This is an automatic generated email to let you know that the following patch were queued:

Subject: media: pvrusb2: fix control-message timeouts Author: Johan Hovold johan@kernel.org Date: Mon Oct 25 13:16:39 2021 +0100

USB control-message timeouts are specified in milliseconds and should specifically not vary with CONFIG_HZ.

Fixes: d855497edbfb ("V4L/DVB (4228a): pvrusb2 to kernel 2.6.18") Cc: stable@vger.kernel.org # 2.6.18 Signed-off-by: Johan Hovold johan@kernel.org Signed-off-by: Hans Verkuil hverkuil-cisco@xs4all.nl Signed-off-by: Mauro Carvalho Chehab mchehab+huawei@kernel.org

drivers/media/usb/pvrusb2/pvrusb2-hdw.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-)

---

diff --git a/drivers/media/usb/pvrusb2/pvrusb2-hdw.c b/drivers/media/usb/pvrusb2/pvrusb2-hdw.c index d38dee1792e4..3915d551d59e 100644 --- a/drivers/media/usb/pvrusb2/pvrusb2-hdw.c +++ b/drivers/media/usb/pvrusb2/pvrusb2-hdw.c @@ -1467,7 +1467,7 @@ static int pvr2_upload_firmware1(struct pvr2_hdw *hdw) for (address = 0; address < fwsize; address += 0x800) { memcpy(fw_ptr, fw_entry->data + address, 0x800); ret += usb_control_msg(hdw->usb_dev, pipe, 0xa0, 0x40, address, - 0, fw_ptr, 0x800, HZ); + 0, fw_ptr, 0x800, 1000); }

trace_firmware("Upload done, releasing device's CPU"); @@ -1605,7 +1605,7 @@ int pvr2_upload_firmware2(struct pvr2_hdw *hdw) ((u32 *)fw_ptr)[icnt] = swab32(((u32 *)fw_ptr)[icnt]);

ret |= usb_bulk_msg(hdw->usb_dev, pipe, fw_ptr,bcnt, - &actual_length, HZ); + &actual_length, 1000); ret |= (actual_length != bcnt); if (ret) break; fw_done += bcnt; @@ -3438,7 +3438,7 @@ void pvr2_hdw_cpufw_set_enabled(struct pvr2_hdw *hdw, 0xa0,0xc0, address,0, hdw->fw_buffer+address, - 0x800,HZ); + 0x800,1000); if (ret < 0) break; }

@@ -3977,7 +3977,7 @@ void pvr2_hdw_cpureset_assert(struct pvr2_hdw *hdw,int val) /* Write the CPUCS register on the 8051. The lsb of the register is the reset bit; a 1 asserts reset while a 0 clears it. */ pipe = usb_sndctrlpipe(hdw->usb_dev, 0); - ret = usb_control_msg(hdw->usb_dev,pipe,0xa0,0x40,0xe600,0,da,1,HZ); + ret = usb_control_msg(hdw->usb_dev,pipe,0xa0,0x40,0xe600,0,da,1,1000); if (ret < 0) { pvr2_trace(PVR2_TRACE_ERROR_LEGS, "cpureset_assert(%d) error=%d",val,ret);