From: Phil Elwell phil@raspberrypi.com

[ Upstream commit 0a6380cb4c6b5c1d6dad226ba3130f9090f0ccea ]

If the RBUF logic is not reset when the kernel starts then there may be some data left over from any network boot loader. If the 64-byte packet headers are enabled then this can be fatal.

Extend bcmgenet_dma_disable to do perform the reset, but not when called from bcmgenet_resume in order to preserve a wake packet.

N.B. This different handling of resume is just based on a hunch - why else wouldn't one reset the RBUF as well as the TBUF? If this isn't the case then it's easy to change the patch to make the RBUF reset unconditional.

See: https://github.com/raspberrypi/linux/issues/3850 See: https://github.com/raspberrypi/firmware/issues/1882

Signed-off-by: Phil Elwell phil@raspberrypi.com Signed-off-by: Maarten Vanraes maarten@rmail.be Signed-off-by: David S. Miller davem@davemloft.net Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/net/ethernet/broadcom/genet/bcmgenet.c | 16 ++++++++++++---- 1 file changed, 12 insertions(+), 4 deletions(-)

diff --git a/drivers/net/ethernet/broadcom/genet/bcmgenet.c b/drivers/net/ethernet/broadcom/genet/bcmgenet.c index ed0589a1a00d8..b2309d2fbc2df 100644 --- a/drivers/net/ethernet/broadcom/genet/bcmgenet.c +++ b/drivers/net/ethernet/broadcom/genet/bcmgenet.c @@ -3252,7 +3252,7 @@ static void bcmgenet_get_hw_addr(struct bcmgenet_priv *priv, }

/* Returns a reusable dma control register value */ -static u32 bcmgenet_dma_disable(struct bcmgenet_priv *priv) +static u32 bcmgenet_dma_disable(struct bcmgenet_priv *priv, bool flush_rx) { unsigned int i; u32 reg; @@ -3277,6 +3277,14 @@ static u32 bcmgenet_dma_disable(struct bcmgenet_priv *priv) udelay(10); bcmgenet_umac_writel(priv, 0, UMAC_TX_FLUSH);

+ if (flush_rx) { + reg = bcmgenet_rbuf_ctrl_get(priv); + bcmgenet_rbuf_ctrl_set(priv, reg | BIT(0)); + udelay(10); + bcmgenet_rbuf_ctrl_set(priv, reg); + udelay(10); + } + return dma_ctrl; }

@@ -3340,8 +3348,8 @@ static int bcmgenet_open(struct net_device *dev)

bcmgenet_set_hw_addr(priv, dev->dev_addr);

- /* Disable RX/TX DMA and flush TX queues */ - dma_ctrl = bcmgenet_dma_disable(priv); + /* Disable RX/TX DMA and flush TX and RX queues */ + dma_ctrl = bcmgenet_dma_disable(priv, true);

/* Reinitialize TDMA and RDMA and SW housekeeping */ ret = bcmgenet_init_dma(priv); @@ -4199,7 +4207,7 @@ static int bcmgenet_resume(struct device *d) bcmgenet_hfb_create_rxnfc_filter(priv, rule);

/* Disable RX/TX DMA and flush TX queues */ - dma_ctrl = bcmgenet_dma_disable(priv); + dma_ctrl = bcmgenet_dma_disable(priv, false);

/* Reinitialize TDMA and RDMA and SW housekeeping */ ret = bcmgenet_init_dma(priv);

From: Adam Goldman adamg@pobox.com

[ Upstream commit 752e3c53de0fa3b7d817a83050b6699b8e9c6ec9 ]

In the FireWire OHCI interrupt handler, if a bus reset interrupt has occurred, mask bus reset interrupts until bus_reset_work has serviced and cleared the interrupt.

Normally, we always leave bus reset interrupts masked. We infer the bus reset from the self-ID interrupt that happens shortly thereafter. A scenario where we unmask bus reset interrupts was introduced in 2008 in a007bb857e0b26f5d8b73c2ff90782d9c0972620: If OHCI_PARAM_DEBUG_BUSRESETS (8) is set in the debug parameter bitmask, we will unmask bus reset interrupts so we can log them.

irq_handler logs the bus reset interrupt. However, we can't clear the bus reset event flag in irq_handler, because we won't service the event until later. irq_handler exits with the event flag still set. If the corresponding interrupt is still unmasked, the first bus reset will usually freeze the system due to irq_handler being called again each time it exits. This freeze can be reproduced by loading firewire_ohci with "modprobe firewire_ohci debug=-1" (to enable all debugging output). Apparently there are also some cases where bus_reset_work will get called soon enough to clear the event, and operation will continue normally.

This freeze was first reported a few months after a007bb85 was committed, but until now it was never fixed. The debug level could safely be set to -1 through sysfs after the module was loaded, but this would be ineffectual in logging bus reset interrupts since they were only unmasked during initialization.

irq_handler will now leave the event flag set but mask bus reset interrupts, so irq_handler won't be called again and there will be no freeze. If OHCI_PARAM_DEBUG_BUSRESETS is enabled, bus_reset_work will unmask the interrupt after servicing the event, so future interrupts will be caught as desired.

As a side effect to this change, OHCI_PARAM_DEBUG_BUSRESETS can now be enabled through sysfs in addition to during initial module loading. However, when enabled through sysfs, logging of bus reset interrupts will be effective only starting with the second bus reset, after bus_reset_work has executed.

Signed-off-by: Adam Goldman adamg@pobox.com Signed-off-by: Takashi Sakamoto o-takashi@sakamocchi.jp Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/firewire/ohci.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/drivers/firewire/ohci.c b/drivers/firewire/ohci.c index 45d19cc0aeac0..9b2471d12783c 100644 --- a/drivers/firewire/ohci.c +++ b/drivers/firewire/ohci.c @@ -2049,6 +2049,8 @@ static void bus_reset_work(struct work_struct *work)

ohci->generation = generation; reg_write(ohci, OHCI1394_IntEventClear, OHCI1394_busReset); + if (param_debug & OHCI_PARAM_DEBUG_BUSRESETS) + reg_write(ohci, OHCI1394_IntMaskSet, OHCI1394_busReset);

if (ohci->quirks & QUIRK_RESET_PACKET) ohci->request_generation = generation; @@ -2115,12 +2117,14 @@ static irqreturn_t irq_handler(int irq, void *data) return IRQ_NONE;

/* - * busReset and postedWriteErr must not be cleared yet + * busReset and postedWriteErr events must not be cleared yet * (OHCI 1.1 clauses 7.2.3.2 and 13.2.8.1) */ reg_write(ohci, OHCI1394_IntEventClear, event & ~(OHCI1394_busReset | OHCI1394_postedWriteErr)); log_irqs(ohci, event); + if (event & OHCI1394_busReset) + reg_write(ohci, OHCI1394_IntMaskClear, OHCI1394_busReset);

if (event & OHCI1394_selfIDComplete) queue_work(selfid_workqueue, &ohci->bus_reset_work);