On Fri, 13 Mar 2020 at 06:41, Sowjanya Komatineni skomatineni@nvidia.com wrote:
Tegra host supports HW busy detection and timeouts based on the count programmed in SDHCI_TIMEOUT_CONTROL register and max busy timeout it supports is 11s in finite busy wait mode.
Some operations like SLEEP_AWAKE, ERASE and flush cache through SWITCH commands take longer than 11s and Tegra host supports infinite HW busy wait mode where HW waits forever till the card is busy without HW timeout.
This patch implements Tegra specific set_timeout sdhci_ops to allow switching between finite and infinite HW busy detection wait modes based on the device command expected operation time.
Signed-off-by: Sowjanya Komatineni skomatineni@nvidia.com
drivers/mmc/host/sdhci-tegra.c | 31 +++++++++++++++++++++++++++++++ 1 file changed, 31 insertions(+)
diff --git a/drivers/mmc/host/sdhci-tegra.c b/drivers/mmc/host/sdhci-tegra.c index a25c3a4..fa8f6a4 100644 --- a/drivers/mmc/host/sdhci-tegra.c +++ b/drivers/mmc/host/sdhci-tegra.c @@ -45,6 +45,7 @@ #define SDHCI_TEGRA_CAP_OVERRIDES_DQS_TRIM_SHIFT 8
#define SDHCI_TEGRA_VENDOR_MISC_CTRL 0x120 +#define SDHCI_MISC_CTRL_ERASE_TIMEOUT_LIMIT BIT(0) #define SDHCI_MISC_CTRL_ENABLE_SDR104 0x8
#define SDHCI_MISC_CTRL_ENABLE_SDR50 0x10 #define SDHCI_MISC_CTRL_ENABLE_SDHCI_SPEC_300 0x20 @@ -1227,6 +1228,34 @@ static u32 sdhci_tegra_cqhci_irq(struct sdhci_host *host, u32 intmask) return 0; }
+static void tegra_sdhci_set_timeout(struct sdhci_host *host,
struct mmc_command *cmd)+{
u32 val;/** HW busy detection timeout is based on programmed data timeout* counter and maximum supported timeout is 11s which may not be* enough for long operations like cache flush, sleep awake, erase.** ERASE_TIMEOUT_LIMIT bit of VENDOR_MISC_CTRL register allows* host controller to wait for busy state until the card is busy* without HW timeout.** So, use infinite busy wait mode for operations that may take* more than maximum HW busy timeout of 11s otherwise use finite* busy wait mode.*/val = sdhci_readl(host, SDHCI_TEGRA_VENDOR_MISC_CTRL);if (cmd && cmd->busy_timeout >= 11 * HZ)val |= SDHCI_MISC_CTRL_ERASE_TIMEOUT_LIMIT;elseval &= ~SDHCI_MISC_CTRL_ERASE_TIMEOUT_LIMIT;sdhci_writel(host, val, SDHCI_TEGRA_VENDOR_MISC_CTRL);__sdhci_set_timeout(host, cmd);
kernel build on arm and arm64 architecture failed on stable-rc 4.19 (arm), 5.4 (arm64) and 5.5 (arm64)
drivers/mmc/host/sdhci-tegra.c: In function 'tegra_sdhci_set_timeout': drivers/mmc/host/sdhci-tegra.c:1256:2: error: implicit declaration of function '__sdhci_set_timeout'; did you mean 'tegra_sdhci_set_timeout'? [-Werror=implicit-function-declaration] __sdhci_set_timeout(host, cmd); ^~~~~~~~~~~~~~~~~~~ tegra_sdhci_set_timeout
Full build log, https://ci.linaro.org/view/lkft/job/openembedded-lkft-linux-stable-rc-5.5/DI... https://ci.linaro.org/view/lkft/job/openembedded-lkft-linux-stable-rc-5.4/DI... https://ci.linaro.org/view/lkft/job/openembedded-lkft-linux-stable-rc-4.19/D...
- Naresh
On Wed, 15 Apr 2020 at 19:55, Naresh Kamboju naresh.kamboju@linaro.org wrote:
On Fri, 13 Mar 2020 at 06:41, Sowjanya Komatineni skomatineni@nvidia.com wrote:
Tegra host supports HW busy detection and timeouts based on the count programmed in SDHCI_TIMEOUT_CONTROL register and max busy timeout it supports is 11s in finite busy wait mode.
Some operations like SLEEP_AWAKE, ERASE and flush cache through SWITCH commands take longer than 11s and Tegra host supports infinite HW busy wait mode where HW waits forever till the card is busy without HW timeout.
This patch implements Tegra specific set_timeout sdhci_ops to allow switching between finite and infinite HW busy detection wait modes based on the device command expected operation time.
Signed-off-by: Sowjanya Komatineni skomatineni@nvidia.com
drivers/mmc/host/sdhci-tegra.c | 31 +++++++++++++++++++++++++++++++ 1 file changed, 31 insertions(+)
diff --git a/drivers/mmc/host/sdhci-tegra.c b/drivers/mmc/host/sdhci-tegra.c index a25c3a4..fa8f6a4 100644 --- a/drivers/mmc/host/sdhci-tegra.c +++ b/drivers/mmc/host/sdhci-tegra.c @@ -45,6 +45,7 @@ #define SDHCI_TEGRA_CAP_OVERRIDES_DQS_TRIM_SHIFT 8
#define SDHCI_TEGRA_VENDOR_MISC_CTRL 0x120 +#define SDHCI_MISC_CTRL_ERASE_TIMEOUT_LIMIT BIT(0) #define SDHCI_MISC_CTRL_ENABLE_SDR104 0x8
#define SDHCI_MISC_CTRL_ENABLE_SDR50 0x10 #define SDHCI_MISC_CTRL_ENABLE_SDHCI_SPEC_300 0x20 @@ -1227,6 +1228,34 @@ static u32 sdhci_tegra_cqhci_irq(struct sdhci_host *host, u32 intmask) return 0; }
+static void tegra_sdhci_set_timeout(struct sdhci_host *host,
struct mmc_command *cmd)+{
u32 val;/** HW busy detection timeout is based on programmed data timeout* counter and maximum supported timeout is 11s which may not be* enough for long operations like cache flush, sleep awake, erase.** ERASE_TIMEOUT_LIMIT bit of VENDOR_MISC_CTRL register allows* host controller to wait for busy state until the card is busy* without HW timeout.** So, use infinite busy wait mode for operations that may take* more than maximum HW busy timeout of 11s otherwise use finite* busy wait mode.*/val = sdhci_readl(host, SDHCI_TEGRA_VENDOR_MISC_CTRL);if (cmd && cmd->busy_timeout >= 11 * HZ)val |= SDHCI_MISC_CTRL_ERASE_TIMEOUT_LIMIT;elseval &= ~SDHCI_MISC_CTRL_ERASE_TIMEOUT_LIMIT;sdhci_writel(host, val, SDHCI_TEGRA_VENDOR_MISC_CTRL);__sdhci_set_timeout(host, cmd);kernel build on arm and arm64 architecture failed on stable-rc 4.19 (arm), 5.4 (arm64) and 5.5 (arm64)
drivers/mmc/host/sdhci-tegra.c: In function 'tegra_sdhci_set_timeout': drivers/mmc/host/sdhci-tegra.c:1256:2: error: implicit declaration of function '__sdhci_set_timeout'; did you mean 'tegra_sdhci_set_timeout'? [-Werror=implicit-function-declaration] __sdhci_set_timeout(host, cmd); ^~~~~~~~~~~~~~~~~~~ tegra_sdhci_set_timeout
Full build log, https://ci.linaro.org/view/lkft/job/openembedded-lkft-linux-stable-rc-5.5/DI... https://ci.linaro.org/view/lkft/job/openembedded-lkft-linux-stable-rc-5.4/DI... https://ci.linaro.org/view/lkft/job/openembedded-lkft-linux-stable-rc-4.19/D...
- Naresh
Thanks for reporting! What a mess.
It turns out that the commit that was queued for stable that is causing the above errors, also requires another commit.
The commit that was queued: 5e958e4aacf4 ("sdhci: tegra: Implement Tegra specific set_timeout callback")
The additional commit needed (which was added in v5.6-rc1): 7d76ed77cfbd ("mmc: sdhci: Refactor sdhci_set_timeout()")
However, the above commit needs a manual backport (quite trivial, but still) for the relevant stable kernels, to allow it to solve the build problems.
Greg, Sasha - I suggest you to drop the offending commit from the stable kernels, for now. I think it's better to let Sowjanya deal with the backports, then send them in small series instead.
Kind regards Uffe
On Thu, Apr 16, 2020 at 12:59:06PM +0200, Ulf Hansson wrote:
On Wed, 15 Apr 2020 at 19:55, Naresh Kamboju naresh.kamboju@linaro.org wrote:
On Fri, 13 Mar 2020 at 06:41, Sowjanya Komatineni skomatineni@nvidia.com wrote:
Tegra host supports HW busy detection and timeouts based on the count programmed in SDHCI_TIMEOUT_CONTROL register and max busy timeout it supports is 11s in finite busy wait mode.
Some operations like SLEEP_AWAKE, ERASE and flush cache through SWITCH commands take longer than 11s and Tegra host supports infinite HW busy wait mode where HW waits forever till the card is busy without HW timeout.
This patch implements Tegra specific set_timeout sdhci_ops to allow switching between finite and infinite HW busy detection wait modes based on the device command expected operation time.
Signed-off-by: Sowjanya Komatineni skomatineni@nvidia.com
drivers/mmc/host/sdhci-tegra.c | 31 +++++++++++++++++++++++++++++++ 1 file changed, 31 insertions(+)
diff --git a/drivers/mmc/host/sdhci-tegra.c b/drivers/mmc/host/sdhci-tegra.c index a25c3a4..fa8f6a4 100644 --- a/drivers/mmc/host/sdhci-tegra.c +++ b/drivers/mmc/host/sdhci-tegra.c @@ -45,6 +45,7 @@ #define SDHCI_TEGRA_CAP_OVERRIDES_DQS_TRIM_SHIFT 8
#define SDHCI_TEGRA_VENDOR_MISC_CTRL 0x120 +#define SDHCI_MISC_CTRL_ERASE_TIMEOUT_LIMIT BIT(0) #define SDHCI_MISC_CTRL_ENABLE_SDR104 0x8
#define SDHCI_MISC_CTRL_ENABLE_SDR50 0x10 #define SDHCI_MISC_CTRL_ENABLE_SDHCI_SPEC_300 0x20 @@ -1227,6 +1228,34 @@ static u32 sdhci_tegra_cqhci_irq(struct sdhci_host *host, u32 intmask) return 0; }
+static void tegra_sdhci_set_timeout(struct sdhci_host *host,
struct mmc_command *cmd)+{
u32 val;/** HW busy detection timeout is based on programmed data timeout* counter and maximum supported timeout is 11s which may not be* enough for long operations like cache flush, sleep awake, erase.** ERASE_TIMEOUT_LIMIT bit of VENDOR_MISC_CTRL register allows* host controller to wait for busy state until the card is busy* without HW timeout.** So, use infinite busy wait mode for operations that may take* more than maximum HW busy timeout of 11s otherwise use finite* busy wait mode.*/val = sdhci_readl(host, SDHCI_TEGRA_VENDOR_MISC_CTRL);if (cmd && cmd->busy_timeout >= 11 * HZ)val |= SDHCI_MISC_CTRL_ERASE_TIMEOUT_LIMIT;elseval &= ~SDHCI_MISC_CTRL_ERASE_TIMEOUT_LIMIT;sdhci_writel(host, val, SDHCI_TEGRA_VENDOR_MISC_CTRL);__sdhci_set_timeout(host, cmd);kernel build on arm and arm64 architecture failed on stable-rc 4.19 (arm), 5.4 (arm64) and 5.5 (arm64)
drivers/mmc/host/sdhci-tegra.c: In function 'tegra_sdhci_set_timeout': drivers/mmc/host/sdhci-tegra.c:1256:2: error: implicit declaration of function '__sdhci_set_timeout'; did you mean 'tegra_sdhci_set_timeout'? [-Werror=implicit-function-declaration] __sdhci_set_timeout(host, cmd); ^~~~~~~~~~~~~~~~~~~ tegra_sdhci_set_timeout
Full build log, https://ci.linaro.org/view/lkft/job/openembedded-lkft-linux-stable-rc-5.5/DI... https://ci.linaro.org/view/lkft/job/openembedded-lkft-linux-stable-rc-5.4/DI... https://ci.linaro.org/view/lkft/job/openembedded-lkft-linux-stable-rc-4.19/D...
- Naresh
Thanks for reporting! What a mess.
It turns out that the commit that was queued for stable that is causing the above errors, also requires another commit.
The commit that was queued: 5e958e4aacf4 ("sdhci: tegra: Implement Tegra specific set_timeout callback")
The additional commit needed (which was added in v5.6-rc1): 7d76ed77cfbd ("mmc: sdhci: Refactor sdhci_set_timeout()")
However, the above commit needs a manual backport (quite trivial, but still) for the relevant stable kernels, to allow it to solve the build problems.
Greg, Sasha - I suggest you to drop the offending commit from the stable kernels, for now. I think it's better to let Sowjanya deal with the backports, then send them in small series instead.
Thanks for this, now dropped.
greg k-h
On 4/16/20 3:59 AM, Ulf Hansson wrote:
External email: Use caution opening links or attachments
On Wed, 15 Apr 2020 at 19:55, Naresh Kamboju naresh.kamboju@linaro.org wrote:
On Fri, 13 Mar 2020 at 06:41, Sowjanya Komatineni skomatineni@nvidia.com wrote:
Tegra host supports HW busy detection and timeouts based on the count programmed in SDHCI_TIMEOUT_CONTROL register and max busy timeout it supports is 11s in finite busy wait mode.
Some operations like SLEEP_AWAKE, ERASE and flush cache through SWITCH commands take longer than 11s and Tegra host supports infinite HW busy wait mode where HW waits forever till the card is busy without HW timeout.
This patch implements Tegra specific set_timeout sdhci_ops to allow switching between finite and infinite HW busy detection wait modes based on the device command expected operation time.
Signed-off-by: Sowjanya Komatineni skomatineni@nvidia.com
drivers/mmc/host/sdhci-tegra.c | 31 +++++++++++++++++++++++++++++++ 1 file changed, 31 insertions(+)
diff --git a/drivers/mmc/host/sdhci-tegra.c b/drivers/mmc/host/sdhci-tegra.c index a25c3a4..fa8f6a4 100644 --- a/drivers/mmc/host/sdhci-tegra.c +++ b/drivers/mmc/host/sdhci-tegra.c @@ -45,6 +45,7 @@ #define SDHCI_TEGRA_CAP_OVERRIDES_DQS_TRIM_SHIFT 8
#define SDHCI_TEGRA_VENDOR_MISC_CTRL 0x120 +#define SDHCI_MISC_CTRL_ERASE_TIMEOUT_LIMIT BIT(0) #define SDHCI_MISC_CTRL_ENABLE_SDR104 0x8 #define SDHCI_MISC_CTRL_ENABLE_SDR50 0x10 #define SDHCI_MISC_CTRL_ENABLE_SDHCI_SPEC_300 0x20 @@ -1227,6 +1228,34 @@ static u32 sdhci_tegra_cqhci_irq(struct sdhci_host *host, u32 intmask) return 0; }
+static void tegra_sdhci_set_timeout(struct sdhci_host *host,
struct mmc_command *cmd)+{
u32 val;/** HW busy detection timeout is based on programmed data timeout* counter and maximum supported timeout is 11s which may not be* enough for long operations like cache flush, sleep awake, erase.** ERASE_TIMEOUT_LIMIT bit of VENDOR_MISC_CTRL register allows* host controller to wait for busy state until the card is busy* without HW timeout.** So, use infinite busy wait mode for operations that may take* more than maximum HW busy timeout of 11s otherwise use finite* busy wait mode.*/val = sdhci_readl(host, SDHCI_TEGRA_VENDOR_MISC_CTRL);if (cmd && cmd->busy_timeout >= 11 * HZ)val |= SDHCI_MISC_CTRL_ERASE_TIMEOUT_LIMIT;elseval &= ~SDHCI_MISC_CTRL_ERASE_TIMEOUT_LIMIT;sdhci_writel(host, val, SDHCI_TEGRA_VENDOR_MISC_CTRL);__sdhci_set_timeout(host, cmd);kernel build on arm and arm64 architecture failed on stable-rc 4.19 (arm), 5.4 (arm64) and 5.5 (arm64)
drivers/mmc/host/sdhci-tegra.c: In function 'tegra_sdhci_set_timeout': drivers/mmc/host/sdhci-tegra.c:1256:2: error: implicit declaration of function '__sdhci_set_timeout'; did you mean 'tegra_sdhci_set_timeout'? [-Werror=implicit-function-declaration] __sdhci_set_timeout(host, cmd); ^~~~~~~~~~~~~~~~~~~ tegra_sdhci_set_timeout
Full build log, https://ci.linaro.org/view/lkft/job/openembedded-lkft-linux-stable-rc-5.5/DI... https://ci.linaro.org/view/lkft/job/openembedded-lkft-linux-stable-rc-5.4/DI... https://ci.linaro.org/view/lkft/job/openembedded-lkft-linux-stable-rc-4.19/D...
- Naresh
Thanks for reporting! What a mess.
It turns out that the commit that was queued for stable that is causing the above errors, also requires another commit.
The commit that was queued: 5e958e4aacf4 ("sdhci: tegra: Implement Tegra specific set_timeout callback")
The additional commit needed (which was added in v5.6-rc1): 7d76ed77cfbd ("mmc: sdhci: Refactor sdhci_set_timeout()")
However, the above commit needs a manual backport (quite trivial, but still) for the relevant stable kernels, to allow it to solve the build problems.
Greg, Sasha - I suggest you to drop the offending commit from the stable kernels, for now. I think it's better to let Sowjanya deal with the backports, then send them in small series instead.
Kind regards Uffe
Hi Ufee,
Will back-porting below commit cause any issues to other vendors?
7d76ed77cfbd ("mmc: sdhci: Refactor sdhci_set_timeout()")
Thanks Sowjanya
On 4/16/20 9:29 AM, Sowjanya Komatineni wrote:
On 4/16/20 3:59 AM, Ulf Hansson wrote:
External email: Use caution opening links or attachments
On Wed, 15 Apr 2020 at 19:55, Naresh Kamboju naresh.kamboju@linaro.org wrote:
On Fri, 13 Mar 2020 at 06:41, Sowjanya Komatineni skomatineni@nvidia.com wrote:
Tegra host supports HW busy detection and timeouts based on the count programmed in SDHCI_TIMEOUT_CONTROL register and max busy timeout it supports is 11s in finite busy wait mode.
Some operations like SLEEP_AWAKE, ERASE and flush cache through SWITCH commands take longer than 11s and Tegra host supports infinite HW busy wait mode where HW waits forever till the card is busy without HW timeout.
This patch implements Tegra specific set_timeout sdhci_ops to allow switching between finite and infinite HW busy detection wait modes based on the device command expected operation time.
Signed-off-by: Sowjanya Komatineni skomatineni@nvidia.com
drivers/mmc/host/sdhci-tegra.c | 31 +++++++++++++++++++++++++++++++ 1 file changed, 31 insertions(+)
diff --git a/drivers/mmc/host/sdhci-tegra.c b/drivers/mmc/host/sdhci-tegra.c index a25c3a4..fa8f6a4 100644 --- a/drivers/mmc/host/sdhci-tegra.c +++ b/drivers/mmc/host/sdhci-tegra.c @@ -45,6 +45,7 @@ #define SDHCI_TEGRA_CAP_OVERRIDES_DQS_TRIM_SHIFT 8
#define SDHCI_TEGRA_VENDOR_MISC_CTRL 0x120 +#define SDHCI_MISC_CTRL_ERASE_TIMEOUT_LIMIT BIT(0) #define SDHCI_MISC_CTRL_ENABLE_SDR104 0x8 #define SDHCI_MISC_CTRL_ENABLE_SDR50 0x10 #define SDHCI_MISC_CTRL_ENABLE_SDHCI_SPEC_300 0x20 @@ -1227,6 +1228,34 @@ static u32 sdhci_tegra_cqhci_irq(struct sdhci_host *host, u32 intmask) return 0; }
+static void tegra_sdhci_set_timeout(struct sdhci_host *host, + struct mmc_command *cmd) +{ + u32 val;
+ /* + * HW busy detection timeout is based on programmed data timeout + * counter and maximum supported timeout is 11s which may not be + * enough for long operations like cache flush, sleep awake, erase. + * + * ERASE_TIMEOUT_LIMIT bit of VENDOR_MISC_CTRL register allows + * host controller to wait for busy state until the card is busy + * without HW timeout. + * + * So, use infinite busy wait mode for operations that may take + * more than maximum HW busy timeout of 11s otherwise use finite + * busy wait mode. + */ + val = sdhci_readl(host, SDHCI_TEGRA_VENDOR_MISC_CTRL); + if (cmd && cmd->busy_timeout >= 11 * HZ) + val |= SDHCI_MISC_CTRL_ERASE_TIMEOUT_LIMIT; + else + val &= ~SDHCI_MISC_CTRL_ERASE_TIMEOUT_LIMIT; + sdhci_writel(host, val, SDHCI_TEGRA_VENDOR_MISC_CTRL);
+ __sdhci_set_timeout(host, cmd);
kernel build on arm and arm64 architecture failed on stable-rc 4.19 (arm), 5.4 (arm64) and 5.5 (arm64)
drivers/mmc/host/sdhci-tegra.c: In function 'tegra_sdhci_set_timeout': drivers/mmc/host/sdhci-tegra.c:1256:2: error: implicit declaration of function '__sdhci_set_timeout'; did you mean 'tegra_sdhci_set_timeout'? [-Werror=implicit-function-declaration] __sdhci_set_timeout(host, cmd); ^~~~~~~~~~~~~~~~~~~ tegra_sdhci_set_timeout
Full build log, https://ci.linaro.org/view/lkft/job/openembedded-lkft-linux-stable-rc-5.5/DI...
https://ci.linaro.org/view/lkft/job/openembedded-lkft-linux-stable-rc-5.4/DI...
https://ci.linaro.org/view/lkft/job/openembedded-lkft-linux-stable-rc-4.19/D...
- Naresh
Thanks for reporting! What a mess.
It turns out that the commit that was queued for stable that is causing the above errors, also requires another commit.
The commit that was queued: 5e958e4aacf4 ("sdhci: tegra: Implement Tegra specific set_timeout callback")
The additional commit needed (which was added in v5.6-rc1): 7d76ed77cfbd ("mmc: sdhci: Refactor sdhci_set_timeout()")
However, the above commit needs a manual backport (quite trivial, but still) for the relevant stable kernels, to allow it to solve the build problems.
Greg, Sasha - I suggest you to drop the offending commit from the stable kernels, for now. I think it's better to let Sowjanya deal with the backports, then send them in small series instead.
Kind regards Uffe
Hi Ufee,
Will back-porting below commit cause any issues to other vendors?
7d76ed77cfbd ("mmc: sdhci: Refactor sdhci_set_timeout()")
sdhci-tegra driver in 4.19 is using same sdhci_ops for Tegra114 and Tegra210 and separate sdhci_ops for T210 started from 4.20.
5e958e4aacf4 ("sdhci: tegra: Implement Tegra specific set_timeout callback")
So above commit can't be applied to 4.19. So probably a separate patch need to be created to apply for 4.19 and back port above commit along with its dependency commit (7d76ed77cfbd ("mmc: sdhci: Refactor sdhci_set_timeout()") for 5.4 and 5.4.
Thanks
Sowjanya
On Thu, 16 Apr 2020 at 21:39, Sowjanya Komatineni skomatineni@nvidia.com wrote:
On 4/16/20 9:29 AM, Sowjanya Komatineni wrote:
On 4/16/20 3:59 AM, Ulf Hansson wrote:
External email: Use caution opening links or attachments
On Wed, 15 Apr 2020 at 19:55, Naresh Kamboju naresh.kamboju@linaro.org wrote:
On Fri, 13 Mar 2020 at 06:41, Sowjanya Komatineni skomatineni@nvidia.com wrote:
Tegra host supports HW busy detection and timeouts based on the count programmed in SDHCI_TIMEOUT_CONTROL register and max busy timeout it supports is 11s in finite busy wait mode.
Some operations like SLEEP_AWAKE, ERASE and flush cache through SWITCH commands take longer than 11s and Tegra host supports infinite HW busy wait mode where HW waits forever till the card is busy without HW timeout.
This patch implements Tegra specific set_timeout sdhci_ops to allow switching between finite and infinite HW busy detection wait modes based on the device command expected operation time.
Signed-off-by: Sowjanya Komatineni skomatineni@nvidia.com
drivers/mmc/host/sdhci-tegra.c | 31 +++++++++++++++++++++++++++++++ 1 file changed, 31 insertions(+)
diff --git a/drivers/mmc/host/sdhci-tegra.c b/drivers/mmc/host/sdhci-tegra.c index a25c3a4..fa8f6a4 100644 --- a/drivers/mmc/host/sdhci-tegra.c +++ b/drivers/mmc/host/sdhci-tegra.c @@ -45,6 +45,7 @@ #define SDHCI_TEGRA_CAP_OVERRIDES_DQS_TRIM_SHIFT 8
#define SDHCI_TEGRA_VENDOR_MISC_CTRL 0x120 +#define SDHCI_MISC_CTRL_ERASE_TIMEOUT_LIMIT BIT(0) #define SDHCI_MISC_CTRL_ENABLE_SDR104 0x8 #define SDHCI_MISC_CTRL_ENABLE_SDR50 0x10 #define SDHCI_MISC_CTRL_ENABLE_SDHCI_SPEC_300 0x20 @@ -1227,6 +1228,34 @@ static u32 sdhci_tegra_cqhci_irq(struct sdhci_host *host, u32 intmask) return 0; }
+static void tegra_sdhci_set_timeout(struct sdhci_host *host,
struct mmc_command *cmd)+{
u32 val;/** HW busy detection timeout is based on programmed datatimeout
* counter and maximum supported timeout is 11s which maynot be
* enough for long operations like cache flush, sleepawake, erase.
** ERASE_TIMEOUT_LIMIT bit of VENDOR_MISC_CTRL register allows* host controller to wait for busy state until the card isbusy
* without HW timeout.** So, use infinite busy wait mode for operations that maytake
* more than maximum HW busy timeout of 11s otherwise usefinite
* busy wait mode.*/val = sdhci_readl(host, SDHCI_TEGRA_VENDOR_MISC_CTRL);if (cmd && cmd->busy_timeout >= 11 * HZ)val |= SDHCI_MISC_CTRL_ERASE_TIMEOUT_LIMIT;elseval &= ~SDHCI_MISC_CTRL_ERASE_TIMEOUT_LIMIT;sdhci_writel(host, val, SDHCI_TEGRA_VENDOR_MISC_CTRL);__sdhci_set_timeout(host, cmd);kernel build on arm and arm64 architecture failed on stable-rc 4.19 (arm), 5.4 (arm64) and 5.5 (arm64)
drivers/mmc/host/sdhci-tegra.c: In function 'tegra_sdhci_set_timeout': drivers/mmc/host/sdhci-tegra.c:1256:2: error: implicit declaration of function '__sdhci_set_timeout'; did you mean 'tegra_sdhci_set_timeout'? [-Werror=implicit-function-declaration] __sdhci_set_timeout(host, cmd); ^~~~~~~~~~~~~~~~~~~ tegra_sdhci_set_timeout
Full build log, https://ci.linaro.org/view/lkft/job/openembedded-lkft-linux-stable-rc-5.5/DI...
https://ci.linaro.org/view/lkft/job/openembedded-lkft-linux-stable-rc-5.4/DI...
https://ci.linaro.org/view/lkft/job/openembedded-lkft-linux-stable-rc-4.19/D...
- Naresh
Thanks for reporting! What a mess.
It turns out that the commit that was queued for stable that is causing the above errors, also requires another commit.
The commit that was queued: 5e958e4aacf4 ("sdhci: tegra: Implement Tegra specific set_timeout callback")
The additional commit needed (which was added in v5.6-rc1): 7d76ed77cfbd ("mmc: sdhci: Refactor sdhci_set_timeout()")
However, the above commit needs a manual backport (quite trivial, but still) for the relevant stable kernels, to allow it to solve the build problems.
Greg, Sasha - I suggest you to drop the offending commit from the stable kernels, for now. I think it's better to let Sowjanya deal with the backports, then send them in small series instead.
Kind regards Uffe
Hi Ufee,
Will back-porting below commit cause any issues to other vendors?
7d76ed77cfbd ("mmc: sdhci: Refactor sdhci_set_timeout()")
sdhci-tegra driver in 4.19 is using same sdhci_ops for Tegra114 and Tegra210 and separate sdhci_ops for T210 started from 4.20.
5e958e4aacf4 ("sdhci: tegra: Implement Tegra specific set_timeout callback")
So above commit can't be applied to 4.19. So probably a separate patch need to be created to apply for 4.19 and back port above commit along with its dependency commit (7d76ed77cfbd ("mmc: sdhci: Refactor sdhci_set_timeout()") for 5.4 and 5.4.
Alright, seems reasonable. Just keep me/Adrian on cc when/if you post the patches so we can ack them.
Kind regards Uffe
On 4/17/20 1:04 AM, Ulf Hansson wrote:
External email: Use caution opening links or attachments
On Thu, 16 Apr 2020 at 21:39, Sowjanya Komatineni skomatineni@nvidia.com wrote:
On 4/16/20 9:29 AM, Sowjanya Komatineni wrote:
On 4/16/20 3:59 AM, Ulf Hansson wrote:
External email: Use caution opening links or attachments
On Wed, 15 Apr 2020 at 19:55, Naresh Kamboju naresh.kamboju@linaro.org wrote:
On Fri, 13 Mar 2020 at 06:41, Sowjanya Komatineni skomatineni@nvidia.com wrote:
Tegra host supports HW busy detection and timeouts based on the count programmed in SDHCI_TIMEOUT_CONTROL register and max busy timeout it supports is 11s in finite busy wait mode.
Some operations like SLEEP_AWAKE, ERASE and flush cache through SWITCH commands take longer than 11s and Tegra host supports infinite HW busy wait mode where HW waits forever till the card is busy without HW timeout.
This patch implements Tegra specific set_timeout sdhci_ops to allow switching between finite and infinite HW busy detection wait modes based on the device command expected operation time.
Signed-off-by: Sowjanya Komatineni skomatineni@nvidia.com
drivers/mmc/host/sdhci-tegra.c | 31 +++++++++++++++++++++++++++++++ 1 file changed, 31 insertions(+)
diff --git a/drivers/mmc/host/sdhci-tegra.c b/drivers/mmc/host/sdhci-tegra.c index a25c3a4..fa8f6a4 100644 --- a/drivers/mmc/host/sdhci-tegra.c +++ b/drivers/mmc/host/sdhci-tegra.c @@ -45,6 +45,7 @@ #define SDHCI_TEGRA_CAP_OVERRIDES_DQS_TRIM_SHIFT 8
#define SDHCI_TEGRA_VENDOR_MISC_CTRL 0x120 +#define SDHCI_MISC_CTRL_ERASE_TIMEOUT_LIMIT BIT(0) #define SDHCI_MISC_CTRL_ENABLE_SDR104 0x8 #define SDHCI_MISC_CTRL_ENABLE_SDR50 0x10 #define SDHCI_MISC_CTRL_ENABLE_SDHCI_SPEC_300 0x20 @@ -1227,6 +1228,34 @@ static u32 sdhci_tegra_cqhci_irq(struct sdhci_host *host, u32 intmask) return 0; }
+static void tegra_sdhci_set_timeout(struct sdhci_host *host,
struct mmc_command *cmd)+{
u32 val;/** HW busy detection timeout is based on programmed datatimeout
* counter and maximum supported timeout is 11s which maynot be
* enough for long operations like cache flush, sleepawake, erase.
** ERASE_TIMEOUT_LIMIT bit of VENDOR_MISC_CTRL register allows* host controller to wait for busy state until the card isbusy
* without HW timeout.** So, use infinite busy wait mode for operations that maytake
* more than maximum HW busy timeout of 11s otherwise usefinite
* busy wait mode.*/val = sdhci_readl(host, SDHCI_TEGRA_VENDOR_MISC_CTRL);if (cmd && cmd->busy_timeout >= 11 * HZ)val |= SDHCI_MISC_CTRL_ERASE_TIMEOUT_LIMIT;elseval &= ~SDHCI_MISC_CTRL_ERASE_TIMEOUT_LIMIT;sdhci_writel(host, val, SDHCI_TEGRA_VENDOR_MISC_CTRL);__sdhci_set_timeout(host, cmd);kernel build on arm and arm64 architecture failed on stable-rc 4.19 (arm), 5.4 (arm64) and 5.5 (arm64)
drivers/mmc/host/sdhci-tegra.c: In function 'tegra_sdhci_set_timeout': drivers/mmc/host/sdhci-tegra.c:1256:2: error: implicit declaration of function '__sdhci_set_timeout'; did you mean 'tegra_sdhci_set_timeout'? [-Werror=implicit-function-declaration] __sdhci_set_timeout(host, cmd); ^~~~~~~~~~~~~~~~~~~ tegra_sdhci_set_timeout
Full build log, https://ci.linaro.org/view/lkft/job/openembedded-lkft-linux-stable-rc-5.5/DI...
https://ci.linaro.org/view/lkft/job/openembedded-lkft-linux-stable-rc-5.4/DI...
https://ci.linaro.org/view/lkft/job/openembedded-lkft-linux-stable-rc-4.19/D...
- Naresh
Thanks for reporting! What a mess.
It turns out that the commit that was queued for stable that is causing the above errors, also requires another commit.
The commit that was queued: 5e958e4aacf4 ("sdhci: tegra: Implement Tegra specific set_timeout callback")
The additional commit needed (which was added in v5.6-rc1): 7d76ed77cfbd ("mmc: sdhci: Refactor sdhci_set_timeout()")
However, the above commit needs a manual backport (quite trivial, but still) for the relevant stable kernels, to allow it to solve the build problems.
Greg, Sasha - I suggest you to drop the offending commit from the stable kernels, for now. I think it's better to let Sowjanya deal with the backports, then send them in small series instead.
Kind regards Uffe
Hi Ufee,
Will back-porting below commit cause any issues to other vendors?
7d76ed77cfbd ("mmc: sdhci: Refactor sdhci_set_timeout()")
sdhci-tegra driver in 4.19 is using same sdhci_ops for Tegra114 and Tegra210 and separate sdhci_ops for T210 started from 4.20.
5e958e4aacf4 ("sdhci: tegra: Implement Tegra specific set_timeout callback")
So above commit can't be applied to 4.19. So probably a separate patch need to be created to apply for 4.19 and back port above commit along with its dependency commit (7d76ed77cfbd ("mmc: sdhci: Refactor sdhci_set_timeout()") for 5.4 and 5.4.
Alright, seems reasonable. Just keep me/Adrian on cc when/if you post the patches so we can ack them.
Kind regards Uffe
Sure, will send patches to backport both below changes to 4.19
5e958e4aacf4 ("sdhci: tegra: Implement Tegra specific set_timeout callback")
7d76ed77cfbd ("mmc: sdhci: Refactor sdhci_set_timeout()")
But on 5.5 and on 5.4.33, patch "mmc: sdhci: Refactor sdhci_set_timeout() already committed but not on 5.4.32 and prior.
So, not sure why kbuild reported error on 5.4 and 5.5 with __sdhci_set_timeout when this patch is already committed on 5.4.33 (26711cc7e064) and 5.5.18 (71bab39fa67d)
Can you please help clarify this?
drivers/mmc/host/sdhci-tegra.c: In function 'tegra_sdhci_set_timeout': drivers/mmc/host/sdhci-tegra.c:1256:2: error: implicit declaration of function '__sdhci_set_timeout'; did you mean 'tegra_sdhci_set_timeout'? [-Werror=implicit-function-declaration] __sdhci_set_timeout(host, cmd);
Thanks
Sowjanya
linux-stable-mirror@lists.linaro.org
-
Greg Kroah-Hartman -
Naresh Kamboju -
Sowjanya Komatineni -
Ulf Hansson