus

by gregkh＠linuxfoundation.org

This is a note to let you know that I've just added the patch titled usb: phy: mxs: Fix NULL pointer dereference on i.MX23/28 to my usb git tree which can be found at git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb.git in the usb-linus branch. The patch will show up in the next release of the linux-next tree (usually sometime within the next 24 hours during the week.) The patch will hopefully also be merged in Linus's tree for the next -rc kernel release. If you have any questions about this process, please let me know. >From 499350865387f8b8c40a9e9453a9a7eb3cec5dc4 Mon Sep 17 00:00:00 2001 From: Fabio Estevam <fabio.estevam(a)nxp.com> Date: Thu, 18 Jan 2018 00:22:45 -0200 Subject: usb: phy: mxs: Fix NULL pointer dereference on i.MX23/28 Commit e93650994a95 ("usb: phy: mxs: add usb charger type detection") causes the following kernel hang on i.MX28: [ 2.207973] usbcore: registered new interface driver usb-storage [ 2.235659] Unable to handle kernel NULL pointer dereference at virtual address 00000188 [ 2.244195] pgd = (ptrval) [ 2.246994] [00000188] *pgd=00000000 [ 2.250676] Internal error: Oops: 5 [#1] ARM [ 2.254979] Modules linked in: [ 2.258089] CPU: 0 PID: 1 Comm: swapper Not tainted 4.15.0-rc8-next-20180117-00002-g75d5f21 #7 [ 2.266724] Hardware name: Freescale MXS (Device Tree) [ 2.271921] PC is at regmap_read+0x0/0x5c [ 2.275977] LR is at mxs_phy_charger_detect+0x34/0x1dc mxs_phy_charger_detect() makes accesses to the anatop registers via regmap, however i.MX23/28 do not have such registers, which causes a NULL pointer dereference. Fix the issue by doing a NULL check on the 'regmap' pointer. Fixes: e93650994a95 ("usb: phy: mxs: add usb charger type detection") Cc: <stable(a)vger.kernel.org> # v4.15 Reviewed-by: Li Jun <jun.li(a)nxp.com> Acked-by: Peter Chen <peter.chen(a)nxp.com> Signed-off-by: Fabio Estevam <fabio.estevam(a)nxp.com> Signed-off-by: Felipe Balbi <felipe.balbi(a)linux.intel.com> --- drivers/usb/phy/phy-mxs-usb.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/usb/phy/phy-mxs-usb.c b/drivers/usb/phy/phy-mxs-usb.c index da031c45395a..fbec863350f6 100644 --- a/drivers/usb/phy/phy-mxs-usb.c +++ b/drivers/usb/phy/phy-mxs-usb.c @@ -602,6 +602,9 @@ static enum usb_charger_type mxs_phy_charger_detect(struct usb_phy *phy) void __iomem *base = phy->io_priv; enum usb_charger_type chgr_type = UNKNOWN_TYPE; + if (!regmap) + return UNKNOWN_TYPE; + if (mxs_charger_data_contact_detect(mxs_phy)) return chgr_type; -- 2.16.1

6 years, 11 months

1
0
0 0

[PATCH v2] megaraid_sas: Do not use 32-bit atomic request descriptor for Ventura controllers

by Shivasharan S

Problem Statement: Sending I/O through 32 bit descriptors to Ventura series of controller results in IO timeout on certain conditions. This error only occurs on systems with high I/O activity on Ventura series controllers. Changes in this patch will prevent driver from using 32 bit descriptor and use 64 bit Descriptors. Cc: <stable(a)vger.kernel.org> Signed-off-by: Kashyap Desai <kashyap.desai(a)broadcom.com> Signed-off-by: Shivasharan S <shivasharan.srikanteshwara(a)broadcom.com> Reviewed-by: Hannes Reinecke <hare(a)suse.com> Reviewed-by: Tomas Henzl <thenzl(a)redhat.com> --- Changes in v2: Removed below text from function description: * Ventura supports 32 bit Descriptor. * Prior to Ventura (12G) MR controller supports 64 bit Descriptor. drivers/scsi/megaraid/megaraid_sas_fusion.c | 42 ++++++++++------------------- 1 file changed, 14 insertions(+), 28 deletions(-) diff --git a/drivers/scsi/megaraid/megaraid_sas_fusion.c b/drivers/scsi/megaraid/megaraid_sas_fusion.c index 073ced07e662..dc8e850fbfd2 100644 --- a/drivers/scsi/megaraid/megaraid_sas_fusion.c +++ b/drivers/scsi/megaraid/megaraid_sas_fusion.c @@ -216,36 +216,30 @@ inline void megasas_return_cmd_fusion(struct megasas_instance *instance, /** * megasas_fire_cmd_fusion - Sends command to the FW * @instance: Adapter soft state - * @req_desc: 32bit or 64bit Request descriptor + * @req_desc: 64bit Request descriptor * - * Perform PCI Write. Ventura supports 32 bit Descriptor. - * Prior to Ventura (12G) MR controller supports 64 bit Descriptor. + * Perform PCI Write. */ static void megasas_fire_cmd_fusion(struct megasas_instance *instance, union MEGASAS_REQUEST_DESCRIPTOR_UNION *req_desc) { - if (instance->adapter_type == VENTURA_SERIES) - writel(le32_to_cpu(req_desc->u.low), - &instance->reg_set->inbound_single_queue_port); - else { #if defined(writeq) && defined(CONFIG_64BIT) - u64 req_data = (((u64)le32_to_cpu(req_desc->u.high) << 32) | - le32_to_cpu(req_desc->u.low)); + u64 req_data = (((u64)le32_to_cpu(req_desc->u.high) << 32) | + le32_to_cpu(req_desc->u.low)); - writeq(req_data, &instance->reg_set->inbound_low_queue_port); + writeq(req_data, &instance->reg_set->inbound_low_queue_port); #else - unsigned long flags; - spin_lock_irqsave(&instance->hba_lock, flags); - writel(le32_to_cpu(req_desc->u.low), - &instance->reg_set->inbound_low_queue_port); - writel(le32_to_cpu(req_desc->u.high), - &instance->reg_set->inbound_high_queue_port); - mmiowb(); - spin_unlock_irqrestore(&instance->hba_lock, flags); + unsigned long flags; + spin_lock_irqsave(&instance->hba_lock, flags); + writel(le32_to_cpu(req_desc->u.low), + &instance->reg_set->inbound_low_queue_port); + writel(le32_to_cpu(req_desc->u.high), + &instance->reg_set->inbound_high_queue_port); + mmiowb(); + spin_unlock_irqrestore(&instance->hba_lock, flags); #endif - } } /** @@ -982,7 +976,6 @@ megasas_ioc_init_fusion(struct megasas_instance *instance) const char *sys_info; MFI_CAPABILITIES *drv_ops; u32 scratch_pad_2; - unsigned long flags; ktime_t time; bool cur_fw_64bit_dma_capable; @@ -1121,14 +1114,7 @@ megasas_ioc_init_fusion(struct megasas_instance *instance) break; } - /* For Ventura also IOC INIT required 64 bit Descriptor write. */ - spin_lock_irqsave(&instance->hba_lock, flags); - writel(le32_to_cpu(req_desc.u.low), - &instance->reg_set->inbound_low_queue_port); - writel(le32_to_cpu(req_desc.u.high), - &instance->reg_set->inbound_high_queue_port); - mmiowb(); - spin_unlock_irqrestore(&instance->hba_lock, flags); + megasas_fire_cmd_fusion(instance, &req_desc); wait_and_poll(instance, cmd, MFI_POLL_TIMEOUT_SECS); -- 2.16.1

6 years, 11 months

2
1
0 0

[Linux-stable-mirror] [PATCH] IB/srp: Fix completion vector assignment algorithm

by Bart Van Assche

Ensure that cv_end is equal to ibdev->num_comp_vectors for the NUMA node with the highest index. This patch improves spreading of RDMA channels over completion vectors and thereby improves performance, especially on systems with only a single NUMA node. This patch drops support for the comp_vector login parameter by ignoring the value of that parameter since I have not found a good way to combine support for that parameter and automatic spreading of RDMA channels over completion vectors. Fixes: d92c0da71a35 ("IB/srp: Add multichannel support") Reported-by: Alexander Schmid <alex(a)modula-shop-systems.de> Signed-off-by: Bart Van Assche <bart.vanassche(a)wdc.com> Cc: Alexander Schmid <alex(a)modula-shop-systems.de> Cc: stable(a)vger.kernel.org --- drivers/infiniband/ulp/srp/ib_srp.c | 10 ++++------ 1 file changed, 4 insertions(+), 6 deletions(-) diff --git a/drivers/infiniband/ulp/srp/ib_srp.c b/drivers/infiniband/ulp/srp/ib_srp.c index b48843833d69..241c0e72dce3 100644 --- a/drivers/infiniband/ulp/srp/ib_srp.c +++ b/drivers/infiniband/ulp/srp/ib_srp.c @@ -3871,12 +3871,10 @@ static ssize_t srp_create_target(struct device *dev, num_online_nodes()); const int ch_end = ((node_idx + 1) * target->ch_count / num_online_nodes()); - const int cv_start = (node_idx * ibdev->num_comp_vectors / - num_online_nodes() + target->comp_vector) - % ibdev->num_comp_vectors; - const int cv_end = ((node_idx + 1) * ibdev->num_comp_vectors / - num_online_nodes() + target->comp_vector) - % ibdev->num_comp_vectors; + const int cv_start = node_idx * ibdev->num_comp_vectors / + num_online_nodes(); + const int cv_end = (node_idx + 1) * ibdev->num_comp_vectors / + num_online_nodes(); int cpu_idx = 0; for_each_online_cpu(cpu) { -- 2.16.1

6 years, 11 months

2
1
0 0

[PATCH] linux/nospec.h: allow index argument to have const-qualified type

by Rasmus Villemoes

The last expression in a statement expression need not be a bare variable, quoting gcc docs The last thing in the compound statement should be an expression followed by a semicolon; the value of this subexpression serves as the value of the entire construct. and we already use that in e.g. the min/max macros which end with a ternary expression. This way, we can allow index to have const-qualified type, which will in some cases avoid the need for introducing a local copy of index of non-const qualified type. That, in turn, can prevent readers not familiar with the internals of array_index_nospec from wondering about the seemingly redundant extra variable, and I think that's worthwhile considering how confusing the whole _nospec business is. The expression _i&_mask has type unsigned long (since that is the type of _mask, and the BUILD_BUG_ONs guarantee that _i will get promoted to that), so in order not to change the type of the whole expression, add a cast back to typeof(_i). Cc: stable(a)vger.kernel.org Signed-off-by: Rasmus Villemoes <linux(a)rasmusvillemoes.dk> --- cc stable because if this is ok, there will probably be future users relying on this which also get cc'ed to -stable. include/linux/nospec.h | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/include/linux/nospec.h b/include/linux/nospec.h index fbc98e2c8228..132e3f5a2e0d 100644 --- a/include/linux/nospec.h +++ b/include/linux/nospec.h @@ -72,7 +72,6 @@ static inline unsigned long array_index_mask_nospec(unsigned long index, BUILD_BUG_ON(sizeof(_i) > sizeof(long)); \ BUILD_BUG_ON(sizeof(_s) > sizeof(long)); \ \ - _i &= _mask; \ - _i; \ + (typeof(_i)) (_i & _mask); \ }) #endif /* _LINUX_NOSPEC_H */ -- 2.15.1

6 years, 11 months

3
4
0 0

2025

2024

2023

2022

2021

2020

2019

2018

2017

Linux-stable-mirror February 2018