From: James Smart james.smart@broadcom.com

[ Upstream commit 7b08e89f98cee9907895fabb64cf437bc505ce9a ]

The driver is unable to successfully login with remote device. During pt2pt login, the driver completes its FLOGI request with the remote device having WWN precedence. The remote device issues its own (delayed) FLOGI after accepting the driver's and, upon transmitting the FLOGI, immediately recognizes it has already processed the driver's FLOGI thus it transitions to sending a PLOGI before waiting for an ACC to its FLOGI.

In the driver, the FLOGI is received and an ACC sent, followed by the PLOGI being received and an ACC sent. The issue is that the PLOGI reception occurs before the response from the adapter from the FLOGI ACC is received. Processing of the PLOGI sets state flags to perform the REG_RPI mailbox command and proceed with the rest of discovery on the port. The same completion routine used by both FLOGI and PLOGI is generic in nature. One of the things it does is clear flags, and those flags happen to drive the rest of discovery. So what happened was the PLOGI processing set the flags, the FLOGI ACC completion cleared them, thus when the PLOGI ACC completes it doesn't see the flags and stops.

Fix by modifying the generic completion routine to not clear the rest of discovery flag (NLP_ACC_REGLOGIN) unless the completion is also associated with performing a mailbox command as part of its handling. For things such as FLOGI ACC, there isn't a subsequent action to perform with the adapter, thus there is no mailbox cmd ptr. PLOGI ACC though will perform REG_RPI upon completion, thus there is a mailbox cmd ptr.

Link: https://lore.kernel.org/r/20200828175332.130300-3-james.smart@broadcom.com Co-developed-by: Dick Kennedy dick.kennedy@broadcom.com Signed-off-by: Dick Kennedy dick.kennedy@broadcom.com Signed-off-by: James Smart james.smart@broadcom.com Signed-off-by: Martin K. Petersen martin.petersen@oracle.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/scsi/lpfc/lpfc_els.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/scsi/lpfc/lpfc_els.c b/drivers/scsi/lpfc/lpfc_els.c index 315dd25a0c44e..5be938b47f48b 100644 --- a/drivers/scsi/lpfc/lpfc_els.c +++ b/drivers/scsi/lpfc/lpfc_els.c @@ -3841,7 +3841,9 @@ lpfc_cmpl_els_rsp(struct lpfc_hba *phba, struct lpfc_iocbq *cmdiocb, out: if (ndlp && NLP_CHK_NODE_ACT(ndlp) && shost) { spin_lock_irq(shost->host_lock); - ndlp->nlp_flag &= ~(NLP_ACC_REGLOGIN | NLP_RM_DFLT_RPI); + if (mbox) + ndlp->nlp_flag &= ~NLP_ACC_REGLOGIN; + ndlp->nlp_flag &= ~NLP_RM_DFLT_RPI; spin_unlock_irq(shost->host_lock);

/* If the node is not being used by another discovery thread,

From: Laurent Pinchart laurent.pinchart@ideasonboard.com

[ Upstream commit d2b86100245080cfdf1e95e9e07477474c1be2bd ]

Enabling a whole subsystem from a single driver 'select' is frowned upon and won't be accepted in new drivers, that need to use 'depends on' instead. Existing selection of DMAENGINES will then cause circular dependencies. Replace them with a dependency.

Signed-off-by: Laurent Pinchart laurent.pinchart@ideasonboard.com Acked-by: Randy Dunlap rdunlap@infradead.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/rapidio/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/rapidio/Kconfig b/drivers/rapidio/Kconfig index 3e3be57e9a1a1..4d0c1a40a6e65 100644 --- a/drivers/rapidio/Kconfig +++ b/drivers/rapidio/Kconfig @@ -25,7 +25,7 @@ config RAPIDIO_ENABLE_RX_TX_PORTS config RAPIDIO_DMA_ENGINE bool "DMA Engine support for RapidIO" depends on RAPIDIO - select DMADEVICES + depends on DMADEVICES select DMA_ENGINE help Say Y here if you want to use DMA Engine frameork for RapidIO data

From: Evan Nimmo evan.nimmo@alliedtelesis.co.nz

[ Upstream commit 0a355aeb24081e4538d4d424cd189f16c0bbd983 ]

If something goes wrong (such as the SCL being stuck low) then we need to reset the PCA chip. The issue with this is that on reset we lose all config settings and the chip ends up in a disabled state which results in a lock up/high CPU usage. We need to re-apply any configuration that had previously been set and re-enable the chip.

Signed-off-by: Evan Nimmo evan.nimmo@alliedtelesis.co.nz Reviewed-by: Chris Packham chris.packham@alliedtelesis.co.nz Reviewed-by: Andy Shevchenko andriy.shevchenko@linux.intel.com Signed-off-by: Wolfram Sang wsa@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/i2c/algos/i2c-algo-pca.c | 35 +++++++++++++++++++++----------- include/linux/i2c-algo-pca.h | 15 ++++++++++++++ 2 files changed, 38 insertions(+), 12 deletions(-)

diff --git a/drivers/i2c/algos/i2c-algo-pca.c b/drivers/i2c/algos/i2c-algo-pca.c index 3a9db4626cb60..1886588b9ea3e 100644 --- a/drivers/i2c/algos/i2c-algo-pca.c +++ b/drivers/i2c/algos/i2c-algo-pca.c @@ -50,8 +50,22 @@ static void pca_reset(struct i2c_algo_pca_data *adap) pca_outw(adap, I2C_PCA_INDPTR, I2C_PCA_IPRESET); pca_outw(adap, I2C_PCA_IND, 0xA5); pca_outw(adap, I2C_PCA_IND, 0x5A); + + /* + * After a reset we need to re-apply any configuration + * (calculated in pca_init) to get the bus in a working state. + */ + pca_outw(adap, I2C_PCA_INDPTR, I2C_PCA_IMODE); + pca_outw(adap, I2C_PCA_IND, adap->bus_settings.mode); + pca_outw(adap, I2C_PCA_INDPTR, I2C_PCA_ISCLL); + pca_outw(adap, I2C_PCA_IND, adap->bus_settings.tlow); + pca_outw(adap, I2C_PCA_INDPTR, I2C_PCA_ISCLH); + pca_outw(adap, I2C_PCA_IND, adap->bus_settings.thi); + + pca_set_con(adap, I2C_PCA_CON_ENSIO); } else { adap->reset_chip(adap->data); + pca_set_con(adap, I2C_PCA_CON_ENSIO | adap->bus_settings.clock_freq); } }

@@ -435,13 +449,14 @@ static int pca_init(struct i2c_adapter *adap) " Use the nominal frequency.\n", adap->name); }

- pca_reset(pca_data); - clock = pca_clock(pca_data); printk(KERN_INFO "%s: Clock frequency is %dkHz\n", adap->name, freqs[clock]);

- pca_set_con(pca_data, I2C_PCA_CON_ENSIO | clock); + /* Store settings as these will be needed when the PCA chip is reset */ + pca_data->bus_settings.clock_freq = clock; + + pca_reset(pca_data); } else { int clock; int mode; @@ -508,19 +523,15 @@ static int pca_init(struct i2c_adapter *adap) thi = tlow * min_thi / min_tlow; }

+ /* Store settings as these will be needed when the PCA chip is reset */ + pca_data->bus_settings.mode = mode; + pca_data->bus_settings.tlow = tlow; + pca_data->bus_settings.thi = thi; + pca_reset(pca_data);

printk(KERN_INFO "%s: Clock frequency is %dHz\n", adap->name, clock * 100); - - pca_outw(pca_data, I2C_PCA_INDPTR, I2C_PCA_IMODE); - pca_outw(pca_data, I2C_PCA_IND, mode); - pca_outw(pca_data, I2C_PCA_INDPTR, I2C_PCA_ISCLL); - pca_outw(pca_data, I2C_PCA_IND, tlow); - pca_outw(pca_data, I2C_PCA_INDPTR, I2C_PCA_ISCLH); - pca_outw(pca_data, I2C_PCA_IND, thi); - - pca_set_con(pca_data, I2C_PCA_CON_ENSIO); } udelay(500); /* 500 us for oscillator to stabilise */

diff --git a/include/linux/i2c-algo-pca.h b/include/linux/i2c-algo-pca.h index a3c3ecd59f08c..7a43afd273655 100644 --- a/include/linux/i2c-algo-pca.h +++ b/include/linux/i2c-algo-pca.h @@ -52,6 +52,20 @@ #define I2C_PCA_CON_SI 0x08 /* Serial Interrupt */ #define I2C_PCA_CON_CR 0x07 /* Clock Rate (MASK) */

+/** + * struct pca_i2c_bus_settings - The configured PCA i2c bus settings + * @mode: Configured i2c bus mode + * @tlow: Configured SCL LOW period + * @thi: Configured SCL HIGH period + * @clock_freq: The configured clock frequency + */ +struct pca_i2c_bus_settings { + int mode; + int tlow; + int thi; + int clock_freq; +}; + struct i2c_algo_pca_data { void *data; /* private low level data */ void (*write_byte) (void *data, int reg, int val); @@ -63,6 +77,7 @@ struct i2c_algo_pca_data { * For PCA9665, use the frequency you want here. */ unsigned int i2c_clock; unsigned int chip; + struct pca_i2c_bus_settings bus_settings; };

int i2c_pca_add_bus(struct i2c_adapter *);