- Linux-kselftest-mirror - lists.linaro.org

[PATCH 0/4] kselftest/arm64: fp-ptrace enhancements

by Mark Brown

This series contains a bit of a grab bag of improvements to the floating point tests, mainly fp-ptrace. Globally over all the tests we start using defines from the generated sysregs (following the example of the KVM selftests) for SVCR, stop being quite so wasteful with registers when calling into the assembler code then expand the coverage of both ZA writes and FPMR (which was not there since fp-ptrace and the 2023 dpISA extensions were on the list at the same time). Signed-off-by: Mark Brown <broonie(a)kernel.org> --- Mark Brown (4): kselftets/arm64: Use flag bits for features in fp-ptrace assembler code kselftest/arm64: Use a define for SVCR kselftest/arm64: Expand the set of ZA writes fp-ptrace does kselftest/arm64: Add FPMR coverage to fp-ptrace tools/testing/selftests/arm64/fp/Makefile | 20 ++- tools/testing/selftests/arm64/fp/fp-ptrace-asm.S | 52 +++++--- tools/testing/selftests/arm64/fp/fp-ptrace.c | 155 +++++++++++++++++++++-- tools/testing/selftests/arm64/fp/fp-ptrace.h | 16 ++- tools/testing/selftests/arm64/fp/sve-test.S | 5 +- tools/testing/selftests/arm64/fp/za-fork-asm.S | 3 +- tools/testing/selftests/arm64/fp/za-test.S | 6 +- tools/testing/selftests/arm64/fp/zt-test.S | 5 +- 8 files changed, 213 insertions(+), 49 deletions(-) --- base-commit: 8e929cb546ee42c9a61d24fae60605e9e3192354 change-id: 20241105-arm64-fp-ptrace-fpmr-ff061facd3da Best regards, -- Mark Brown <broonie(a)kernel.org>

11 months, 4 weeks

2
6
0 0

[PATCH] kunit: skb: add gfp to kernel doc for kunit_zalloc_skb()

by Dan Carpenter

Kuan-Wei Chiu pointed out that the kernel doc for kunit_zalloc_skb() needs to include the @gfp information. Add it. Reported-by: Kuan-Wei Chiu <visitorckw(a)gmail.com> Closes: https://lore.kernel.org/all/Zy+VIXDPuU613fFd@visitorckw-System-Product-Name/ Signed-off-by: Dan Carpenter <dan.carpenter(a)linaro.org> --- include/kunit/skbuff.h | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/include/kunit/skbuff.h b/include/kunit/skbuff.h index 345e1e8f0312..07784694357c 100644 --- a/include/kunit/skbuff.h +++ b/include/kunit/skbuff.h @@ -20,8 +20,9 @@ static void kunit_action_kfree_skb(void *p) * kunit_zalloc_skb() - Allocate and initialize a resource managed skb. * @test: The test case to which the skb belongs * @len: size to allocate + * @gfp: allocation flags * - * Allocate a new struct sk_buff with GFP_KERNEL, zero fill the give length + * Allocate a new struct sk_buff with gfp flags, zero fill the given length * and add it as a resource to the kunit test for automatic cleanup. * * Returns: newly allocated SKB, or %NULL on error -- 2.45.2

11 months, 4 weeks

3
2
0 0

[PATCH net-next v2 0/8] net: Improve netns handling in RTNL and ip_tunnel

by Xiao Liang

This patch series includes some netns-related improvements and fixes for RTNL and ip_tunnel, to make link creation more intuitive: - Creating link in another net namespace doesn't conflict with link names in current one. - Add a flag in rtnl_ops, to avoid netns change when link-netns is present if possible. - When creating ip tunnel (e.g. GRE) in another netns, use current as link-netns if not specified explicitly. So that # modprobe ip_gre netns_atomic=1 # ip link add netns ns1 link-netns ns2 tun0 type gre ... will create tun0 in ns1, rather than create it in ns2 and move to ns1. And don't conflict with another interface named "tun0" in current netns. --- v2: - Check NLM_F_EXCL to ensure only link creation is affected. - Add self tests for link name/ifindex conflict and notifications in different netns. - Changes in dummy driver and ynl in order to add the test case. v1: link: https://lore.kernel.org/all/20241023023146.372653-1-shaw.leon@gmail.com/ Xiao Liang (8): rtnetlink: Lookup device in target netns when creating link rtnetlink: Add netns_atomic flag in rtnl_link_ops net: ip_tunnel: Build flow in underlay net namespace net: ip_tunnel: Add source netns support for newlink net: ip_gre: Add netns_atomic module parameter net: dummy: Set netns_atomic in rtnl ops for testing tools/net/ynl: Add retry limit for async notification selftests: net: Add two test cases for link netns drivers/net/dummy.c | 1 + include/net/ip_tunnels.h | 3 ++ include/net/rtnetlink.h | 3 ++ net/core/rtnetlink.c | 17 +++++-- net/ipv4/ip_gre.c | 15 +++++- net/ipv4/ip_tunnel.c | 27 +++++++---- tools/net/ynl/lib/ynl.py | 7 ++- tools/testing/selftests/net/Makefile | 1 + tools/testing/selftests/net/netns-name.sh | 10 ++++ tools/testing/selftests/net/netns_atomic.py | 54 +++++++++++++++++++++ 10 files changed, 121 insertions(+), 17 deletions(-) create mode 100755 tools/testing/selftests/net/netns_atomic.py -- 2.47.0

11 months, 4 weeks

4
25
0 0

[PATCH net-next v10] net: ipv4: Cache pmtu for all packet paths if multipath enabled

by Vladimir Vdovin

Check number of paths by fib_info_num_path(), and update_or_create_fnhe() for every path. Problem is that pmtu is cached only for the oif that has received icmp message "need to frag", other oifs will still try to use "default" iface mtu. An example topology showing the problem: | host1 +---------+ | dummy0 | 10.179.20.18/32 mtu9000 +---------+ +-----------+----------------+ +---------+ +---------+ | ens17f0 | 10.179.2.141/31 | ens17f1 | 10.179.2.13/31 +---------+ +---------+ | (all here have mtu 9000) | +------+ +------+ | ro1 | 10.179.2.140/31 | ro2 | 10.179.2.12/31 +------+ +------+ | | ---------+------------+-------------------+------ | +-----+ | ro3 | 10.10.10.10 mtu1500 +-----+ | ======================================== some networks ======================================== | +-----+ | eth0| 10.10.30.30 mtu9000 +-----+ | host2 host1 have enabled multipath and sysctl net.ipv4.fib_multipath_hash_policy = 1: default proto static src 10.179.20.18 nexthop via 10.179.2.12 dev ens17f1 weight 1 nexthop via 10.179.2.140 dev ens17f0 weight 1 When host1 tries to do pmtud from 10.179.20.18/32 to host2, host1 receives at ens17f1 iface an icmp packet from ro3 that ro3 mtu=1500. And host1 caches it in nexthop exceptions cache. Problem is that it is cached only for the iface that has received icmp, and there is no way that ro3 will send icmp msg to host1 via another path. Host1 now have this routes to host2: ip r g 10.10.30.30 sport 30000 dport 443 10.10.30.30 via 10.179.2.12 dev ens17f1 src 10.179.20.18 uid 0 cache expires 521sec mtu 1500 ip r g 10.10.30.30 sport 30033 dport 443 10.10.30.30 via 10.179.2.140 dev ens17f0 src 10.179.20.18 uid 0 cache So when host1 tries again to reach host2 with mtu>1500, if packet flow is lucky enough to be hashed with oif=ens17f1 its ok, if oif=ens17f0 it blackholes and still gets icmp msgs from ro3 to ens17f1, until lucky day when ro3 will send it through another flow to ens17f0. Signed-off-by: Vladimir Vdovin <deliran(a)verdict.gg> --- V10: selfttests in pmtu.sh: - remove unused fail var - Flip error messages V9: selftests in pmtu.sh: - remove useless return - fix mtu var override V8: selftests in pmtu.sh: - Change var names from "dummy" to "host" - Fix errors caused by incorrect iface arguments pass - Add src addr to setup_multipath_new - Change multipath* func order - Change route_get_dst_exception() && route_get_dst_pmtu_from_exception() and arguments pass where they are used as Ido suggested in https://lore.kernel.org/all/ZykH_fdcMBdFgXix@shredder/ V7: selftest in pmtu.sh: - add setup_multipath() with old and new nh tests - add global "dummy_v4" addr variables - add documentation - remove dummy netdev usage in mp nh test - remove useless sysctl opts in mp nh test V6: - make commit message cleaner V5: - make self test cleaner V4: - fix selftest, do route lookup before checking cached exceptions V3: - add selftest - fix compile error V2: - fix fib_info_num_path parameter pass --- net/ipv4/route.c | 13 ++++ tools/testing/selftests/net/pmtu.sh | 112 +++++++++++++++++++++++----- 2 files changed, 108 insertions(+), 17 deletions(-) diff --git a/net/ipv4/route.c b/net/ipv4/route.c index 723ac9181558..652f603d29fe 100644 --- a/net/ipv4/route.c +++ b/net/ipv4/route.c @@ -1027,6 +1027,19 @@ static void __ip_rt_update_pmtu(struct rtable *rt, struct flowi4 *fl4, u32 mtu) struct fib_nh_common *nhc; fib_select_path(net, &res, fl4, NULL); +#ifdef CONFIG_IP_ROUTE_MULTIPATH + if (fib_info_num_path(res.fi) > 1) { + int nhsel; + + for (nhsel = 0; nhsel < fib_info_num_path(res.fi); nhsel++) { + nhc = fib_info_nhc(res.fi, nhsel); + update_or_create_fnhe(nhc, fl4->daddr, 0, mtu, lock, + jiffies + net->ipv4.ip_rt_mtu_expires); + } + rcu_read_unlock(); + return; + } +#endif /* CONFIG_IP_ROUTE_MULTIPATH */ nhc = FIB_RES_NHC(res); update_or_create_fnhe(nhc, fl4->daddr, 0, mtu, lock, jiffies + net->ipv4.ip_rt_mtu_expires); diff --git a/tools/testing/selftests/net/pmtu.sh b/tools/testing/selftests/net/pmtu.sh index 569bce8b6383..7ca2fbd971ae 100755 --- a/tools/testing/selftests/net/pmtu.sh +++ b/tools/testing/selftests/net/pmtu.sh @@ -197,6 +197,12 @@ # # - pmtu_ipv6_route_change # Same as above but with IPv6 +# +# - pmtu_ipv4_mp_exceptions +# Use the same topology as in pmtu_ipv4, but add routeable addresses +# on host A and B on lo reachable via both routers. Host A and B +# addresses have multipath routes to each other, b_r1 mtu = 1500. +# Check that PMTU exceptions are created for both paths. source lib.sh source net_helper.sh @@ -266,7 +272,8 @@ tests=" list_flush_ipv4_exception ipv4: list and flush cached exceptions 1 list_flush_ipv6_exception ipv6: list and flush cached exceptions 1 pmtu_ipv4_route_change ipv4: PMTU exception w/route replace 1 - pmtu_ipv6_route_change ipv6: PMTU exception w/route replace 1" + pmtu_ipv6_route_change ipv6: PMTU exception w/route replace 1 + pmtu_ipv4_mp_exceptions ipv4: PMTU multipath nh exceptions 1" # Addressing and routing for tests with routers: four network segments, with # index SEGMENT between 1 and 4, a common prefix (PREFIX4 or PREFIX6) and an @@ -343,6 +350,9 @@ tunnel6_a_addr="fd00:2::a" tunnel6_b_addr="fd00:2::b" tunnel6_mask="64" +host4_a_addr="192.168.99.99" +host4_b_addr="192.168.88.88" + dummy6_0_prefix="fc00:1000::" dummy6_1_prefix="fc00:1001::" dummy6_mask="64" @@ -984,6 +994,52 @@ setup_ovs_bridge() { run_cmd ip route add ${prefix6}:${b_r1}::1 via ${prefix6}:${a_r1}::2 } +setup_multipath_new() { + # Set up host A with multipath routes to host B host4_b_addr + run_cmd ${ns_a} ip addr add ${host4_a_addr} dev lo + run_cmd ${ns_a} ip nexthop add id 401 via ${prefix4}.${a_r1}.2 dev veth_A-R1 + run_cmd ${ns_a} ip nexthop add id 402 via ${prefix4}.${a_r2}.2 dev veth_A-R2 + run_cmd ${ns_a} ip nexthop add id 403 group 401/402 + run_cmd ${ns_a} ip route add ${host4_b_addr} src ${host4_a_addr} nhid 403 + + # Set up host B with multipath routes to host A host4_a_addr + run_cmd ${ns_b} ip addr add ${host4_b_addr} dev lo + run_cmd ${ns_b} ip nexthop add id 401 via ${prefix4}.${b_r1}.2 dev veth_B-R1 + run_cmd ${ns_b} ip nexthop add id 402 via ${prefix4}.${b_r2}.2 dev veth_B-R2 + run_cmd ${ns_b} ip nexthop add id 403 group 401/402 + run_cmd ${ns_b} ip route add ${host4_a_addr} src ${host4_b_addr} nhid 403 +} + +setup_multipath_old() { + # Set up host A with multipath routes to host B host4_b_addr + run_cmd ${ns_a} ip addr add ${host4_a_addr} dev lo + run_cmd ${ns_a} ip route add ${host4_b_addr} \ + src ${host4_a_addr} \ + nexthop via ${prefix4}.${a_r1}.2 weight 1 \ + nexthop via ${prefix4}.${a_r2}.2 weight 1 + + # Set up host B with multipath routes to host A host4_a_addr + run_cmd ${ns_b} ip addr add ${host4_b_addr} dev lo + run_cmd ${ns_b} ip route add ${host4_a_addr} \ + src ${host4_b_addr} \ + nexthop via ${prefix4}.${b_r1}.2 weight 1 \ + nexthop via ${prefix4}.${b_r2}.2 weight 1 +} + +setup_multipath() { + if [ "$USE_NH" = "yes" ]; then + setup_multipath_new + else + setup_multipath_old + fi + + # Set up routers with routes to dummies + run_cmd ${ns_r1} ip route add ${host4_a_addr} via ${prefix4}.${a_r1}.1 + run_cmd ${ns_r2} ip route add ${host4_a_addr} via ${prefix4}.${a_r2}.1 + run_cmd ${ns_r1} ip route add ${host4_b_addr} via ${prefix4}.${b_r1}.1 + run_cmd ${ns_r2} ip route add ${host4_b_addr} via ${prefix4}.${b_r2}.1 +} + setup() { [ "$(id -u)" -ne 0 ] && echo " need to run as root" && return $ksft_skip @@ -1076,23 +1132,15 @@ link_get_mtu() { } route_get_dst_exception() { - ns_cmd="${1}" - dst="${2}" - dsfield="${3}" + ns_cmd="${1}"; shift - if [ -z "${dsfield}" ]; then - dsfield=0 - fi - - ${ns_cmd} ip route get "${dst}" dsfield "${dsfield}" + ${ns_cmd} ip route get "$@" } route_get_dst_pmtu_from_exception() { - ns_cmd="${1}" - dst="${2}" - dsfield="${3}" + ns_cmd="${1}"; shift - mtu_parse "$(route_get_dst_exception "${ns_cmd}" "${dst}" "${dsfield}")" + mtu_parse "$(route_get_dst_exception "${ns_cmd}" "$@")" } check_pmtu_value() { @@ -1235,10 +1283,10 @@ test_pmtu_ipv4_dscp_icmp_exception() { run_cmd "${ns_a}" ping -q -M want -Q "${dsfield}" -c 1 -w 1 -s "${len}" "${dst2}" # Check that exceptions have been created with the correct PMTU - pmtu_1="$(route_get_dst_pmtu_from_exception "${ns_a}" "${dst1}" "${policy_mark}")" + pmtu_1="$(route_get_dst_pmtu_from_exception "${ns_a}" "${dst1}" dsfield "${policy_mark}")" check_pmtu_value "1400" "${pmtu_1}" "exceeding MTU" || return 1 - pmtu_2="$(route_get_dst_pmtu_from_exception "${ns_a}" "${dst2}" "${policy_mark}")" + pmtu_2="$(route_get_dst_pmtu_from_exception "${ns_a}" "${dst2}" dsfield "${policy_mark}")" check_pmtu_value "1500" "${pmtu_2}" "exceeding MTU" || return 1 } @@ -1285,9 +1333,9 @@ test_pmtu_ipv4_dscp_udp_exception() { UDP:"${dst2}":50000,tos="${dsfield}" # Check that exceptions have been created with the correct PMTU - pmtu_1="$(route_get_dst_pmtu_from_exception "${ns_a}" "${dst1}" "${policy_mark}")" + pmtu_1="$(route_get_dst_pmtu_from_exception "${ns_a}" "${dst1}" dsfield "${policy_mark}")" check_pmtu_value "1400" "${pmtu_1}" "exceeding MTU" || return 1 - pmtu_2="$(route_get_dst_pmtu_from_exception "${ns_a}" "${dst2}" "${policy_mark}")" + pmtu_2="$(route_get_dst_pmtu_from_exception "${ns_a}" "${dst2}" dsfield "${policy_mark}")" check_pmtu_value "1500" "${pmtu_2}" "exceeding MTU" || return 1 } @@ -2329,6 +2377,36 @@ test_pmtu_ipv6_route_change() { test_pmtu_ipvX_route_change 6 } +test_pmtu_ipv4_mp_exceptions() { + setup namespaces routing multipath || return $ksft_skip + + trace "${ns_a}" veth_A-R1 "${ns_r1}" veth_R1-A \ + "${ns_r1}" veth_R1-B "${ns_b}" veth_B-R1 \ + "${ns_a}" veth_A-R2 "${ns_r2}" veth_R2-A \ + "${ns_r2}" veth_R2-B "${ns_b}" veth_B-R2 + + # Set up initial MTU values + mtu "${ns_a}" veth_A-R1 2000 + mtu "${ns_r1}" veth_R1-A 2000 + mtu "${ns_r1}" veth_R1-B 1500 + mtu "${ns_b}" veth_B-R1 1500 + + mtu "${ns_a}" veth_A-R2 2000 + mtu "${ns_r2}" veth_R2-A 2000 + mtu "${ns_r2}" veth_R2-B 1500 + mtu "${ns_b}" veth_B-R2 1500 + + # Ping and expect two nexthop exceptions for two routes + run_cmd ${ns_a} ping -q -M want -i 0.1 -c 1 -s 1800 "${host4_b_addr}" + + # Check that exceptions have been created with the correct PMTU + pmtu_a_R1="$(route_get_dst_pmtu_from_exception "${ns_a}" "${host4_b_addr}" oif veth_A-R1)" + pmtu_a_R2="$(route_get_dst_pmtu_from_exception "${ns_a}" "${host4_b_addr}" oif veth_A-R2)" + + check_pmtu_value "1500" "${pmtu_a_R1}" "exceeding MTU (veth_A-R1)" || return 1 + check_pmtu_value "1500" "${pmtu_a_R2}" "exceeding MTU (veth_A-R2)" || return 1 +} + usage() { echo echo "$0 [OPTIONS] [TEST]..." base-commit: 66600fac7a984dea4ae095411f644770b2561ede -- 2.43.5

11 months, 4 weeks

3
2
0 0

[PATCH net-next] net: netconsole: selftests: Check if netdevsim is available

by Breno Leitao

The netconsole selftest relies on the availability of the netdevsim module. To ensure the test can run correctly, we need to check if the netdevsim module is either loaded or built-in before proceeding. Update the netconsole selftest to check for the existence of the /sys/bus/netdevsim/new_device file before running the test. If the file is not found, the test is skipped with an explanation that the CONFIG_NETDEVSIM kernel config option may not be enabled. Signed-off-by: Breno Leitao <leitao(a)debian.org> --- tools/testing/selftests/drivers/net/netcons_basic.sh | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) diff --git a/tools/testing/selftests/drivers/net/netcons_basic.sh b/tools/testing/selftests/drivers/net/netcons_basic.sh index 182eb1a97e59f3b4c9eea0e5b9e64a7fff656e2b..b175f4d966e5056ddb62e335f212c03e55f50fb0 100755 --- a/tools/testing/selftests/drivers/net/netcons_basic.sh +++ b/tools/testing/selftests/drivers/net/netcons_basic.sh @@ -39,6 +39,7 @@ NAMESPACE="" # IDs for netdevsim NSIM_DEV_1_ID=$((256 + RANDOM % 256)) NSIM_DEV_2_ID=$((512 + RANDOM % 256)) +NSIM_DEV_SYS_NEW="/sys/bus/netdevsim/new_device" # Used to create and delete namespaces source "${SCRIPTDIR}"/../../net/lib.sh @@ -46,7 +47,6 @@ source "${SCRIPTDIR}"/../../net/net_helper.sh # Create netdevsim interfaces create_ifaces() { - local NSIM_DEV_SYS_NEW=/sys/bus/netdevsim/new_device echo "$NSIM_DEV_2_ID" > "$NSIM_DEV_SYS_NEW" echo "$NSIM_DEV_1_ID" > "$NSIM_DEV_SYS_NEW" @@ -212,6 +212,11 @@ function check_for_dependencies() { exit "${ksft_skip}" fi + if [ ! -f "${NSIM_DEV_SYS_NEW}" ]; then + echo "SKIP: file ${NSIM_DEV_SYS_NEW} does not exist. Check if CONFIG_NETDEVSIM is enabled" >&2 + exit "${ksft_skip}" + fi + if [ ! -d "${NETCONS_CONFIGFS}" ]; then echo "SKIP: directory ${NETCONS_CONFIGFS} does not exist. Check if NETCONSOLE_DYNAMIC is enabled" >&2 exit "${ksft_skip}" --- base-commit: 4861333b42178fa3d8fd1bb4e2cfb2fedc968dba change-id: 20241108-netcon_selftest_deps-83f26456f095 Best regards, -- Breno Leitao <leitao(a)debian.org>

11 months, 4 weeks

3
2
0 0

[PATCH net-next v9 0/6] Suspend IRQs during application busy periods

by Joe Damato

Greetings: Welcome to v9, see changelog below. This revision addresses feedback Willem gave on the selftests. No functional or code changes to the implementation were made and performance tests were not re-run. This series introduces a new mechanism, IRQ suspension, which allows network applications using epoll to mask IRQs during periods of high traffic while also reducing tail latency (compared to existing mechanisms, see below) during periods of low traffic. In doing so, this balances CPU consumption with network processing efficiency. Martin Karsten (CC'd) and I have been collaborating on this series for several months and have appreciated the feedback from the community on our RFC [1]. We've updated the cover letter and kernel documentation in an attempt to more clearly explain how this mechanism works, how applications can use it, and how it compares to existing mechanisms in the kernel. I briefly mentioned this idea at netdev conf 2024 (for those who were there) and Martin described this idea in an earlier paper presented at Sigmetrics 2024 [2]. ~ The short explanation (TL;DR) We propose adding a new napi config parameter: irq_suspend_timeout to help balance CPU usage and network processing efficiency when using IRQ deferral and napi busy poll. If this parameter is set to a non-zero value *and* a user application has enabled preferred busy poll on a busy poll context (via the EPIOCSPARAMS ioctl introduced in commit 18e2bf0edf4d ("eventpoll: Add epoll ioctl for epoll_params")), then application calls to epoll_wait for that context will cause device IRQs and softirq processing to be suspended as long as epoll_wait successfully retrieves data from the NAPI. Each time data is retrieved, the irq_suspend_timeout is deferred. If/when network traffic subsides and epoll_wait returns no data, IRQ suspension is immediately reverted back to the existing napi_defer_hard_irqs and gro_flush_timeout mechanism which was introduced in commit 6f8b12d661d0 ("net: napi: add hard irqs deferral feature")). The irq_suspend_timeout serves as a safety mechanism. If userland takes a long time processing data, irq_suspend_timeout will fire and restart normal NAPI processing. For a more in depth explanation, please continue reading. ~ Comparison with existing mechanisms Interrupt mitigation can be accomplished in napi software, by setting napi_defer_hard_irqs and gro_flush_timeout, or via interrupt coalescing in the NIC. This can be quite efficient, but in both cases, a fixed timeout (or packet count) needs to be configured. However, a fixed timeout cannot effectively support both low- and high-load situations: At low load, an application typically processes a few requests and then waits to receive more input data. In this scenario, a large timeout will cause unnecessary latency. At high load, an application typically processes many requests before being ready to receive more input data. In this case, a small timeout will likely fire prematurely and trigger irq/softirq processing, which interferes with the application's execution. This causes overhead, most likely due to cache contention. While NICs attempt to provide adaptive interrupt coalescing schemes, these cannot properly take into account application-level processing. An alternative packet delivery mechanism is busy-polling, which results in perfect alignment of application processing and network polling. It delivers optimal performance (throughput and latency), but results in 100% cpu utilization and is thus inefficient for below-capacity workloads. We propose to add a new packet delivery mode that properly alternates between busy polling and interrupt-based delivery depending on busy and idle periods of the application. During a busy period, the system operates in busy-polling mode, which avoids interference. During an idle period, the system falls back to interrupt deferral, but with a small timeout to avoid excessive latencies. This delivery mode can also be viewed as an extension of basic interrupt deferral, but alternating between a small and a very large timeout. This delivery mode is efficient, because it avoids softirq execution interfering with application processing during busy periods. It can be used with blocking epoll_wait to conserve cpu cycles during idle periods. The effect of alternating between busy and idle periods is that performance (throughput and latency) is very close to full busy polling, while cpu utilization is lower and very close to interrupt mitigation. ~ Usage details IRQ suspension is introduced via a per-NAPI configuration parameter that controls the maximum time that IRQs can be suspended. Here's how it is intended to work: - The user application (or system administrator) uses the netdev-genl netlink interface to set the pre-existing napi_defer_hard_irqs and gro_flush_timeout NAPI config parameters to enable IRQ deferral. - The user application (or system administrator) sets the proposed irq_suspend_timeout parameter via the netdev-genl netlink interface to a larger value than gro_flush_timeout to enable IRQ suspension. - The user application issues the existing epoll ioctl to set the prefer_busy_poll flag on the epoll context. - The user application then calls epoll_wait to busy poll for network events, as it normally would. - If epoll_wait returns events to userland, IRQs are suspended for the duration of irq_suspend_timeout. - If epoll_wait finds no events and the thread is about to go to sleep, IRQ handling using napi_defer_hard_irqs and gro_flush_timeout is resumed. As long as epoll_wait is retrieving events, IRQs (and softirq processing) for the NAPI being polled remain disabled. When network traffic reduces, eventually a busy poll loop in the kernel will retrieve no data. When this occurs, regular IRQ deferral using gro_flush_timeout for the polled NAPI is re-enabled. Unless IRQ suspension is continued by subsequent calls to epoll_wait, it automatically times out after the irq_suspend_timeout timer expires. Regular deferral is also immediately re-enabled when the epoll context is destroyed. ~ Usage scenario The target scenario for IRQ suspension as packet delivery mode is a system that runs a dominant application with substantial network I/O. The target application can be configured to receive input data up to a certain batch size (via epoll_wait maxevents parameter) and this batch size determines the worst-case latency that application requests might experience. Because packet delivery is suspended during the target application's processing, the batch size also determines the worst-case latency of concurrent applications using the same RX queue(s). gro_flush_timeout should be set as small as possible, but large enough to make sure that a single request is likely not being interfered with. irq_suspend_timeout is largely a safety mechanism against misbehaving applications. It should be set large enough to cover the processing of an entire application batch, i.e., the factor between gro_flush_timeout and irq_suspend_timeout should roughly correspond to the maximum batch size that the target application would process in one go. ~ Important call out in the implementation - Enabling per epoll-context preferred busy poll will now effectively lead to a nonblocking iteration through napi_busy_loop, even when busy_poll_usecs is 0. See patch 4. ~ Benchmark configs & descriptions The changes were benchmarked with memcached [3] using the benchmarking tool mutilate [4]. To facilitate benchmarking, a small patch [5] was applied to memcached 1.6.29 to allow setting per-epoll context preferred busy poll and other settings via environment variables. Another small patch [6] was applied to libevent to enable full busy-polling. Multiple scenarios were benchmarked as described below and the scripts used for producing these results can be found on github [7] (note: all scenarios use NAPI-based traffic splitting via SO_INCOMING_ID by passing -N to memcached): - base: - no other options enabled - deferX: - set defer_hard_irqs to 100 - set gro_flush_timeout to X,000 - napibusy: - set defer_hard_irqs to 100 - set gro_flush_timeout to 200,000 - enable busy poll via the existing ioctl (busy_poll_usecs = 64, busy_poll_budget = 64, prefer_busy_poll = true) - fullbusy: - set defer_hard_irqs to 100 - set gro_flush_timeout to 5,000,000 - enable busy poll via the existing ioctl (busy_poll_usecs = 1000, busy_poll_budget = 64, prefer_busy_poll = true) - change memcached's nonblocking epoll_wait invocation (via libevent) to using a 1 ms timeout - suspend0: - set defer_hard_irqs to 0 - set gro_flush_timeout to 0 - set irq_suspend_timeout to 20,000,000 - enable busy poll via the existing ioctl (busy_poll_usecs = 0, busy_poll_budget = 64, prefer_busy_poll = true) - suspendX: - set defer_hard_irqs to 100 - set gro_flush_timeout to X,000 - set irq_suspend_timeout to 20,000,000 - enable busy poll via the existing ioctl (busy_poll_usecs = 0, busy_poll_budget = 64, prefer_busy_poll = true) ~ Benchmark results Tested on: Single socket AMD EPYC 7662 64-Core Processor Hyperthreading disabled 4 NUMA Zones (NPS=4) 16 CPUs per NUMA zone (64 cores total) 2 x Dual port 100gbps Mellanox Technologies ConnectX-5 Ex EN NIC The test machine is configured such that a single interface has 8 RX queues. The queues' IRQs and memcached are pinned to CPUs that are NUMA-local to the interface which is under test. The NIC's interrupt coalescing configuration is left at boot-time defaults. Results: Results are shown below. The mechanism added by this series is represented by the 'suspend' cases. Data presented shows a summary over nearly 10 runs of each test case [8] using the scripts on github [7]. For latency, the median is shown. For throughput and CPU utilization, the average is shown. The results also include cycles-per-query (cpq) and instruction-per-query (ipq) metrics, following the methodology proposed in [2], to augment the CPU utilization numbers, which could be skewed due to frequency scaling. We find that this does not appear to be the case as CPU utilization and low-level metrics show similar trends. These results were captured using the scripts on github [7] to illustrate how this approach compares with other pre-existing mechanisms. This data is not to be interpreted as scientific data captured in a fully isolated lab setting, but instead as best effort, illustrative information comparing and contrasting tradeoffs. The absolute QPS results shift between submissions, but the relative differences are equivalent. As patches are rebased, several factors likely influence overall performance. Compare: - Throughput (MAX) and latencies of base vs suspend. - CPU usage of napibusy and fullbusy during lower load (200K, 400K for example) vs suspend. - Latency of the defer variants vs suspend as timeout and load increases. - suspend0, which sets defer_hard_irqs and gro_flush_timeout to 0, has nearly the same performance as the base case (this is FAQ item #1). The overall takeaway is that the suspend variants provide a superior combination of high throughput, low latency, and low cpu utilization compared to all other variants. Each of the suspend variants works very well, but some fine-tuning between latency and cpu utilization is still possible by tuning the small timeout (gro_flush_timeout). Note: we've reorganized the results to make comparison among testcases with the same load easier. testcase load qps avglat 95%lat 99%lat cpu cpq ipq base 200K 199946 112 239 416 26 12973 11343 defer10 200K 199971 54 124 142 29 19412 17460 defer20 200K 199986 60 130 153 26 15644 14095 defer50 200K 200025 79 144 182 23 12122 11632 defer200 200K 199999 164 254 309 19 8923 9635 fullbusy 200K 199998 46 118 133 100 43658 23133 napibusy 200K 199983 100 237 277 56 24840 24716 suspend0 200K 200020 105 249 432 30 14264 11796 suspend10 200K 199950 53 123 141 32 19518 16903 suspend20 200K 200037 58 126 151 30 16426 14736 suspend50 200K 199961 73 136 177 26 13310 12633 suspend200 200K 199998 149 251 306 21 9566 10203 testcase load qps avglat 95%lat 99%lat cpu cpq ipq base 400K 400014 139 269 707 41 9476 9343 defer10 400K 400016 59 133 166 53 13991 12989 defer20 400K 399952 67 140 172 47 12063 11644 defer50 400K 400007 87 162 198 39 9384 9880 defer200 400K 399979 181 274 330 31 7089 8430 fullbusy 400K 399987 50 123 156 100 21827 16037 napibusy 400K 400014 76 222 272 83 18185 16529 suspend0 400K 400015 127 350 776 47 10699 9603 suspend10 400K 400023 57 129 164 54 13758 13178 suspend20 400K 400043 62 135 169 49 12071 11826 suspend50 400K 400071 76 149 186 42 10011 10301 suspend200 400K 399961 154 269 327 34 7827 8774 testcase load qps avglat 95%lat 99%lat cpu cpq ipq base 600K 599951 149 266 574 61 9265 8876 defer10 600K 600006 71 147 203 76 11866 10936 defer20 600K 600123 76 152 203 66 10430 10342 defer50 600K 600162 95 172 217 54 8526 9142 defer200 600K 599942 200 301 357 46 6977 8212 fullbusy 600K 599990 55 127 177 100 14551 13983 napibusy 600K 600035 63 160 250 96 13937 14140 suspend0 600K 599903 127 320 732 68 10166 8963 suspend10 600K 599908 63 137 192 69 10902 11100 suspend20 600K 599961 66 141 194 65 9976 10370 suspend50 600K 599973 80 159 204 57 8678 9381 suspend200 600K 600010 157 277 346 48 7133 8381 testcase load qps avglat 95%lat 99%lat cpu cpq ipq base 800K 800039 181 300 536 87 9585 8304 defer10 800K 800038 181 530 939 96 10564 8970 defer20 800K 800029 112 225 329 90 10056 8935 defer50 800K 799999 120 208 296 82 9234 8562 defer200 800K 800066 227 338 401 63 7117 8129 fullbusy 800K 800040 61 134 190 100 10913 12608 napibusy 800K 799944 64 141 214 99 10828 12588 suspend0 800K 799911 126 248 509 85 9346 8498 suspend10 800K 800006 69 143 200 83 9410 9845 suspend20 800K 800120 74 150 207 78 8786 9454 suspend50 800K 799989 87 168 224 71 7946 8833 suspend200 800K 799987 160 292 357 62 6923 8229 testcase load qps avglat 95%lat 99%lat cpu cpq ipq base 1000K 906879 4079 5751 6216 98 9496 7904 defer10 1000K 860849 3643 6274 6730 99 10040 8676 defer20 1000K 896063 3298 5840 6349 98 9620 8237 defer50 1000K 919782 2962 5513 5807 97 9284 7951 defer200 1000K 970941 3059 5348 5984 95 8593 7959 fullbusy 1000K 999950 70 150 207 100 8732 10777 napibusy 1000K 999996 78 154 223 100 8722 10656 suspend0 1000K 949706 2666 5770 6660 99 9071 8046 suspend10 1000K 1000024 80 160 220 92 8137 9035 suspend20 1000K 1000059 83 165 226 89 7850 8804 suspend50 1000K 999955 95 180 240 84 7411 8459 suspend200 1000K 999914 163 299 366 77 6833 8078 testcase load qps avglat 95%lat 99%lat cpu cpq ipq base MAX 1037654 4184 5453 5810 100 8411 7938 defer10 MAX 905607 4840 6151 6380 100 9639 8431 defer20 MAX 986463 4455 5594 5796 100 8848 8110 defer50 MAX 1077030 4000 5073 5299 100 8104 7920 defer200 MAX 1040728 4152 5385 5765 100 8379 7849 fullbusy MAX 1247536 3518 3935 3984 100 6998 7930 napibusy MAX 1136310 3799 7756 9964 100 7670 7877 suspend0 MAX 1057509 4132 5724 6185 100 8253 7918 suspend10 MAX 1215147 3580 3957 4041 100 7185 7944 suspend20 MAX 1216469 3576 3953 3988 100 7175 7950 suspend50 MAX 1215871 3577 3961 4075 100 7181 7949 suspend200 MAX 1216882 3556 3951 3988 100 7175 7955 ~ FAQ - Why is a new parameter needed? Does irq_suspend_timeout override gro_flush_timeout? Using the suspend mechanism causes the system to alternate between polling mode and irq-driven packet delivery. During busy periods, irq_suspend_timeout overrides gro_flush_timeout and keeps the system busy polling, but when epoll finds no events, the setting of gro_flush_timeout and napi_defer_hard_irqs determine the next step. There are essentially three possible loops for network processing and packet delivery: 1) hardirq -> softirq -> napi poll; basic interrupt delivery 2) timer -> softirq -> napi poll; deferred irq processing 3) epoll -> busy-poll -> napi poll; busy looping Loop 2 can take control from Loop 1, if gro_flush_timeout and napi_defer_hard_irqs are set. If gro_flush_timeout and napi_defer_hard_irqs are set, Loops 2 and 3 "wrestle" with each other for control. During busy periods, irq_suspend_timeout is used as timer in Loop 2, which essentially tilts this in favour of Loop 3. If gro_flush_timeout and napi_defer_hard_irqs are not set, Loop 3 cannot take control from Loop 1. Therefore, setting gro_flush_timeout and napi_defer_hard_irqs is the recommended usage, because otherwise setting irq_suspend_timeout might not have any discernible effect. This is shown in the results above: compare suspend0 with the base case. Note that the lack of napi_defer_hard_irqs and gro_flush_timeout produce similar results for both, which encourages the use of napi_defer_hard_irqs and gro_flush_timeout in addition to irq_suspend_timeout. - Can the new timeout value be threaded through the new epoll ioctl ? It is possible, but presents challenges for userspace. User applications must ensure that the file descriptors added to epoll contexts have the same NAPI ID to support busy polling. An epoll context is not permanently tied to any particular NAPI ID. So, a user application could decide to clear the file descriptors from the context and add a new set of file descriptors with a different NAPI ID to the context. Busy polling would work as expected, but the meaning of the suspend timeout becomes ambiguous because IRQs are not inherently associated with epoll contexts, but rather with the NAPI. The user program would need to reissue the ioctl to set the irq_suspend_timeout, but the napi_defer_hard_irqs and gro_flush_timeout settings would come from the NAPI's napi_config (which are set either by sysfs or by netlink). Such an interface seems awkard to use from a user perspective. Further, IRQs are related to NAPIs, which is why they are stored in the napi_config space. Putting the irq_suspend_timeout in the epoll context while other IRQ deferral mechanisms remain in the NAPI's napi_config space seems like an odd design choice. We've opted to keep all of the IRQ deferral parameters together and place the irq_suspend_timeout in napi_config. This has nice benefits for userspace: if a user app were to remove all file descriptors from an epoll context and add new file descriptors with a new NAPI ID, the correct suspend timeout for that NAPI ID would be used automatically without the user application needing to do anything (like re-issuing an ioctl, for example). All IRQ deferral related parameters are in one place and can all be set the same way: with netlink. - Can irq suspend be built by combining NIC coalescing and gro_flush_timeout ? No. The problem is that the long timeout must engage if and only if prefer-busy is active. When using NIC coalescing for the short timeout (without napi_defer_hard_irqs/gro_flush_timeout), an interrupt after an idle period will trigger softirq, which will run napi polling. At this point, prefer-busy is not active, so NIC interrupts would be re-enabled. Then it is not possible for the longer timeout to interject to switch control back to polling. In other words, only by using the software timer for the short timeout, it is possible to extend the timeout without having to reprogram the NIC timer or reach down directly and disable interrupts. Using gro_flush_timeout for the long timeout also has problems, for the same underlying reason. In the current napi implementation, gro_flush_timeout is not tied to prefer-busy. We'd either have to change that and in the process modify the existing deferral mechanism, or introduce a state variable to determine whether gro_flush_timeout is used as long timeout for irq suspend or whether it is used for its default purpose. In an earlier version, we did try something similar to the latter and made it work, but it ends up being a lot more convoluted than our current proposal. - Isn't it already possible to combine busy looping with irq deferral? Yes, in fact enabling irq deferral via napi_defer_hard_irqs and gro_flush_timeout is a precondition for prefer_busy_poll to have an effect. If the application also uses a tight busy loop with essentially nonblocking epoll_wait (accomplished with a very short timeout parameter), this is the fullbusy case shown in the results. An application using blocking epoll_wait is shown as the napibusy case in the results. It's a hybrid approach that provides limited latency benefits compared to the base case and plain irq deferral, but not as good as fullbusy or suspend. ~ Special thanks Several people were involved in earlier stages of the development of this mechanism whom we'd like to thank: - Peter Cai (CC'd), for the initial kernel patch and his contributions to the paper. - Mohammadamin Shafie (CC'd), for testing various versions of the kernel patch and providing helpful feedback. Thanks, Martin and Joe [1]: https://lore.kernel.org/netdev/20240812125717.413108-1-jdamato@fastly.com/ [2]: https://doi.org/10.1145/3626780 [3]: https://github.com/memcached/memcached/blob/master/doc/napi_ids.txt [4]: https://github.com/leverich/mutilate [5]: https://raw.githubusercontent.com/martinkarsten/irqsuspend/main/patches/mem… [6]: https://raw.githubusercontent.com/martinkarsten/irqsuspend/main/patches/lib… [7]: https://github.com/martinkarsten/irqsuspend [8]: https://github.com/martinkarsten/irqsuspend/tree/main/results v9: - Addresses Willem's feedback on the selftests in patch 5 by fixing the SPDX-License-Identifier, moving constants into variables in the test script, reducing code duplication, shortening long lines, and renaming variables to be more reader friendly. In the C test file, added a comment explaining the if def blob and changed a few types for strtoul. v8: https://lore.kernel.org/netdev/20241108045337.292905-1-jdamato@fastly.com/ - Update patch 2 to drop the exports, as requested by Jakub. v7: https://lore.kernel.org/netdev/20241108023912.98416-1-jdamato@fastly.com/ - Jakub noted that patch 2 adds unnecessary complexity by checking the suspend timeout in the NAPI loop. This makes the code more complicated and difficult to reason about. He's right; we've dropped patch 2 which simplifies this series. - Updated the cover letter with a full re-run of all test cases. - Updated FAQ #2. v6: https://lore.kernel.org/netdev/20241104215542.215919-1-jdamato@fastly.com/ - Updated the cover letter with a full re-run of all test cases, including a new case suspend0, as requested by Sridhar previously. - Updated the kernel documentation in patch 7 as suggested by Bagas Sanjaya, which improved the htmldoc output. v5: https://lore.kernel.org/netdev/20241103052421.518856-1-jdamato@fastly.com/ - Adjusted patch 5 to only suspend IRQs when ep_send_events returns a positive return value. This issue was pointed out by Hillf Danton. - Updated the commit message of patch 6 which still mentioned netcat, despite the code being updated in v4 to replace it with socat and fixed misspelling of netdevsim. - Fixed a minor typo in patch 7 and removed an unnecessary paragraph. - Added Sridhar Samudrala's Reviewed-by to patch 1-5 and 7. v4: https://lore.kernel.org/netdev/20241102005214.32443-1-jdamato@fastly.com/ - Added a new FAQ item to cover letter. - Updated patch 6 to use socat instead of nc in busy_poll_test.sh and updated busy_poller.c to use netlink directly to configure napi params. - Updated the kernel documentation in patch 7 to include more details. - Dropped Stanislav's Acked-by and Bagas' Reviewed-by from patch 7 since the documentation was updated. v3: https://lore.kernel.org/netdev/20241101004846.32532-1-jdamato@fastly.com/ - Added Stanislav Fomichev's Acked-by to every patch except the newly added selftest. - Added Bagas Sanjaya's Reviewed-by to the documentation patch. - Fixed the commit message of patch 2 to remove a reference to the now non-existent sysfs setting. - Added a self test which tests both "regular" busy poll and busy poll with suspend enabled. This was added as patch 6 as requested by Paolo. netdevsim was chosen instead of veth due to netdevsim's pre-existing support for netdev-genl. See the commit message of patch 6 for more details. v2: https://lore.kernel.org/bpf/20241021015311.95468-1-jdamato@fastly.com/ - Cover letter updated, including a re-run of test data. - Patch 1 rewritten to use netdev-genl instead of sysfs. - Patch 3 updated with a comment added to napi_resume_irqs. - Patch 4 rebased to apply now that commit b9ca079dd6b0 ("eventpoll: Annotate data-race of busy_poll_usecs") has been picked up from VFS. - Patch 6 updated the kernel documentation. rfc -> v1: - Cover letter updated to include more details. - Patch 1 updated to remove the documentation added. This was moved to patch 6 with the rest of the docs (see below). - Patch 5 updated to fix an error uncovered by the kernel build robot. See patch 5's changelog for more details. - Patch 6 added which updates kernel documentation. Joe Damato (2): selftests: net: Add busy_poll_test docs: networking: Describe irq suspension Martin Karsten (4): net: Add napi_struct parameter irq_suspend_timeout net: Add control functions for irq suspension eventpoll: Trigger napi_busy_loop, if prefer_busy_poll is set eventpoll: Control irq suspension for prefer_busy_poll Documentation/netlink/specs/netdev.yaml | 7 + Documentation/networking/napi.rst | 170 ++++++++- fs/eventpoll.c | 36 +- include/linux/netdevice.h | 2 + include/net/busy_poll.h | 3 + include/uapi/linux/netdev.h | 1 + net/core/dev.c | 39 ++ net/core/dev.h | 25 ++ net/core/netdev-genl-gen.c | 5 +- net/core/netdev-genl.c | 12 + tools/include/uapi/linux/netdev.h | 1 + tools/testing/selftests/net/.gitignore | 1 + tools/testing/selftests/net/Makefile | 3 +- tools/testing/selftests/net/busy_poll_test.sh | 165 +++++++++ tools/testing/selftests/net/busy_poller.c | 346 ++++++++++++++++++ 15 files changed, 809 insertions(+), 7 deletions(-) create mode 100755 tools/testing/selftests/net/busy_poll_test.sh create mode 100644 tools/testing/selftests/net/busy_poller.c base-commit: dc7c381bb8649e3701ed64f6c3e55316675904d7 -- 2.25.1

11 months, 4 weeks

3
3
0 0

[PATCH net-next v8 00/12] selftests: ncdevmem: Add ncdevmem to ksft

by Stanislav Fomichev

The goal of the series is to simplify and make it possible to use ncdevmem in an automated way from the ksft python wrapper. ncdevmem is slowly mutated into a state where it uses stdout to print the payload and the python wrapper is added to make sure the arrived payload matches the expected one. v8: - move error() calls into enable_reuseaddr() (Joe) - bail out when number of queues is 1 (Joe) - use socat instead of nc (Joe) - fix warning about string truncation buf[256]->buf[40] (Jakub) v7: - fix validation (Mina) - add support for working with non ::ffff-prefixed addresses (Mina) v6: - fix compilation issue in 'Unify error handling' patch (Jakub) v5: - properly handle errors from inet_pton() and socket() (Paolo) - remove unneeded import from python selftest (Paolo) v4: - keep usage example with validation (Mina) - fix compilation issue in one patch (s/start_queues/start_queue/) v3: - keep and refine the comment about ncdevmem invocation (Mina) - add the comment about not enforcing exit status for ntuple reset (Mina) - make configure_headersplit more robust (Mina) - use num_queues/2 in selftest and let the users override it (Mina) - remove memory_provider.memcpy_to_device (Mina) - keep ksft as is (don't use -v validate flags): we are gonna need a --debug-disable flag to make it less chatty; otherwise it times out when sending too much data; so leaving it as a separate follow up v2: - don't remove validation (Mina) - keep 5-tuple flow steering but use it only when -c is provided (Mina) - remove separate flag for probing (Mina) - move ncdevmem under drivers/net/hw, not drivers/net (Jakub) Cc: Mina Almasry <almasrymina(a)google.com> Stanislav Fomichev (12): selftests: ncdevmem: Redirect all non-payload output to stderr selftests: ncdevmem: Separate out dmabuf provider selftests: ncdevmem: Unify error handling selftests: ncdevmem: Make client_ip optional selftests: ncdevmem: Remove default arguments selftests: ncdevmem: Switch to AF_INET6 selftests: ncdevmem: Properly reset flow steering selftests: ncdevmem: Use YNL to enable TCP header split selftests: ncdevmem: Remove hard-coded queue numbers selftests: ncdevmem: Run selftest when none of the -s or -c has been provided selftests: ncdevmem: Move ncdevmem under drivers/net/hw selftests: ncdevmem: Add automated test .../selftests/drivers/net/hw/.gitignore | 1 + .../testing/selftests/drivers/net/hw/Makefile | 9 + .../selftests/drivers/net/hw/devmem.py | 45 + .../selftests/drivers/net/hw/ncdevmem.c | 789 ++++++++++++++++++ tools/testing/selftests/net/.gitignore | 1 - tools/testing/selftests/net/Makefile | 8 - tools/testing/selftests/net/ncdevmem.c | 570 ------------- 7 files changed, 844 insertions(+), 579 deletions(-) create mode 100644 tools/testing/selftests/drivers/net/hw/.gitignore create mode 100755 tools/testing/selftests/drivers/net/hw/devmem.py create mode 100644 tools/testing/selftests/drivers/net/hw/ncdevmem.c delete mode 100644 tools/testing/selftests/net/ncdevmem.c -- 2.47.0

11 months, 4 weeks

4
16
0 0

[PATCH net-next v3 0/4] Introduce VLAN support in HSR

by MD Danish Anwar

This series adds VLAN support to HSR framework. This series also adds VLAN support to HSR mode of ICSSG Ethernet driver. Changes from v2 to v3: *) Modified hsr_ndo_vlan_rx_add_vid() to handle arbitrary HSR_PT_SLAVE_A, HSR_PT_SLAVE_B order and skip INTERLINK port in patch 2/4 as suggested by Paolo Abeni <pabeni(a)redhat.com> *) Removed handling of HSR_PT_MASTER in hsr_ndo_vlan_rx_kill_vid() as MASTER and INTERLINK port will be ignored anyway in the default switch case as suggested by Paolo Abeni <pabeni(a)redhat.com> *) Modified the selftest in patch 4/4 to use vlan by default. The test will check the exposed feature `vlan-challenged` and if vlan is not supported, skip the vlan test as suggested by Paolo Abeni <pabeni(a)redhat.com>. Test logs can be found at [1] Changes from v1 to v2: *) Added patch 4/4 to add test script related to VLAN in HSR as asked by Lukasz Majewski <lukma(a)denx.de> [1] https://gist.githubusercontent.com/danish-ti/d309f92c640134ccc4f2c0c442de5b… v1 https://lore.kernel.org/all/20241004074715.791191-1-danishanwar@ti.com/ v2 https://lore.kernel.org/all/20241024103056.3201071-1-danishanwar@ti.com/ MD Danish Anwar (1): selftests: hsr: Add test for VLAN Murali Karicheri (1): net: hsr: Add VLAN CTAG filter support Ravi Gunasekaran (1): net: ti: icssg-prueth: Add VLAN support for HSR mode WingMan Kwok (1): net: hsr: Add VLAN support drivers/net/ethernet/ti/icssg/icssg_prueth.c | 45 ++++++++- net/hsr/hsr_device.c | 85 +++++++++++++++-- net/hsr/hsr_forward.c | 19 +++- tools/testing/selftests/net/hsr/config | 1 + tools/testing/selftests/net/hsr/hsr_ping.sh | 98 ++++++++++++++++++++ 5 files changed, 236 insertions(+), 12 deletions(-) base-commit: a84e8c05f58305dfa808bc5465c5175c29d7c9b6 -- 2.34.1

11 months, 4 weeks

3
6
0 0

[PATCH net-next v7] ipv6: Fix soft lockups in fib6_select_path under high next hop churn

by Omid Ehtemam-Haghighi

Soft lockups have been observed on a cluster of Linux-based edge routers located in a highly dynamic environment. Using the `bird` service, these routers continuously update BGP-advertised routes due to frequently changing nexthop destinations, while also managing significant IPv6 traffic. The lockups occur during the traversal of the multipath circular linked-list in the `fib6_select_path` function, particularly while iterating through the siblings in the list. The issue typically arises when the nodes of the linked list are unexpectedly deleted concurrently on a different core—indicated by their 'next' and 'previous' elements pointing back to the node itself and their reference count dropping to zero. This results in an infinite loop, leading to a soft lockup that triggers a system panic via the watchdog timer. Apply RCU primitives in the problematic code sections to resolve the issue. Where necessary, update the references to fib6_siblings to annotate or use the RCU APIs. Include a test script that reproduces the issue. The script periodically updates the routing table while generating a heavy load of outgoing IPv6 traffic through multiple iperf3 clients. It consistently induces infinite soft lockups within a couple of minutes. Kernel log: 0 [ffffbd13003e8d30] machine_kexec at ffffffff8ceaf3eb 1 [ffffbd13003e8d90] __crash_kexec at ffffffff8d0120e3 2 [ffffbd13003e8e58] panic at ffffffff8cef65d4 3 [ffffbd13003e8ed8] watchdog_timer_fn at ffffffff8d05cb03 4 [ffffbd13003e8f08] __hrtimer_run_queues at ffffffff8cfec62f 5 [ffffbd13003e8f70] hrtimer_interrupt at ffffffff8cfed756 6 [ffffbd13003e8fd0] __sysvec_apic_timer_interrupt at ffffffff8cea01af 7 [ffffbd13003e8ff0] sysvec_apic_timer_interrupt at ffffffff8df1b83d -- <IRQ stack> -- 8 [ffffbd13003d3708] asm_sysvec_apic_timer_interrupt at ffffffff8e000ecb [exception RIP: fib6_select_path+299] RIP: ffffffff8ddafe7b RSP: ffffbd13003d37b8 RFLAGS: 00000287 RAX: ffff975850b43600 RBX: ffff975850b40200 RCX: 0000000000000000 RDX: 000000003fffffff RSI: 0000000051d383e4 RDI: ffff975850b43618 RBP: ffffbd13003d3800 R8: 0000000000000000 R9: ffff975850b40200 R10: 0000000000000000 R11: 0000000000000000 R12: ffffbd13003d3830 R13: ffff975850b436a8 R14: ffff975850b43600 R15: 0000000000000007 ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018 9 [ffffbd13003d3808] ip6_pol_route at ffffffff8ddb030c 10 [ffffbd13003d3888] ip6_pol_route_input at ffffffff8ddb068c 11 [ffffbd13003d3898] fib6_rule_lookup at ffffffff8ddf02b5 12 [ffffbd13003d3928] ip6_route_input at ffffffff8ddb0f47 13 [ffffbd13003d3a18] ip6_rcv_finish_core.constprop.0 at ffffffff8dd950d0 14 [ffffbd13003d3a30] ip6_list_rcv_finish.constprop.0 at ffffffff8dd96274 15 [ffffbd13003d3a98] ip6_sublist_rcv at ffffffff8dd96474 16 [ffffbd13003d3af8] ipv6_list_rcv at ffffffff8dd96615 17 [ffffbd13003d3b60] __netif_receive_skb_list_core at ffffffff8dc16fec 18 [ffffbd13003d3be0] netif_receive_skb_list_internal at ffffffff8dc176b3 19 [ffffbd13003d3c50] napi_gro_receive at ffffffff8dc565b9 20 [ffffbd13003d3c80] ice_receive_skb at ffffffffc087e4f5 [ice] 21 [ffffbd13003d3c90] ice_clean_rx_irq at ffffffffc0881b80 [ice] 22 [ffffbd13003d3d20] ice_napi_poll at ffffffffc088232f [ice] 23 [ffffbd13003d3d80] __napi_poll at ffffffff8dc18000 24 [ffffbd13003d3db8] net_rx_action at ffffffff8dc18581 25 [ffffbd13003d3e40] __do_softirq at ffffffff8df352e9 26 [ffffbd13003d3eb0] run_ksoftirqd at ffffffff8ceffe47 27 [ffffbd13003d3ec0] smpboot_thread_fn at ffffffff8cf36a30 28 [ffffbd13003d3ee8] kthread at ffffffff8cf2b39f 29 [ffffbd13003d3f28] ret_from_fork at ffffffff8ce5fa64 30 [ffffbd13003d3f50] ret_from_fork_asm at ffffffff8ce03cbb Fixes: 66f5d6ce53e6 ("ipv6: replace rwlock with rcu and spinlock in fib6_table") Reported-by: Adrian Oliver <kernel(a)aoliver.ca> Signed-off-by: Omid Ehtemam-Haghighi <omid.ehtemamhaghighi(a)menlosecurity.com> Cc: David S. Miller <davem(a)davemloft.net> Cc: David Ahern <dsahern(a)gmail.com> Cc: Eric Dumazet <edumazet(a)google.com> Cc: Jakub Kicinski <kuba(a)kernel.org> Cc: Paolo Abeni <pabeni(a)redhat.com> Cc: Shuah Khan <shuah(a)kernel.org> Cc: Ido Schimmel <idosch(a)idosch.org> Cc: Kuniyuki Iwashima <kuniyu(a)amazon.com> Cc: Simon Horman <horms(a)kernel.org> Cc: Omid Ehtemam-Haghighi <oeh.kernel(a)gmail.com> Cc: netdev(a)vger.kernel.org Cc: linux-kselftest(a)vger.kernel.org Cc: linux-kernel(a)vger.kernel.org --- v6 -> v7: * Rebased on top of 'net-next' v5 -> v6: * Adjust the comment line lengths in the test script to a maximum of 80 characters * Change memory allocation in inet6_rt_notify from gfp_any() to GFP_ATOMIC for atomic allocation in non-blocking contexts, as suggested by Ido Schimmel * NOTE: I have executed the test script on both bare-metal servers and virtualized environments such as QEMU and vng. In the case of bare-metal, it consistently triggers a soft lockup in under a minute on unpatched kernels. For the virtualized environments, an unpatched kernel compiled with the Ubuntu 24.04 configuration also triggers a soft lockup, though it takes longer; however, it did not trigger a soft lockup on kernels compiled with configurations provided in: https://github.com/linux-netdev/nipa/wiki/How-to-run-netdev-selftests-CI-st… leading to potential false negatives in the test results. I am curious if this test can be executed on a bare-metal machine within a CI system, if such a setup exists, rather than in a virtualized environment. If that’s not possible, how can I apply a different kernel configuration, such as the one used in Ubuntu 24.04, for this test? Please advise. v4 -> v5: * Addressed review comments from Paolo Abeni. * Added additional clarifying comments in the test script. * Minor cleanup performed in the test script. v3 -> v4: * Added RCU primitives to rt6_fill_node(). I found that this function is typically called either with a table lock held or within rcu_read_lock/rcu_read_unlock pairs, except in the following call chain, where the protection is unclear: rt_fill_node() fib6_info_hw_flags_set() mlxsw_sp_fib6_offload_failed_flag_set() mlxsw_sp_router_fib6_event_work() The last function is initialized as a work item in mlxsw_sp_router_fib_event() and scheduled for deferred execution. I am unsure if the execution context of this work item is protected by any table lock or rcu_read_lock/rcu_read_unlock pair, so I have added the protection. Please let me know if this is redundant. * Other review comments addressed v2 -> v3: * Removed redundant rcu_read_lock()/rcu_read_unlock() pairs * Revised the test script based on Ido Schimmel's feedback * Updated the test script to ensure compatibility with the latest iperf3 version * Fixed new warnings generated with 'C=2' in the previous version * Other review comments addressed v1 -> v2: * list_del_rcu() is applied exclusively to legacy multipath code * All occurrences of fib6_siblings have been modified to utilize RCU APIs for annotation and usage. * Additionally, a test script for reproducing the reported issue is included --- net/ipv6/ip6_fib.c | 8 +- net/ipv6/route.c | 45 ++- tools/testing/selftests/net/Makefile | 1 + .../net/ipv6_route_update_soft_lockup.sh | 262 ++++++++++++++++++ 4 files changed, 297 insertions(+), 19 deletions(-) create mode 100755 tools/testing/selftests/net/ipv6_route_update_soft_lockup.sh diff --git a/net/ipv6/ip6_fib.c b/net/ipv6/ip6_fib.c index 6383263bfd04..c134ba202c4c 100644 --- a/net/ipv6/ip6_fib.c +++ b/net/ipv6/ip6_fib.c @@ -1183,8 +1183,8 @@ static int fib6_add_rt2node(struct fib6_node *fn, struct fib6_info *rt, while (sibling) { if (sibling->fib6_metric == rt->fib6_metric && rt6_qualify_for_ecmp(sibling)) { - list_add_tail(&rt->fib6_siblings, - &sibling->fib6_siblings); + list_add_tail_rcu(&rt->fib6_siblings, + &sibling->fib6_siblings); break; } sibling = rcu_dereference_protected(sibling->fib6_next, @@ -1245,7 +1245,7 @@ static int fib6_add_rt2node(struct fib6_node *fn, struct fib6_info *rt, fib6_siblings) sibling->fib6_nsiblings--; rt->fib6_nsiblings = 0; - list_del_init(&rt->fib6_siblings); + list_del_rcu(&rt->fib6_siblings); rt6_multipath_rebalance(next_sibling); return err; } @@ -1963,7 +1963,7 @@ static void fib6_del_route(struct fib6_table *table, struct fib6_node *fn, &rt->fib6_siblings, fib6_siblings) sibling->fib6_nsiblings--; rt->fib6_nsiblings = 0; - list_del_init(&rt->fib6_siblings); + list_del_rcu(&rt->fib6_siblings); rt6_multipath_rebalance(next_sibling); } diff --git a/net/ipv6/route.c b/net/ipv6/route.c index d7ce5cf2017a..e23e653de158 100644 --- a/net/ipv6/route.c +++ b/net/ipv6/route.c @@ -413,8 +413,8 @@ void fib6_select_path(const struct net *net, struct fib6_result *res, struct flowi6 *fl6, int oif, bool have_oif_match, const struct sk_buff *skb, int strict) { - struct fib6_info *sibling, *next_sibling; struct fib6_info *match = res->f6i; + struct fib6_info *sibling; if (!match->nh && (!match->fib6_nsiblings || have_oif_match)) goto out; @@ -440,8 +440,8 @@ void fib6_select_path(const struct net *net, struct fib6_result *res, if (fl6->mp_hash <= atomic_read(&match->fib6_nh->fib_nh_upper_bound)) goto out; - list_for_each_entry_safe(sibling, next_sibling, &match->fib6_siblings, - fib6_siblings) { + list_for_each_entry_rcu(sibling, &match->fib6_siblings, + fib6_siblings) { const struct fib6_nh *nh = sibling->fib6_nh; int nh_upper_bound; @@ -5195,14 +5195,18 @@ static void ip6_route_mpath_notify(struct fib6_info *rt, * nexthop. Since sibling routes are always added at the end of * the list, find the first sibling of the last route appended */ + rcu_read_lock(); + if ((nlflags & NLM_F_APPEND) && rt_last && rt_last->fib6_nsiblings) { - rt = list_first_entry(&rt_last->fib6_siblings, - struct fib6_info, - fib6_siblings); + rt = list_first_or_null_rcu(&rt_last->fib6_siblings, + struct fib6_info, + fib6_siblings); } if (rt) inet6_rt_notify(RTM_NEWROUTE, rt, info, nlflags); + + rcu_read_unlock(); } static bool ip6_route_mpath_should_notify(const struct fib6_info *rt) @@ -5547,17 +5551,21 @@ static size_t rt6_nlmsg_size(struct fib6_info *f6i) nexthop_for_each_fib6_nh(f6i->nh, rt6_nh_nlmsg_size, &nexthop_len); } else { - struct fib6_info *sibling, *next_sibling; struct fib6_nh *nh = f6i->fib6_nh; + struct fib6_info *sibling; nexthop_len = 0; if (f6i->fib6_nsiblings) { rt6_nh_nlmsg_size(nh, &nexthop_len); - list_for_each_entry_safe(sibling, next_sibling, - &f6i->fib6_siblings, fib6_siblings) { + rcu_read_lock(); + + list_for_each_entry_rcu(sibling, &f6i->fib6_siblings, + fib6_siblings) { rt6_nh_nlmsg_size(sibling->fib6_nh, &nexthop_len); } + + rcu_read_unlock(); } nexthop_len += lwtunnel_get_encap_size(nh->fib_nh_lws); } @@ -5721,7 +5729,7 @@ static int rt6_fill_node(struct net *net, struct sk_buff *skb, lwtunnel_fill_encap(skb, dst->lwtstate, RTA_ENCAP, RTA_ENCAP_TYPE) < 0) goto nla_put_failure; } else if (rt->fib6_nsiblings) { - struct fib6_info *sibling, *next_sibling; + struct fib6_info *sibling; struct nlattr *mp; mp = nla_nest_start_noflag(skb, RTA_MULTIPATH); @@ -5733,14 +5741,21 @@ static int rt6_fill_node(struct net *net, struct sk_buff *skb, 0) < 0) goto nla_put_failure; - list_for_each_entry_safe(sibling, next_sibling, - &rt->fib6_siblings, fib6_siblings) { + rcu_read_lock(); + + list_for_each_entry_rcu(sibling, &rt->fib6_siblings, + fib6_siblings) { if (fib_add_nexthop(skb, &sibling->fib6_nh->nh_common, sibling->fib6_nh->fib_nh_weight, - AF_INET6, 0) < 0) + AF_INET6, 0) < 0) { + rcu_read_unlock(); + goto nla_put_failure; + } } + rcu_read_unlock(); + nla_nest_end(skb, mp); } else if (rt->nh) { if (nla_put_u32(skb, RTA_NH_ID, rt->nh->id)) @@ -6177,7 +6192,7 @@ void inet6_rt_notify(int event, struct fib6_info *rt, struct nl_info *info, err = -ENOBUFS; seq = info->nlh ? info->nlh->nlmsg_seq : 0; - skb = nlmsg_new(rt6_nlmsg_size(rt), gfp_any()); + skb = nlmsg_new(rt6_nlmsg_size(rt), GFP_ATOMIC); if (!skb) goto errout; @@ -6190,7 +6205,7 @@ void inet6_rt_notify(int event, struct fib6_info *rt, struct nl_info *info, goto errout; } rtnl_notify(skb, net, info->portid, RTNLGRP_IPV6_ROUTE, - info->nlh, gfp_any()); + info->nlh, GFP_ATOMIC); return; errout: rtnl_set_sk_err(net, RTNLGRP_IPV6_ROUTE, err); diff --git a/tools/testing/selftests/net/Makefile b/tools/testing/selftests/net/Makefile index 26a4883a65c9..8c4db5199a42 100644 --- a/tools/testing/selftests/net/Makefile +++ b/tools/testing/selftests/net/Makefile @@ -96,6 +96,7 @@ TEST_PROGS += fdb_flush.sh TEST_PROGS += fq_band_pktlimit.sh TEST_PROGS += vlan_hw_filter.sh TEST_PROGS += bpf_offload.py +TEST_PROGS += ipv6_route_update_soft_lockup.sh # YNL files, must be before "include ..lib.mk" YNL_GEN_FILES := ncdevmem diff --git a/tools/testing/selftests/net/ipv6_route_update_soft_lockup.sh b/tools/testing/selftests/net/ipv6_route_update_soft_lockup.sh new file mode 100755 index 000000000000..a6b2b1f9c641 --- /dev/null +++ b/tools/testing/selftests/net/ipv6_route_update_soft_lockup.sh @@ -0,0 +1,262 @@ +#!/bin/bash +# SPDX-License-Identifier: GPL-2.0 +# +# Testing for potential kernel soft lockup during IPv6 routing table +# refresh under heavy outgoing IPv6 traffic. If a kernel soft lockup +# occurs, a kernel panic will be triggered to prevent associated issues. +# +# +# Test Environment Layout +# +# ┌----------------┐ ┌----------------┐ +# | SOURCE_NS | | SINK_NS | +# | NAMESPACE | | NAMESPACE | +# |(iperf3 clients)| |(iperf3 servers)| +# | | | | +# | | | | +# | ┌-----------| nexthops |---------┐ | +# | |veth_source|<--------------------------------------->|veth_sink|<┐ | +# | └-----------|2001:0DB8:1::0:1/96 2001:0DB8:1::1:1/96 |---------┘ | | +# | | ^ 2001:0DB8:1::1:2/96 | | | +# | | . . | fwd | | +# | ┌---------┐ | . . | | | +# | | IPv6 | | . . | V | +# | | routing | | . 2001:0DB8:1::1:80/96| ┌-----┐ | +# | | table | | . | | lo | | +# | | nexthop | | . └--------┴-----┴-┘ +# | | update | | ............................> 2001:0DB8:2::1:1/128 +# | └-------- ┘ | +# └----------------┘ +# +# The test script sets up two network namespaces, source_ns and sink_ns, +# connected via a veth link. Within source_ns, it continuously updates the +# IPv6 routing table by flushing and inserting IPV6_NEXTHOP_ADDR_COUNT nexthop +# IPs destined for SINK_LOOPBACK_IP_ADDR in sink_ns. This refresh occurs at a +# rate of 1/ROUTING_TABLE_REFRESH_PERIOD per second for TEST_DURATION seconds. +# +# Simultaneously, multiple iperf3 clients within source_ns generate heavy +# outgoing IPv6 traffic. Each client is assigned a unique port number starting +# at 5000 and incrementing sequentially. Each client targets a unique iperf3 +# server running in sink_ns, connected to the SINK_LOOPBACK_IFACE interface +# using the same port number. +# +# The number of iperf3 servers and clients is set to half of the total +# available cores on each machine. +# +# NOTE: We have tested this script on machines with various CPU specifications, +# ranging from lower to higher performance as listed below. The test script +# effectively triggered a kernel soft lockup on machines running an unpatched +# kernel in under a minute: +# +# - 1x Intel Xeon E-2278G 8-Core Processor @ 3.40GHz +# - 1x Intel Xeon E-2378G Processor 8-Core @ 2.80GHz +# - 1x AMD EPYC 7401P 24-Core Processor @ 2.00GHz +# - 1x AMD EPYC 7402P 24-Core Processor @ 2.80GHz +# - 2x Intel Xeon Gold 5120 14-Core Processor @ 2.20GHz +# - 1x Ampere Altra Q80-30 80-Core Processor @ 3.00GHz +# - 2x Intel Xeon Gold 5120 14-Core Processor @ 2.20GHz +# - 2x Intel Xeon Silver 4214 24-Core Processor @ 2.20GHz +# - 1x AMD EPYC 7502P 32-Core @ 2.50GHz +# - 1x Intel Xeon Gold 6314U 32-Core Processor @ 2.30GHz +# - 2x Intel Xeon Gold 6338 32-Core Processor @ 2.00GHz +# +# On less performant machines, you may need to increase the TEST_DURATION +# parameter to enhance the likelihood of encountering a race condition leading +# to a kernel soft lockup and avoid a false negative result. +# +# NOTE: The test may not produce the expected result in virtualized +# environments (e.g., qemu) due to differences in timing and CPU handling, +# which can affect the conditions needed to trigger a soft lockup. + +source lib.sh +source net_helper.sh + +TEST_DURATION=300 +ROUTING_TABLE_REFRESH_PERIOD=0.01 + +IPERF3_BITRATE="300m" + + +IPV6_NEXTHOP_ADDR_COUNT="128" +IPV6_NEXTHOP_ADDR_MASK="96" +IPV6_NEXTHOP_PREFIX="2001:0DB8:1" + + +SOURCE_TEST_IFACE="veth_source" +SOURCE_TEST_IP_ADDR="2001:0DB8:1::0:1/96" + +SINK_TEST_IFACE="veth_sink" +# ${SINK_TEST_IFACE} is populated with the following range of IPv6 addresses: +# 2001:0DB8:1::1:1 to 2001:0DB8:1::1:${IPV6_NEXTHOP_ADDR_COUNT} +SINK_LOOPBACK_IFACE="lo" +SINK_LOOPBACK_IP_MASK="128" +SINK_LOOPBACK_IP_ADDR="2001:0DB8:2::1:1" + +nexthop_ip_list="" +termination_signal="" +kernel_softlokup_panic_prev_val="" + +terminate_ns_processes_by_pattern() { + local ns=$1 + local pattern=$2 + + for pid in $(ip netns pids ${ns}); do + [ -e /proc/$pid/cmdline ] && grep -qe "${pattern}" /proc/$pid/cmdline && kill -9 $pid + done +} + +cleanup() { + echo "info: cleaning up namespaces and terminating all processes within them..." + + + # Terminate iperf3 instances running in the source_ns. To avoid race + # conditions, first iterate over the PIDs and terminate those + # associated with the bash shells running the + # `while true; do iperf3 -c ...; done` loops. In a second iteration, + # terminate the individual `iperf3 -c ...` instances. + terminate_ns_processes_by_pattern ${source_ns} while + terminate_ns_processes_by_pattern ${source_ns} iperf3 + + # Repeat the same process for sink_ns + terminate_ns_processes_by_pattern ${sink_ns} while + terminate_ns_processes_by_pattern ${sink_ns} iperf3 + + # Check if any iperf3 instances are still running. This could happen + # if a core has entered an infinite loop and the timeout for detecting + # the soft lockup has not expired, but either the test interval has + # already elapsed or the test was terminated manually (e.g., with ^C) + for pid in $(ip netns pids ${source_ns}); do + if [ -e /proc/$pid/cmdline ] && grep -qe 'iperf3' /proc/$pid/cmdline; then + echo "FAIL: unable to terminate some iperf3 instances. Soft lockup is underway. A kernel panic is on the way!" + exit ${ksft_fail} + fi + done + + if [ "$termination_signal" == "SIGINT" ]; then + echo "SKIP: Termination due to ^C (SIGINT)" + elif [ "$termination_signal" == "SIGALRM" ]; then + echo "PASS: No kernel soft lockup occurred during this ${TEST_DURATION} second test" + fi + + cleanup_ns ${source_ns} ${sink_ns} + + sysctl -qw kernel.softlockup_panic=${kernel_softlokup_panic_prev_val} +} + +setup_prepare() { + setup_ns source_ns sink_ns + + ip -n ${source_ns} link add name ${SOURCE_TEST_IFACE} type veth peer name ${SINK_TEST_IFACE} netns ${sink_ns} + + # Setting up the Source namespace + ip -n ${source_ns} addr add ${SOURCE_TEST_IP_ADDR} dev ${SOURCE_TEST_IFACE} + ip -n ${source_ns} link set dev ${SOURCE_TEST_IFACE} qlen 10000 + ip -n ${source_ns} link set dev ${SOURCE_TEST_IFACE} up + ip netns exec ${source_ns} sysctl -qw net.ipv6.fib_multipath_hash_policy=1 + + # Setting up the Sink namespace + ip -n ${sink_ns} addr add ${SINK_LOOPBACK_IP_ADDR}/${SINK_LOOPBACK_IP_MASK} dev ${SINK_LOOPBACK_IFACE} + ip -n ${sink_ns} link set dev ${SINK_LOOPBACK_IFACE} up + ip netns exec ${sink_ns} sysctl -qw net.ipv6.conf.${SINK_LOOPBACK_IFACE}.forwarding=1 + + ip -n ${sink_ns} link set ${SINK_TEST_IFACE} up + ip netns exec ${sink_ns} sysctl -qw net.ipv6.conf.${SINK_TEST_IFACE}.forwarding=1 + + + # Populate nexthop IPv6 addresses on the test interface in the sink_ns + echo "info: populating ${IPV6_NEXTHOP_ADDR_COUNT} IPv6 addresses on the ${SINK_TEST_IFACE} interface ..." + for IP in $(seq 1 ${IPV6_NEXTHOP_ADDR_COUNT}); do + ip -n ${sink_ns} addr add ${IPV6_NEXTHOP_PREFIX}::$(printf "1:%x" "${IP}")/${IPV6_NEXTHOP_ADDR_MASK} dev ${SINK_TEST_IFACE}; + done + + # Preparing list of nexthops + for IP in $(seq 1 ${IPV6_NEXTHOP_ADDR_COUNT}); do + nexthop_ip_list=$nexthop_ip_list" nexthop via ${IPV6_NEXTHOP_PREFIX}::$(printf "1:%x" $IP) dev ${SOURCE_TEST_IFACE} weight 1" + done +} + + +test_soft_lockup_during_routing_table_refresh() { + # Start num_of_iperf_servers iperf3 servers in the sink_ns namespace, + # each listening on ports starting at 5001 and incrementing + # sequentially. Since iperf3 instances may terminate unexpectedly, a + # while loop is used to automatically restart them in such cases. + echo "info: starting ${num_of_iperf_servers} iperf3 servers in the sink_ns namespace ..." + for i in $(seq 1 ${num_of_iperf_servers}); do + cmd="iperf3 --bind ${SINK_LOOPBACK_IP_ADDR} -s -p $(printf '5%03d' ${i}) --rcv-timeout 200 &>/dev/null" + ip netns exec ${sink_ns} bash -c "while true; do ${cmd}; done &" &>/dev/null + done + + # Wait for the iperf3 servers to be ready + for i in $(seq ${num_of_iperf_servers}); do + port=$(printf '5%03d' ${i}); + wait_local_port_listen ${sink_ns} ${port} tcp + done + + # Continuously refresh the routing table in the background within + # the source_ns namespace + ip netns exec ${source_ns} bash -c " + while \$(ip netns list | grep -q ${source_ns}); do + ip -6 route add ${SINK_LOOPBACK_IP_ADDR}/${SINK_LOOPBACK_IP_MASK} ${nexthop_ip_list}; + sleep ${ROUTING_TABLE_REFRESH_PERIOD}; + ip -6 route delete ${SINK_LOOPBACK_IP_ADDR}/${SINK_LOOPBACK_IP_MASK}; + done &" + + # Start num_of_iperf_servers iperf3 clients in the source_ns namespace, + # each sending TCP traffic on sequential ports starting at 5001. + # Since iperf3 instances may terminate unexpectedly (e.g., if the route + # to the server is deleted in the background during a route refresh), a + # while loop is used to automatically restart them in such cases. + echo "info: starting ${num_of_iperf_servers} iperf3 clients in the source_ns namespace ..." + for i in $(seq 1 ${num_of_iperf_servers}); do + cmd="iperf3 -c ${SINK_LOOPBACK_IP_ADDR} -p $(printf '5%03d' ${i}) --length 64 --bitrate ${IPERF3_BITRATE} -t 0 --connect-timeout 150 &>/dev/null" + ip netns exec ${source_ns} bash -c "while true; do ${cmd}; done &" &>/dev/null + done + + echo "info: IPv6 routing table is being updated at the rate of $(echo "1/${ROUTING_TABLE_REFRESH_PERIOD}" | bc)/s for ${TEST_DURATION} seconds ..." + echo "info: A kernel soft lockup, if detected, results in a kernel panic!" + + wait +} + +# Make sure 'iperf3' is installed, skip the test otherwise +if [ ! -x "$(command -v "iperf3")" ]; then + echo "SKIP: 'iperf3' is not installed. Skipping the test." + exit ${ksft_skip} +fi + +# Determine the number of cores on the machine +num_of_iperf_servers=$(( $(nproc)/2 )) + +# Check if we are running on a multi-core machine, skip the test otherwise +if [ "${num_of_iperf_servers}" -eq 0 ]; then + echo "SKIP: This test is not valid on a single core machine!" + exit ${ksft_skip} +fi + +# Since the kernel soft lockup we're testing causes at least one core to enter +# an infinite loop, destabilizing the host and likely affecting subsequent +# tests, we trigger a kernel panic instead of reporting a failure and +# continuing +kernel_softlokup_panic_prev_val=$(sysctl -n kernel.softlockup_panic) +sysctl -qw kernel.softlockup_panic=1 + +handle_sigint() { + termination_signal="SIGINT" + cleanup + exit ${ksft_skip} +} + +handle_sigalrm() { + termination_signal="SIGALRM" + cleanup + exit ${ksft_pass} +} + +trap handle_sigint SIGINT +trap handle_sigalrm SIGALRM + +(sleep ${TEST_DURATION} && kill -s SIGALRM $$)& + +setup_prepare +test_soft_lockup_during_routing_table_refresh -- 2.43.0

11 months, 4 weeks

3
2
0 0

[PATCH net-next 0/8] macsec: inherit lower device's features and TSO limits when offloading

by Sabrina Dubroca

When macsec is offloaded to a NIC, we can take advantage of some of its features, mainly TSO and checksumming. This increases performance significantly. Some features cannot be inherited, because they require additional ops that aren't provided by the macsec netdevice. We also need to inherit TSO limits from the lower device, like VLAN/macvlan devices do. This series also moves the existing macsec offload selftest to the netdevsim selftests before adding tests for the new features. To allow this new selftest to work, netdevsim's hw_features are expanded. Sabrina Dubroca (8): netdevsim: add more hw_features selftests: netdevsim: add a test checking ethtool features macsec: add some of the lower device's features when offloading macsec: clean up local variables in macsec_notify macsec: inherit lower device's TSO limits when offloading selftests: move macsec offload tests from net/rtnetlink to drivers/net/netdvesim selftests: netdevsim: add test toggling macsec offload selftests: netdevsim: add ethtool features to macsec offload tests drivers/net/macsec.c | 64 +++++++--- drivers/net/netdevsim/netdev.c | 6 +- .../selftests/drivers/net/netdevsim/Makefile | 2 + .../selftests/drivers/net/netdevsim/config | 1 + .../drivers/net/netdevsim/ethtool-features.sh | 31 +++++ .../drivers/net/netdevsim/macsec-offload.sh | 117 ++++++++++++++++++ tools/testing/selftests/net/rtnetlink.sh | 68 ---------- 7 files changed, 200 insertions(+), 89 deletions(-) create mode 100644 tools/testing/selftests/drivers/net/netdevsim/ethtool-features.sh create mode 100755 tools/testing/selftests/drivers/net/netdevsim/macsec-offload.sh -- 2.47.0

11 months, 4 weeks

3
17
0 0

2025

2024

2023

2022

2021

2020

2019

2018

2017

Linux-kselftest-mirror