In commit 43c2de1002d2, we moved most HW configuration to bind(), but we didn't move the runtime PM management. Therefore, depending on initial boot state, runtime-PM workqueue delays, and other timing factors, we may disable our power domain in between the hardware configuration (bind()) and when we enable the display. This can cause us to lose hardware state and fail to configure our display. For example:
dw-mipi-dsi-rockchip ff968000.mipi: failed to write command FIFO panel-innolux-p079zca ff960000.mipi.0: failed to write command 0
or:
dw-mipi-dsi-rockchip ff968000.mipi: failed to write command FIFO panel-kingdisplay-kd097d04 ff960000.mipi.0: failed write init cmds: -110
We should match the runtime PM to the lifetime of the bind()/unbind() cycle.
Tested on Acer Chrometab 10 (RK3399 Gru-Scarlet), with panel drivers built either as modules or built-in.
Side notes: it seems one is more likely to see this problem when the panel driver is built into the kernel. I've also seen this problem bisect down to commits that simply changed Kconfig dependencies, because it changed the order in which driver init functions were compiled into the kernel, and therefore the ordering and timing of built-in device probe.
Fixes: 43c2de1002d2 ("drm/rockchip: dsi: move all lane config except LCDC mux to bind()") Link: https://lore.kernel.org/linux-rockchip/9aedfb528600ecf871885f7293ca4207c84d1... Reported-by: aleksandr.o.makarov@gmail.com Cc: stable@vger.kernel.org Signed-off-by: Brian Norris briannorris@chromium.org Tested-by: Nícolas F. R. A. Prado nfraprado@collabora.com ---
Changes in v2: - Clean up pm-runtime state in error cases. - Correct git hash for Fixes.
.../gpu/drm/rockchip/dw-mipi-dsi-rockchip.c | 37 ++++++++++--------- 1 file changed, 19 insertions(+), 18 deletions(-)
diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c index a2262bee5aa4..45676b23c019 100644 --- a/drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c +++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c @@ -773,10 +773,6 @@ static void dw_mipi_dsi_encoder_enable(struct drm_encoder *encoder) if (mux < 0) return;
- pm_runtime_get_sync(dsi->dev); - if (dsi->slave) - pm_runtime_get_sync(dsi->slave->dev); - /* * For the RK3399, the clk of grf must be enabled before writing grf * register. And for RK3288 or other soc, this grf_clk must be NULL, @@ -795,20 +791,10 @@ static void dw_mipi_dsi_encoder_enable(struct drm_encoder *encoder) clk_disable_unprepare(dsi->grf_clk); }
-static void dw_mipi_dsi_encoder_disable(struct drm_encoder *encoder) -{ - struct dw_mipi_dsi_rockchip *dsi = to_dsi(encoder); - - if (dsi->slave) - pm_runtime_put(dsi->slave->dev); - pm_runtime_put(dsi->dev); -} - static const struct drm_encoder_helper_funcs dw_mipi_dsi_encoder_helper_funcs = { .atomic_check = dw_mipi_dsi_encoder_atomic_check, .enable = dw_mipi_dsi_encoder_enable, - .disable = dw_mipi_dsi_encoder_disable, };
static int rockchip_dsi_drm_create_encoder(struct dw_mipi_dsi_rockchip *dsi, @@ -938,10 +924,14 @@ static int dw_mipi_dsi_rockchip_bind(struct device *dev, put_device(second); }
+ pm_runtime_get_sync(dsi->dev); + if (dsi->slave) + pm_runtime_get_sync(dsi->slave->dev); + ret = clk_prepare_enable(dsi->pllref_clk); if (ret) { DRM_DEV_ERROR(dev, "Failed to enable pllref_clk: %d\n", ret); - return ret; + goto out_pm_runtime; }
/* @@ -953,7 +943,7 @@ static int dw_mipi_dsi_rockchip_bind(struct device *dev, ret = clk_prepare_enable(dsi->grf_clk); if (ret) { DRM_DEV_ERROR(dsi->dev, "Failed to enable grf_clk: %d\n", ret); - return ret; + goto out_pm_runtime; }
dw_mipi_dsi_rockchip_config(dsi); @@ -965,16 +955,23 @@ static int dw_mipi_dsi_rockchip_bind(struct device *dev, ret = rockchip_dsi_drm_create_encoder(dsi, drm_dev); if (ret) { DRM_DEV_ERROR(dev, "Failed to create drm encoder\n"); - return ret; + goto out_pm_runtime; }
ret = dw_mipi_dsi_bind(dsi->dmd, &dsi->encoder); if (ret) { DRM_DEV_ERROR(dev, "Failed to bind: %d\n", ret); - return ret; + goto out_pm_runtime; }
return 0; + +out_pm_runtime: + pm_runtime_put(dsi->dev); + if (dsi->slave) + pm_runtime_put(dsi->slave->dev); + + return ret; }
static void dw_mipi_dsi_rockchip_unbind(struct device *dev, @@ -989,6 +986,10 @@ static void dw_mipi_dsi_rockchip_unbind(struct device *dev, dw_mipi_dsi_unbind(dsi->dmd);
clk_disable_unprepare(dsi->pllref_clk); + + pm_runtime_put(dsi->dev); + if (dsi->slave) + pm_runtime_put(dsi->slave->dev); }
static const struct component_ops dw_mipi_dsi_rockchip_ops = {
Reviewed-by: Thomas Hebb tommyhebb@gmail.com
Thank you for catching this, and sorry that my original fix broke things. There had actually been a report of this breakage from my patch, but I missed that email until it had already been merged and then didn't have time to follow up on it. Totally my bad.
[Resending because my last reply was HTML.]
On Mon, Sep 27, 2021 at 11:00 AM Brian Norris briannorris@chromium.org wrote:
In commit 43c2de1002d2, we moved most HW configuration to bind(), but we didn't move the runtime PM management. Therefore, depending on initial boot state, runtime-PM workqueue delays, and other timing factors, we may disable our power domain in between the hardware configuration (bind()) and when we enable the display. This can cause us to lose hardware state and fail to configure our display. For example:
dw-mipi-dsi-rockchip ff968000.mipi: failed to write command FIFO panel-innolux-p079zca ff960000.mipi.0: failed to write command 0
or:
dw-mipi-dsi-rockchip ff968000.mipi: failed to write command FIFO panel-kingdisplay-kd097d04 ff960000.mipi.0: failed write init cmds: -110
We should match the runtime PM to the lifetime of the bind()/unbind() cycle.
Tested on Acer Chrometab 10 (RK3399 Gru-Scarlet), with panel drivers built either as modules or built-in.
Side notes: it seems one is more likely to see this problem when the panel driver is built into the kernel. I've also seen this problem bisect down to commits that simply changed Kconfig dependencies, because it changed the order in which driver init functions were compiled into the kernel, and therefore the ordering and timing of built-in device probe.
Fixes: 43c2de1002d2 ("drm/rockchip: dsi: move all lane config except LCDC mux to bind()") Link: https://lore.kernel.org/linux-rockchip/9aedfb528600ecf871885f7293ca4207c84d1... Reported-by: aleksandr.o.makarov@gmail.com Cc: stable@vger.kernel.org Signed-off-by: Brian Norris briannorris@chromium.org Tested-by: Nícolas F. R. A. Prado nfraprado@collabora.com
Changes in v2:
- Clean up pm-runtime state in error cases.
- Correct git hash for Fixes.
.../gpu/drm/rockchip/dw-mipi-dsi-rockchip.c | 37 ++++++++++--------- 1 file changed, 19 insertions(+), 18 deletions(-)
diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c index a2262bee5aa4..45676b23c019 100644 --- a/drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c +++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c @@ -773,10 +773,6 @@ static void dw_mipi_dsi_encoder_enable(struct drm_encoder *encoder) if (mux < 0) return;
pm_runtime_get_sync(dsi->dev);if (dsi->slave)pm_runtime_get_sync(dsi->slave->dev);/* * For the RK3399, the clk of grf must be enabled before writing grf * register. And for RK3288 or other soc, this grf_clk must be NULL,@@ -795,20 +791,10 @@ static void dw_mipi_dsi_encoder_enable(struct drm_encoder *encoder) clk_disable_unprepare(dsi->grf_clk); }
-static void dw_mipi_dsi_encoder_disable(struct drm_encoder *encoder) -{
struct dw_mipi_dsi_rockchip *dsi = to_dsi(encoder);if (dsi->slave)pm_runtime_put(dsi->slave->dev);pm_runtime_put(dsi->dev);-}
static const struct drm_encoder_helper_funcs dw_mipi_dsi_encoder_helper_funcs = { .atomic_check = dw_mipi_dsi_encoder_atomic_check, .enable = dw_mipi_dsi_encoder_enable,
.disable = dw_mipi_dsi_encoder_disable,};
static int rockchip_dsi_drm_create_encoder(struct dw_mipi_dsi_rockchip *dsi, @@ -938,10 +924,14 @@ static int dw_mipi_dsi_rockchip_bind(struct device *dev, put_device(second); }
pm_runtime_get_sync(dsi->dev);if (dsi->slave)pm_runtime_get_sync(dsi->slave->dev);ret = clk_prepare_enable(dsi->pllref_clk); if (ret) { DRM_DEV_ERROR(dev, "Failed to enable pllref_clk: %d\n", ret);
return ret;
goto out_pm_runtime; } /*@@ -953,7 +943,7 @@ static int dw_mipi_dsi_rockchip_bind(struct device *dev, ret = clk_prepare_enable(dsi->grf_clk); if (ret) { DRM_DEV_ERROR(dsi->dev, "Failed to enable grf_clk: %d\n", ret);
return ret;
goto out_pm_runtime; } dw_mipi_dsi_rockchip_config(dsi);@@ -965,16 +955,23 @@ static int dw_mipi_dsi_rockchip_bind(struct device *dev, ret = rockchip_dsi_drm_create_encoder(dsi, drm_dev); if (ret) { DRM_DEV_ERROR(dev, "Failed to create drm encoder\n");
return ret;
goto out_pm_runtime; } ret = dw_mipi_dsi_bind(dsi->dmd, &dsi->encoder); if (ret) { DRM_DEV_ERROR(dev, "Failed to bind: %d\n", ret);
return ret;
goto out_pm_runtime; } return 0;+out_pm_runtime:
pm_runtime_put(dsi->dev);if (dsi->slave)pm_runtime_put(dsi->slave->dev);return ret;}
static void dw_mipi_dsi_rockchip_unbind(struct device *dev, @@ -989,6 +986,10 @@ static void dw_mipi_dsi_rockchip_unbind(struct device *dev, dw_mipi_dsi_unbind(dsi->dmd);
clk_disable_unprepare(dsi->pllref_clk);
pm_runtime_put(dsi->dev);if (dsi->slave)pm_runtime_put(dsi->slave->dev);}
static const struct component_ops dw_mipi_dsi_rockchip_ops = {
2.33.0.685.g46640cef36-goog
On Mon, Sep 27, 2021 at 12:18 PM Tom Hebb tommyhebb@gmail.com wrote:
Reviewed-by: Thomas Hebb tommyhebb@gmail.com
Thanks!
Thank you for catching this, and sorry that my original fix broke things. There had actually been a report of this breakage from my patch, but I missed that email until it had already been merged and then didn't have time to follow up on it. Totally my bad.
No worries. It was a 1 step forward, 1 step backward kind of a thing anyway -- things were broken in many cases before your patch too (with very similar-looking symptoms) -- so the net result is still good, having both issues fixed.
I'm not sure how that ideally should have been handled [1], but it's totally fair to not have time to follow up on everything. At the worst, we could have reverted things; but again, I'm pretty sure things were broken just as well without your fix, just with a different root cause.
Regards, Brian
[1] Don't accept (or, revert?) your bugfix until what may or may not have been a regression is fixed? I'm not sure.
On Mon, Sep 27, 2021 at 10:59:42AM -0700, Brian Norris wrote:
In commit 43c2de1002d2, we moved most HW configuration to bind(), but we didn't move the runtime PM management. Therefore, depending on initial boot state, runtime-PM workqueue delays, and other timing factors, we may disable our power domain in between the hardware configuration (bind()) and when we enable the display. This can cause us to lose hardware state and fail to configure our display. For example:
dw-mipi-dsi-rockchip ff968000.mipi: failed to write command FIFO panel-innolux-p079zca ff960000.mipi.0: failed to write command 0
or:
dw-mipi-dsi-rockchip ff968000.mipi: failed to write command FIFO panel-kingdisplay-kd097d04 ff960000.mipi.0: failed write init cmds: -110
We should match the runtime PM to the lifetime of the bind()/unbind() cycle.
Hmm, sorry to reply to my own patch so quickly, but after a bit more testing I'm finding we still have yet another problem here -- that suspend/resume does not work. For suspend/resume, drm_mode_config_helper_{suspend,resume}() are expecting to only do teardown/setup via disable()/enable() -- there is no re-bind() (which makes sense). But the DSI hardware state may be lost, so the resume-time enable() may find the panel initialization timing out yet again.
Possible solutions:
(1) I can add PM suspend()/resume() operations just to call dw_mipi_dsi_rockchip_config().
(2) Switch back to using mode_set() for HW configuration, like the downstream/BSP driver does (and the initial versions Rockchip and later Heiko were working on did the same), since that's always called at the right time before both panel and encoder enable(). That also happens to be where some other DSI drivers [1] do similar init.
Have we been avoiding (2) just because that doesn't really match the intended purpose of the callback? I can't find any cleaner callback for this at the moment, and I'd rather not try to introduce entirely new drm helper callbacks just for this particularly-unfriendly sequence.
I have a patch written for option (1), and may send a v3 soon to include that as well (because that's also a regression from the same commit).
Brian
[1] e.g., drivers/gpu/drm/bridge/nwl-dsi.c
linux-stable-mirror@lists.linaro.org
-
Brian Norris -
Tom Hebb