From: Hugo Villeneuve hvilleneuve@dimonoff.com

If an error occurs during probing, the sc16is7xx_lines bitfield may be left in a state that doesn't represent the correct state of lines allocation.

For example, in a system with two SC16 devices, if an error occurs only during probing of channel (port) B of the second device, sc16is7xx_lines final state will be 00001011b instead of the expected 00000011b.

This is caused in part because of the "i--" in the for/loop located in the out_ports: error path.

Fix this by checking the return value of uart_add_one_port() and set line allocation bit only if this was successful. This allows the refactor of the obfuscated for(i--...) loop in the error path, and properly call uart_remove_one_port() only when needed, and properly unset line allocation bits.

Also use same mechanism in remove() when calling uart_remove_one_port().

Fixes: c64349722d14 ("sc16is7xx: support multiple devices") Cc: stable@vger.kernel.org Cc: Yury Norov yury.norov@gmail.com Signed-off-by: Hugo Villeneuve hvilleneuve@dimonoff.com --- drivers/tty/serial/sc16is7xx.c | 44 ++++++++++++++-------------------- 1 file changed, 18 insertions(+), 26 deletions(-)

diff --git a/drivers/tty/serial/sc16is7xx.c b/drivers/tty/serial/sc16is7xx.c index e40e4a99277e..17b90f971f96 100644 --- a/drivers/tty/serial/sc16is7xx.c +++ b/drivers/tty/serial/sc16is7xx.c @@ -407,19 +407,6 @@ static void sc16is7xx_port_update(struct uart_port *port, u8 reg, regmap_update_bits(one->regmap, reg, mask, val); }

-static int sc16is7xx_alloc_line(void) -{ - int i; - - BUILD_BUG_ON(SC16IS7XX_MAX_DEVS > BITS_PER_LONG); - - for (i = 0; i < SC16IS7XX_MAX_DEVS; i++) - if (!test_and_set_bit(i, &sc16is7xx_lines)) - break; - - return i; -} - static void sc16is7xx_power(struct uart_port *port, int on) { sc16is7xx_port_update(port, SC16IS7XX_IER_REG, @@ -1550,6 +1537,13 @@ static int sc16is7xx_probe(struct device *dev, SC16IS7XX_IOCONTROL_SRESET_BIT);

for (i = 0; i < devtype->nr_uart; ++i) { + s->p[i].port.line = find_first_zero_bit(&sc16is7xx_lines, + SC16IS7XX_MAX_DEVS); + if (s->p[i].port.line >= SC16IS7XX_MAX_DEVS) { + ret = -ERANGE; + goto out_ports; + } + /* Initialize port data */ s->p[i].port.dev = dev; s->p[i].port.irq = irq; @@ -1569,14 +1563,8 @@ static int sc16is7xx_probe(struct device *dev, s->p[i].port.rs485_supported = sc16is7xx_rs485_supported; s->p[i].port.ops = &sc16is7xx_ops; s->p[i].old_mctrl = 0; - s->p[i].port.line = sc16is7xx_alloc_line(); s->p[i].regmap = regmaps[i];

- if (s->p[i].port.line >= SC16IS7XX_MAX_DEVS) { - ret = -ENOMEM; - goto out_ports; - } - mutex_init(&s->p[i].efr_lock);

ret = uart_get_rs485_mode(&s->p[i].port); @@ -1594,8 +1582,13 @@ static int sc16is7xx_probe(struct device *dev, kthread_init_work(&s->p[i].tx_work, sc16is7xx_tx_proc); kthread_init_work(&s->p[i].reg_work, sc16is7xx_reg_proc); kthread_init_delayed_work(&s->p[i].ms_work, sc16is7xx_ms_proc); + /* Register port */ - uart_add_one_port(&sc16is7xx_uart, &s->p[i].port); + ret = uart_add_one_port(&sc16is7xx_uart, &s->p[i].port); + if (ret) + goto out_ports; + + set_bit(s->p[i].port.line, &sc16is7xx_lines);

/* Enable EFR */ sc16is7xx_port_write(&s->p[i].port, SC16IS7XX_LCR_REG, @@ -1653,10 +1646,9 @@ static int sc16is7xx_probe(struct device *dev, #endif

out_ports: - for (i--; i >= 0; i--) { - uart_remove_one_port(&sc16is7xx_uart, &s->p[i].port); - clear_bit(s->p[i].port.line, &sc16is7xx_lines); - } + for (i = 0; i < devtype->nr_uart; i++) + if (test_and_clear_bit(s->p[i].port.line, &sc16is7xx_lines)) + uart_remove_one_port(&sc16is7xx_uart, &s->p[i].port);

kthread_stop(s->kworker_task);

@@ -1678,8 +1670,8 @@ static void sc16is7xx_remove(struct device *dev)

for (i = 0; i < s->devtype->nr_uart; i++) { kthread_cancel_delayed_work_sync(&s->p[i].ms_work); - uart_remove_one_port(&sc16is7xx_uart, &s->p[i].port); - clear_bit(s->p[i].port.line, &sc16is7xx_lines); + if (test_and_clear_bit(s->p[i].port.line, &sc16is7xx_lines)) + uart_remove_one_port(&sc16is7xx_uart, &s->p[i].port); sc16is7xx_power(&s->p[i].port, 0); }