From: Andrey Konovalov andrey.konovalov@linaro.org

In the current driver csid Test Pattern Generator (TPG) doesn't work. This change: - fixes writing frame width and height values into CSID_TPG_DT_n_CFG_0 - fixes the shift by one between test_pattern control value and the actual pattern. So that TPG starts working, but with the below limitations: - only test_pattern=9 works as it should - test_pattern=8 and test_pattern=7 produce black frame (all zeroes) - the rest of test_pattern's don't work (yavta doesn't get the data) - regardless of the CFA pattern set by 'media-ctl -V' the actual pixel order is always the same (RGGB for any RAW8 or RAW10P format in 4608x2592 resolution).

Tested with:

RAW10P format, VC0: media-ctl -V '"msm_csid0":0[fmt:SRGGB10/4608x2592 field:none]' media-ctl -V '"msm_vfe0_rdi0":0[fmt:SRGGB10/4608x2592 field:none]' media-ctl -l '"msm_csid0":1->"msm_vfe0_rdi0":0[1]' v4l2-ctl -d /dev/v4l-subdev6 -c test_pattern=9 yavta -B capture-mplane --capture=3 -n 3 -f SRGGB10P -s 4608x2592 /dev/video0

RAW10P format, VC1: media-ctl -V '"msm_csid0":2[fmt:SRGGB10/4608x2592 field:none]' media-ctl -V '"msm_vfe0_rdi1":0[fmt:SRGGB10/4608x2592 field:none]' media-ctl -l '"msm_csid0":2->"msm_vfe0_rdi1":0[1]' v4l2-ctl -d /dev/v4l-subdev6 -c test_pattern=9 yavta -B capture-mplane --capture=3 -n 3 -f SRGGB10P -s 4608x2592 /dev/video1

RAW8 format, VC0: media-ctl --reset media-ctl -V '"msm_csid0":0[fmt:SRGGB8/4608x2592 field:none]' media-ctl -V '"msm_vfe0_rdi0":0[fmt:SRGGB8/4608x2592 field:none]' media-ctl -l '"msm_csid0":1->"msm_vfe0_rdi0":0[1]' yavta -B capture-mplane --capture=3 -n 3 -f SRGGB8 -s 4608x2592 /dev/video0

Fixes: eebe6d00e9bf ("media: camss: Add support for CSID hardware version Titan 170") Cc: stable@vger.kernel.org Signed-off-by: Andrey Konovalov andrey.konovalov@linaro.org Signed-off-by: Bryan O'Donoghue bryan.odonoghue@linaro.org --- drivers/media/platform/qcom/camss/camss-csid-gen2.c | 9 +++------ 1 file changed, 3 insertions(+), 6 deletions(-)

diff --git a/drivers/media/platform/qcom/camss/camss-csid-gen2.c b/drivers/media/platform/qcom/camss/camss-csid-gen2.c index 140c584bfb8b1..6ba2b10326444 100644 --- a/drivers/media/platform/qcom/camss/camss-csid-gen2.c +++ b/drivers/media/platform/qcom/camss/camss-csid-gen2.c @@ -355,9 +355,6 @@ static void __csid_configure_stream(struct csid_device *csid, u8 enable, u8 vc) u8 dt_id = vc;

if (tg->enabled) { - /* Config Test Generator */ - vc = 0xa; - /* configure one DT, infinite frames */ val = vc << TPG_VC_CFG0_VC_NUM; val |= INTELEAVING_MODE_ONE_SHOT << TPG_VC_CFG0_LINE_INTERLEAVING_MODE; @@ -370,14 +367,14 @@ static void __csid_configure_stream(struct csid_device *csid, u8 enable, u8 vc)

writel_relaxed(0x12345678, csid->base + CSID_TPG_LFSR_SEED);

- val = input_format->height & 0x1fff << TPG_DT_n_CFG_0_FRAME_HEIGHT; - val |= input_format->width & 0x1fff << TPG_DT_n_CFG_0_FRAME_WIDTH; + val = (input_format->height & 0x1fff) << TPG_DT_n_CFG_0_FRAME_HEIGHT; + val |= (input_format->width & 0x1fff) << TPG_DT_n_CFG_0_FRAME_WIDTH; writel_relaxed(val, csid->base + CSID_TPG_DT_n_CFG_0(0));

val = format->data_type << TPG_DT_n_CFG_1_DATA_TYPE; writel_relaxed(val, csid->base + CSID_TPG_DT_n_CFG_1(0));

- val = tg->mode << TPG_DT_n_CFG_2_PAYLOAD_MODE; + val = (tg->mode - 1) << TPG_DT_n_CFG_2_PAYLOAD_MODE; val |= 0xBE << TPG_DT_n_CFG_2_USER_SPECIFIED_PAYLOAD; val |= format->decode_format << TPG_DT_n_CFG_2_ENCODE_FORMAT; writel_relaxed(val, csid->base + CSID_TPG_DT_n_CFG_2(0));