From: Thomas Bartschies thomas.bartschies@cvk.de
[ Upstream commit 015c44d7bff3f44d569716117becd570c179ca32 ]
Since the recent introduction supporting the SM3 and SM4 hash algos for IPsec, the kernel produces invalid pfkey acquire messages, when these encryption modules are disabled. This happens because the availability of the algos wasn't checked in all necessary functions. This patch adds these checks.
Signed-off-by: Thomas Bartschies thomas.bartschies@cvk.de Signed-off-by: Steffen Klassert steffen.klassert@secunet.com Signed-off-by: Sasha Levin sashal@kernel.org --- net/key/af_key.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)
diff --git a/net/key/af_key.c b/net/key/af_key.c index a416c0f90056..e7efd2a9ede7 100644 --- a/net/key/af_key.c +++ b/net/key/af_key.c @@ -2908,7 +2908,7 @@ static int count_ah_combs(const struct xfrm_tmpl *t) break; if (!aalg->pfkey_supported) continue; - if (aalg_tmpl_set(t, aalg)) + if (aalg_tmpl_set(t, aalg) && aalg->available) sz += sizeof(struct sadb_comb); } return sz + sizeof(struct sadb_prop); @@ -2926,7 +2926,7 @@ static int count_esp_combs(const struct xfrm_tmpl *t) if (!ealg->pfkey_supported) continue;
- if (!(ealg_tmpl_set(t, ealg))) + if (!(ealg_tmpl_set(t, ealg) && ealg->available)) continue;
for (k = 1; ; k++) { @@ -2937,7 +2937,7 @@ static int count_esp_combs(const struct xfrm_tmpl *t) if (!aalg->pfkey_supported) continue;
- if (aalg_tmpl_set(t, aalg)) + if (aalg_tmpl_set(t, aalg) && aalg->available) sz += sizeof(struct sadb_comb); } }
From: Joel Stanley joel@jms.id.au
[ Upstream commit 6fd45e79e8b93b8d22fb8fe22c32fbad7e9190bd ]
The AST2600 when using the i210 NIC over NC-SI has been observed to produce incorrect checksum results with specific MTU values. This was first observed when sending data across a long distance set of networks.
On a local network, the following test was performed using a 1MB file of random data.
On the receiver run this script:
#!/bin/bash while [ 1 ]; do # Zero the stats nstat -r > /dev/null nc -l 9899 > test-file # Check for checksum errors TcpInCsumErrors=$(nstat | grep TcpInCsumErrors) if [ -z "$TcpInCsumErrors" ]; then echo No TcpInCsumErrors else echo TcpInCsumErrors = $TcpInCsumErrors fi done
On an AST2600 system:
# nc <IP of receiver host> 9899 < test-file
The test was repeated with various MTU values:
# ip link set mtu 1410 dev eth0
The observed results:
1500 - good 1434 - bad 1400 - good 1410 - bad 1420 - good
The test was repeated after disabling tx checksumming:
# ethtool -K eth0 tx-checksumming off
And all MTU values tested resulted in transfers without error.
An issue with the driver cannot be ruled out, however there has been no bug discovered so far.
David has done the work to take the original bug report of slow data transfer between long distance connections and triaged it down to this test case.
The vendor suspects this this is a hardware issue when using NC-SI. The fixes line refers to the patch that introduced AST2600 support.
Reported-by: David Wilder wilder@us.ibm.com Reviewed-by: Dylan Hung dylan_hung@aspeedtech.com Signed-off-by: Joel Stanley joel@jms.id.au Signed-off-by: David S. Miller davem@davemloft.net Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/net/ethernet/faraday/ftgmac100.c | 5 +++++ 1 file changed, 5 insertions(+)
diff --git a/drivers/net/ethernet/faraday/ftgmac100.c b/drivers/net/ethernet/faraday/ftgmac100.c index 964407deca35..23c019d1278c 100644 --- a/drivers/net/ethernet/faraday/ftgmac100.c +++ b/drivers/net/ethernet/faraday/ftgmac100.c @@ -1869,6 +1869,11 @@ static int ftgmac100_probe(struct platform_device *pdev) /* AST2400 doesn't have working HW checksum generation */ if (np && (of_device_is_compatible(np, "aspeed,ast2400-mac"))) netdev->hw_features &= ~NETIF_F_HW_CSUM; + + /* AST2600 tx checksum with NCSI is broken */ + if (priv->use_ncsi && of_device_is_compatible(np, "aspeed,ast2600-mac")) + netdev->hw_features &= ~NETIF_F_HW_CSUM; + if (np && of_get_property(np, "no-hw-checksum", NULL)) netdev->hw_features &= ~(NETIF_F_HW_CSUM | NETIF_F_RXCSUM); netdev->features |= netdev->hw_features;
From: Mika Westerberg mika.westerberg@linux.intel.com
[ Upstream commit 17a0f3acdc6ec8b89ad40f6e22165a4beee25663 ]
Before sending a MSI the hardware writes information pertinent to the interrupt cause to a memory location pointed by SMTICL register. This memory holds three double words where the least significant bit tells whether the interrupt cause of master/target/error is valid. The driver does not use this but we need to set it up because otherwise it will perform DMA write to the default address (0) and this will cause an IOMMU fault such as below:
DMAR: DRHD: handling fault status reg 2 DMAR: [DMA Write] Request device [00:12.0] PASID ffffffff fault addr 0 [fault reason 05] PTE Write access is not set
To prevent this from happening, provide a proper DMA buffer for this that then gets mapped by the IOMMU accordingly.
Signed-off-by: Mika Westerberg mika.westerberg@linux.intel.com Reviewed-by: From: Andy Shevchenko andriy.shevchenko@linux.intel.com Signed-off-by: Wolfram Sang wsa@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/i2c/busses/i2c-ismt.c | 14 ++++++++++++++ 1 file changed, 14 insertions(+)
diff --git a/drivers/i2c/busses/i2c-ismt.c b/drivers/i2c/busses/i2c-ismt.c index 0d1c3ec8cb40..80796061102f 100644 --- a/drivers/i2c/busses/i2c-ismt.c +++ b/drivers/i2c/busses/i2c-ismt.c @@ -80,6 +80,7 @@
#define ISMT_DESC_ENTRIES 2 /* number of descriptor entries */ #define ISMT_MAX_RETRIES 3 /* number of SMBus retries to attempt */ +#define ISMT_LOG_ENTRIES 3 /* number of interrupt cause log entries */
/* Hardware Descriptor Constants - Control Field */ #define ISMT_DESC_CWRL 0x01 /* Command/Write Length */ @@ -173,6 +174,8 @@ struct ismt_priv { u8 head; /* ring buffer head pointer */ struct completion cmp; /* interrupt completion */ u8 buffer[I2C_SMBUS_BLOCK_MAX + 16]; /* temp R/W data buffer */ + dma_addr_t log_dma; + u32 *log; };
/** @@ -406,6 +409,9 @@ static int ismt_access(struct i2c_adapter *adap, u16 addr, memset(desc, 0, sizeof(struct ismt_desc)); desc->tgtaddr_rw = ISMT_DESC_ADDR_RW(addr, read_write);
+ /* Always clear the log entries */ + memset(priv->log, 0, ISMT_LOG_ENTRIES * sizeof(u32)); + /* Initialize common control bits */ if (likely(pci_dev_msi_enabled(priv->pci_dev))) desc->control = ISMT_DESC_INT | ISMT_DESC_FAIR; @@ -695,6 +701,8 @@ static void ismt_hw_init(struct ismt_priv *priv) /* initialize the Master Descriptor Base Address (MDBA) */ writeq(priv->io_rng_dma, priv->smba + ISMT_MSTR_MDBA);
+ writeq(priv->log_dma, priv->smba + ISMT_GR_SMTICL); + /* initialize the Master Control Register (MCTRL) */ writel(ISMT_MCTRL_MEIE, priv->smba + ISMT_MSTR_MCTRL);
@@ -784,6 +792,12 @@ static int ismt_dev_init(struct ismt_priv *priv) priv->head = 0; init_completion(&priv->cmp);
+ priv->log = dmam_alloc_coherent(&priv->pci_dev->dev, + ISMT_LOG_ENTRIES * sizeof(u32), + &priv->log_dma, GFP_KERNEL); + if (!priv->log) + return -ENOMEM; + return 0; }
From: Piyush Malgujar pmalgujar@marvell.com
[ Upstream commit 03a35bc856ddc09f2cc1f4701adecfbf3b464cb3 ]
Due to i2c->adap.dev.fwnode not being set, ACPI_COMPANION() wasn't properly found for TWSI controllers.
Signed-off-by: Szymon Balcerak sbalcerak@marvell.com Signed-off-by: Piyush Malgujar pmalgujar@marvell.com Signed-off-by: Wolfram Sang wsa@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/i2c/busses/i2c-thunderx-pcidrv.c | 1 + 1 file changed, 1 insertion(+)
diff --git a/drivers/i2c/busses/i2c-thunderx-pcidrv.c b/drivers/i2c/busses/i2c-thunderx-pcidrv.c index 19f8eec38717..107aeb8b54da 100644 --- a/drivers/i2c/busses/i2c-thunderx-pcidrv.c +++ b/drivers/i2c/busses/i2c-thunderx-pcidrv.c @@ -208,6 +208,7 @@ static int thunder_i2c_probe_pci(struct pci_dev *pdev, i2c->adap.bus_recovery_info = &octeon_i2c_recovery_info; i2c->adap.dev.parent = dev; i2c->adap.dev.of_node = pdev->dev.of_node; + i2c->adap.dev.fwnode = dev->fwnode; snprintf(i2c->adap.name, sizeof(i2c->adap.name), "Cavium ThunderX i2c adapter at %s", dev_name(dev)); i2c_set_adapdata(&i2c->adap, i2c);
linux-stable-mirror@lists.linaro.org
-
Sasha Levin