In cpufreq basic selftests, one of the testcases is to read all cpufreq sysfs files and print the values. This testcase assumes all the cpufreq sysfs files have read permissions. However certain cpufreq sysfs files (eg. stats/reset) are write only files and this testcase errors out when it is not able to read the file. Similarily, there is one more testcase which reads the cpufreq sysfs file data and write it back to same file. This testcase also errors out for sysfs files without read permission. Fix these testcases by adding proper read permission checks.
Reported-by: Narasimhan V narasimhan.v@amd.com Signed-off-by: Swapnil Sapkal swapnil.sapkal@amd.com --- tools/testing/selftests/cpufreq/cpufreq.sh | 15 +++++++++++---- 1 file changed, 11 insertions(+), 4 deletions(-)
diff --git a/tools/testing/selftests/cpufreq/cpufreq.sh b/tools/testing/selftests/cpufreq/cpufreq.sh index e350c521b467..3484fa34e8d8 100755 --- a/tools/testing/selftests/cpufreq/cpufreq.sh +++ b/tools/testing/selftests/cpufreq/cpufreq.sh @@ -52,7 +52,14 @@ read_cpufreq_files_in_dir() for file in $files; do if [ -f $1/$file ]; then printf "$file:" - cat $1/$file + #file is readable ? + local rfile=$(ls -l $1/$file | awk '$1 ~ /^.*r.*/ { print $NF; }') + + if [ ! -z $rfile ]; then + cat $1/$file + else + printf "$file is not readable\n" + fi else printf "\n" read_cpufreq_files_in_dir "$1/$file" @@ -83,10 +90,10 @@ update_cpufreq_files_in_dir()
for file in $files; do if [ -f $1/$file ]; then - # file is writable ? - local wfile=$(ls -l $1/$file | awk '$1 ~ /^.*w.*/ { print $NF; }') + # file is readable and writable ? + local rwfile=$(ls -l $1/$file | awk '$1 ~ /^.*rw.*/ { print $NF; }')
- if [ ! -z $wfile ]; then + if [ ! -z $rwfile ]; then # scaling_setspeed is a special file and we # should skip updating it if [ $file != "scaling_setspeed" ]; then
On 30-04-25, 17:14, Swapnil Sapkal wrote:
In cpufreq basic selftests, one of the testcases is to read all cpufreq sysfs files and print the values. This testcase assumes all the cpufreq sysfs files have read permissions. However certain cpufreq sysfs files (eg. stats/reset) are write only files and this testcase errors out when it is not able to read the file. Similarily, there is one more testcase which reads the cpufreq sysfs file data and write it back to same file. This testcase also errors out for sysfs files without read permission. Fix these testcases by adding proper read permission checks.
Reported-by: Narasimhan V narasimhan.v@amd.com Signed-off-by: Swapnil Sapkal swapnil.sapkal@amd.com
tools/testing/selftests/cpufreq/cpufreq.sh | 15 +++++++++++---- 1 file changed, 11 insertions(+), 4 deletions(-)
diff --git a/tools/testing/selftests/cpufreq/cpufreq.sh b/tools/testing/selftests/cpufreq/cpufreq.sh index e350c521b467..3484fa34e8d8 100755 --- a/tools/testing/selftests/cpufreq/cpufreq.sh +++ b/tools/testing/selftests/cpufreq/cpufreq.sh @@ -52,7 +52,14 @@ read_cpufreq_files_in_dir() for file in $files; do if [ -f $1/$file ]; then printf "$file:"
cat $1/$file
#file is readable ?
local rfile=$(ls -l $1/$file | awk '$1 ~ /^.*r.*/ { print $NF; }')
if [ ! -z $rfile ]; then
cat $1/$file
else
printf "$file is not readable\n"
fi
What about:
if [ -r $1/$file ]; then cat $1/$file else printf "$file is not readable\n" fi
Hi Viresh,
On 5/19/2025 1:28 PM, Viresh Kumar wrote:
On 30-04-25, 17:14, Swapnil Sapkal wrote:
In cpufreq basic selftests, one of the testcases is to read all cpufreq sysfs files and print the values. This testcase assumes all the cpufreq sysfs files have read permissions. However certain cpufreq sysfs files (eg. stats/reset) are write only files and this testcase errors out when it is not able to read the file. Similarily, there is one more testcase which reads the cpufreq sysfs file data and write it back to same file. This testcase also errors out for sysfs files without read permission. Fix these testcases by adding proper read permission checks.
Reported-by: Narasimhan V narasimhan.v@amd.com Signed-off-by: Swapnil Sapkal swapnil.sapkal@amd.com
tools/testing/selftests/cpufreq/cpufreq.sh | 15 +++++++++++---- 1 file changed, 11 insertions(+), 4 deletions(-)
diff --git a/tools/testing/selftests/cpufreq/cpufreq.sh b/tools/testing/selftests/cpufreq/cpufreq.sh index e350c521b467..3484fa34e8d8 100755 --- a/tools/testing/selftests/cpufreq/cpufreq.sh +++ b/tools/testing/selftests/cpufreq/cpufreq.sh @@ -52,7 +52,14 @@ read_cpufreq_files_in_dir() for file in $files; do if [ -f $1/$file ]; then printf "$file:"
cat $1/$file
#file is readable ?
local rfile=$(ls -l $1/$file | awk '$1 ~ /^.*r.*/ { print $NF; }')
if [ ! -z $rfile ]; then
cat $1/$file
else
printf "$file is not readable\n"
fi
What about:
if [ -r $1/$file ]; then cat $1/$file else printf "$file is not readable\n" fi
Initially I tried the same, but it does not work properly with the root user.
-- Thanks and Regards, Swapnil
On 22-05-25, 14:07, Sapkal, Swapnil wrote:
Initially I tried the same, but it does not work properly with the root user.
Hmm,
Tried chatgpt now and it says this should work:
if ! cat "$1/$file" 2>/dev/null; then printf "$file is not readable\n" fi
- This attempts to read the file. - If it fails, the cat command returns non-zero, and you print a message. - 2>/dev/null suppresses error messages (Permission denied, etc.) - This works reliably for both root and non-root users, because it actually tests the read action, not just permission bits.
Hi Viresh,
On 5/22/2025 3:15 PM, Viresh Kumar wrote:
On 22-05-25, 14:07, Sapkal, Swapnil wrote:
Initially I tried the same, but it does not work properly with the root user.
Hmm,
Tried chatgpt now and it says this should work:
if ! cat "$1/$file" 2>/dev/null; then printf "$file is not readable\n" fi
- This attempts to read the file.
- If it fails, the cat command returns non-zero, and you print a message.
- 2>/dev/null suppresses error messages (Permission denied, etc.)
- This works reliably for both root and non-root users, because it actually tests the read action, not just permission bits.
This looks clean. I will send v2 with this change.
-- Thanks and Regards, Swapnil
On 5/19/25 01:58, Viresh Kumar wrote:
On 30-04-25, 17:14, Swapnil Sapkal wrote:
In cpufreq basic selftests, one of the testcases is to read all cpufreq sysfs files and print the values. This testcase assumes all the cpufreq sysfs files have read permissions. However certain cpufreq sysfs files (eg. stats/reset) are write only files and this testcase errors out when it is not able to read the file. Similarily, there is one more testcase which reads the cpufreq sysfs file data and write it back to same file. This testcase also errors out for sysfs files without read permission. Fix these testcases by adding proper read permission checks.
Can you share how you ran the test?
Reported-by: Narasimhan V narasimhan.v@amd.com Signed-off-by: Swapnil Sapkal swapnil.sapkal@amd.com
tools/testing/selftests/cpufreq/cpufreq.sh | 15 +++++++++++---- 1 file changed, 11 insertions(+), 4 deletions(-)
diff --git a/tools/testing/selftests/cpufreq/cpufreq.sh b/tools/testing/selftests/cpufreq/cpufreq.sh index e350c521b467..3484fa34e8d8 100755 --- a/tools/testing/selftests/cpufreq/cpufreq.sh +++ b/tools/testing/selftests/cpufreq/cpufreq.sh @@ -52,7 +52,14 @@ read_cpufreq_files_in_dir() for file in $files; do if [ -f $1/$file ]; then printf "$file:"
cat $1/$file
#file is readable ?
local rfile=$(ls -l $1/$file | awk '$1 ~ /^.*r.*/ { print $NF; }')
if [ ! -z $rfile ]; then
cat $1/$file
else
printf "$file is not readable\n"
fi
What about:
if [ -r $1/$file ]; then cat $1/$file else printf "$file is not readable\n" fi
thanks, -- Shuah
Hi Shuah,
On 5/22/2025 8:47 PM, Shuah Khan wrote:
On 5/19/25 01:58, Viresh Kumar wrote:
On 30-04-25, 17:14, Swapnil Sapkal wrote:
In cpufreq basic selftests, one of the testcases is to read all cpufreq sysfs files and print the values. This testcase assumes all the cpufreq sysfs files have read permissions. However certain cpufreq sysfs files (eg. stats/reset) are write only files and this testcase errors out when it is not able to read the file. Similarily, there is one more testcase which reads the cpufreq sysfs file data and write it back to same file. This testcase also errors out for sysfs files without read permission. Fix these testcases by adding proper read permission checks.
Can you share how you ran the test?
I ran the basic tests with the following command:
./main.sh -t basic
Reported-by: Narasimhan V narasimhan.v@amd.com Signed-off-by: Swapnil Sapkal swapnil.sapkal@amd.com
tools/testing/selftests/cpufreq/cpufreq.sh | 15 +++++++++++---- 1 file changed, 11 insertions(+), 4 deletions(-)
diff --git a/tools/testing/selftests/cpufreq/cpufreq.sh b/tools/testing/selftests/cpufreq/cpufreq.sh index e350c521b467..3484fa34e8d8 100755 --- a/tools/testing/selftests/cpufreq/cpufreq.sh +++ b/tools/testing/selftests/cpufreq/cpufreq.sh @@ -52,7 +52,14 @@ read_cpufreq_files_in_dir() for file in $files; do if [ -f $1/$file ]; then printf "$file:" - cat $1/$file + #file is readable ? + local rfile=$(ls -l $1/$file | awk '$1 ~ /^.*r.*/ { print $NF; }')
+ if [ ! -z $rfile ]; then + cat $1/$file + else + printf "$file is not readable\n" + fi
What about:
if [ -r $1/$file ]; then cat $1/$file else printf "$file is not readable\n" fi
thanks, -- Shuah
-- Thanks and Regards, Swapnil
linux-kselftest-mirror@lists.linaro.org