From: "Ji-Ze Hong (Peter Hong)" hpeter@gmail.com
[ Upstream commit 4aaaaf0f279836f06d3b9d0ffeec7a1e1a04ceef ]
All temperature of Fintek superio hwmonitor that using 1-byte reg will use 2's complement.
In show_temp() temp = data->temp[nr] * 1000;
When data->temp[nr] read as 255, it indicate -1C, but this code will report 255C to userspace. It'll be ok when change to: temp = ((s8)data->temp[nr]) * 1000;
Signed-off-by: Ji-Ze Hong (Peter Hong) hpeter+linux_kernel@gmail.com Link: https://lore.kernel.org/r/20220418090706.6339-1-hpeter+linux_kernel@gmail.co... Signed-off-by: Guenter Roeck linux@roeck-us.net Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/hwmon/f71882fg.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-)
diff --git a/drivers/hwmon/f71882fg.c b/drivers/hwmon/f71882fg.c index 4dec793fd07d..94b35723ee7a 100644 --- a/drivers/hwmon/f71882fg.c +++ b/drivers/hwmon/f71882fg.c @@ -1577,8 +1577,9 @@ static ssize_t show_temp(struct device *dev, struct device_attribute *devattr, temp *= 125; if (sign) temp -= 128000; - } else - temp = data->temp[nr] * 1000; + } else { + temp = ((s8)data->temp[nr]) * 1000; + }
return sprintf(buf, "%d\n", temp); }
From: Mark Brown broonie@kernel.org
[ Upstream commit 2fbe467bcbfc760a08f08475eea6bbd4c2874319 ]
The max98090 driver has a custom put function for some controls which can only be updated in certain circumstances which makes no effort to validate that input is suitable for the control, allowing out of spec values to be written to the hardware and presented to userspace. Fix this by returning an error when invalid values are written.
Signed-off-by: Mark Brown broonie@kernel.org Link: https://lore.kernel.org/r/20220420193454.2647908-1-broonie@kernel.org Signed-off-by: Mark Brown broonie@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- sound/soc/codecs/max98090.c | 3 +++ 1 file changed, 3 insertions(+)
diff --git a/sound/soc/codecs/max98090.c b/sound/soc/codecs/max98090.c index 945a79e4f3eb..779845e3a9e3 100644 --- a/sound/soc/codecs/max98090.c +++ b/sound/soc/codecs/max98090.c @@ -413,6 +413,9 @@ static int max98090_put_enab_tlv(struct snd_kcontrol *kcontrol,
val = (val >> mc->shift) & mask;
+ if (sel < 0 || sel > mc->max) + return -EINVAL; + *select = sel;
/* Setting a volume is only valid if it is already On */
From: Mark Brown broonie@kernel.org
[ Upstream commit 13fcf676d9e102594effc686d98521ff5c90b925 ]
The max98090 driver has some custom controls which share a put() function which returns 0 unconditionally, meaning that events are not generated when the value changes. Fix that.
Signed-off-by: Mark Brown broonie@kernel.org Link: https://lore.kernel.org/r/20220420193454.2647908-2-broonie@kernel.org Signed-off-by: Mark Brown broonie@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- sound/soc/codecs/max98090.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/sound/soc/codecs/max98090.c b/sound/soc/codecs/max98090.c index 779845e3a9e3..5b6405392f08 100644 --- a/sound/soc/codecs/max98090.c +++ b/sound/soc/codecs/max98090.c @@ -430,7 +430,7 @@ static int max98090_put_enab_tlv(struct snd_kcontrol *kcontrol, mask << mc->shift, sel << mc->shift);
- return 0; + return *select != val; }
static const char *max98090_perf_pwr_text[] =
From: Mark Brown broonie@kernel.org
[ Upstream commit aa22125c57f9e577f0a667e4fa07fc3fa8ca1e60 ]
Check that values written via snd_soc_put_volsw_range() are within the range advertised by the control, ensuring that we don't write out of spec values to the hardware.
Signed-off-by: Mark Brown broonie@kernel.org Link: https://lore.kernel.org/r/20220423131239.3375261-1-broonie@kernel.org Signed-off-by: Mark Brown broonie@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- sound/soc/soc-ops.c | 18 +++++++++++++++++- 1 file changed, 17 insertions(+), 1 deletion(-)
diff --git a/sound/soc/soc-ops.c b/sound/soc/soc-ops.c index 2bc9fa6a34b8..15bfcdbdfaa4 100644 --- a/sound/soc/soc-ops.c +++ b/sound/soc/soc-ops.c @@ -510,7 +510,15 @@ int snd_soc_put_volsw_range(struct snd_kcontrol *kcontrol, unsigned int mask = (1 << fls(max)) - 1; unsigned int invert = mc->invert; unsigned int val, val_mask; - int err, ret; + int err, ret, tmp; + + tmp = ucontrol->value.integer.value[0]; + if (tmp < 0) + return -EINVAL; + if (mc->platform_max && tmp > mc->platform_max) + return -EINVAL; + if (tmp > mc->max - mc->min + 1) + return -EINVAL;
if (invert) val = (max - ucontrol->value.integer.value[0]) & mask; @@ -525,6 +533,14 @@ int snd_soc_put_volsw_range(struct snd_kcontrol *kcontrol, ret = err;
if (snd_soc_volsw_is_stereo(mc)) { + tmp = ucontrol->value.integer.value[1]; + if (tmp < 0) + return -EINVAL; + if (mc->platform_max && tmp > mc->platform_max) + return -EINVAL; + if (tmp > mc->max - mc->min + 1) + return -EINVAL; + if (invert) val = (max - ucontrol->value.integer.value[1]) & mask; else
From: Sven Schnelle svens@linux.ibm.com
[ Upstream commit 8b202ee218395319aec1ef44f72043e1fbaccdd6 ]
gcc-12 shows a lot of array bound warnings on s390. This is caused by the S390_lowcore macro which uses a hardcoded address of 0.
Wrapping that with absolute_pointer() works, but gcc no longer knows that a 12 bit displacement is sufficient to access lowcore. So it emits instructions like 'lghi %r1,0; l %rx,xxx(%r1)' instead of a single load/store instruction. As s390 stores variables often read/written in lowcore, this is considered problematic. Therefore disable -Warray-bounds on s390 for gcc-12 for the time being, until there is a better solution.
Signed-off-by: Sven Schnelle svens@linux.ibm.com Link: https://lore.kernel.org/r/yt9dzgkelelc.fsf@linux.ibm.com Link: https://lore.kernel.org/r/20220422134308.1613610-1-svens@linux.ibm.com Link: https://lore.kernel.org/r/20220425121742.3222133-1-svens@linux.ibm.com Signed-off-by: Heiko Carstens hca@linux.ibm.com Signed-off-by: Sasha Levin sashal@kernel.org --- arch/s390/Makefile | 10 ++++++++++ 1 file changed, 10 insertions(+)
diff --git a/arch/s390/Makefile b/arch/s390/Makefile index 92506918da63..a8cb00f30a7c 100644 --- a/arch/s390/Makefile +++ b/arch/s390/Makefile @@ -32,6 +32,16 @@ KBUILD_CFLAGS_DECOMPRESSOR += -fno-stack-protector KBUILD_CFLAGS_DECOMPRESSOR += $(call cc-disable-warning, address-of-packed-member) KBUILD_CFLAGS_DECOMPRESSOR += $(if $(CONFIG_DEBUG_INFO),-g) KBUILD_CFLAGS_DECOMPRESSOR += $(if $(CONFIG_DEBUG_INFO_DWARF4), $(call cc-option, -gdwarf-4,)) + +ifdef CONFIG_CC_IS_GCC + ifeq ($(call cc-ifversion, -ge, 1200, y), y) + ifeq ($(call cc-ifversion, -lt, 1300, y), y) + KBUILD_CFLAGS += $(call cc-disable-warning, array-bounds) + KBUILD_CFLAGS_DECOMPRESSOR += $(call cc-disable-warning, array-bounds) + endif + endif +endif + UTS_MACHINE := s390x STACK_SIZE := $(if $(CONFIG_KASAN),65536,16384) CHECKFLAGS += -D__s390__ -D__s390x__
From: Shravya Kumbham shravya.kumbham@xilinx.com
[ Upstream commit b800528b97d0adc3a5ba42d78a8b0d3f07a31f44 ]
In xemaclite_open() function we are setting the max speed of emaclite to 100Mb using phy_set_max_speed() function so, there is no need to write the advertising registers to stop giga-bit speed and the phy_start() function starts the auto-negotiation so, there is no need to handle it separately using advertising registers. Remove the phy_read and phy_write of advertising registers in xemaclite_open() function.
Signed-off-by: Shravya Kumbham shravya.kumbham@xilinx.com Signed-off-by: Radhey Shyam Pandey radhey.shyam.pandey@xilinx.com Reviewed-by: Andrew Lunn andrew@lunn.ch Signed-off-by: Paolo Abeni pabeni@redhat.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/net/ethernet/xilinx/xilinx_emaclite.c | 15 --------------- 1 file changed, 15 deletions(-)
diff --git a/drivers/net/ethernet/xilinx/xilinx_emaclite.c b/drivers/net/ethernet/xilinx/xilinx_emaclite.c index 4bd44fbc6ecf..cc0335fceec5 100644 --- a/drivers/net/ethernet/xilinx/xilinx_emaclite.c +++ b/drivers/net/ethernet/xilinx/xilinx_emaclite.c @@ -923,8 +923,6 @@ static int xemaclite_open(struct net_device *dev) xemaclite_disable_interrupts(lp);
if (lp->phy_node) { - u32 bmcr; - lp->phy_dev = of_phy_connect(lp->ndev, lp->phy_node, xemaclite_adjust_link, 0, PHY_INTERFACE_MODE_MII); @@ -935,19 +933,6 @@ static int xemaclite_open(struct net_device *dev)
/* EmacLite doesn't support giga-bit speeds */ phy_set_max_speed(lp->phy_dev, SPEED_100); - - /* Don't advertise 1000BASE-T Full/Half duplex speeds */ - phy_write(lp->phy_dev, MII_CTRL1000, 0); - - /* Advertise only 10 and 100mbps full/half duplex speeds */ - phy_write(lp->phy_dev, MII_ADVERTISE, ADVERTISE_ALL | - ADVERTISE_CSMA); - - /* Restart auto negotiation */ - bmcr = phy_read(lp->phy_dev, MII_BMCR); - bmcr |= (BMCR_ANENABLE | BMCR_ANRESTART); - phy_write(lp->phy_dev, MII_BMCR, bmcr); - phy_start(lp->phy_dev); }
From: Matthew Hagan mnhagan88@gmail.com
[ Upstream commit 2069624dac19d62c558bb6468fe03678553ab01d ]
As noted elsewhere, various GPON SFP modules exhibit non-standard TX-fault behaviour. In the tested case, the Huawei MA5671A, when used in combination with a Marvell mv88e6085 switch, was found to persistently assert TX-fault, resulting in the module being disabled.
This patch adds a quirk to ignore the SFP_F_TX_FAULT state, allowing the module to function.
Change from v1: removal of erroneous return statment (Andrew Lunn)
Signed-off-by: Matthew Hagan mnhagan88@gmail.com Reviewed-by: Andrew Lunn andrew@lunn.ch Link: https://lore.kernel.org/r/20220502223315.1973376-1-mnhagan88@gmail.com Signed-off-by: Jakub Kicinski kuba@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/net/phy/sfp.c | 12 +++++++++++- 1 file changed, 11 insertions(+), 1 deletion(-)
diff --git a/drivers/net/phy/sfp.c b/drivers/net/phy/sfp.c index efffa65f8214..96068e0d841a 100644 --- a/drivers/net/phy/sfp.c +++ b/drivers/net/phy/sfp.c @@ -249,6 +249,7 @@ struct sfp { struct sfp_eeprom_id id; unsigned int module_power_mW; unsigned int module_t_start_up; + bool tx_fault_ignore;
#if IS_ENABLED(CONFIG_HWMON) struct sfp_diag diag; @@ -1893,6 +1894,12 @@ static int sfp_sm_mod_probe(struct sfp *sfp, bool report) else sfp->module_t_start_up = T_START_UP;
+ if (!memcmp(id.base.vendor_name, "HUAWEI ", 16) && + !memcmp(id.base.vendor_pn, "MA5671A ", 16)) + sfp->tx_fault_ignore = true; + else + sfp->tx_fault_ignore = false; + return 0; }
@@ -2320,7 +2327,10 @@ static void sfp_check_state(struct sfp *sfp) mutex_lock(&sfp->st_mutex); state = sfp_get_state(sfp); changed = state ^ sfp->state; - changed &= SFP_F_PRESENT | SFP_F_LOS | SFP_F_TX_FAULT; + if (sfp->tx_fault_ignore) + changed &= SFP_F_PRESENT | SFP_F_LOS; + else + changed &= SFP_F_PRESENT | SFP_F_LOS | SFP_F_TX_FAULT;
for (i = 0; i < GPIO_MAX; i++) if (changed & BIT(i))
From: Eric Dumazet edumazet@google.com
[ Upstream commit 4dfa9b438ee34caca4e6a4e5e961641807367f6f ]
In order to limit the ability for an observer to recognize the source ports sequence used to contact a set of destinations, we should periodically shuffle the secret. 10 seconds looks effective enough without causing particular issues.
Cc: Moshe Kol moshe.kol@mail.huji.ac.il Cc: Yossi Gilad yossi.gilad@mail.huji.ac.il Cc: Amit Klein aksecurity@gmail.com Cc: Jason A. Donenfeld Jason@zx2c4.com Tested-by: Willy Tarreau w@1wt.eu Signed-off-by: Eric Dumazet edumazet@google.com Signed-off-by: Jakub Kicinski kuba@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- net/core/secure_seq.c | 12 +++++++++--- 1 file changed, 9 insertions(+), 3 deletions(-)
diff --git a/net/core/secure_seq.c b/net/core/secure_seq.c index b5bc680d4755..b8a33c841846 100644 --- a/net/core/secure_seq.c +++ b/net/core/secure_seq.c @@ -22,6 +22,8 @@ static siphash_key_t net_secret __read_mostly; static siphash_key_t ts_secret __read_mostly;
+#define EPHEMERAL_PORT_SHUFFLE_PERIOD (10 * HZ) + static __always_inline void net_secret_init(void) { net_get_random_once(&net_secret, sizeof(net_secret)); @@ -100,11 +102,13 @@ u32 secure_ipv6_port_ephemeral(const __be32 *saddr, const __be32 *daddr, const struct { struct in6_addr saddr; struct in6_addr daddr; + unsigned int timeseed; __be16 dport; } __aligned(SIPHASH_ALIGNMENT) combined = { .saddr = *(struct in6_addr *)saddr, .daddr = *(struct in6_addr *)daddr, - .dport = dport + .timeseed = jiffies / EPHEMERAL_PORT_SHUFFLE_PERIOD, + .dport = dport, }; net_secret_init(); return siphash(&combined, offsetofend(typeof(combined), dport), @@ -145,8 +149,10 @@ EXPORT_SYMBOL_GPL(secure_tcp_seq); u32 secure_ipv4_port_ephemeral(__be32 saddr, __be32 daddr, __be16 dport) { net_secret_init(); - return siphash_3u32((__force u32)saddr, (__force u32)daddr, - (__force u16)dport, &net_secret); + return siphash_4u32((__force u32)saddr, (__force u32)daddr, + (__force u16)dport, + jiffies / EPHEMERAL_PORT_SHUFFLE_PERIOD, + &net_secret); } EXPORT_SYMBOL_GPL(secure_ipv4_port_ephemeral); #endif
From: Helge Deller deller@gmx.de
[ Upstream commit 6c800d7f55fcd78e17deae5ae4374d8e73482c13 ]
This reverts commit a9fe7fa7d874a536e0540469f314772c054a0323.
Leads to segfaults on 32bit kernel.
Signed-off-by: Helge Deller deller@gmx.de Signed-off-by: Sasha Levin sashal@kernel.org --- arch/parisc/kernel/patch.c | 25 ++++++++++++++----------- 1 file changed, 14 insertions(+), 11 deletions(-)
diff --git a/arch/parisc/kernel/patch.c b/arch/parisc/kernel/patch.c index e59574f65e64..80a0ab372802 100644 --- a/arch/parisc/kernel/patch.c +++ b/arch/parisc/kernel/patch.c @@ -40,7 +40,10 @@ static void __kprobes *patch_map(void *addr, int fixmap, unsigned long *flags,
*need_unmap = 1; set_fixmap(fixmap, page_to_phys(page)); - raw_spin_lock_irqsave(&patch_lock, *flags); + if (flags) + raw_spin_lock_irqsave(&patch_lock, *flags); + else + __acquire(&patch_lock);
return (void *) (__fix_to_virt(fixmap) + (uintaddr & ~PAGE_MASK)); } @@ -49,7 +52,10 @@ static void __kprobes patch_unmap(int fixmap, unsigned long *flags) { clear_fixmap(fixmap);
- raw_spin_unlock_irqrestore(&patch_lock, *flags); + if (flags) + raw_spin_unlock_irqrestore(&patch_lock, *flags); + else + __release(&patch_lock); }
void __kprobes __patch_text_multiple(void *addr, u32 *insn, unsigned int len) @@ -61,9 +67,8 @@ void __kprobes __patch_text_multiple(void *addr, u32 *insn, unsigned int len) int mapped;
/* Make sure we don't have any aliases in cache */ - flush_kernel_dcache_range_asm(start, end); - flush_kernel_icache_range_asm(start, end); - flush_tlb_kernel_range(start, end); + flush_kernel_vmap_range(addr, len); + flush_icache_range(start, end);
p = fixmap = patch_map(addr, FIX_TEXT_POKE0, &flags, &mapped);
@@ -76,10 +81,8 @@ void __kprobes __patch_text_multiple(void *addr, u32 *insn, unsigned int len) * We're crossing a page boundary, so * need to remap */ - flush_kernel_dcache_range_asm((unsigned long)fixmap, - (unsigned long)p); - flush_tlb_kernel_range((unsigned long)fixmap, - (unsigned long)p); + flush_kernel_vmap_range((void *)fixmap, + (p-fixmap) * sizeof(*p)); if (mapped) patch_unmap(FIX_TEXT_POKE0, &flags); p = fixmap = patch_map(addr, FIX_TEXT_POKE0, &flags, @@ -87,10 +90,10 @@ void __kprobes __patch_text_multiple(void *addr, u32 *insn, unsigned int len) } }
- flush_kernel_dcache_range_asm((unsigned long)fixmap, (unsigned long)p); - flush_tlb_kernel_range((unsigned long)fixmap, (unsigned long)p); + flush_kernel_vmap_range((void *)fixmap, (p-fixmap) * sizeof(*p)); if (mapped) patch_unmap(FIX_TEXT_POKE0, &flags); + flush_icache_range(start, end); }
void __kprobes __patch_text(void *addr, u32 insn)
linux-stable-mirror@lists.linaro.org
-
Sasha Levin