From: Matt Redfearn matt.redfearn@thinci.com

[ Upstream commit 83f35bc3a852f1c3892c7474998c5cec707c7ba3 ]

In contrast to all of the DSI panel drivers in drivers/gpu/drm/panel which attach to the DSI host via mipi_dsi_attach() at probe time, the ADV7533 bridge device does not. Instead it defers this to the point that the upstream device connects to its bridge via drm_bridge_attach(). The generic Synopsys MIPI DSI host driver does not register it's own drm_bridge until the MIPI DSI has attached. But it does not call drm_bridge_attach() on the downstream device until the upstream device has attached. This leads to a chicken and the egg failure and the DRM pipeline does not complete. Since all other mipi_dsi_device drivers call mipi_dsi_attach() in probe(), make the adv7533 mipi_dsi_device do the same. This ensures that the Synopsys MIPI DSI host registers it's bridge such that it is available for the upstream device to connect to.

Signed-off-by: Matt Redfearn matt.redfearn@thinci.com Signed-off-by: Andrzej Hajda a.hajda@samsung.com Link: https://patchwork.freedesktop.org/patch/msgid/20190627151740.2277-1-matt.red... Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/gpu/drm/bridge/adv7511/adv7511_drv.c | 12 +++++++++--- 1 file changed, 9 insertions(+), 3 deletions(-)

diff --git a/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c b/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c index e7ddd3e3db920..807827bd910e5 100644 --- a/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c +++ b/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c @@ -874,9 +874,6 @@ static int adv7511_bridge_attach(struct drm_bridge *bridge) &adv7511_connector_helper_funcs); drm_connector_attach_encoder(&adv->connector, bridge->encoder);

- if (adv->type == ADV7533) - ret = adv7533_attach_dsi(adv); - if (adv->i2c_main->irq) regmap_write(adv->regmap, ADV7511_REG_INT_ENABLE(0), ADV7511_INT0_HPD); @@ -1222,8 +1219,17 @@ static int adv7511_probe(struct i2c_client *i2c, const struct i2c_device_id *id) drm_bridge_add(&adv7511->bridge);

adv7511_audio_init(dev, adv7511); + + if (adv7511->type == ADV7533) { + ret = adv7533_attach_dsi(adv7511); + if (ret) + goto err_remove_bridge; + } + return 0;

+err_remove_bridge: + drm_bridge_remove(&adv7511->bridge); err_unregister_cec: i2c_unregister_device(adv7511->i2c_cec); if (adv7511->cec_clk)

From: Lucas Stach l.stach@pengutronix.de

[ Upstream commit f8c6bfc612b56f02e1b8fae699dff12738aaf889 ]

The horizontal blanking periods are too short, as the values are specified for a single LVDS channel. Since this panel is dual LVDS they need to be doubled. With this change the panel reaches its nominal vrefresh rate of 60Fps, instead of the 64Fps with the current wrong blanking.

Philipp Zabel added: The datasheet specifies 960 active clocks + 40/128/160 clocks blanking on each of the two LVDS channels (min/typical/max), so doubled this is now correct.

Signed-off-by: Lucas Stach l.stach@pengutronix.de Reviewed-by: Philipp Zabel p.zabel@pengutronix.de Reviewed-by: Sam Ravnborg sam@ravnborg.org Signed-off-by: Sam Ravnborg sam@ravnborg.org Link: https://patchwork.freedesktop.org/patch/msgid/1562764060.23869.12.camel@peng... Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/gpu/drm/panel/panel-simple.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/gpu/drm/panel/panel-simple.c b/drivers/gpu/drm/panel/panel-simple.c index 5fd94e2060297..654fea2b43124 100644 --- a/drivers/gpu/drm/panel/panel-simple.c +++ b/drivers/gpu/drm/panel/panel-simple.c @@ -689,9 +689,9 @@ static const struct panel_desc auo_g133han01 = { static const struct display_timing auo_g185han01_timings = { .pixelclock = { 120000000, 144000000, 175000000 }, .hactive = { 1920, 1920, 1920 }, - .hfront_porch = { 18, 60, 74 }, - .hback_porch = { 12, 44, 54 }, - .hsync_len = { 10, 24, 32 }, + .hfront_porch = { 36, 120, 148 }, + .hback_porch = { 24, 88, 108 }, + .hsync_len = { 20, 48, 64 }, .vactive = { 1080, 1080, 1080 }, .vfront_porch = { 6, 10, 40 }, .vback_porch = { 2, 5, 20 },

From: Ahmad Fatoum a.fatoum@pengutronix.de

[ Upstream commit 8fabc9c3109a71b3577959a05408153ae69ccd8d ]

To properly synchronize with other devices the fence from the GEM object backing the framebuffer needs to be attached to the atomic state, so the commit work can wait on fence signaling.

Signed-off-by: Ahmad Fatoum a.fatoum@pengutronix.de Signed-off-by: Lucas Stach l.stach@pengutronix.de Acked-by: Philippe Cornu philippe.cornu@st.com Tested-by: Philippe Cornu philippe.cornu@st.com Signed-off-by: Benjamin Gaignard benjamin.gaignard@linaro.org Link: https://patchwork.freedesktop.org/patch/msgid/20190712084228.8338-1-l.stach@... Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/gpu/drm/stm/ltdc.c | 2 ++ 1 file changed, 2 insertions(+)

diff --git a/drivers/gpu/drm/stm/ltdc.c b/drivers/gpu/drm/stm/ltdc.c index 808d9fb627e97..477d0a27b9a5d 100644 --- a/drivers/gpu/drm/stm/ltdc.c +++ b/drivers/gpu/drm/stm/ltdc.c @@ -19,6 +19,7 @@ #include <drm/drm_crtc_helper.h> #include <drm/drm_fb_cma_helper.h> #include <drm/drm_gem_cma_helper.h> +#include <drm/drm_gem_framebuffer_helper.h> #include <drm/drm_of.h> #include <drm/drm_bridge.h> #include <drm/drm_plane_helper.h> @@ -825,6 +826,7 @@ static const struct drm_plane_funcs ltdc_plane_funcs = { };

static const struct drm_plane_helper_funcs ltdc_plane_helper_funcs = { + .prepare_fb = drm_gem_fb_prepare_fb, .atomic_check = ltdc_plane_atomic_check, .atomic_update = ltdc_plane_atomic_update, .atomic_disable = ltdc_plane_atomic_disable,

From: Sean Paul seanpaul@chromium.org

[ Upstream commit ad309284a52be47c8b3126c9376358bf381861bc ]

Once we start shutting off the link during PSR, we're going to want fast training to work. If the display doesn't support fast training, don't enable psr.

Changes in v2: - None Changes in v3: - None Changes in v4: - None Changes in v5: - None

Link to v1: https://patchwork.freedesktop.org/patch/msgid/20190228210939.83386-3-sean@po... Link to v2: https://patchwork.freedesktop.org/patch/msgid/20190326204509.96515-2-sean@po... Link to v3: https://patchwork.freedesktop.org/patch/msgid/20190502194956.218441-9-sean@p... Link to v4: https://patchwork.freedesktop.org/patch/msgid/20190508160920.144739-8-sean@p...

Cc: Zain Wang wzz@rock-chips.com Cc: Tomasz Figa tfiga@chromium.org Tested-by: Heiko Stuebner heiko@sntech.de Reviewed-by: Heiko Stuebner heiko@sntech.de Signed-off-by: Sean Paul seanpaul@chromium.org Link: https://patchwork.freedesktop.org/patch/msgid/20190611160844.257498-8-sean@p... Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/gpu/drm/bridge/analogix/analogix_dp_core.c | 9 +++++---- 1 file changed, 5 insertions(+), 4 deletions(-)

diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c index d68986cea1325..84abf5d6f760a 100644 --- a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c +++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c @@ -1040,16 +1040,17 @@ static int analogix_dp_commit(struct analogix_dp_device *dp) if (ret) return ret;

+ /* Check whether panel supports fast training */ + ret = analogix_dp_fast_link_train_detection(dp); + if (ret) + dp->psr_enable = false; + if (dp->psr_enable) { ret = analogix_dp_enable_sink_psr(dp); if (ret) return ret; }

- /* Check whether panel supports fast training */ - ret = analogix_dp_fast_link_train_detection(dp); - if (ret) - dp->psr_enable = false;

return ret; }

From: Jia-Ju Bai baijiaju1990@gmail.com

[ Upstream commit f3eb9b8f67bc28783eddc142ad805ebdc53d6339 ]

In radeon_connector_set_property(), there is an if statement on line 743 to check whether connector->encoder is NULL: if (connector->encoder)

When connector->encoder is NULL, it is used on line 755: if (connector->encoder->crtc)

Thus, a possible null-pointer dereference may occur.

To fix this bug, connector->encoder is checked before being used.

This bug is found by a static analysis tool STCheck written by us.

Signed-off-by: Jia-Ju Bai baijiaju1990@gmail.com Signed-off-by: Alex Deucher alexander.deucher@amd.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/gpu/drm/radeon/radeon_connectors.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/radeon/radeon_connectors.c b/drivers/gpu/drm/radeon/radeon_connectors.c index 414642e5b7a31..de656f5553839 100644 --- a/drivers/gpu/drm/radeon/radeon_connectors.c +++ b/drivers/gpu/drm/radeon/radeon_connectors.c @@ -751,7 +751,7 @@ static int radeon_connector_set_property(struct drm_connector *connector, struct

radeon_encoder->output_csc = val;

- if (connector->encoder->crtc) { + if (connector->encoder && connector->encoder->crtc) { struct drm_crtc *crtc = connector->encoder->crtc; struct radeon_crtc *radeon_crtc = to_radeon_crtc(crtc);

From: Corey Minyard cminyard@mvista.com

[ Upstream commit 340ff31ab00bca5c15915e70ad9ada3030c98cf8 ]

ipmi_thread() uses back-to-back schedule() to poll for command completion which, on some machines, can push up CPU consumption and heavily tax the scheduler locks leading to noticeable overall performance degradation.

This was originally added so firmware updates through IPMI would complete in a timely manner. But we can't kill the scheduler locks for that one use case.

Instead, only run schedule() continuously in maintenance mode, where firmware updates should run.

Signed-off-by: Corey Minyard cminyard@mvista.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/char/ipmi/ipmi_si_intf.c | 24 +++++++++++++++++++----- 1 file changed, 19 insertions(+), 5 deletions(-)

diff --git a/drivers/char/ipmi/ipmi_si_intf.c b/drivers/char/ipmi/ipmi_si_intf.c index 75e5006f395a5..006d765256782 100644 --- a/drivers/char/ipmi/ipmi_si_intf.c +++ b/drivers/char/ipmi/ipmi_si_intf.c @@ -221,6 +221,9 @@ struct smi_info { */ bool irq_enable_broken;

+ /* Is the driver in maintenance mode? */ + bool in_maintenance_mode; + /* * Did we get an attention that we did not handle? */ @@ -1013,11 +1016,20 @@ static int ipmi_thread(void *data) spin_unlock_irqrestore(&(smi_info->si_lock), flags); busy_wait = ipmi_thread_busy_wait(smi_result, smi_info, &busy_until); - if (smi_result == SI_SM_CALL_WITHOUT_DELAY) + if (smi_result == SI_SM_CALL_WITHOUT_DELAY) { ; /* do nothing */ - else if (smi_result == SI_SM_CALL_WITH_DELAY && busy_wait) - schedule(); - else if (smi_result == SI_SM_IDLE) { + } else if (smi_result == SI_SM_CALL_WITH_DELAY && busy_wait) { + /* + * In maintenance mode we run as fast as + * possible to allow firmware updates to + * complete as fast as possible, but normally + * don't bang on the scheduler. + */ + if (smi_info->in_maintenance_mode) + schedule(); + else + usleep_range(100, 200); + } else if (smi_result == SI_SM_IDLE) { if (atomic_read(&smi_info->need_watch)) { schedule_timeout_interruptible(100); } else { @@ -1025,8 +1037,9 @@ static int ipmi_thread(void *data) __set_current_state(TASK_INTERRUPTIBLE); schedule(); } - } else + } else { schedule_timeout_interruptible(1); + } } return 0; } @@ -1201,6 +1214,7 @@ static void set_maintenance_mode(void *send_info, bool enable)

if (!enable) atomic_set(&smi_info->req_events, 0); + smi_info->in_maintenance_mode = enable; }

static void shutdown_smi(void *send_info);

From: Icenowy Zheng icenowy@aosc.io

[ Upstream commit 720099603d1f62e37b789366d7e89824b009ca28 ]

The MMC2 clock slices are currently not defined in V3s CCU driver, which makes MMC2 not working.

Fix this issue.

Fixes: d0f11d14b0bc ("clk: sunxi-ng: add support for V3s CCU") Signed-off-by: Icenowy Zheng icenowy@aosc.io Signed-off-by: Maxime Ripard maxime.ripard@bootlin.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/clk/sunxi-ng/ccu-sun8i-v3s.c | 3 +++ 1 file changed, 3 insertions(+)

diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-v3s.c b/drivers/clk/sunxi-ng/ccu-sun8i-v3s.c index ac12f261f8caa..9e3f4088724b4 100644 --- a/drivers/clk/sunxi-ng/ccu-sun8i-v3s.c +++ b/drivers/clk/sunxi-ng/ccu-sun8i-v3s.c @@ -499,6 +499,9 @@ static struct clk_hw_onecell_data sun8i_v3s_hw_clks = { [CLK_MMC1] = &mmc1_clk.common.hw, [CLK_MMC1_SAMPLE] = &mmc1_sample_clk.common.hw, [CLK_MMC1_OUTPUT] = &mmc1_output_clk.common.hw, + [CLK_MMC2] = &mmc2_clk.common.hw, + [CLK_MMC2_SAMPLE] = &mmc2_sample_clk.common.hw, + [CLK_MMC2_OUTPUT] = &mmc2_output_clk.common.hw, [CLK_CE] = &ce_clk.common.hw, [CLK_SPI0] = &spi0_clk.common.hw, [CLK_USB_PHY0] = &usb_phy0_clk.common.hw,

From: Lewis Huang Lewis.Huang@amd.com

[ Upstream commit e5382701c3520b3ed66169a6e4aa6ce5df8c56e0 ]

[Why] The vm config will be clear to 0 when system enter S4. It will cause hubbub didn't know how to fetch data when system resume. The flip always pending because earliest_inuse_address and request_address are different.

[How] Reprogram VM config when system resume

Signed-off-by: Lewis Huang Lewis.Huang@amd.com Reviewed-by: Jun Lei Jun.Lei@amd.com Acked-by: Eric Yang eric.yang2@amd.com Acked-by: Leo Li sunpeng.li@amd.com Signed-off-by: Alex Deucher alexander.deucher@amd.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/gpu/drm/amd/display/dc/core/dc.c | 8 ++++++++ 1 file changed, 8 insertions(+)

diff --git a/drivers/gpu/drm/amd/display/dc/core/dc.c b/drivers/gpu/drm/amd/display/dc/core/dc.c index f4b89d1ea6f6f..2b2efe443c36d 100644 --- a/drivers/gpu/drm/amd/display/dc/core/dc.c +++ b/drivers/gpu/drm/amd/display/dc/core/dc.c @@ -1585,6 +1585,14 @@ void dc_set_power_state( dc_resource_state_construct(dc, dc->current_state);

dc->hwss.init_hw(dc); + +#ifdef CONFIG_DRM_AMD_DC_DCN2_0 + if (dc->hwss.init_sys_ctx != NULL && + dc->vm_pa_config.valid) { + dc->hwss.init_sys_ctx(dc->hwseq, dc, &dc->vm_pa_config); + } +#endif + break; default:

From: Ahzo Ahzo@tutanota.com

[ Upstream commit f659bb6dae58c113805f92822e4c16ddd3156b79 ]

This fixes screen corruption/flickering on 75 Hz displays.

v2: make print statement debug only (Alex)

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=102646 Reviewed-by: Evan Quan evan.quan@amd.com Signed-off-by: Ahzo Ahzo@tutanota.com Signed-off-by: Alex Deucher alexander.deucher@amd.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/gpu/drm/amd/powerplay/hwmgr/smu7_hwmgr.c | 5 +++++ 1 file changed, 5 insertions(+)

diff --git a/drivers/gpu/drm/amd/powerplay/hwmgr/smu7_hwmgr.c b/drivers/gpu/drm/amd/powerplay/hwmgr/smu7_hwmgr.c index b52ccab428a9e..c7c505095402d 100644 --- a/drivers/gpu/drm/amd/powerplay/hwmgr/smu7_hwmgr.c +++ b/drivers/gpu/drm/amd/powerplay/hwmgr/smu7_hwmgr.c @@ -4052,6 +4052,11 @@ static int smu7_program_display_gap(struct pp_hwmgr *hwmgr)

data->frame_time_x2 = frame_time_in_us * 2 / 100;

+ if (data->frame_time_x2 < 280) { + pr_debug("%s: enforce minimal VBITimeout: %d -> 280\n", __func__, data->frame_time_x2); + data->frame_time_x2 = 280; + } + display_gap2 = pre_vbi_time_in_us * (ref_clock / 100);

cgs_write_ind_register(hwmgr->device, CGS_IND_REG__SMC, ixCG_DISPLAY_GAP_CNTL2, display_gap2);

From: Stephen Boyd sboyd@kernel.org

[ Upstream commit af55dadfbce35b4f4c6247244ce3e44b2e242b84 ]

A future patch is going to change semantics of clk_register() so that clk_hw::init is guaranteed to be NULL after a clk is registered. Avoid referencing this member here so that we don't run into NULL pointer exceptions.

Cc: Guo Zeng Guo.Zeng@csr.com Cc: Barry Song Baohua.Song@csr.com Signed-off-by: Stephen Boyd sboyd@kernel.org Link: https://lkml.kernel.org/r/20190731193517.237136-6-sboyd@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/clk/sirf/clk-common.c | 12 ++++++++---- 1 file changed, 8 insertions(+), 4 deletions(-)

diff --git a/drivers/clk/sirf/clk-common.c b/drivers/clk/sirf/clk-common.c index d8f9efa5129ad..25351d6a55ba2 100644 --- a/drivers/clk/sirf/clk-common.c +++ b/drivers/clk/sirf/clk-common.c @@ -298,9 +298,10 @@ static u8 dmn_clk_get_parent(struct clk_hw *hw) { struct clk_dmn *clk = to_dmnclk(hw); u32 cfg = clkc_readl(clk->regofs); + const char *name = clk_hw_get_name(hw);

/* parent of io domain can only be pll3 */ - if (strcmp(hw->init->name, "io") == 0) + if (strcmp(name, "io") == 0) return 4;

WARN_ON((cfg & (BIT(3) - 1)) > 4); @@ -312,9 +313,10 @@ static int dmn_clk_set_parent(struct clk_hw *hw, u8 parent) { struct clk_dmn *clk = to_dmnclk(hw); u32 cfg = clkc_readl(clk->regofs); + const char *name = clk_hw_get_name(hw);

/* parent of io domain can only be pll3 */ - if (strcmp(hw->init->name, "io") == 0) + if (strcmp(name, "io") == 0) return -EINVAL;

cfg &= ~(BIT(3) - 1); @@ -354,7 +356,8 @@ static long dmn_clk_round_rate(struct clk_hw *hw, unsigned long rate, { unsigned long fin; unsigned ratio, wait, hold; - unsigned bits = (strcmp(hw->init->name, "mem") == 0) ? 3 : 4; + const char *name = clk_hw_get_name(hw); + unsigned bits = (strcmp(name, "mem") == 0) ? 3 : 4;

fin = *parent_rate; ratio = fin / rate; @@ -376,7 +379,8 @@ static int dmn_clk_set_rate(struct clk_hw *hw, unsigned long rate, struct clk_dmn *clk = to_dmnclk(hw); unsigned long fin; unsigned ratio, wait, hold, reg; - unsigned bits = (strcmp(hw->init->name, "mem") == 0) ? 3 : 4; + const char *name = clk_hw_get_name(hw); + unsigned bits = (strcmp(name, "mem") == 0) ? 3 : 4;

fin = parent_rate; ratio = fin / rate;

From: Stephen Boyd sboyd@kernel.org

[ Upstream commit 1a4549c150e27dbc3aea762e879a88209df6d1a5 ]

A future patch is going to change semantics of clk_register() so that clk_hw::init is guaranteed to be NULL after a clk is registered. Avoid referencing this member here so that we don't run into NULL pointer exceptions.

Cc: Jun Nie jun.nie@linaro.org Cc: Shawn Guo shawnguo@kernel.org Signed-off-by: Stephen Boyd sboyd@kernel.org Link: https://lkml.kernel.org/r/20190815160020.183334-3-sboyd@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/clk/zte/clk-zx296718.c | 109 +++++++++++++++------------------ 1 file changed, 49 insertions(+), 60 deletions(-)

diff --git a/drivers/clk/zte/clk-zx296718.c b/drivers/clk/zte/clk-zx296718.c index 354dd508c5169..8dfb8523b79db 100644 --- a/drivers/clk/zte/clk-zx296718.c +++ b/drivers/clk/zte/clk-zx296718.c @@ -567,6 +567,7 @@ static int __init top_clocks_init(struct device_node *np) { void __iomem *reg_base; int i, ret; + const char *name;

reg_base = of_iomap(np, 0); if (!reg_base) { @@ -576,11 +577,10 @@ static int __init top_clocks_init(struct device_node *np)

for (i = 0; i < ARRAY_SIZE(zx296718_pll_clk); i++) { zx296718_pll_clk[i].reg_base += (uintptr_t)reg_base; + name = zx296718_pll_clk[i].hw.init->name; ret = clk_hw_register(NULL, &zx296718_pll_clk[i].hw); - if (ret) { - pr_warn("top clk %s init error!\n", - zx296718_pll_clk[i].hw.init->name); - } + if (ret) + pr_warn("top clk %s init error!\n", name); }

for (i = 0; i < ARRAY_SIZE(top_ffactor_clk); i++) { @@ -588,11 +588,10 @@ static int __init top_clocks_init(struct device_node *np) top_hw_onecell_data.hws[top_ffactor_clk[i].id] = &top_ffactor_clk[i].factor.hw;

+ name = top_ffactor_clk[i].factor.hw.init->name; ret = clk_hw_register(NULL, &top_ffactor_clk[i].factor.hw); - if (ret) { - pr_warn("top clk %s init error!\n", - top_ffactor_clk[i].factor.hw.init->name); - } + if (ret) + pr_warn("top clk %s init error!\n", name); }

for (i = 0; i < ARRAY_SIZE(top_mux_clk); i++) { @@ -601,11 +600,10 @@ static int __init top_clocks_init(struct device_node *np) &top_mux_clk[i].mux.hw;

top_mux_clk[i].mux.reg += (uintptr_t)reg_base; + name = top_mux_clk[i].mux.hw.init->name; ret = clk_hw_register(NULL, &top_mux_clk[i].mux.hw); - if (ret) { - pr_warn("top clk %s init error!\n", - top_mux_clk[i].mux.hw.init->name); - } + if (ret) + pr_warn("top clk %s init error!\n", name); }

for (i = 0; i < ARRAY_SIZE(top_gate_clk); i++) { @@ -614,11 +612,10 @@ static int __init top_clocks_init(struct device_node *np) &top_gate_clk[i].gate.hw;

top_gate_clk[i].gate.reg += (uintptr_t)reg_base; + name = top_gate_clk[i].gate.hw.init->name; ret = clk_hw_register(NULL, &top_gate_clk[i].gate.hw); - if (ret) { - pr_warn("top clk %s init error!\n", - top_gate_clk[i].gate.hw.init->name); - } + if (ret) + pr_warn("top clk %s init error!\n", name); }

for (i = 0; i < ARRAY_SIZE(top_div_clk); i++) { @@ -627,11 +624,10 @@ static int __init top_clocks_init(struct device_node *np) &top_div_clk[i].div.hw;

top_div_clk[i].div.reg += (uintptr_t)reg_base; + name = top_div_clk[i].div.hw.init->name; ret = clk_hw_register(NULL, &top_div_clk[i].div.hw); - if (ret) { - pr_warn("top clk %s init error!\n", - top_div_clk[i].div.hw.init->name); - } + if (ret) + pr_warn("top clk %s init error!\n", name); }

ret = of_clk_add_hw_provider(np, of_clk_hw_onecell_get, @@ -757,6 +753,7 @@ static int __init lsp0_clocks_init(struct device_node *np) { void __iomem *reg_base; int i, ret; + const char *name;

reg_base = of_iomap(np, 0); if (!reg_base) { @@ -770,11 +767,10 @@ static int __init lsp0_clocks_init(struct device_node *np) &lsp0_mux_clk[i].mux.hw;

lsp0_mux_clk[i].mux.reg += (uintptr_t)reg_base; + name = lsp0_mux_clk[i].mux.hw.init->name; ret = clk_hw_register(NULL, &lsp0_mux_clk[i].mux.hw); - if (ret) { - pr_warn("lsp0 clk %s init error!\n", - lsp0_mux_clk[i].mux.hw.init->name); - } + if (ret) + pr_warn("lsp0 clk %s init error!\n", name); }

for (i = 0; i < ARRAY_SIZE(lsp0_gate_clk); i++) { @@ -783,11 +779,10 @@ static int __init lsp0_clocks_init(struct device_node *np) &lsp0_gate_clk[i].gate.hw;

lsp0_gate_clk[i].gate.reg += (uintptr_t)reg_base; + name = lsp0_gate_clk[i].gate.hw.init->name; ret = clk_hw_register(NULL, &lsp0_gate_clk[i].gate.hw); - if (ret) { - pr_warn("lsp0 clk %s init error!\n", - lsp0_gate_clk[i].gate.hw.init->name); - } + if (ret) + pr_warn("lsp0 clk %s init error!\n", name); }

for (i = 0; i < ARRAY_SIZE(lsp0_div_clk); i++) { @@ -796,11 +791,10 @@ static int __init lsp0_clocks_init(struct device_node *np) &lsp0_div_clk[i].div.hw;

lsp0_div_clk[i].div.reg += (uintptr_t)reg_base; + name = lsp0_div_clk[i].div.hw.init->name; ret = clk_hw_register(NULL, &lsp0_div_clk[i].div.hw); - if (ret) { - pr_warn("lsp0 clk %s init error!\n", - lsp0_div_clk[i].div.hw.init->name); - } + if (ret) + pr_warn("lsp0 clk %s init error!\n", name); }

ret = of_clk_add_hw_provider(np, of_clk_hw_onecell_get, @@ -865,6 +859,7 @@ static int __init lsp1_clocks_init(struct device_node *np) { void __iomem *reg_base; int i, ret; + const char *name;

reg_base = of_iomap(np, 0); if (!reg_base) { @@ -878,11 +873,10 @@ static int __init lsp1_clocks_init(struct device_node *np) &lsp0_mux_clk[i].mux.hw;

lsp1_mux_clk[i].mux.reg += (uintptr_t)reg_base; + name = lsp1_mux_clk[i].mux.hw.init->name; ret = clk_hw_register(NULL, &lsp1_mux_clk[i].mux.hw); - if (ret) { - pr_warn("lsp1 clk %s init error!\n", - lsp1_mux_clk[i].mux.hw.init->name); - } + if (ret) + pr_warn("lsp1 clk %s init error!\n", name); }

for (i = 0; i < ARRAY_SIZE(lsp1_gate_clk); i++) { @@ -891,11 +885,10 @@ static int __init lsp1_clocks_init(struct device_node *np) &lsp1_gate_clk[i].gate.hw;

lsp1_gate_clk[i].gate.reg += (uintptr_t)reg_base; + name = lsp1_gate_clk[i].gate.hw.init->name; ret = clk_hw_register(NULL, &lsp1_gate_clk[i].gate.hw); - if (ret) { - pr_warn("lsp1 clk %s init error!\n", - lsp1_gate_clk[i].gate.hw.init->name); - } + if (ret) + pr_warn("lsp1 clk %s init error!\n", name); }

for (i = 0; i < ARRAY_SIZE(lsp1_div_clk); i++) { @@ -904,11 +897,10 @@ static int __init lsp1_clocks_init(struct device_node *np) &lsp1_div_clk[i].div.hw;

lsp1_div_clk[i].div.reg += (uintptr_t)reg_base; + name = lsp1_div_clk[i].div.hw.init->name; ret = clk_hw_register(NULL, &lsp1_div_clk[i].div.hw); - if (ret) { - pr_warn("lsp1 clk %s init error!\n", - lsp1_div_clk[i].div.hw.init->name); - } + if (ret) + pr_warn("lsp1 clk %s init error!\n", name); }

ret = of_clk_add_hw_provider(np, of_clk_hw_onecell_get, @@ -982,6 +974,7 @@ static int __init audio_clocks_init(struct device_node *np) { void __iomem *reg_base; int i, ret; + const char *name;

reg_base = of_iomap(np, 0); if (!reg_base) { @@ -995,11 +988,10 @@ static int __init audio_clocks_init(struct device_node *np) &audio_mux_clk[i].mux.hw;

audio_mux_clk[i].mux.reg += (uintptr_t)reg_base; + name = audio_mux_clk[i].mux.hw.init->name; ret = clk_hw_register(NULL, &audio_mux_clk[i].mux.hw); - if (ret) { - pr_warn("audio clk %s init error!\n", - audio_mux_clk[i].mux.hw.init->name); - } + if (ret) + pr_warn("audio clk %s init error!\n", name); }

for (i = 0; i < ARRAY_SIZE(audio_adiv_clk); i++) { @@ -1008,11 +1000,10 @@ static int __init audio_clocks_init(struct device_node *np) &audio_adiv_clk[i].hw;

audio_adiv_clk[i].reg_base += (uintptr_t)reg_base; + name = audio_adiv_clk[i].hw.init->name; ret = clk_hw_register(NULL, &audio_adiv_clk[i].hw); - if (ret) { - pr_warn("audio clk %s init error!\n", - audio_adiv_clk[i].hw.init->name); - } + if (ret) + pr_warn("audio clk %s init error!\n", name); }

for (i = 0; i < ARRAY_SIZE(audio_div_clk); i++) { @@ -1021,11 +1012,10 @@ static int __init audio_clocks_init(struct device_node *np) &audio_div_clk[i].div.hw;

audio_div_clk[i].div.reg += (uintptr_t)reg_base; + name = audio_div_clk[i].div.hw.init->name; ret = clk_hw_register(NULL, &audio_div_clk[i].div.hw); - if (ret) { - pr_warn("audio clk %s init error!\n", - audio_div_clk[i].div.hw.init->name); - } + if (ret) + pr_warn("audio clk %s init error!\n", name); }

for (i = 0; i < ARRAY_SIZE(audio_gate_clk); i++) { @@ -1034,11 +1024,10 @@ static int __init audio_clocks_init(struct device_node *np) &audio_gate_clk[i].gate.hw;

audio_gate_clk[i].gate.reg += (uintptr_t)reg_base; + name = audio_gate_clk[i].gate.hw.init->name; ret = clk_hw_register(NULL, &audio_gate_clk[i].gate.hw); - if (ret) { - pr_warn("audio clk %s init error!\n", - audio_gate_clk[i].gate.hw.init->name); - } + if (ret) + pr_warn("audio clk %s init error!\n", name); }

ret = of_clk_add_hw_provider(np, of_clk_hw_onecell_get,

From: Nathan Lynch nathanl@linux.ibm.com

[ Upstream commit a6717c01ddc259f6f73364779df058e2c67309f8 ]

The LPAR migration implementation and userspace-initiated cpu hotplug can interleave their executions like so:

1. Set cpu 7 offline via sysfs.

2. Begin a partition migration, whose implementation requires the OS to ensure all present cpus are online; cpu 7 is onlined:

rtas_ibm_suspend_me -> rtas_online_cpus_mask -> cpu_up

This sets cpu 7 online in all respects except for the cpu's corresponding struct device; dev->offline remains true.

3. Set cpu 7 online via sysfs. _cpu_up() determines that cpu 7 is already online and returns success. The driver core (device_online) sets dev->offline = false.

4. The migration completes and restores cpu 7 to offline state:

rtas_ibm_suspend_me -> rtas_offline_cpus_mask -> cpu_down

This leaves cpu7 in a state where the driver core considers the cpu device online, but in all other respects it is offline and unused. Attempts to online the cpu via sysfs appear to succeed but the driver core actually does not pass the request to the lower-level cpuhp support code. This makes the cpu unusable until the cpu device is manually set offline and then online again via sysfs.

Instead of directly calling cpu_up/cpu_down, the migration code should use the higher-level device core APIs to maintain consistent state and serialize operations.

Fixes: 120496ac2d2d ("powerpc: Bring all threads online prior to migration/hibernation") Signed-off-by: Nathan Lynch nathanl@linux.ibm.com Reviewed-by: Gautham R. Shenoy ego@linux.vnet.ibm.com Signed-off-by: Michael Ellerman mpe@ellerman.id.au Link: https://lore.kernel.org/r/20190802192926.19277-2-nathanl@linux.ibm.com Signed-off-by: Sasha Levin sashal@kernel.org --- arch/powerpc/kernel/rtas.c | 11 ++++++++--- 1 file changed, 8 insertions(+), 3 deletions(-)

diff --git a/arch/powerpc/kernel/rtas.c b/arch/powerpc/kernel/rtas.c index 8afd146bc9c70..9e41a9de43235 100644 --- a/arch/powerpc/kernel/rtas.c +++ b/arch/powerpc/kernel/rtas.c @@ -875,15 +875,17 @@ static int rtas_cpu_state_change_mask(enum rtas_cpu_state state, return 0;

for_each_cpu(cpu, cpus) { + struct device *dev = get_cpu_device(cpu); + switch (state) { case DOWN: - cpuret = cpu_down(cpu); + cpuret = device_offline(dev); break; case UP: - cpuret = cpu_up(cpu); + cpuret = device_online(dev); break; } - if (cpuret) { + if (cpuret < 0) { pr_debug("%s: cpu_%s for cpu#%d returned %d.\n", __func__, ((state == UP) ? "up" : "down"), @@ -972,6 +974,8 @@ int rtas_ibm_suspend_me(u64 handle) data.token = rtas_token("ibm,suspend-me"); data.complete = &done;

+ lock_device_hotplug(); + /* All present CPUs must be online */ cpumask_andnot(offline_mask, cpu_present_mask, cpu_online_mask); cpuret = rtas_online_cpus_mask(offline_mask); @@ -1003,6 +1007,7 @@ int rtas_ibm_suspend_me(u64 handle) __func__);

out: + unlock_device_hotplug(); free_cpumask_var(offline_mask); return atomic_read(&data.error); }

From: Nicholas Piggin npiggin@gmail.com

[ Upstream commit 6bb25170d7a44ef0ed9677814600f0785e7421d1 ]

pfn_pte is never given a pte above the addressable physical memory limit, so the masking is redundant. In case of a software bug, it is not obviously better to silently truncate the pfn than to corrupt the pte (either one will result in memory corruption or crashes), so there is no reason to add this to the fast path.

Add VM_BUG_ON to catch cases where the pfn is invalid. These would catch the create_section_mapping bug fixed by a previous commit.

[16885.256466] ------------[ cut here ]------------ [16885.256492] kernel BUG at arch/powerpc/include/asm/book3s/64/pgtable.h:612! cpu 0x0: Vector: 700 (Program Check) at [c0000000ee0a36d0] pc: c000000000080738: __map_kernel_page+0x248/0x6f0 lr: c000000000080ac0: __map_kernel_page+0x5d0/0x6f0 sp: c0000000ee0a3960 msr: 9000000000029033 current = 0xc0000000ec63b400 paca = 0xc0000000017f0000 irqmask: 0x03 irq_happened: 0x01 pid = 85, comm = sh kernel BUG at arch/powerpc/include/asm/book3s/64/pgtable.h:612! Linux version 5.3.0-rc1-00001-g0fe93e5f3394 enter ? for help [c0000000ee0a3a00] c000000000d37378 create_physical_mapping+0x260/0x360 [c0000000ee0a3b10] c000000000d370bc create_section_mapping+0x1c/0x3c [c0000000ee0a3b30] c000000000071f54 arch_add_memory+0x74/0x130

Signed-off-by: Nicholas Piggin npiggin@gmail.com Reviewed-by: Aneesh Kumar K.V aneesh.kumar@linux.ibm.com Signed-off-by: Michael Ellerman mpe@ellerman.id.au Link: https://lore.kernel.org/r/20190724084638.24982-5-npiggin@gmail.com Signed-off-by: Sasha Levin sashal@kernel.org --- arch/powerpc/include/asm/book3s/64/pgtable.h | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/arch/powerpc/include/asm/book3s/64/pgtable.h b/arch/powerpc/include/asm/book3s/64/pgtable.h index 855dbae6d351d..a717640b7eda4 100644 --- a/arch/powerpc/include/asm/book3s/64/pgtable.h +++ b/arch/powerpc/include/asm/book3s/64/pgtable.h @@ -629,8 +629,10 @@ static inline bool pte_access_permitted(pte_t pte, bool write) */ static inline pte_t pfn_pte(unsigned long pfn, pgprot_t pgprot) { - return __pte((((pte_basic_t)(pfn) << PAGE_SHIFT) & PTE_RPN_MASK) | - pgprot_val(pgprot)); + VM_BUG_ON(pfn >> (64 - PAGE_SHIFT)); + VM_BUG_ON((pfn << PAGE_SHIFT) & ~PTE_RPN_MASK); + + return __pte(((pte_basic_t)pfn << PAGE_SHIFT) | pgprot_val(pgprot)); }

static inline unsigned long pte_pfn(pte_t pte)

From: Sowjanya Komatineni skomatineni@nvidia.com

[ Upstream commit c2cf351eba2ff6002ce8eb178452219d2521e38e ]

pmx_writel uses writel which inserts write barrier before the register write.

This patch has fix to replace writel with writel_relaxed followed by a readback and memory barrier to ensure write operation is completed for successful pinctrl change.

Acked-by: Thierry Reding treding@nvidia.com Reviewed-by: Dmitry Osipenko digetx@gmail.com Signed-off-by: Sowjanya Komatineni skomatineni@nvidia.com Link: https://lore.kernel.org/r/1565984527-5272-2-git-send-email-skomatineni@nvidi... Signed-off-by: Linus Walleij linus.walleij@linaro.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/pinctrl/tegra/pinctrl-tegra.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/pinctrl/tegra/pinctrl-tegra.c b/drivers/pinctrl/tegra/pinctrl-tegra.c index 1aba75897d147..26a3f1eb9c6bf 100644 --- a/drivers/pinctrl/tegra/pinctrl-tegra.c +++ b/drivers/pinctrl/tegra/pinctrl-tegra.c @@ -40,7 +40,9 @@ static inline u32 pmx_readl(struct tegra_pmx *pmx, u32 bank, u32 reg)

static inline void pmx_writel(struct tegra_pmx *pmx, u32 val, u32 bank, u32 reg) { - writel(val, pmx->regs[bank] + reg); + writel_relaxed(val, pmx->regs[bank] + reg); + /* make sure pinmux register write completed */ + pmx_readl(pmx, bank, reg); }

static int tegra_pinctrl_get_groups_count(struct pinctrl_dev *pctldev)

From: hexin hexin.op@gmail.com

[ Upstream commit 92c8026854c25093946e0d7fe536fd9eac440f06 ]

vfio_pci_enable() saves the device's initial configuration information with the intent that it is restored in vfio_pci_disable(). However, the commit referenced in Fixes: below replaced the call to __pci_reset_function_locked(), which is not wrapped in a state save and restore, with pci_try_reset_function(), which overwrites the restored device state with the current state before applying it to the device. Reinstate use of __pci_reset_function_locked() to return to the desired behavior.

Fixes: 890ed578df82 ("vfio-pci: Use pci "try" reset interface") Signed-off-by: hexin hexin15@baidu.com Signed-off-by: Liu Qi liuqi16@baidu.com Signed-off-by: Zhang Yu zhangyu31@baidu.com Signed-off-by: Alex Williamson alex.williamson@redhat.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/vfio/pci/vfio_pci.c | 17 +++++++++++++---- 1 file changed, 13 insertions(+), 4 deletions(-)

diff --git a/drivers/vfio/pci/vfio_pci.c b/drivers/vfio/pci/vfio_pci.c index 6cf00d9f512b7..a92c2868d9021 100644 --- a/drivers/vfio/pci/vfio_pci.c +++ b/drivers/vfio/pci/vfio_pci.c @@ -373,11 +373,20 @@ static void vfio_pci_disable(struct vfio_pci_device *vdev) pci_write_config_word(pdev, PCI_COMMAND, PCI_COMMAND_INTX_DISABLE);

/* - * Try to reset the device. The success of this is dependent on - * being able to lock the device, which is not always possible. + * Try to get the locks ourselves to prevent a deadlock. The + * success of this is dependent on being able to lock the device, + * which is not always possible. + * We can not use the "try" reset interface here, which will + * overwrite the previously restored configuration information. */ - if (vdev->reset_works && !pci_try_reset_function(pdev)) - vdev->needs_reset = false; + if (vdev->reset_works && pci_cfg_access_trylock(pdev)) { + if (device_trylock(&pdev->dev)) { + if (!__pci_reset_function_locked(pdev)) + vdev->needs_reset = false; + device_unlock(&pdev->dev); + } + pci_cfg_access_unlock(pdev); + }

pci_restore_state(pdev); out:

From: Daniel Drake drake@endlessm.com

[ Upstream commit d21b8adbd475dba19ac2086d3306327b4a297418 ]

When cold-booting Asus X434DA, GPIO 7 is found to be already configured as an interrupt, and the GPIO level is found to be in a state that causes the interrupt to fire.

As soon as pinctrl-amd probes, this interrupt fires and invokes amd_gpio_irq_handler(). The IRQ is acked, but no GPIO-IRQ handler was invoked, so the GPIO level being unchanged just causes another interrupt to fire again immediately after.

This results in an interrupt storm causing this platform to hang during boot, right after pinctrl-amd is probed.

Detect this situation and disable the GPIO interrupt when this happens. This enables the affected platform to boot as normal. GPIO 7 actually is the I2C touchpad interrupt line, and later on, i2c-multitouch loads and re-enables this interrupt when it is ready to handle it.

Instead of this approach, I considered disabling all GPIO interrupts at probe time, however that seems a little risky, and I also confirmed that Windows does not seem to have this behaviour: the same 41 GPIO IRQs are enabled under both Linux and Windows, which is a far larger collection than the GPIOs referenced by the DSDT on this platform.

Signed-off-by: Daniel Drake drake@endlessm.com Link: https://lore.kernel.org/r/20190814090540.7152-1-drake@endlessm.com Signed-off-by: Linus Walleij linus.walleij@linaro.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/pinctrl/pinctrl-amd.c | 12 +++++++++++- 1 file changed, 11 insertions(+), 1 deletion(-)

diff --git a/drivers/pinctrl/pinctrl-amd.c b/drivers/pinctrl/pinctrl-amd.c index 1425c2874d402..cd7a5d95b499a 100644 --- a/drivers/pinctrl/pinctrl-amd.c +++ b/drivers/pinctrl/pinctrl-amd.c @@ -569,15 +569,25 @@ static irqreturn_t amd_gpio_irq_handler(int irq, void *dev_id) !(regval & BIT(INTERRUPT_MASK_OFF))) continue; irq = irq_find_mapping(gc->irq.domain, irqnr + i); - generic_handle_irq(irq); + if (irq != 0) + generic_handle_irq(irq);

/* Clear interrupt. * We must read the pin register again, in case the * value was changed while executing * generic_handle_irq() above. + * If we didn't find a mapping for the interrupt, + * disable it in order to avoid a system hang caused + * by an interrupt storm. */ raw_spin_lock_irqsave(&gpio_dev->lock, flags); regval = readl(regs + i); + if (irq == 0) { + regval &= ~BIT(INTERRUPT_ENABLE_OFF); + dev_dbg(&gpio_dev->pdev->dev, + "Disabling spurious GPIO IRQ %d\n", + irqnr + i); + } writel(regval, regs + i); raw_spin_unlock_irqrestore(&gpio_dev->lock, flags); ret = IRQ_HANDLED;

From: Geert Uytterhoeven geert+renesas@glider.be

[ Upstream commit f787216f33ce5b5a2567766398f44ab62157114c ]

The CPG/MSSR Clock Domain driver does not implement the generic_pm_domain.power_{on,off}() callbacks, as the domain itself cannot be powered down. Hence the domain should be marked as always-on by setting the GENPD_FLAG_ALWAYS_ON flag, to prevent the core PM Domain code from considering it for power-off, and doing unnessary processing.

Note that this only affects RZ/A2 SoCs. On R-Car Gen2 and Gen3 SoCs, the R-Car SYSC driver handles Clock Domain creation, and offloads only device attachment/detachment to the CPG/MSSR driver.

Signed-off-by: Geert Uytterhoeven geert+renesas@glider.be Reviewed-by: Simon Horman horms+renesas@verge.net.au Reviewed-by: Ulf Hansson ulf.hansson@linaro.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/clk/renesas/renesas-cpg-mssr.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/clk/renesas/renesas-cpg-mssr.c b/drivers/clk/renesas/renesas-cpg-mssr.c index 24485bee9b49e..d7a2ad6173694 100644 --- a/drivers/clk/renesas/renesas-cpg-mssr.c +++ b/drivers/clk/renesas/renesas-cpg-mssr.c @@ -514,7 +514,8 @@ static int __init cpg_mssr_add_clk_domain(struct device *dev,

genpd = &pd->genpd; genpd->name = np->name; - genpd->flags = GENPD_FLAG_PM_CLK | GENPD_FLAG_ACTIVE_WAKEUP; + genpd->flags = GENPD_FLAG_PM_CLK | GENPD_FLAG_ALWAYS_ON | + GENPD_FLAG_ACTIVE_WAKEUP; genpd->attach_dev = cpg_mssr_attach_dev; genpd->detach_dev = cpg_mssr_detach_dev; pm_genpd_init(genpd, &pm_domain_always_on_gov, false);

From: Jean Delvare jdelvare@suse.de

[ Upstream commit 77efe48a729588527afb4d5811b9e0acb29f5e51 ]

Comparing adev->family with CHIP constants is not correct. adev->family can only be compared with AMDGPU_FAMILY constants and adev->asic_type is the struct member to compare with CHIP constants. They are separate identification spaces.

Signed-off-by: Jean Delvare jdelvare@suse.de Fixes: 62a37553414a ("drm/amdgpu: add si implementation v10") Cc: Ken Wang Qingqing.Wang@amd.com Cc: Alex Deucher alexander.deucher@amd.com Cc: "Christian König" christian.koenig@amd.com Cc: "David (ChunMing) Zhou" David1.Zhou@amd.com Signed-off-by: Alex Deucher alexander.deucher@amd.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/gpu/drm/amd/amdgpu/si.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/gpu/drm/amd/amdgpu/si.c b/drivers/gpu/drm/amd/amdgpu/si.c index c364ef94cc366..77c9f4d8668ad 100644 --- a/drivers/gpu/drm/amd/amdgpu/si.c +++ b/drivers/gpu/drm/amd/amdgpu/si.c @@ -1813,7 +1813,7 @@ static void si_program_aspm(struct amdgpu_device *adev) if (orig != data) si_pif_phy1_wreg(adev,PB1_PIF_PWRDOWN_1, data);

- if ((adev->family != CHIP_OLAND) && (adev->family != CHIP_HAINAN)) { + if ((adev->asic_type != CHIP_OLAND) && (adev->asic_type != CHIP_HAINAN)) { orig = data = si_pif_phy0_rreg(adev,PB0_PIF_PWRDOWN_0); data &= ~PLL_RAMP_UP_TIME_0_MASK; if (orig != data) @@ -1862,14 +1862,14 @@ static void si_program_aspm(struct amdgpu_device *adev)

orig = data = si_pif_phy0_rreg(adev,PB0_PIF_CNTL); data &= ~LS2_EXIT_TIME_MASK; - if ((adev->family == CHIP_OLAND) || (adev->family == CHIP_HAINAN)) + if ((adev->asic_type == CHIP_OLAND) || (adev->asic_type == CHIP_HAINAN)) data |= LS2_EXIT_TIME(5); if (orig != data) si_pif_phy0_wreg(adev,PB0_PIF_CNTL, data);

orig = data = si_pif_phy1_rreg(adev,PB1_PIF_CNTL); data &= ~LS2_EXIT_TIME_MASK; - if ((adev->family == CHIP_OLAND) || (adev->family == CHIP_HAINAN)) + if ((adev->asic_type == CHIP_OLAND) || (adev->asic_type == CHIP_HAINAN)) data |= LS2_EXIT_TIME(5); if (orig != data) si_pif_phy1_wreg(adev,PB1_PIF_CNTL, data);

From: Deepa Dinamani deepa.kernel@gmail.com

[ Upstream commit 83b8a3fbe3aa82ac3c253b698ae6a9be2dbdd5e0 ]

Leaving granularity at 1ns because it is dependent on the specific attached backing pstore module. ramoops has microsecond resolution.

Fix the readback of ramoops fractional timestamp microseconds, which has incorrectly been reporting the value as nanoseconds.

Fixes: 3f8f80f0cfeb ("pstore/ram: Read and write to the 'compressed' flag of pstore").

Signed-off-by: Deepa Dinamani deepa.kernel@gmail.com Acked-by: Kees Cook keescook@chromium.org Acked-by: Jeff Layton jlayton@kernel.org Cc: anton@enomsg.org Cc: ccross@android.com Cc: keescook@chromium.org Cc: tony.luck@intel.com Signed-off-by: Sasha Levin sashal@kernel.org --- fs/pstore/ram.c | 2 ++ 1 file changed, 2 insertions(+)

diff --git a/fs/pstore/ram.c b/fs/pstore/ram.c index 316c16463b20f..015d74ee31a03 100644 --- a/fs/pstore/ram.c +++ b/fs/pstore/ram.c @@ -162,6 +162,7 @@ static int ramoops_read_kmsg_hdr(char *buffer, struct timespec64 *time, if (sscanf(buffer, RAMOOPS_KERNMSG_HDR "%lld.%lu-%c\n%n", (time64_t *)&time->tv_sec, &time->tv_nsec, &data_type, &header_length) == 3) { + time->tv_nsec *= 1000; if (data_type == 'C') *compressed = true; else @@ -169,6 +170,7 @@ static int ramoops_read_kmsg_hdr(char *buffer, struct timespec64 *time, } else if (sscanf(buffer, RAMOOPS_KERNMSG_HDR "%lld.%lu\n%n", (time64_t *)&time->tv_sec, &time->tv_nsec, &header_length) == 2) { + time->tv_nsec *= 1000; *compressed = false; } else { time->tv_sec = 0;

From: Stephen Boyd swboyd@chromium.org

[ Upstream commit 5e4b7e82d497580bc430576c4c9bce157dd72512 ]

Some MMC cards fail to enumerate properly when inserted into an MMC slot on sdm845 devices. This is because the clk ops for qcom clks round the frequency up to the nearest rate instead of down to the nearest rate. For example, the MMC driver requests a frequency of 52MHz from clk_set_rate() but the qcom implementation for these clks rounds 52MHz up to the next supported frequency of 100MHz. The MMC driver could be modified to request clk rate ranges but for now we can fix this in the clk driver by changing the rounding policy for this clk to be round down instead of round up.

Fixes: 06391eddb60a ("clk: qcom: Add Global Clock controller (GCC) driver for SDM845") Reported-by: Douglas Anderson dianders@chromium.org Cc: Taniya Das tdas@codeaurora.org Signed-off-by: Stephen Boyd swboyd@chromium.org Link: https://lkml.kernel.org/r/20190830195142.103564-1-swboyd@chromium.org Reviewed-by: Douglas Anderson dianders@chromium.org Signed-off-by: Stephen Boyd sboyd@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/clk/qcom/gcc-sdm845.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/clk/qcom/gcc-sdm845.c b/drivers/clk/qcom/gcc-sdm845.c index 3bf11a6200942..ada3e4aeb38f9 100644 --- a/drivers/clk/qcom/gcc-sdm845.c +++ b/drivers/clk/qcom/gcc-sdm845.c @@ -647,7 +647,7 @@ static struct clk_rcg2 gcc_sdcc2_apps_clk_src = { .name = "gcc_sdcc2_apps_clk_src", .parent_names = gcc_parent_names_10, .num_parents = 5, - .ops = &clk_rcg2_ops, + .ops = &clk_rcg2_floor_ops, }, };

@@ -671,7 +671,7 @@ static struct clk_rcg2 gcc_sdcc4_apps_clk_src = { .name = "gcc_sdcc4_apps_clk_src", .parent_names = gcc_parent_names_0, .num_parents = 4, - .ops = &clk_rcg2_ops, + .ops = &clk_rcg2_floor_ops, }, };

From: Otto Meier gf435@gmx.net

[ Upstream commit cb0438e4436085d89706b5ccfce4d5da531253de ]

Hi i tried to use the uart_C of the the odroid-c2.

I enabled it in the dts file. During boot it crashed when the the sdcard slot is addressed.

After long search in the net i found this:

https://forum.odroid.com/viewtopic.php?f=139&t=25371&p=194370&hi...

After changing the pin definitions accordingly erverything works. Uart_c is functioning and sdcard ist working.

Fixes: 6db0f3a8a04e46 ("pinctrl: amlogic: gxbb: add more UART pins") Signed-off-by: Otto Meier gf435@gmx.net Link: https://lore.kernel.org/r/1cc32a18-464d-5531-7a1c-084390e2ecb1@gmx.net Signed-off-by: Linus Walleij linus.walleij@linaro.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/pinctrl/meson/pinctrl-meson-gxbb.c | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/drivers/pinctrl/meson/pinctrl-meson-gxbb.c b/drivers/pinctrl/meson/pinctrl-meson-gxbb.c index 4edeb4cae72aa..c4c70dc57dbee 100644 --- a/drivers/pinctrl/meson/pinctrl-meson-gxbb.c +++ b/drivers/pinctrl/meson/pinctrl-meson-gxbb.c @@ -198,8 +198,8 @@ static const unsigned int uart_rts_b_pins[] = { GPIODV_27 };

static const unsigned int uart_tx_c_pins[] = { GPIOY_13 }; static const unsigned int uart_rx_c_pins[] = { GPIOY_14 }; -static const unsigned int uart_cts_c_pins[] = { GPIOX_11 }; -static const unsigned int uart_rts_c_pins[] = { GPIOX_12 }; +static const unsigned int uart_cts_c_pins[] = { GPIOY_11 }; +static const unsigned int uart_rts_c_pins[] = { GPIOY_12 };

static const unsigned int i2c_sck_a_pins[] = { GPIODV_25 }; static const unsigned int i2c_sda_a_pins[] = { GPIODV_24 }; @@ -445,10 +445,10 @@ static struct meson_pmx_group meson_gxbb_periphs_groups[] = { GROUP(pwm_f_x, 3, 18),

/* Bank Y */ - GROUP(uart_cts_c, 1, 19), - GROUP(uart_rts_c, 1, 18), - GROUP(uart_tx_c, 1, 17), - GROUP(uart_rx_c, 1, 16), + GROUP(uart_cts_c, 1, 17), + GROUP(uart_rts_c, 1, 16), + GROUP(uart_tx_c, 1, 19), + GROUP(uart_rx_c, 1, 18), GROUP(pwm_a_y, 1, 21), GROUP(pwm_f_y, 1, 20), GROUP(i2s_out_ch23_y, 1, 5),

From: Eugen Hristev eugen.hristev@microchip.com

[ Upstream commit 69a6bcde7fd3fe6f3268ce26f31d9d9378384c98 ]

Selecting the right parent for the main clock is done using only main oscillator enabled bit. In case we have this oscillator bypassed by an external signal (no driving on the XOUT line), we still use external clock, but with BYPASS bit set. So, in this case we must select the same parent as before. Create a macro that will select the right parent considering both bits from the MOR register. Use this macro when looking for the right parent.

Signed-off-by: Eugen Hristev eugen.hristev@microchip.com Link: https://lkml.kernel.org/r/1568042692-11784-2-git-send-email-eugen.hristev@mi... Acked-by: Alexandre Belloni alexandre.belloni@bootlin.com Reviewed-by: Claudiu Beznea claudiu.beznea@microchip.com Signed-off-by: Stephen Boyd sboyd@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/clk/at91/clk-main.c | 10 +++++++--- 1 file changed, 7 insertions(+), 3 deletions(-)

diff --git a/drivers/clk/at91/clk-main.c b/drivers/clk/at91/clk-main.c index c813c27f2e58c..2f97a843d6d6b 100644 --- a/drivers/clk/at91/clk-main.c +++ b/drivers/clk/at91/clk-main.c @@ -27,6 +27,10 @@

#define MOR_KEY_MASK (0xff << 16)

+#define clk_main_parent_select(s) (((s) & \ + (AT91_PMC_MOSCEN | \ + AT91_PMC_OSCBYPASS)) ? 1 : 0) + struct clk_main_osc { struct clk_hw hw; struct regmap *regmap; @@ -119,7 +123,7 @@ static int clk_main_osc_is_prepared(struct clk_hw *hw)

regmap_read(regmap, AT91_PMC_SR, &status);

- return (status & AT91_PMC_MOSCS) && (tmp & AT91_PMC_MOSCEN); + return (status & AT91_PMC_MOSCS) && clk_main_parent_select(tmp); }

static const struct clk_ops main_osc_ops = { @@ -530,7 +534,7 @@ static u8 clk_sam9x5_main_get_parent(struct clk_hw *hw)

regmap_read(clkmain->regmap, AT91_CKGR_MOR, &status);

- return status & AT91_PMC_MOSCEN ? 1 : 0; + return clk_main_parent_select(status); }

static const struct clk_ops sam9x5_main_ops = { @@ -572,7 +576,7 @@ at91_clk_register_sam9x5_main(struct regmap *regmap, clkmain->hw.init = &init; clkmain->regmap = regmap; regmap_read(clkmain->regmap, AT91_CKGR_MOR, &status); - clkmain->parent = status & AT91_PMC_MOSCEN ? 1 : 0; + clkmain->parent = clk_main_parent_select(status);

hw = &clkmain->hw; ret = clk_hw_register(NULL, &clkmain->hw);

From: Jorge Ramirez-Ortiz jorge.ramirez-ortiz@linaro.org

[ Upstream commit 78c86458a440ff356073c21b568cb58ddb67b82b ]

There is clock controller functionality in the APCS hardware block of qcs404 devices similar to msm8916.

Co-developed-by: Niklas Cassel niklas.cassel@linaro.org Signed-off-by: Niklas Cassel niklas.cassel@linaro.org Signed-off-by: Jorge Ramirez-Ortiz jorge.ramirez-ortiz@linaro.org Reviewed-by: Bjorn Andersson bjorn.andersson@linaro.org Reviewed-by: Stephen Boyd sboyd@kernel.org Signed-off-by: Jassi Brar jaswinder.singh@linaro.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/mailbox/qcom-apcs-ipc-mailbox.c | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/drivers/mailbox/qcom-apcs-ipc-mailbox.c b/drivers/mailbox/qcom-apcs-ipc-mailbox.c index 333ed4a9d4b8f..5255dcb551a78 100644 --- a/drivers/mailbox/qcom-apcs-ipc-mailbox.c +++ b/drivers/mailbox/qcom-apcs-ipc-mailbox.c @@ -55,7 +55,6 @@ static const struct mbox_chan_ops qcom_apcs_ipc_ops = {

static int qcom_apcs_ipc_probe(struct platform_device *pdev) { - struct device_node *np = pdev->dev.of_node; struct qcom_apcs_ipc *apcs; struct regmap *regmap; struct resource *res; @@ -63,6 +62,11 @@ static int qcom_apcs_ipc_probe(struct platform_device *pdev) void __iomem *base; unsigned long i; int ret; + const struct of_device_id apcs_clk_match_table[] = { + { .compatible = "qcom,msm8916-apcs-kpss-global", }, + { .compatible = "qcom,qcs404-apcs-apps-global", }, + {} + };

apcs = devm_kzalloc(&pdev->dev, sizeof(*apcs), GFP_KERNEL); if (!apcs) @@ -97,7 +101,7 @@ static int qcom_apcs_ipc_probe(struct platform_device *pdev) return ret; }

- if (of_device_is_compatible(np, "qcom,msm8916-apcs-kpss-global")) { + if (of_match_device(apcs_clk_match_table, &pdev->dev)) { apcs->clk = platform_device_register_data(&pdev->dev, "qcom-apcs-msm8916-clk", -1, NULL, 0);

From: Bart Van Assche bvanassche@acm.org

[ Upstream commit dccc96abfb21dc19d69e707c38c8ba439bba7160 ]

The data structure used for log messages is so large that it can cause a boot failure. Since allocations from that data structure can fail anyway, use kmalloc() / kfree() instead of that data structure.

See also https://bugzilla.kernel.org/show_bug.cgi?id=204119. See also commit ded85c193a39 ("scsi: Implement per-cpu logging buffer") # v4.0.

Reported-by: Jan Palus jpalus@fastmail.com Cc: Christoph Hellwig hch@lst.de Cc: Hannes Reinecke hare@suse.com Cc: Johannes Thumshirn jthumshirn@suse.de Cc: Ming Lei ming.lei@redhat.com Cc: Jan Palus jpalus@fastmail.com Signed-off-by: Bart Van Assche bvanassche@acm.org Signed-off-by: Martin K. Petersen martin.petersen@oracle.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/scsi/scsi_logging.c | 48 +++---------------------------------- include/scsi/scsi_dbg.h | 2 -- 2 files changed, 3 insertions(+), 47 deletions(-)

diff --git a/drivers/scsi/scsi_logging.c b/drivers/scsi/scsi_logging.c index bd70339c1242e..03d9855a6afd7 100644 --- a/drivers/scsi/scsi_logging.c +++ b/drivers/scsi/scsi_logging.c @@ -16,57 +16,15 @@ #include <scsi/scsi_eh.h> #include <scsi/scsi_dbg.h>

-#define SCSI_LOG_SPOOLSIZE 4096 - -#if (SCSI_LOG_SPOOLSIZE / SCSI_LOG_BUFSIZE) > BITS_PER_LONG -#warning SCSI logging bitmask too large -#endif - -struct scsi_log_buf { - char buffer[SCSI_LOG_SPOOLSIZE]; - unsigned long map; -}; - -static DEFINE_PER_CPU(struct scsi_log_buf, scsi_format_log); - static char *scsi_log_reserve_buffer(size_t *len) { - struct scsi_log_buf *buf; - unsigned long map_bits = sizeof(buf->buffer) / SCSI_LOG_BUFSIZE; - unsigned long idx = 0; - - preempt_disable(); - buf = this_cpu_ptr(&scsi_format_log); - idx = find_first_zero_bit(&buf->map, map_bits); - if (likely(idx < map_bits)) { - while (test_and_set_bit(idx, &buf->map)) { - idx = find_next_zero_bit(&buf->map, map_bits, idx); - if (idx >= map_bits) - break; - } - } - if (WARN_ON(idx >= map_bits)) { - preempt_enable(); - return NULL; - } - *len = SCSI_LOG_BUFSIZE; - return buf->buffer + idx * SCSI_LOG_BUFSIZE; + *len = 128; + return kmalloc(*len, GFP_ATOMIC); }

static void scsi_log_release_buffer(char *bufptr) { - struct scsi_log_buf *buf; - unsigned long idx; - int ret; - - buf = this_cpu_ptr(&scsi_format_log); - if (bufptr >= buf->buffer && - bufptr < buf->buffer + SCSI_LOG_SPOOLSIZE) { - idx = (bufptr - buf->buffer) / SCSI_LOG_BUFSIZE; - ret = test_and_clear_bit(idx, &buf->map); - WARN_ON(!ret); - } - preempt_enable(); + kfree(bufptr); }

static inline const char *scmd_name(const struct scsi_cmnd *scmd) diff --git a/include/scsi/scsi_dbg.h b/include/scsi/scsi_dbg.h index e03bd9d41fa8f..7b196d2346264 100644 --- a/include/scsi/scsi_dbg.h +++ b/include/scsi/scsi_dbg.h @@ -6,8 +6,6 @@ struct scsi_cmnd; struct scsi_device; struct scsi_sense_hdr;

-#define SCSI_LOG_BUFSIZE 128 - extern void scsi_print_command(struct scsi_cmnd *); extern size_t __scsi_format_command(char *, size_t, const unsigned char *, size_t);

From: "zhangyi (F)" yi.zhang@huawei.com

[ Upstream commit 7727ae52975d4f4ef7ff69ed8e6e25f6a4168158 ]

Remount process will release system zone which was allocated before if "noblock_validity" is specified. If we mount an ext4 file system to two mountpoints with default mount options, and then remount one of them with "noblock_validity", it may trigger a use after free problem when someone accessing the other one.

# mount /dev/sda foo # mount /dev/sda bar

User access mountpoint "foo" | Remount mountpoint "bar" | ext4_map_blocks() | ext4_remount() check_block_validity() | ext4_setup_system_zone() ext4_data_block_valid() | ext4_release_system_zone() | free system_blks rb nodes access system_blks rb nodes | trigger use after free |

This problem can also be reproduced by one mountpint, At the same time, add_system_zone() can get called during remount as well so there can be racing ext4_data_block_valid() reading the rbtree at the same time.

This patch add RCU to protect system zone from releasing or building when doing a remount which inverse current "noblock_validity" mount option. It assign the rbtree after the whole tree was complete and do actual freeing after rcu grace period, avoid any intermediate state.

Reported-by: syzbot+1e470567330b7ad711d5@syzkaller.appspotmail.com Signed-off-by: zhangyi (F) yi.zhang@huawei.com Signed-off-by: Theodore Ts'o tytso@mit.edu Reviewed-by: Jan Kara jack@suse.cz Signed-off-by: Sasha Levin sashal@kernel.org --- fs/ext4/block_validity.c | 189 ++++++++++++++++++++++++++++----------- fs/ext4/ext4.h | 10 ++- 2 files changed, 147 insertions(+), 52 deletions(-)

diff --git a/fs/ext4/block_validity.c b/fs/ext4/block_validity.c index e8e27cdc2f677..7edc8172c53ad 100644 --- a/fs/ext4/block_validity.c +++ b/fs/ext4/block_validity.c @@ -38,6 +38,7 @@ int __init ext4_init_system_zone(void)

void ext4_exit_system_zone(void) { + rcu_barrier(); kmem_cache_destroy(ext4_system_zone_cachep); }

@@ -49,17 +50,26 @@ static inline int can_merge(struct ext4_system_zone *entry1, return 0; }

+static void release_system_zone(struct ext4_system_blocks *system_blks) +{ + struct ext4_system_zone *entry, *n; + + rbtree_postorder_for_each_entry_safe(entry, n, + &system_blks->root, node) + kmem_cache_free(ext4_system_zone_cachep, entry); +} + /* * Mark a range of blocks as belonging to the "system zone" --- that * is, filesystem metadata blocks which should never be used by * inodes. */ -static int add_system_zone(struct ext4_sb_info *sbi, +static int add_system_zone(struct ext4_system_blocks *system_blks, ext4_fsblk_t start_blk, unsigned int count) { struct ext4_system_zone *new_entry = NULL, *entry; - struct rb_node **n = &sbi->system_blks.rb_node, *node; + struct rb_node **n = &system_blks->root.rb_node, *node; struct rb_node *parent = NULL, *new_node = NULL;

while (*n) { @@ -91,7 +101,7 @@ static int add_system_zone(struct ext4_sb_info *sbi, new_node = &new_entry->node;

rb_link_node(new_node, parent, n); - rb_insert_color(new_node, &sbi->system_blks); + rb_insert_color(new_node, &system_blks->root); }

/* Can we merge to the left? */ @@ -101,7 +111,7 @@ static int add_system_zone(struct ext4_sb_info *sbi, if (can_merge(entry, new_entry)) { new_entry->start_blk = entry->start_blk; new_entry->count += entry->count; - rb_erase(node, &sbi->system_blks); + rb_erase(node, &system_blks->root); kmem_cache_free(ext4_system_zone_cachep, entry); } } @@ -112,7 +122,7 @@ static int add_system_zone(struct ext4_sb_info *sbi, entry = rb_entry(node, struct ext4_system_zone, node); if (can_merge(new_entry, entry)) { new_entry->count += entry->count; - rb_erase(node, &sbi->system_blks); + rb_erase(node, &system_blks->root); kmem_cache_free(ext4_system_zone_cachep, entry); } } @@ -126,7 +136,7 @@ static void debug_print_tree(struct ext4_sb_info *sbi) int first = 1;

printk(KERN_INFO "System zones: "); - node = rb_first(&sbi->system_blks); + node = rb_first(&sbi->system_blks->root); while (node) { entry = rb_entry(node, struct ext4_system_zone, node); printk(KERN_CONT "%s%llu-%llu", first ? "" : ", ", @@ -137,7 +147,47 @@ static void debug_print_tree(struct ext4_sb_info *sbi) printk(KERN_CONT "\n"); }

-static int ext4_protect_reserved_inode(struct super_block *sb, u32 ino) +/* + * Returns 1 if the passed-in block region (start_blk, + * start_blk+count) is valid; 0 if some part of the block region + * overlaps with filesystem metadata blocks. + */ +static int ext4_data_block_valid_rcu(struct ext4_sb_info *sbi, + struct ext4_system_blocks *system_blks, + ext4_fsblk_t start_blk, + unsigned int count) +{ + struct ext4_system_zone *entry; + struct rb_node *n; + + if ((start_blk <= le32_to_cpu(sbi->s_es->s_first_data_block)) || + (start_blk + count < start_blk) || + (start_blk + count > ext4_blocks_count(sbi->s_es))) { + sbi->s_es->s_last_error_block = cpu_to_le64(start_blk); + return 0; + } + + if (system_blks == NULL) + return 1; + + n = system_blks->root.rb_node; + while (n) { + entry = rb_entry(n, struct ext4_system_zone, node); + if (start_blk + count - 1 < entry->start_blk) + n = n->rb_left; + else if (start_blk >= (entry->start_blk + entry->count)) + n = n->rb_right; + else { + sbi->s_es->s_last_error_block = cpu_to_le64(start_blk); + return 0; + } + } + return 1; +} + +static int ext4_protect_reserved_inode(struct super_block *sb, + struct ext4_system_blocks *system_blks, + u32 ino) { struct inode *inode; struct ext4_sb_info *sbi = EXT4_SB(sb); @@ -163,14 +213,15 @@ static int ext4_protect_reserved_inode(struct super_block *sb, u32 ino) if (n == 0) { i++; } else { - if (!ext4_data_block_valid(sbi, map.m_pblk, n)) { + if (!ext4_data_block_valid_rcu(sbi, system_blks, + map.m_pblk, n)) { ext4_error(sb, "blocks %llu-%llu from inode %u " "overlap system zone", map.m_pblk, map.m_pblk + map.m_len - 1, ino); err = -EFSCORRUPTED; break; } - err = add_system_zone(sbi, map.m_pblk, n); + err = add_system_zone(system_blks, map.m_pblk, n); if (err < 0) break; i += n; @@ -180,93 +231,129 @@ static int ext4_protect_reserved_inode(struct super_block *sb, u32 ino) return err; }

+static void ext4_destroy_system_zone(struct rcu_head *rcu) +{ + struct ext4_system_blocks *system_blks; + + system_blks = container_of(rcu, struct ext4_system_blocks, rcu); + release_system_zone(system_blks); + kfree(system_blks); +} + +/* + * Build system zone rbtree which is used for block validity checking. + * + * The update of system_blks pointer in this function is protected by + * sb->s_umount semaphore. However we have to be careful as we can be + * racing with ext4_data_block_valid() calls reading system_blks rbtree + * protected only by RCU. That's why we first build the rbtree and then + * swap it in place. + */ int ext4_setup_system_zone(struct super_block *sb) { ext4_group_t ngroups = ext4_get_groups_count(sb); struct ext4_sb_info *sbi = EXT4_SB(sb); + struct ext4_system_blocks *system_blks; struct ext4_group_desc *gdp; ext4_group_t i; int flex_size = ext4_flex_bg_size(sbi); int ret;

if (!test_opt(sb, BLOCK_VALIDITY)) { - if (sbi->system_blks.rb_node) + if (sbi->system_blks) ext4_release_system_zone(sb); return 0; } - if (sbi->system_blks.rb_node) + if (sbi->system_blks) return 0;

+ system_blks = kzalloc(sizeof(*system_blks), GFP_KERNEL); + if (!system_blks) + return -ENOMEM; + for (i=0; i < ngroups; i++) { if (ext4_bg_has_super(sb, i) && ((i < 5) || ((i % flex_size) == 0))) - add_system_zone(sbi, ext4_group_first_block_no(sb, i), + add_system_zone(system_blks, + ext4_group_first_block_no(sb, i), ext4_bg_num_gdb(sb, i) + 1); gdp = ext4_get_group_desc(sb, i, NULL); - ret = add_system_zone(sbi, ext4_block_bitmap(sb, gdp), 1); + ret = add_system_zone(system_blks, + ext4_block_bitmap(sb, gdp), 1); if (ret) - return ret; - ret = add_system_zone(sbi, ext4_inode_bitmap(sb, gdp), 1); + goto err; + ret = add_system_zone(system_blks, + ext4_inode_bitmap(sb, gdp), 1); if (ret) - return ret; - ret = add_system_zone(sbi, ext4_inode_table(sb, gdp), + goto err; + ret = add_system_zone(system_blks, + ext4_inode_table(sb, gdp), sbi->s_itb_per_group); if (ret) - return ret; + goto err; } if (ext4_has_feature_journal(sb) && sbi->s_es->s_journal_inum) { - ret = ext4_protect_reserved_inode(sb, + ret = ext4_protect_reserved_inode(sb, system_blks, le32_to_cpu(sbi->s_es->s_journal_inum)); if (ret) - return ret; + goto err; }

+ /* + * System blks rbtree complete, announce it once to prevent racing + * with ext4_data_block_valid() accessing the rbtree at the same + * time. + */ + rcu_assign_pointer(sbi->system_blks, system_blks); + if (test_opt(sb, DEBUG)) debug_print_tree(sbi); return 0; +err: + release_system_zone(system_blks); + kfree(system_blks); + return ret; }

-/* Called when the filesystem is unmounted */ +/* + * Called when the filesystem is unmounted or when remounting it with + * noblock_validity specified. + * + * The update of system_blks pointer in this function is protected by + * sb->s_umount semaphore. However we have to be careful as we can be + * racing with ext4_data_block_valid() calls reading system_blks rbtree + * protected only by RCU. So we first clear the system_blks pointer and + * then free the rbtree only after RCU grace period expires. + */ void ext4_release_system_zone(struct super_block *sb) { - struct ext4_system_zone *entry, *n; + struct ext4_system_blocks *system_blks;

- rbtree_postorder_for_each_entry_safe(entry, n, - &EXT4_SB(sb)->system_blks, node) - kmem_cache_free(ext4_system_zone_cachep, entry); + system_blks = rcu_dereference_protected(EXT4_SB(sb)->system_blks, + lockdep_is_held(&sb->s_umount)); + rcu_assign_pointer(EXT4_SB(sb)->system_blks, NULL);

- EXT4_SB(sb)->system_blks = RB_ROOT; + if (system_blks) + call_rcu(&system_blks->rcu, ext4_destroy_system_zone); }

-/* - * Returns 1 if the passed-in block region (start_blk, - * start_blk+count) is valid; 0 if some part of the block region - * overlaps with filesystem metadata blocks. - */ int ext4_data_block_valid(struct ext4_sb_info *sbi, ext4_fsblk_t start_blk, unsigned int count) { - struct ext4_system_zone *entry; - struct rb_node *n = sbi->system_blks.rb_node; + struct ext4_system_blocks *system_blks; + int ret;

- if ((start_blk <= le32_to_cpu(sbi->s_es->s_first_data_block)) || - (start_blk + count < start_blk) || - (start_blk + count > ext4_blocks_count(sbi->s_es))) { - sbi->s_es->s_last_error_block = cpu_to_le64(start_blk); - return 0; - } - while (n) { - entry = rb_entry(n, struct ext4_system_zone, node); - if (start_blk + count - 1 < entry->start_blk) - n = n->rb_left; - else if (start_blk >= (entry->start_blk + entry->count)) - n = n->rb_right; - else { - sbi->s_es->s_last_error_block = cpu_to_le64(start_blk); - return 0; - } - } - return 1; + /* + * Lock the system zone to prevent it being released concurrently + * when doing a remount which inverse current "[no]block_validity" + * mount option. + */ + rcu_read_lock(); + system_blks = rcu_dereference(sbi->system_blks); + ret = ext4_data_block_valid_rcu(sbi, system_blks, start_blk, + count); + rcu_read_unlock(); + return ret; }

int ext4_check_blockref(const char *function, unsigned int line, diff --git a/fs/ext4/ext4.h b/fs/ext4/ext4.h index 1ee51d3a978ad..f8456a423c4ea 100644 --- a/fs/ext4/ext4.h +++ b/fs/ext4/ext4.h @@ -194,6 +194,14 @@ struct ext4_map_blocks { unsigned int m_flags; };

+/* + * Block validity checking, system zone rbtree. + */ +struct ext4_system_blocks { + struct rb_root root; + struct rcu_head rcu; +}; + /* * Flags for ext4_io_end->flags */ @@ -1409,7 +1417,7 @@ struct ext4_sb_info { int s_jquota_fmt; /* Format of quota to use */ #endif unsigned int s_want_extra_isize; /* New inodes should reserve # bytes */ - struct rb_root system_blks; + struct ext4_system_blocks __rcu *system_blks;

#ifdef EXTENTS_STATS /* ext4 extents stats */