When doing a modeset where the sink is transitioning from D3 to D0 , it would sometimes be possible for the initial power_up_phy() to start timing out. This would only be observed in the last action before the sink went into D3 mode was intel_dp_sink_dpms(DRM_MODE_DPMS_OFF). We originally thought this might be an issue with us accidentally shutting off the aux block when putting the sink into D3, but since the DP spec mandates that sinks must wake up within 1ms while we have 100ms to respond to an ESI irq, this didn't really add up. Turns out that the problem is more subtle then that:
It turns out that the timeout is from us not enabling DPMS on the MST hub before actually trying to initiate sideband communications. This would cause the first sideband communication (power_up_phy()), to start timing out because the sink wasn't ready to respond. Afterwards, we would call intel_dp_sink_dpms(DRM_MODE_DPMS_ON) in intel_ddi_pre_enable_dp(), which would actually result in waking up the sink so that sideband requests would work again.
Since DPMS is what lets us actually bring the hub up into a state where sideband communications become functional again, we just need to make sure to enable DPMS on the display before attempting to perform sideband communications.
Changes since v1: - Remove comment above if (!intel_dp->is_mst) - vsryjala - Move intel_dp_sink_dpms() for MST into intel_dp_post_disable_mst() to keep enable/disable paths symmetrical - Improve commit message - dhnkrn
Signed-off-by: Lyude Paul lyude@redhat.com Cc: Dhinakaran Pandiyan dhinakaran.pandiyan@intel.com Cc: Ville Syrjälä ville.syrjala@linux.intel.com Cc: Laura Abbott labbott@redhat.com Cc: stable@vger.kernel.org Fixes: ad260ab32a4d9 ("drm/i915/dp: Write to SET_POWER dpcd to enable MST hub.") --- This email should hopefully actually be picked up by patchwork this time, hooray!
drivers/gpu/drm/i915/intel_ddi.c | 6 ++++-- drivers/gpu/drm/i915/intel_dp_mst.c | 2 ++ 2 files changed, 6 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/i915/intel_ddi.c b/drivers/gpu/drm/i915/intel_ddi.c index a6672a9abd85..c0bf7419e1c1 100644 --- a/drivers/gpu/drm/i915/intel_ddi.c +++ b/drivers/gpu/drm/i915/intel_ddi.c @@ -2324,7 +2324,8 @@ static void intel_ddi_pre_enable_dp(struct intel_encoder *encoder, intel_prepare_dp_ddi_buffers(encoder, crtc_state);
intel_ddi_init_dp_buf_reg(encoder); - intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_ON); + if (!intel_dp->is_mst) + intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_ON); intel_dp_start_link_train(intel_dp); if (port != PORT_A || INTEL_GEN(dev_priv) >= 9) intel_dp_stop_link_train(intel_dp); @@ -2427,7 +2428,8 @@ static void intel_ddi_post_disable_dp(struct intel_encoder *encoder, * Power down sink before disabling the port, otherwise we end * up getting interrupts from the sink on detecting link loss. */ - intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_OFF); + if (!intel_dp->is_mst) + intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_OFF);
intel_disable_ddi_buf(encoder);
diff --git a/drivers/gpu/drm/i915/intel_dp_mst.c b/drivers/gpu/drm/i915/intel_dp_mst.c index c3de0918ee13..2493bd1e0e59 100644 --- a/drivers/gpu/drm/i915/intel_dp_mst.c +++ b/drivers/gpu/drm/i915/intel_dp_mst.c @@ -176,6 +176,7 @@ static void intel_mst_post_disable_dp(struct intel_encoder *encoder, */ drm_dp_send_power_updown_phy(&intel_dp->mst_mgr, connector->port, false); + intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_OFF);
intel_dp->active_mst_links--;
@@ -223,6 +224,7 @@ static void intel_mst_pre_enable_dp(struct intel_encoder *encoder,
DRM_DEBUG_KMS("active links %d\n", intel_dp->active_mst_links);
+ intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_ON); drm_dp_send_power_updown_phy(&intel_dp->mst_mgr, connector->port, true); if (intel_dp->active_mst_links == 0) intel_dig_port->base.pre_enable(&intel_dig_port->base,
Actually - ignore this patch, I'm going to do a v3 because i just noticed there is something very silly and broken I just introduced into the disable codepath
On Thu, 2018-04-05 at 16:36 -0400, Lyude Paul wrote:
When doing a modeset where the sink is transitioning from D3 to D0 , it would sometimes be possible for the initial power_up_phy() to start timing out. This would only be observed in the last action before the sink went into D3 mode was intel_dp_sink_dpms(DRM_MODE_DPMS_OFF). We originally thought this might be an issue with us accidentally shutting off the aux block when putting the sink into D3, but since the DP spec mandates that sinks must wake up within 1ms while we have 100ms to respond to an ESI irq, this didn't really add up. Turns out that the problem is more subtle then that:
It turns out that the timeout is from us not enabling DPMS on the MST hub before actually trying to initiate sideband communications. This would cause the first sideband communication (power_up_phy()), to start timing out because the sink wasn't ready to respond. Afterwards, we would call intel_dp_sink_dpms(DRM_MODE_DPMS_ON) in intel_ddi_pre_enable_dp(), which would actually result in waking up the sink so that sideband requests would work again.
Since DPMS is what lets us actually bring the hub up into a state where sideband communications become functional again, we just need to make sure to enable DPMS on the display before attempting to perform sideband communications.
Changes since v1:
- Remove comment above if (!intel_dp->is_mst) - vsryjala
- Move intel_dp_sink_dpms() for MST into intel_dp_post_disable_mst() to keep enable/disable paths symmetrical
- Improve commit message - dhnkrn
Signed-off-by: Lyude Paul lyude@redhat.com Cc: Dhinakaran Pandiyan dhinakaran.pandiyan@intel.com Cc: Ville Syrjälä ville.syrjala@linux.intel.com Cc: Laura Abbott labbott@redhat.com Cc: stable@vger.kernel.org Fixes: ad260ab32a4d9 ("drm/i915/dp: Write to SET_POWER dpcd to enable MST hub.")
This email should hopefully actually be picked up by patchwork this time, hooray!
drivers/gpu/drm/i915/intel_ddi.c | 6 ++++-- drivers/gpu/drm/i915/intel_dp_mst.c | 2 ++ 2 files changed, 6 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/i915/intel_ddi.c b/drivers/gpu/drm/i915/intel_ddi.c index a6672a9abd85..c0bf7419e1c1 100644 --- a/drivers/gpu/drm/i915/intel_ddi.c +++ b/drivers/gpu/drm/i915/intel_ddi.c @@ -2324,7 +2324,8 @@ static void intel_ddi_pre_enable_dp(struct intel_encoder *encoder, intel_prepare_dp_ddi_buffers(encoder, crtc_state); intel_ddi_init_dp_buf_reg(encoder);
- intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_ON);
- if (!intel_dp->is_mst)
intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_ON);@@ -2427,7 +2428,8 @@ static void intel_ddi_post_disable_dp(struct intel_encoder *encoder, * Power down sink before disabling the port, otherwise we end * up getting interrupts from the sink on detecting link loss. */
- intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_OFF);
- if (!intel_dp->is_mst)
intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_OFF);intel_disable_ddi_buf(encoder); diff --git a/drivers/gpu/drm/i915/intel_dp_mst.c b/drivers/gpu/drm/i915/intel_dp_mst.c index c3de0918ee13..2493bd1e0e59 100644 --- a/drivers/gpu/drm/i915/intel_dp_mst.c +++ b/drivers/gpu/drm/i915/intel_dp_mst.c @@ -176,6 +176,7 @@ static void intel_mst_post_disable_dp(struct intel_encoder *encoder, */ drm_dp_send_power_updown_phy(&intel_dp->mst_mgr, connector->port, false);
- intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_OFF);
intel_dp->active_mst_links--; @@ -223,6 +224,7 @@ static void intel_mst_pre_enable_dp(struct intel_encoder *encoder, DRM_DEBUG_KMS("active links %d\n", intel_dp->active_mst_links);
- intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_ON); drm_dp_send_power_updown_phy(&intel_dp->mst_mgr, connector->port,
true); if (intel_dp->active_mst_links == 0) intel_dig_port->base.pre_enable(&intel_dig_port->base,
On Thu, 2018-04-05 at 16:36 -0400, Lyude Paul wrote:
When doing a modeset where the sink is transitioning from D3 to D0 , it would sometimes be possible for the initial power_up_phy() to start timing out. This would only be observed in the last action before the sink went into D3 mode was intel_dp_sink_dpms(DRM_MODE_DPMS_OFF). We originally thought this might be an issue with us accidentally shutting off the aux block when putting the sink into D3, but since the DP spec mandates that sinks must wake up within 1ms while we have 100ms to respond to an ESI irq, this didn't really add up. Turns out that the problem is more subtle then that:
It turns out that the timeout is from us not enabling DPMS on the MST hub before actually trying to initiate sideband communications. This would cause the first sideband communication (power_up_phy()), to start timing out because the sink wasn't ready to respond. Afterwards, we would call intel_dp_sink_dpms(DRM_MODE_DPMS_ON) in intel_ddi_pre_enable_dp(), which would actually result in waking up the sink so that sideband requests would work again.
Since DPMS is what lets us actually bring the hub up into a state where sideband communications become functional again, we just need to make sure to enable DPMS on the display before attempting to perform sideband communications.
Changes since v1:
- Remove comment above if (!intel_dp->is_mst) - vsryjala
- Move intel_dp_sink_dpms() for MST into intel_dp_post_disable_mst() to keep enable/disable paths symmetrical
- Improve commit message - dhnkrn
Signed-off-by: Lyude Paul lyude@redhat.com Cc: Dhinakaran Pandiyan dhinakaran.pandiyan@intel.com Cc: Ville Syrjälä ville.syrjala@linux.intel.com Cc: Laura Abbott labbott@redhat.com Cc: stable@vger.kernel.org Fixes: ad260ab32a4d9 ("drm/i915/dp: Write to SET_POWER dpcd to enable MST hub.")
This email should hopefully actually be picked up by patchwork this time, hooray!
drivers/gpu/drm/i915/intel_ddi.c | 6 ++++-- drivers/gpu/drm/i915/intel_dp_mst.c | 2 ++ 2 files changed, 6 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/i915/intel_ddi.c b/drivers/gpu/drm/i915/intel_ddi.c index a6672a9abd85..c0bf7419e1c1 100644 --- a/drivers/gpu/drm/i915/intel_ddi.c +++ b/drivers/gpu/drm/i915/intel_ddi.c @@ -2324,7 +2324,8 @@ static void intel_ddi_pre_enable_dp(struct intel_encoder *encoder, intel_prepare_dp_ddi_buffers(encoder, crtc_state); intel_ddi_init_dp_buf_reg(encoder);
- intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_ON);
- if (!intel_dp->is_mst)
intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_ON);@@ -2427,7 +2428,8 @@ static void intel_ddi_post_disable_dp(struct intel_encoder *encoder, * Power down sink before disabling the port, otherwise we end * up getting interrupts from the sink on detecting link loss. */
- intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_OFF);
- if (!intel_dp->is_mst)
intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_OFF);intel_disable_ddi_buf(encoder); diff --git a/drivers/gpu/drm/i915/intel_dp_mst.c b/drivers/gpu/drm/i915/intel_dp_mst.c index c3de0918ee13..2493bd1e0e59 100644 --- a/drivers/gpu/drm/i915/intel_dp_mst.c +++ b/drivers/gpu/drm/i915/intel_dp_mst.c @@ -176,6 +176,7 @@ static void intel_mst_post_disable_dp(struct intel_encoder *encoder, */ drm_dp_send_power_updown_phy(&intel_dp->mst_mgr, connector->port, false);
- intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_OFF);
Needed only when _links goes from 1 -> 0
intel_dp->active_mst_links--; @@ -223,6 +224,7 @@ static void intel_mst_pre_enable_dp(struct intel_encoder *encoder, DRM_DEBUG_KMS("active links %d\n", intel_dp->active_mst_links);
- intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_ON);
Needed only when _links goes from 0 -> 1
drm_dp_send_power_updown_phy(&intel_dp->mst_mgr, connector->port, true); if (intel_dp->active_mst_links == 0) intel_dig_port->base.pre_enable(&intel_dig_port->base,
When doing a modeset where the sink is transitioning from D3 to D0 , it would sometimes be possible for the initial power_up_phy() to start timing out. This would only be observed in the last action before the sink went into D3 mode was intel_dp_sink_dpms(DRM_MODE_DPMS_OFF). We originally thought this might be an issue with us accidentally shutting off the aux block when putting the sink into D3, but since the DP spec mandates that sinks must wake up within 1ms while we have 100ms to respond to an ESI irq, this didn't really add up. Turns out that the problem is more subtle then that:
It turns out that the timeout is from us not enabling DPMS on the MST hub before actually trying to initiate sideband communications. This would cause the first sideband communication (power_up_phy()), to start timing out because the sink wasn't ready to respond. Afterwards, we would call intel_dp_sink_dpms(DRM_MODE_DPMS_ON) in intel_ddi_pre_enable_dp(), which would actually result in waking up the sink so that sideband requests would work again.
Since DPMS is what lets us actually bring the hub up into a state where sideband communications become functional again, we just need to make sure to enable DPMS on the display before attempting to perform sideband communications.
Changes since v1: - Remove comment above if (!intel_dp->is_mst) - vsryjala - Move intel_dp_sink_dpms() for MST into intel_dp_post_disable_mst() to keep enable/disable paths symmetrical - Improve commit message - dhnkrn Changes since v2: - Only send DPMS off when we're disabling the last sink, and only send DPMS on when we're enabling the first sink - dhnkrn
Signed-off-by: Lyude Paul lyude@redhat.com Cc: Dhinakaran Pandiyan dhinakaran.pandiyan@intel.com Cc: Ville Syrjälä ville.syrjala@linux.intel.com Cc: Laura Abbott labbott@redhat.com Cc: stable@vger.kernel.org Fixes: ad260ab32a4d9 ("drm/i915/dp: Write to SET_POWER dpcd to enable MST hub.") --- drivers/gpu/drm/i915/intel_ddi.c | 6 ++++-- drivers/gpu/drm/i915/intel_dp_mst.c | 8 +++++++- 2 files changed, 11 insertions(+), 3 deletions(-)
diff --git a/drivers/gpu/drm/i915/intel_ddi.c b/drivers/gpu/drm/i915/intel_ddi.c index a6672a9abd85..c0bf7419e1c1 100644 --- a/drivers/gpu/drm/i915/intel_ddi.c +++ b/drivers/gpu/drm/i915/intel_ddi.c @@ -2324,7 +2324,8 @@ static void intel_ddi_pre_enable_dp(struct intel_encoder *encoder, intel_prepare_dp_ddi_buffers(encoder, crtc_state);
intel_ddi_init_dp_buf_reg(encoder); - intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_ON); + if (!intel_dp->is_mst) + intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_ON); intel_dp_start_link_train(intel_dp); if (port != PORT_A || INTEL_GEN(dev_priv) >= 9) intel_dp_stop_link_train(intel_dp); @@ -2427,7 +2428,8 @@ static void intel_ddi_post_disable_dp(struct intel_encoder *encoder, * Power down sink before disabling the port, otherwise we end * up getting interrupts from the sink on detecting link loss. */ - intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_OFF); + if (!intel_dp->is_mst) + intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_OFF);
intel_disable_ddi_buf(encoder);
diff --git a/drivers/gpu/drm/i915/intel_dp_mst.c b/drivers/gpu/drm/i915/intel_dp_mst.c index c3de0918ee13..9e6956c08688 100644 --- a/drivers/gpu/drm/i915/intel_dp_mst.c +++ b/drivers/gpu/drm/i915/intel_dp_mst.c @@ -180,9 +180,11 @@ static void intel_mst_post_disable_dp(struct intel_encoder *encoder, intel_dp->active_mst_links--;
intel_mst->connector = NULL; - if (intel_dp->active_mst_links == 0) + if (intel_dp->active_mst_links == 0) { + intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_OFF); intel_dig_port->base.post_disable(&intel_dig_port->base, old_crtc_state, NULL); + }
DRM_DEBUG_KMS("active links %d\n", intel_dp->active_mst_links); } @@ -223,7 +225,11 @@ static void intel_mst_pre_enable_dp(struct intel_encoder *encoder,
DRM_DEBUG_KMS("active links %d\n", intel_dp->active_mst_links);
+ if (intel_dp->active_mst_links == 0) + intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_ON); + drm_dp_send_power_updown_phy(&intel_dp->mst_mgr, connector->port, true); + if (intel_dp->active_mst_links == 0) intel_dig_port->base.pre_enable(&intel_dig_port->base, pipe_config, NULL);
On Thu, 2018-04-05 at 17:19 -0400, Lyude Paul wrote:
When doing a modeset where the sink is transitioning from D3 to D0 , it would sometimes be possible for the initial power_up_phy() to start timing out. This would only be observed in the last action before the sink went into D3 mode was intel_dp_sink_dpms(DRM_MODE_DPMS_OFF). We originally thought this might be an issue with us accidentally shutting off the aux block when putting the sink into D3, but since the DP spec mandates that sinks must wake up within 1ms while we have 100ms to respond to an ESI irq, this didn't really add up. Turns out that the problem is more subtle then that:
It turns out that the timeout is from us not enabling DPMS on the MST hub before actually trying to initiate sideband communications. This would cause the first sideband communication (power_up_phy()), to start timing out because the sink wasn't ready to respond. Afterwards, we would call intel_dp_sink_dpms(DRM_MODE_DPMS_ON) in intel_ddi_pre_enable_dp(), which would actually result in waking up the sink so that sideband requests would work again.
Since DPMS is what lets us actually bring the hub up into a state where sideband communications become functional again, we just need to make sure to enable DPMS on the display before attempting to perform sideband communications.
Changes since v1:
- Remove comment above if (!intel_dp->is_mst) - vsryjala
- Move intel_dp_sink_dpms() for MST into intel_dp_post_disable_mst() to keep enable/disable paths symmetrical
- Improve commit message - dhnkrn
Changes since v2:
- Only send DPMS off when we're disabling the last sink, and only send DPMS on when we're enabling the first sink - dhnkrn
Signed-off-by: Lyude Paul lyude@redhat.com Cc: Dhinakaran Pandiyan dhinakaran.pandiyan@intel.com Cc: Ville Syrjälä ville.syrjala@linux.intel.com Cc: Laura Abbott labbott@redhat.com Cc: stable@vger.kernel.org Fixes: ad260ab32a4d9 ("drm/i915/dp: Write to SET_POWER dpcd to enable MST hub.")
drivers/gpu/drm/i915/intel_ddi.c | 6 ++++-- drivers/gpu/drm/i915/intel_dp_mst.c | 8 +++++++- 2 files changed, 11 insertions(+), 3 deletions(-)
diff --git a/drivers/gpu/drm/i915/intel_ddi.c b/drivers/gpu/drm/i915/intel_ddi.c index a6672a9abd85..c0bf7419e1c1 100644 --- a/drivers/gpu/drm/i915/intel_ddi.c +++ b/drivers/gpu/drm/i915/intel_ddi.c @@ -2324,7 +2324,8 @@ static void intel_ddi_pre_enable_dp(struct intel_encoder *encoder, intel_prepare_dp_ddi_buffers(encoder, crtc_state); intel_ddi_init_dp_buf_reg(encoder);
- intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_ON);
- if (!intel_dp->is_mst)
intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_ON);
I believe Ville recommended to check for is_mst = intel_crtc_has_type(crtc_state, INTEL_OUTPUT_DP_MST) here. The question is, are there cases where intel_dp->is_mst != is_mst? A disconnect in the middle of a modeset would cause intel_dp->is_mst to be false, wouldn't it?
On Thu, 2018-04-05 at 17:19 -0400, Lyude Paul wrote:
When doing a modeset where the sink is transitioning from D3 to D0 , it would sometimes be possible for the initial power_up_phy() to start timing out. This would only be observed in the last action before the sink went into D3 mode was intel_dp_sink_dpms(DRM_MODE_DPMS_OFF). We originally thought this might be an issue with us accidentally shutting off the aux block when putting the sink into D3, but since the DP spec mandates that sinks must wake up within 1ms while we have 100ms to respond to an ESI irq, this didn't really add up. Turns out that the problem is more subtle then that:
It turns out that the timeout is from us not enabling DPMS on the MST hub before actually trying to initiate sideband communications. This would cause the first sideband communication (power_up_phy()), to start timing out because the sink wasn't ready to respond. Afterwards, we would call intel_dp_sink_dpms(DRM_MODE_DPMS_ON) in intel_ddi_pre_enable_dp(), which would actually result in waking up the sink so that sideband requests would work again.
Since DPMS is what lets us actually bring the hub up into a state where sideband communications become functional again, we just need to make sure to enable DPMS on the display before attempting to perform sideband communications.
Changes since v1:
- Remove comment above if (!intel_dp->is_mst) - vsryjala
- Move intel_dp_sink_dpms() for MST into intel_dp_post_disable_mst() to keep enable/disable paths symmetrical
- Improve commit message - dhnkrn
Changes since v2:
- Only send DPMS off when we're disabling the last sink, and only send DPMS on when we're enabling the first sink - dhnkrn
Signed-off-by: Lyude Paul lyude@redhat.com Cc: Dhinakaran Pandiyan dhinakaran.pandiyan@intel.com Cc: Ville Syrjälä ville.syrjala@linux.intel.com Cc: Laura Abbott labbott@redhat.com Cc: stable@vger.kernel.org Fixes: ad260ab32a4d9 ("drm/i915/dp: Write to SET_POWER dpcd to enable MST hub.")
drivers/gpu/drm/i915/intel_ddi.c | 6 ++++-- drivers/gpu/drm/i915/intel_dp_mst.c | 8 +++++++- 2 files changed, 11 insertions(+), 3 deletions(-)
diff --git a/drivers/gpu/drm/i915/intel_ddi.c b/drivers/gpu/drm/i915/intel_ddi.c index a6672a9abd85..c0bf7419e1c1 100644 --- a/drivers/gpu/drm/i915/intel_ddi.c +++ b/drivers/gpu/drm/i915/intel_ddi.c @@ -2324,7 +2324,8 @@ static void intel_ddi_pre_enable_dp(struct intel_encoder *encoder, intel_prepare_dp_ddi_buffers(encoder, crtc_state); intel_ddi_init_dp_buf_reg(encoder);
- intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_ON);
- if (!intel_dp->is_mst)
intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_ON);
I believe Ville recommended to check for is_mst = intel_crtc_has_type(crtc_state, INTEL_OUTPUT_DP_MST) here. The question is, are there cases where intel_dp->is_mst != is_mst? A disconnect in the middle of a modeset would cause intel_dp->is_mst to be false, wouldn't it?
Hi,
[This is an automated email]
This commit has been processed because it contains a "Fixes:" tag, fixing commit: .
The bot has also determined it's probably a bug fixing patch. (score: 97.3902)
The bot has tested the following trees: v4.16.1, v4.15.16, v4.14.33, v4.9.93, v4.4.127.
v4.16.1: Build OK! v4.15.16: Failed to apply! Possible dependencies: 1939ba51fd05 ("drm/i915: Pass a crtc state to ddi post_disable from MST code")
v4.14.33: Failed to apply! Possible dependencies: 1939ba51fd05 ("drm/i915: Pass a crtc state to ddi post_disable from MST code") 5ea2355a100a ("drm/i915/mst: Use MST sideband message transactions for dpms control") b1e314462bba ("drm/i915/dp: Write to SET_POWER dpcd to enable MST hub.") c5f93fcf2ee1 ("drm/i915: Disable infoframes when shutting down DDI HDMI") f45f3da7c4f6 ("drm/i915: Split intel_ddi_post_disable() into DP vs. HDMI variants")
v4.9.93: Failed to apply! Possible dependencies: 1939ba51fd05 ("drm/i915: Pass a crtc state to ddi post_disable from MST code") 5ea2355a100a ("drm/i915/mst: Use MST sideband message transactions for dpms control") b1e314462bba ("drm/i915/dp: Write to SET_POWER dpcd to enable MST hub.") c5f93fcf2ee1 ("drm/i915: Disable infoframes when shutting down DDI HDMI") e081c8463ac9 ("drm/i915: Remove duplicate DDI enabling logic from MST path") f45f3da7c4f6 ("drm/i915: Split intel_ddi_post_disable() into DP vs. HDMI variants")
v4.4.127: Failed to apply! Possible dependencies: 0552f7651bc2 ("drm/i915/mst: use reference counted connectors. (v3)") 1939ba51fd05 ("drm/i915: Pass a crtc state to ddi post_disable from MST code") 5ea2355a100a ("drm/i915/mst: Use MST sideband message transactions for dpms control") b1e314462bba ("drm/i915/dp: Write to SET_POWER dpcd to enable MST hub.") ba88d153526f ("drm/i915: Split intel_ddi_pre_enable() into DP and HDMI versions") c5f93fcf2ee1 ("drm/i915: Disable infoframes when shutting down DDI HDMI") e081c8463ac9 ("drm/i915: Remove duplicate DDI enabling logic from MST path") f45f3da7c4f6 ("drm/i915: Split intel_ddi_post_disable() into DP vs. HDMI variants") fd6bbda9c7a4 ("drm/i915: Pass crtc_state and connector_state to encoder functions")
-- Thanks, Sasha
Hi,
[This is an automated email]
This commit has been processed because it contains a "Fixes:" tag, fixing commit: .
The bot has also determined it's probably a bug fixing patch. (score: 98.1292)
The bot has tested the following trees: v4.16.1, v4.15.16, v4.14.33, v4.9.93, v4.4.127.
v4.16.1: Build OK! v4.15.16: Build OK! v4.14.33: Failed to apply! Possible dependencies: 5ea2355a100a ("drm/i915/mst: Use MST sideband message transactions for dpms control") b1e314462bba ("drm/i915/dp: Write to SET_POWER dpcd to enable MST hub.") c5f93fcf2ee1 ("drm/i915: Disable infoframes when shutting down DDI HDMI") f45f3da7c4f6 ("drm/i915: Split intel_ddi_post_disable() into DP vs. HDMI variants")
v4.9.93: Failed to apply! Possible dependencies: 5ea2355a100a ("drm/i915/mst: Use MST sideband message transactions for dpms control") b1e314462bba ("drm/i915/dp: Write to SET_POWER dpcd to enable MST hub.") c5f93fcf2ee1 ("drm/i915: Disable infoframes when shutting down DDI HDMI") f45f3da7c4f6 ("drm/i915: Split intel_ddi_post_disable() into DP vs. HDMI variants")
v4.4.127: Failed to apply! Possible dependencies: 0552f7651bc2 ("drm/i915/mst: use reference counted connectors. (v3)") 5ea2355a100a ("drm/i915/mst: Use MST sideband message transactions for dpms control") b1e314462bba ("drm/i915/dp: Write to SET_POWER dpcd to enable MST hub.") ba88d153526f ("drm/i915: Split intel_ddi_pre_enable() into DP and HDMI versions") c5f93fcf2ee1 ("drm/i915: Disable infoframes when shutting down DDI HDMI") f45f3da7c4f6 ("drm/i915: Split intel_ddi_post_disable() into DP vs. HDMI variants")
-- Thanks, Sasha
linux-stable-mirror@lists.linaro.org
-
Dhinakaran Pandiyan -
Lyude Paul -
Pandiyan, Dhinakaran
-
Sasha Levin