[PATCH AUTOSEL 5.10 01/19] ARM: dts: ls1021a-tsn: update RGMII delays for sja1105 switch
From: Vladimir Oltean vladimir.oltean@nxp.com
[ Upstream commit e691f9282a89e24a8e87cdb91a181c6283ee5124 ]
In the new behavior, the sja1105 driver expects there to be explicit RGMII delays present on the fixed-link ports, otherwise it will complain that it falls back to legacy behavior, which is to apply RGMII delays incorrectly derived from the phy-mode string.
In this case, the legacy behavior of the driver is to not apply delays in any direction (mostly because the SJA1105T can't do that, so this board uses PCB traces). To preserve that but also silence the driver, use explicit delays of 0 ns. The delay information from the phy-mode is ignored by new kernels (it's still RGMII as long as it's "rgmii*" something), and the explicit {rx,tx}-internal-delay-ps properties are ignored by old kernels, so the change works both ways.
Signed-off-by: Vladimir Oltean vladimir.oltean@nxp.com Reviewed-by: Florian Fainelli f.fainelli@gmail.com Signed-off-by: Shawn Guo shawnguo@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- arch/arm/boot/dts/ls1021a-tsn.dts | 2 ++ 1 file changed, 2 insertions(+)
diff --git a/arch/arm/boot/dts/ls1021a-tsn.dts b/arch/arm/boot/dts/ls1021a-tsn.dts index aca78b5eddf20..194748737724c 100644 --- a/arch/arm/boot/dts/ls1021a-tsn.dts +++ b/arch/arm/boot/dts/ls1021a-tsn.dts @@ -90,6 +90,8 @@ port@4 { /* Internal port connected to eth2 */ ethernet = <&enet2>; phy-mode = "rgmii"; + rx-internal-delay-ps = <0>; + tx-internal-delay-ps = <0>; reg = <4>;
fixed-link {
From: "Ivan T. Ivanov" iivanov@suse.de
[ Upstream commit 423e85e97aaf69e5198bbec6811e3825c8b5019a ]
This fixes a potential kernel panic on memcpy when FORTIFY_SOURCE is enabled. Because memory is iomem use appropriate function for accessing it.
Signed-off-by: Ivan T. Ivanov iivanov@suse.de Link: https://lore.kernel.org/r/20211116084616.24811-1-iivanov@suse.de Signed-off-by: Heiko Stuebner heiko@sntech.de Signed-off-by: Sasha Levin sashal@kernel.org --- arch/arm/mach-rockchip/platsmp.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/mach-rockchip/platsmp.c b/arch/arm/mach-rockchip/platsmp.c index d60856898d97a..5ec58d004b7de 100644 --- a/arch/arm/mach-rockchip/platsmp.c +++ b/arch/arm/mach-rockchip/platsmp.c @@ -189,7 +189,7 @@ static int __init rockchip_smp_prepare_sram(struct device_node *node) rockchip_boot_fn = __pa_symbol(secondary_startup);
/* copy the trampoline to sram, that runs during startup of the core */ - memcpy(sram_base_addr, &rockchip_secondary_trampoline, trampoline_sz); + memcpy_toio(sram_base_addr, &rockchip_secondary_trampoline, trampoline_sz); flush_cache_all(); outer_clean_range(0, trampoline_sz);
From: Xing Song xing.song@mediatek.com
[ Upstream commit 942bd1070c3a39d1302fc5db73d60c86e3033c81 ]
Mesh forwarding requires that the fwd_skb->dev is set up for TX handling, otherwise the following warning will be generated, so set it up for the pending frames.
[ 72.835674 ] WARNING: CPU: 0 PID: 1193 at __skb_flow_dissect+0x284/0x1298 [ 72.842379 ] Modules linked in: ksmbd pppoe ppp_async l2tp_ppp ... [ 72.962020 ] CPU: 0 PID: 1193 Comm: kworker/u5:1 Tainted: P S 5.4.137 #0 [ 72.969938 ] Hardware name: MT7622_MT7531 RFB (DT) [ 72.974659 ] Workqueue: napi_workq napi_workfn [ 72.979025 ] pstate: 60000005 (nZCv daif -PAN -UAO) [ 72.983822 ] pc : __skb_flow_dissect+0x284/0x1298 [ 72.988444 ] lr : __skb_flow_dissect+0x54/0x1298 [ 72.992977 ] sp : ffffffc010c738c0 [ 72.996293 ] x29: ffffffc010c738c0 x28: 0000000000000000 [ 73.001615 ] x27: 000000000000ffc2 x26: ffffff800c2eb818 [ 73.006937 ] x25: ffffffc010a987c8 x24: 00000000000000ce [ 73.012259 ] x23: ffffffc010c73a28 x22: ffffffc010a99c60 [ 73.017581 ] x21: 000000000000ffc2 x20: ffffff80094da800 [ 73.022903 ] x19: 0000000000000000 x18: 0000000000000014 [ 73.028226 ] x17: 00000000084d16af x16: 00000000d1fc0bab [ 73.033548 ] x15: 00000000715f6034 x14: 000000009dbdd301 [ 73.038870 ] x13: 00000000ea4dcbc3 x12: 0000000000000040 [ 73.044192 ] x11: 000000000eb00ff0 x10: 0000000000000000 [ 73.049513 ] x9 : 000000000eb00073 x8 : 0000000000000088 [ 73.054834 ] x7 : 0000000000000000 x6 : 0000000000000001 [ 73.060155 ] x5 : 0000000000000000 x4 : 0000000000000000 [ 73.065476 ] x3 : ffffffc010a98000 x2 : 0000000000000000 [ 73.070797 ] x1 : 0000000000000000 x0 : 0000000000000000 [ 73.076120 ] Call trace: [ 73.078572 ] __skb_flow_dissect+0x284/0x1298 [ 73.082846 ] __skb_get_hash+0x7c/0x228 [ 73.086629 ] ieee80211_txq_may_transmit+0x7fc/0x17b8 [mac80211] [ 73.092564 ] ieee80211_tx_prepare_skb+0x20c/0x268 [mac80211] [ 73.098238 ] ieee80211_tx_pending+0x144/0x330 [mac80211] [ 73.103560 ] tasklet_action_common.isra.16+0xb4/0x158 [ 73.108618 ] tasklet_action+0x2c/0x38 [ 73.112286 ] __do_softirq+0x168/0x3b0 [ 73.115954 ] do_softirq.part.15+0x88/0x98 [ 73.119969 ] __local_bh_enable_ip+0xb0/0xb8 [ 73.124156 ] napi_workfn+0x58/0x90 [ 73.127565 ] process_one_work+0x20c/0x478 [ 73.131579 ] worker_thread+0x50/0x4f0 [ 73.135249 ] kthread+0x124/0x128 [ 73.138484 ] ret_from_fork+0x10/0x1c
Signed-off-by: Xing Song xing.song@mediatek.com Tested-By: Frank Wunderlich frank-w@public-files.de Link: https://lore.kernel.org/r/20211123033123.2684-1-xing.song@mediatek.com Signed-off-by: Johannes Berg johannes.berg@intel.com Signed-off-by: Sasha Levin sashal@kernel.org --- net/mac80211/rx.c | 1 + 1 file changed, 1 insertion(+)
diff --git a/net/mac80211/rx.c b/net/mac80211/rx.c index 6a24431b90095..b4de573730b26 100644 --- a/net/mac80211/rx.c +++ b/net/mac80211/rx.c @@ -2937,6 +2937,7 @@ ieee80211_rx_h_mesh_fwding(struct ieee80211_rx_data *rx) if (!fwd_skb) goto out;
+ fwd_skb->dev = sdata->dev; fwd_hdr = (struct ieee80211_hdr *) fwd_skb->data; fwd_hdr->frame_control &= ~cpu_to_le16(IEEE80211_FCTL_RETRY); info = IEEE80211_SKB_CB(fwd_skb);
From: Ahmed Zaki anzaki@gmail.com
[ Upstream commit 8f9dcc29566626f683843ccac6113a12208315ca ]
The following is from a system that went OOM due to a memory leak:
wlan0: Allocated STA 74:83:c2:64:0b:87 wlan0: Allocated STA 74:83:c2:64:0b:87 wlan0: IBSS finish 74:83:c2:64:0b:87 (---from ieee80211_ibss_add_sta) wlan0: Adding new IBSS station 74:83:c2:64:0b:87 wlan0: moving STA 74:83:c2:64:0b:87 to state 2 wlan0: moving STA 74:83:c2:64:0b:87 to state 3 wlan0: Inserted STA 74:83:c2:64:0b:87 wlan0: IBSS finish 74:83:c2:64:0b:87 (---from ieee80211_ibss_work) wlan0: Adding new IBSS station 74:83:c2:64:0b:87 wlan0: moving STA 74:83:c2:64:0b:87 to state 2 wlan0: moving STA 74:83:c2:64:0b:87 to state 3 . . wlan0: expiring inactive not authorized STA 74:83:c2:64:0b:87 wlan0: moving STA 74:83:c2:64:0b:87 to state 2 wlan0: moving STA 74:83:c2:64:0b:87 to state 1 wlan0: Removed STA 74:83:c2:64:0b:87 wlan0: Destroyed STA 74:83:c2:64:0b:87
The ieee80211_ibss_finish_sta() is called twice on the same STA from 2 different locations. On the second attempt, the allocated STA is not destroyed creating a kernel memory leak.
This is happening because sta_info_insert_finish() does not call sta_info_free() the second time when the STA already exists (returns -EEXIST). Note that the caller sta_info_insert_rcu() assumes STA is destroyed upon errors.
Same fix is applied to -ENOMEM.
Signed-off-by: Ahmed Zaki anzaki@gmail.com Link: https://lore.kernel.org/r/20211002145329.3125293-1-anzaki@gmail.com [change the error path label to use the existing code] Signed-off-by: Johannes Berg johannes.berg@intel.com Signed-off-by: Sasha Levin sashal@kernel.org --- net/mac80211/sta_info.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)
diff --git a/net/mac80211/sta_info.c b/net/mac80211/sta_info.c index e18c3855f6161..461c03737da8d 100644 --- a/net/mac80211/sta_info.c +++ b/net/mac80211/sta_info.c @@ -645,13 +645,13 @@ static int sta_info_insert_finish(struct sta_info *sta) __acquires(RCU) /* check if STA exists already */ if (sta_info_get_bss(sdata, sta->sta.addr)) { err = -EEXIST; - goto out_err; + goto out_cleanup; }
sinfo = kzalloc(sizeof(struct station_info), GFP_KERNEL); if (!sinfo) { err = -ENOMEM; - goto out_err; + goto out_cleanup; }
local->num_sta++; @@ -707,8 +707,8 @@ static int sta_info_insert_finish(struct sta_info *sta) __acquires(RCU) out_drop_sta: local->num_sta--; synchronize_net(); + out_cleanup: cleanup_single_sta(sta); - out_err: mutex_unlock(&local->sta_mtx); kfree(sinfo); rcu_read_lock();
From: Finn Behrens me@kloenk.dev
[ Upstream commit 1eda919126b420fee6b8d546f7f728fbbd4b8f11 ]
Reload the regdom when the regulatory db is reloaded. Otherwise, the user had to change the regulatoy domain to a different one and then reset it to the correct one to have a new regulatory db take effect after a reload.
Signed-off-by: Finn Behrens fin@nyantec.com Link: https://lore.kernel.org/r/YaIIZfxHgqc/UTA7@gimli.kloenk.dev [edit commit message] Signed-off-by: Johannes Berg johannes.berg@intel.com Signed-off-by: Sasha Levin sashal@kernel.org --- include/net/regulatory.h | 1 + net/wireless/reg.c | 27 +++++++++++++++++++++++++-- 2 files changed, 26 insertions(+), 2 deletions(-)
diff --git a/include/net/regulatory.h b/include/net/regulatory.h index 47f06f6f5a67c..0cf9335431e07 100644 --- a/include/net/regulatory.h +++ b/include/net/regulatory.h @@ -83,6 +83,7 @@ struct regulatory_request { enum nl80211_dfs_regions dfs_region; bool intersect; bool processed; + bool reload; enum environment_cap country_ie_env; struct list_head list; }; diff --git a/net/wireless/reg.c b/net/wireless/reg.c index a04fdfb35f070..341c88972aed1 100644 --- a/net/wireless/reg.c +++ b/net/wireless/reg.c @@ -133,6 +133,7 @@ static u32 reg_is_indoor_portid;
static void restore_regulatory_settings(bool reset_user, bool cached); static void print_regdomain(const struct ieee80211_regdomain *rd); +static void reg_process_hint(struct regulatory_request *reg_request);
static const struct ieee80211_regdomain *get_cfg80211_regdom(void) { @@ -1079,6 +1080,8 @@ int reg_reload_regdb(void) const struct firmware *fw; void *db; int err; + const struct ieee80211_regdomain *current_regdomain; + struct regulatory_request *request;
err = request_firmware(&fw, "regulatory.db", ®_pdev->dev); if (err) @@ -1099,8 +1102,27 @@ int reg_reload_regdb(void) if (!IS_ERR_OR_NULL(regdb)) kfree(regdb); regdb = db; - rtnl_unlock();
+ /* reset regulatory domain */ + current_regdomain = get_cfg80211_regdom(); + + request = kzalloc(sizeof(*request), GFP_KERNEL); + if (!request) { + err = -ENOMEM; + goto out_unlock; + } + + request->wiphy_idx = WIPHY_IDX_INVALID; + request->alpha2[0] = current_regdomain->alpha2[0]; + request->alpha2[1] = current_regdomain->alpha2[1]; + request->initiator = NL80211_USER_REG_HINT_USER; + request->user_reg_hint_type = NL80211_USER_REG_HINT_USER; + request->reload = true; + + reg_process_hint(request); + +out_unlock: + rtnl_unlock(); out: release_firmware(fw); return err; @@ -2657,7 +2679,8 @@ reg_process_hint_user(struct regulatory_request *user_request)
treatment = __reg_process_hint_user(user_request); if (treatment == REG_REQ_IGNORE || - treatment == REG_REQ_ALREADY_SET) + (treatment == REG_REQ_ALREADY_SET && + !user_request->reload)) return REG_REQ_IGNORE;
user_request->intersect = treatment == REG_REQ_INTERSECT;
From: Arnd Bergmann arnd@arndb.de
[ Upstream commit efdbfa0ad03e764419378485d1b8f6e7706fb1a3 ]
The dependencies for LED configuration are highly inconsistent and too complicated at the moment. One of the results is a randconfig failure I get very rarely when LEDS_CLASS is in a loadable module, but the wireless core is built-in:
WARNING: unmet direct dependencies detected for MAC80211_LEDS Depends on [n]: NET [=y] && WIRELESS [=y] && MAC80211 [=y] && (LEDS_CLASS [=m]=y || LEDS_CLASS [=m]=MAC80211 [=y]) Selected by [m]: - IWLEGACY [=m] && NETDEVICES [=y] && WLAN [=y] && WLAN_VENDOR_INTEL [=y] - IWLWIFI_LEDS [=y] && NETDEVICES [=y] && WLAN [=y] && WLAN_VENDOR_INTEL [=y] && IWLWIFI [=m] && (LEDS_CLASS [=m]=y || LEDS_CLASS [=m]=IWLWIFI [=m]) && (IWLMVM [=m] || IWLDVM [=m])
aarch64-linux-ld: drivers/net/wireless/ath/ath5k/led.o: in function `ath5k_register_led': led.c:(.text+0x60): undefined reference to `led_classdev_register_ext' aarch64-linux-ld: drivers/net/wireless/ath/ath5k/led.o: in function `ath5k_unregister_leds': led.c:(.text+0x200): undefined reference to `led_classdev_unregister'
For iwlwifi, the dependency is wrong, since this config prevents the MAC80211_LEDS code from being part of a built-in MAC80211 driver.
For iwlegacy, this is worse because the driver tries to force-enable the other subsystems, which is both a layering violation and a bug because it will still fail with MAC80211=y and IWLEGACY=m, leading to LEDS_CLASS being a module as well.
The actual link failure in the ath5k driver is a result of MAC80211_LEDS being enabled but not usable. With the Kconfig logic fixed in the Intel drivers, the ath5k driver works as expected again.
Signed-off-by: Arnd Bergmann arnd@arndb.de Acked-by: Luca Coelho luciano.coelho@intel.com Signed-off-by: Kalle Valo kvalo@kernel.org Link: https://lore.kernel.org/r/20211204173848.873293-1-arnd@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/net/wireless/intel/iwlegacy/Kconfig | 4 ++-- drivers/net/wireless/intel/iwlwifi/Kconfig | 2 +- 2 files changed, 3 insertions(+), 3 deletions(-)
diff --git a/drivers/net/wireless/intel/iwlegacy/Kconfig b/drivers/net/wireless/intel/iwlegacy/Kconfig index 24fe3f63c3215..7eacc8e58ee14 100644 --- a/drivers/net/wireless/intel/iwlegacy/Kconfig +++ b/drivers/net/wireless/intel/iwlegacy/Kconfig @@ -2,14 +2,13 @@ config IWLEGACY tristate select FW_LOADER - select NEW_LEDS - select LEDS_CLASS select LEDS_TRIGGERS select MAC80211_LEDS
config IWL4965 tristate "Intel Wireless WiFi 4965AGN (iwl4965)" depends on PCI && MAC80211 + depends on LEDS_CLASS=y || LEDS_CLASS=MAC80211 select IWLEGACY help This option enables support for @@ -38,6 +37,7 @@ config IWL4965 config IWL3945 tristate "Intel PRO/Wireless 3945ABG/BG Network Connection (iwl3945)" depends on PCI && MAC80211 + depends on LEDS_CLASS=y || LEDS_CLASS=MAC80211 select IWLEGACY help Select to build the driver supporting the: diff --git a/drivers/net/wireless/intel/iwlwifi/Kconfig b/drivers/net/wireless/intel/iwlwifi/Kconfig index 1085afbefba87..418ae4f870ab7 100644 --- a/drivers/net/wireless/intel/iwlwifi/Kconfig +++ b/drivers/net/wireless/intel/iwlwifi/Kconfig @@ -47,7 +47,7 @@ if IWLWIFI
config IWLWIFI_LEDS bool - depends on LEDS_CLASS=y || LEDS_CLASS=IWLWIFI + depends on LEDS_CLASS=y || LEDS_CLASS=MAC80211 depends on IWLMVM || IWLDVM select LEDS_TRIGGERS select MAC80211_LEDS
From: Hangyu Hua hbh25y@gmail.com
[ Upstream commit bcd0f93353326954817a4f9fa55ec57fb38acbb0 ]
sock_hold(sk) is invoked in pep_sock_accept(), but __sock_put(sk) is not invoked in subsequent failure branches(pep_accept_conn() != 0).
Signed-off-by: Hangyu Hua hbh25y@gmail.com Link: https://lore.kernel.org/r/20211209082839.33985-1-hbh25y@gmail.com Signed-off-by: Jakub Kicinski kuba@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- net/phonet/pep.c | 1 + 1 file changed, 1 insertion(+)
diff --git a/net/phonet/pep.c b/net/phonet/pep.c index a1525916885ae..b4f90afb0638b 100644 --- a/net/phonet/pep.c +++ b/net/phonet/pep.c @@ -868,6 +868,7 @@ static struct sock *pep_sock_accept(struct sock *sk, int flags, int *errp,
err = pep_accept_conn(newsk, skb); if (err) { + __sock_put(sk); sock_put(newsk); newsk = NULL; goto drop;
From: Miaoqian Lin linmq006@gmail.com
[ Upstream commit ab8eb798ddabddb2944401bf31ead9671cb97d95 ]
The phy_attach() function does not return NULL. It returns error pointers.
Signed-off-by: Miaoqian Lin linmq006@gmail.com Acked-by: Florian Fainelli f.fainelli@gmail.com Signed-off-by: David S. Miller davem@davemloft.net Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/net/ethernet/broadcom/genet/bcmmii.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/net/ethernet/broadcom/genet/bcmmii.c b/drivers/net/ethernet/broadcom/genet/bcmmii.c index f9e91304d2327..2b67e335bc54e 100644 --- a/drivers/net/ethernet/broadcom/genet/bcmmii.c +++ b/drivers/net/ethernet/broadcom/genet/bcmmii.c @@ -557,9 +557,9 @@ static int bcmgenet_mii_pd_init(struct bcmgenet_priv *priv) * Internal or external PHY with MDIO access */ phydev = phy_attach(priv->dev, phy_name, pd->phy_interface); - if (!phydev) { + if (IS_ERR(phydev)) { dev_err(kdev, "failed to register PHY device\n"); - return -ENODEV; + return PTR_ERR(phydev); } } else { /*
From: John Garry john.garry@huawei.com
[ Upstream commit 2fe24343922e0428fb68674a4fae099171141bc7 ]
The driver supports a "direct" mode of operation, where the SMP req frame is directly copied into the command payload (and vice-versa for the SMP resp).
To get at the SMP req frame data in the scatterlist the driver uses phys_to_virt() on the DMA mapped memory dma_addr_t . This is broken, and subsequently crashes as follows when an IOMMU is enabled:
Unable to handle kernel paging request at virtual address ffff0000fcebfb00 ... pc : pm80xx_chip_smp_req+0x2d0/0x3d0 lr : pm80xx_chip_smp_req+0xac/0x3d0 pm80xx_chip_smp_req+0x2d0/0x3d0 pm8001_task_exec.constprop.0+0x368/0x520 pm8001_queue_command+0x1c/0x30 smp_execute_task_sg+0xdc/0x204 sas_discover_expander.part.0+0xac/0x6cc sas_discover_root_expander+0x8c/0x150 sas_discover_domain+0x3ac/0x6a0 process_one_work+0x1d0/0x354 worker_thread+0x13c/0x470 kthread+0x17c/0x190 ret_from_fork+0x10/0x20 Code: 371806e1 910006d6 6b16033f 54000249 (38766b05) ---[ end trace b91d59aaee98ea2d ]--- note: kworker/u192:0[7] exited with preempt_count 1
Instead use kmap_atomic().
-- Difference to v1: - use kmap_atomic() in both locations Difference to v2: - add whitespace around arithmetic (Damien)
Link: https://lore.kernel.org/r/1639390248-213603-1-git-send-email-john.garry@huaw... Reviewed-by: Damien Le Moal damien.lemoal@opensource.wdc.com Signed-off-by: John Garry john.garry@huawei.com Signed-off-by: Martin K. Petersen martin.petersen@oracle.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/scsi/pm8001/pm80xx_hwi.c | 38 ++++++++++++++++++-------------- 1 file changed, 21 insertions(+), 17 deletions(-)
diff --git a/drivers/scsi/pm8001/pm80xx_hwi.c b/drivers/scsi/pm8001/pm80xx_hwi.c index a203a4fc2674a..4badd2ad2a460 100644 --- a/drivers/scsi/pm8001/pm80xx_hwi.c +++ b/drivers/scsi/pm8001/pm80xx_hwi.c @@ -2965,7 +2965,6 @@ mpi_smp_completion(struct pm8001_hba_info *pm8001_ha, void *piomb) struct smp_completion_resp *psmpPayload; struct task_status_struct *ts; struct pm8001_device *pm8001_dev; - char *pdma_respaddr = NULL;
psmpPayload = (struct smp_completion_resp *)(piomb + 4); status = le32_to_cpu(psmpPayload->status); @@ -2992,19 +2991,23 @@ mpi_smp_completion(struct pm8001_hba_info *pm8001_ha, void *piomb) if (pm8001_dev) atomic_dec(&pm8001_dev->running_req); if (pm8001_ha->smp_exp_mode == SMP_DIRECT) { + struct scatterlist *sg_resp = &t->smp_task.smp_resp; + u8 *payload; + void *to; + pm8001_dbg(pm8001_ha, IO, "DIRECT RESPONSE Length:%d\n", param); - pdma_respaddr = (char *)(phys_to_virt(cpu_to_le64 - ((u64)sg_dma_address - (&t->smp_task.smp_resp)))); + to = kmap_atomic(sg_page(sg_resp)); + payload = to + sg_resp->offset; for (i = 0; i < param; i++) { - *(pdma_respaddr+i) = psmpPayload->_r_a[i]; + *(payload + i) = psmpPayload->_r_a[i]; pm8001_dbg(pm8001_ha, IO, "SMP Byte%d DMA data 0x%x psmp 0x%x\n", - i, *(pdma_respaddr + i), + i, *(payload + i), psmpPayload->_r_a[i]); } + kunmap_atomic(to); } break; case IO_ABORTED: @@ -4133,14 +4136,14 @@ static int pm80xx_chip_smp_req(struct pm8001_hba_info *pm8001_ha, struct sas_task *task = ccb->task; struct domain_device *dev = task->dev; struct pm8001_device *pm8001_dev = dev->lldd_dev; - struct scatterlist *sg_req, *sg_resp; + struct scatterlist *sg_req, *sg_resp, *smp_req; u32 req_len, resp_len; struct smp_req smp_cmd; u32 opc; struct inbound_queue_table *circularQ; - char *preq_dma_addr = NULL; - __le64 tmp_addr; u32 i, length; + u8 *payload; + u8 *to;
memset(&smp_cmd, 0, sizeof(smp_cmd)); /* @@ -4177,8 +4180,9 @@ static int pm80xx_chip_smp_req(struct pm8001_hba_info *pm8001_ha, pm8001_ha->smp_exp_mode = SMP_INDIRECT;
- tmp_addr = cpu_to_le64((u64)sg_dma_address(&task->smp_task.smp_req)); - preq_dma_addr = (char *)phys_to_virt(tmp_addr); + smp_req = &task->smp_task.smp_req; + to = kmap_atomic(sg_page(smp_req)); + payload = to + smp_req->offset;
/* INDIRECT MODE command settings. Use DMA */ if (pm8001_ha->smp_exp_mode == SMP_INDIRECT) { @@ -4186,7 +4190,7 @@ static int pm80xx_chip_smp_req(struct pm8001_hba_info *pm8001_ha, /* for SPCv indirect mode. Place the top 4 bytes of * SMP Request header here. */ for (i = 0; i < 4; i++) - smp_cmd.smp_req16[i] = *(preq_dma_addr + i); + smp_cmd.smp_req16[i] = *(payload + i); /* exclude top 4 bytes for SMP req header */ smp_cmd.long_smp_req.long_req_addr = cpu_to_le64((u64)sg_dma_address @@ -4217,20 +4221,20 @@ static int pm80xx_chip_smp_req(struct pm8001_hba_info *pm8001_ha, pm8001_dbg(pm8001_ha, IO, "SMP REQUEST DIRECT MODE\n"); for (i = 0; i < length; i++) if (i < 16) { - smp_cmd.smp_req16[i] = *(preq_dma_addr+i); + smp_cmd.smp_req16[i] = *(payload + i); pm8001_dbg(pm8001_ha, IO, "Byte[%d]:%x (DMA data:%x)\n", i, smp_cmd.smp_req16[i], - *(preq_dma_addr)); + *(payload)); } else { - smp_cmd.smp_req[i] = *(preq_dma_addr+i); + smp_cmd.smp_req[i] = *(payload + i); pm8001_dbg(pm8001_ha, IO, "Byte[%d]:%x (DMA data:%x)\n", i, smp_cmd.smp_req[i], - *(preq_dma_addr)); + *(payload)); } } - + kunmap_atomic(to); build_smp_cmd(pm8001_dev->device_id, smp_cmd.tag, &smp_cmd, pm8001_ha->smp_exp_mode, length); rc = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &smp_cmd,
From: Ilan Peer ilan.peer@intel.com
[ Upstream commit f22d981386d12d1513bd2720fb4387b469124d4b ]
Instead of using the hard-coded value of '100' use the correct scan IEs length as calculated during HW registration to mac80211.
Signed-off-by: Ilan Peer ilan.peer@intel.com Signed-off-by: Luca Coelho luciano.coelho@intel.com Link: https://lore.kernel.org/r/iwlwifi.20211129152938.0a82d6891719.I8ded1f2e0bccb... Signed-off-by: Johannes Berg johannes.berg@intel.com Signed-off-by: Sasha Levin sashal@kernel.org --- net/mac80211/util.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/net/mac80211/util.c b/net/mac80211/util.c index fbf56a203c0e8..5dfa26b533802 100644 --- a/net/mac80211/util.c +++ b/net/mac80211/util.c @@ -2040,7 +2040,7 @@ struct sk_buff *ieee80211_build_probe_req(struct ieee80211_sub_if_data *sdata, chandef.chan = chan;
skb = ieee80211_probereq_get(&local->hw, src, ssid, ssid_len, - 100 + ie_len); + local->scan_ies_len + ie_len); if (!skb) return NULL;
From: Mordechay Goodstein mordechay.goodstein@intel.com
[ Upstream commit 4dde3c3627b52ca515a34f6f4de3898224aa1dd3 ]
Currently channel context is updated only after station got an update about new assoc state, this results in station using the old channel context.
Fix this by moving the update channel context before updating station, enabling the driver to immediately use the updated channel context in the new assoc state.
Signed-off-by: Mordechay Goodstein mordechay.goodstein@intel.com Signed-off-by: Luca Coelho luciano.coelho@intel.com Link: https://lore.kernel.org/r/iwlwifi.20211129152938.1c80c17ffd8a.I94ae31378b363... Signed-off-by: Johannes Berg johannes.berg@intel.com Signed-off-by: Sasha Levin sashal@kernel.org --- net/mac80211/sta_info.c | 15 +++++++++------ 1 file changed, 9 insertions(+), 6 deletions(-)
diff --git a/net/mac80211/sta_info.c b/net/mac80211/sta_info.c index 461c03737da8d..3ccd1a311ff9c 100644 --- a/net/mac80211/sta_info.c +++ b/net/mac80211/sta_info.c @@ -668,6 +668,15 @@ static int sta_info_insert_finish(struct sta_info *sta) __acquires(RCU)
list_add_tail_rcu(&sta->list, &local->sta_list);
+ /* update channel context before notifying the driver about state + * change, this enables driver using the updated channel context right away. + */ + if (sta->sta_state >= IEEE80211_STA_ASSOC) { + ieee80211_recalc_min_chandef(sta->sdata); + if (!sta->sta.support_p2p_ps) + ieee80211_recalc_p2p_go_ps_allowed(sta->sdata); + } + /* notify driver */ err = sta_info_insert_drv_state(local, sdata, sta); if (err) @@ -675,12 +684,6 @@ static int sta_info_insert_finish(struct sta_info *sta) __acquires(RCU)
set_sta_flag(sta, WLAN_STA_INSERTED);
- if (sta->sta_state >= IEEE80211_STA_ASSOC) { - ieee80211_recalc_min_chandef(sta->sdata); - if (!sta->sta.support_p2p_ps) - ieee80211_recalc_p2p_go_ps_allowed(sta->sdata); - } - /* accept BA sessions now */ clear_sta_flag(sta, WLAN_STA_BLOCK_BA);
From: Johannes Berg johannes.berg@intel.com
[ Upstream commit 13dee10b30c058ee2c58c5da00339cc0d4201aa6 ]
When we reconfigure, the driver might do some things to complete the reconfiguration. It's strange and could be broken in some cases because we restart other works (e.g. remain-on-channel and TX) before this happens, yet only start queues later.
Change this to do the reconfig complete when reconfiguration is actually complete, not when we've already started doing other things again.
For iwlwifi, this should fix a race where the reconfig can race with TX, for ath10k and ath11k that also use this it won't make a difference because they just start queues there, and mac80211 also stopped the queues and will restart them later as before.
Signed-off-by: Johannes Berg johannes.berg@intel.com Signed-off-by: Luca Coelho luciano.coelho@intel.com Link: https://lore.kernel.org/r/iwlwifi.20211129152938.cab99f22fe19.Iefe494687f15f... Signed-off-by: Johannes Berg johannes.berg@intel.com Signed-off-by: Sasha Levin sashal@kernel.org --- net/mac80211/util.c | 14 +++++++------- 1 file changed, 7 insertions(+), 7 deletions(-)
diff --git a/net/mac80211/util.c b/net/mac80211/util.c index 5dfa26b533802..dcebb0eb8a4be 100644 --- a/net/mac80211/util.c +++ b/net/mac80211/util.c @@ -2624,6 +2624,13 @@ int ieee80211_reconfig(struct ieee80211_local *local) mutex_unlock(&local->sta_mtx); }
+ /* + * If this is for hw restart things are still running. + * We may want to change that later, however. + */ + if (local->open_count && (!suspended || reconfig_due_to_wowlan)) + drv_reconfig_complete(local, IEEE80211_RECONFIG_TYPE_RESTART); + if (local->in_reconfig) { local->in_reconfig = false; barrier(); @@ -2642,13 +2649,6 @@ int ieee80211_reconfig(struct ieee80211_local *local) IEEE80211_QUEUE_STOP_REASON_SUSPEND, false);
- /* - * If this is for hw restart things are still running. - * We may want to change that later, however. - */ - if (local->open_count && (!suspended || reconfig_due_to_wowlan)) - drv_reconfig_complete(local, IEEE80211_RECONFIG_TYPE_RESTART); - if (!suspended) return 0;
From: Nicholas Kazlauskas nicholas.kazlauskas@amd.com
[ Upstream commit 791255ca9fbe38042cfd55df5deb116dc11fef18 ]
[Why] If the firmware wasn't reset by PSP or HW and is currently running then the firmware will hang or perform underfined behavior when we modify its firmware state underneath it.
[How] Reset DMCUB before setting up cache windows and performing HW init.
Reviewed-by: Aurabindo Jayamohanan Pillai Aurabindo.Pillai@amd.com Acked-by: Pavle Kotarac Pavle.Kotarac@amd.com Tested-by: Daniel Wheeler daniel.wheeler@amd.com Signed-off-by: Nicholas Kazlauskas nicholas.kazlauskas@amd.com Signed-off-by: Alex Deucher alexander.deucher@amd.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.c | 5 +++++ 1 file changed, 5 insertions(+)
diff --git a/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.c b/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.c index a5b6f36fe1d72..060d31db0c347 100644 --- a/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.c +++ b/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.c @@ -794,6 +794,11 @@ static int dm_dmub_hw_init(struct amdgpu_device *adev) return 0; }
+ /* Reset DMCUB if it was previously running - before we overwrite its memory. */ + status = dmub_srv_hw_reset(dmub_srv); + if (status != DMUB_STATUS_OK) + DRM_WARN("Error resetting DMUB HW: %d\n", status); + hdr = (const struct dmcub_firmware_header_v1_0 *)dmub_fw->data;
fw_inst_const = dmub_fw->data +
From: Evan Quan evan.quan@amd.com
[ Upstream commit 17c65d6fca844ee72a651944d8ce721e9040bf70 ]
Pair the operations did in GMC ->hw_init and ->hw_fini. That can help to maintain correct cached state for GMC and avoid unintention gate operation dropping due to wrong cached state.
BugLink: https://gitlab.freedesktop.org/drm/amd/-/issues/1828
Signed-off-by: Evan Quan evan.quan@amd.com Acked-by: Guchun Chen guchun.chen@amd.com Reviewed-by: Mario Limonciello mario.limonciello@amd.com Signed-off-by: Alex Deucher alexander.deucher@amd.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/gpu/drm/amd/amdgpu/gmc_v9_0.c | 8 ++++++++ drivers/gpu/drm/amd/amdgpu/mmhub_v1_0.c | 8 ++++---- drivers/gpu/drm/amd/pm/powerplay/amd_powerplay.c | 7 ++++++- 3 files changed, 18 insertions(+), 5 deletions(-)
diff --git a/drivers/gpu/drm/amd/amdgpu/gmc_v9_0.c b/drivers/gpu/drm/amd/amdgpu/gmc_v9_0.c index 3a864041968f6..68501f7a3ad5a 100644 --- a/drivers/gpu/drm/amd/amdgpu/gmc_v9_0.c +++ b/drivers/gpu/drm/amd/amdgpu/gmc_v9_0.c @@ -1685,6 +1685,14 @@ static int gmc_v9_0_hw_fini(void *handle) return 0; }
+ /* + * Pair the operations did in gmc_v9_0_hw_init and thus maintain + * a correct cached state for GMC. Otherwise, the "gate" again + * operation on S3 resuming will fail due to wrong cached state. + */ + if (adev->mmhub.funcs->update_power_gating) + adev->mmhub.funcs->update_power_gating(adev, false); + amdgpu_irq_put(adev, &adev->gmc.ecc_irq, 0); amdgpu_irq_put(adev, &adev->gmc.vm_fault, 0);
diff --git a/drivers/gpu/drm/amd/amdgpu/mmhub_v1_0.c b/drivers/gpu/drm/amd/amdgpu/mmhub_v1_0.c index f84701c562bf2..12669c95d03be 100644 --- a/drivers/gpu/drm/amd/amdgpu/mmhub_v1_0.c +++ b/drivers/gpu/drm/amd/amdgpu/mmhub_v1_0.c @@ -303,10 +303,10 @@ static void mmhub_v1_0_update_power_gating(struct amdgpu_device *adev, if (amdgpu_sriov_vf(adev)) return;
- if (enable && adev->pg_flags & AMD_PG_SUPPORT_MMHUB) { - amdgpu_dpm_set_powergating_by_smu(adev, AMD_IP_BLOCK_TYPE_GMC, true); - - } + if (adev->pg_flags & AMD_PG_SUPPORT_MMHUB) + amdgpu_dpm_set_powergating_by_smu(adev, + AMD_IP_BLOCK_TYPE_GMC, + enable); }
static int mmhub_v1_0_gart_enable(struct amdgpu_device *adev) diff --git a/drivers/gpu/drm/amd/pm/powerplay/amd_powerplay.c b/drivers/gpu/drm/amd/pm/powerplay/amd_powerplay.c index eab9768029c11..dc0dbd2fd49db 100644 --- a/drivers/gpu/drm/amd/pm/powerplay/amd_powerplay.c +++ b/drivers/gpu/drm/amd/pm/powerplay/amd_powerplay.c @@ -1317,7 +1317,12 @@ static int pp_set_powergating_by_smu(void *handle, pp_dpm_powergate_vce(handle, gate); break; case AMD_IP_BLOCK_TYPE_GMC: - pp_dpm_powergate_mmhub(handle); + /* + * For now, this is only used on PICASSO. + * And only "gate" operation is supported. + */ + if (gate) + pp_dpm_powergate_mmhub(handle); break; case AMD_IP_BLOCK_TYPE_GFX: ret = pp_dpm_powergate_gfx(handle, gate);
From: Jens Axboe axboe@kernel.dk
[ Upstream commit cb2ac2912a9ca7d3d26291c511939a41361d2d83 ]
Dexuan reports that he's seeing spikes of very heavy CPU utilization when running 24 disks and using the 'none' scheduler. This happens off the sched restart path, because SCSI requires the queue to be restarted async, and hence we're hammering on mod_delayed_work_on() to ensure that the work item gets run appropriately.
Avoid hammering on the timer and just use queue_work_on() if no delay has been specified.
Reported-and-tested-by: Dexuan Cui decui@microsoft.com Link: https://lore.kernel.org/linux-block/BYAPR21MB1270C598ED214C0490F47400BF719@B... Reviewed-by: Ming Lei ming.lei@redhat.com Signed-off-by: Jens Axboe axboe@kernel.dk Signed-off-by: Sasha Levin sashal@kernel.org --- block/blk-core.c | 2 ++ 1 file changed, 2 insertions(+)
diff --git a/block/blk-core.c b/block/blk-core.c index 26664f2a139eb..4f4e286198660 100644 --- a/block/blk-core.c +++ b/block/blk-core.c @@ -1657,6 +1657,8 @@ EXPORT_SYMBOL(kblockd_schedule_work); int kblockd_mod_delayed_work_on(int cpu, struct delayed_work *dwork, unsigned long delay) { + if (!delay) + return queue_work_on(cpu, kblockd_workqueue, &dwork->work); return mod_delayed_work_on(cpu, kblockd_workqueue, dwork, delay); } EXPORT_SYMBOL(kblockd_mod_delayed_work_on);
From: Greg Jesionowski jesionowskigreg@gmail.com
[ Upstream commit ef8a0f6eab1ca5d1a75c242c5c7b9d386735fa0a ]
This adds the vendor and product IDs for the AT29M2-AF which is a lan7801-based device.
Signed-off-by: Greg Jesionowski jesionowskigreg@gmail.com Link: https://lore.kernel.org/r/20211214221027.305784-1-jesionowskigreg@gmail.com Signed-off-by: Jakub Kicinski kuba@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/net/usb/lan78xx.c | 6 ++++++ 1 file changed, 6 insertions(+)
diff --git a/drivers/net/usb/lan78xx.c b/drivers/net/usb/lan78xx.c index c666e990900b9..6f7b70522d926 100644 --- a/drivers/net/usb/lan78xx.c +++ b/drivers/net/usb/lan78xx.c @@ -64,6 +64,8 @@ #define LAN7801_USB_PRODUCT_ID (0x7801) #define LAN78XX_EEPROM_MAGIC (0x78A5) #define LAN78XX_OTP_MAGIC (0x78F3) +#define AT29M2AF_USB_VENDOR_ID (0x07C9) +#define AT29M2AF_USB_PRODUCT_ID (0x0012)
#define MII_READ 1 #define MII_WRITE 0 @@ -4142,6 +4144,10 @@ static const struct usb_device_id products[] = { /* LAN7801 USB Gigabit Ethernet Device */ USB_DEVICE(LAN78XX_USB_VENDOR_ID, LAN7801_USB_PRODUCT_ID), }, + { + /* ATM2-AF USB Gigabit Ethernet Device */ + USB_DEVICE(AT29M2AF_USB_VENDOR_ID, AT29M2AF_USB_PRODUCT_ID), + }, {}, }; MODULE_DEVICE_TABLE(usb, products);
From: Wenliang Wang wangwenliang.1995@bytedance.com
[ Upstream commit 053c9e18c6f9cf82242ef35ac21cae1842725714 ]
We found the stat of rx drops for small pkts does not increment when build_skb fail, it's not coherent with other mode's rx drops stat.
Signed-off-by: Wenliang Wang wangwenliang.1995@bytedance.com Acked-by: Jason Wang jasowang@redhat.com Acked-by: Michael S. Tsirkin mst@redhat.com Signed-off-by: David S. Miller davem@davemloft.net Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/net/virtio_net.c | 9 +++------ 1 file changed, 3 insertions(+), 6 deletions(-)
diff --git a/drivers/net/virtio_net.c b/drivers/net/virtio_net.c index cbe47eed7cc3c..3ba289b695f04 100644 --- a/drivers/net/virtio_net.c +++ b/drivers/net/virtio_net.c @@ -697,7 +697,7 @@ static struct sk_buff *receive_small(struct net_device *dev, pr_debug("%s: rx error: len %u exceeds max size %d\n", dev->name, len, GOOD_PACKET_LEN); dev->stats.rx_length_errors++; - goto err_len; + goto err; } rcu_read_lock(); xdp_prog = rcu_dereference(rq->xdp_prog); @@ -782,10 +782,8 @@ static struct sk_buff *receive_small(struct net_device *dev, rcu_read_unlock();
skb = build_skb(buf, buflen); - if (!skb) { - put_page(page); + if (!skb) goto err; - } skb_reserve(skb, headroom - delta); skb_put(skb, len); if (!xdp_prog) { @@ -796,13 +794,12 @@ static struct sk_buff *receive_small(struct net_device *dev, if (metasize) skb_metadata_set(skb, metasize);
-err: return skb;
err_xdp: rcu_read_unlock(); stats->xdp_drops++; -err_len: +err: stats->drops++; put_page(page); xdp_xmit:
From: Daniel Borkmann daniel@iogearbox.net
[ Upstream commit e572ff80f05c33cd0cb4860f864f5c9c044280b6 ]
Make the bounds propagation in __reg_assign_32_into_64() slightly more robust and readable by aligning it similarly as we did back in the __reg_combine_64_into_32() counterpart. Meaning, only propagate or pessimize them as a smin/smax pair.
Signed-off-by: Daniel Borkmann daniel@iogearbox.net Reviewed-by: John Fastabend john.fastabend@gmail.com Acked-by: Alexei Starovoitov ast@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- kernel/bpf/verifier.c | 24 +++++++++++++++--------- 1 file changed, 15 insertions(+), 9 deletions(-)
diff --git a/kernel/bpf/verifier.c b/kernel/bpf/verifier.c index 95ab3f243acde..2d9e04fc696a6 100644 --- a/kernel/bpf/verifier.c +++ b/kernel/bpf/verifier.c @@ -1249,22 +1249,28 @@ static void __reg_bound_offset(struct bpf_reg_state *reg) reg->var_off = tnum_or(tnum_clear_subreg(var64_off), var32_off); }
+static bool __reg32_bound_s64(s32 a) +{ + return a >= 0 && a <= S32_MAX; +} + static void __reg_assign_32_into_64(struct bpf_reg_state *reg) { reg->umin_value = reg->u32_min_value; reg->umax_value = reg->u32_max_value; - /* Attempt to pull 32-bit signed bounds into 64-bit bounds - * but must be positive otherwise set to worse case bounds - * and refine later from tnum. + + /* Attempt to pull 32-bit signed bounds into 64-bit bounds but must + * be positive otherwise set to worse case bounds and refine later + * from tnum. */ - if (reg->s32_min_value >= 0 && reg->s32_max_value >= 0) - reg->smax_value = reg->s32_max_value; - else - reg->smax_value = U32_MAX; - if (reg->s32_min_value >= 0) + if (__reg32_bound_s64(reg->s32_min_value) && + __reg32_bound_s64(reg->s32_max_value)) { reg->smin_value = reg->s32_min_value; - else + reg->smax_value = reg->s32_max_value; + } else { reg->smin_value = 0; + reg->smax_value = U32_MAX; + } }
static void __reg_combine_32_into_64(struct bpf_reg_state *reg)
From: Jens Axboe axboe@kernel.dk
[ Upstream commit 87959fa16cfbcf76245c11559db1940069621274 ]
This reverts commit cb2ac2912a9ca7d3d26291c511939a41361d2d83.
Alex and the kernel test robot report that this causes a significant performance regression with BFQ. I can reproduce that result, so let's revert this one as we're close to -rc6 and we there's no point in trying to rush a fix.
Link: https://lore.kernel.org/linux-block/1639853092.524jxfaem2.none@localhost/ Link: https://lore.kernel.org/lkml/20211219141852.GH14057@xsang-OptiPlex-9020/ Reported-by: Alex Xu (Hello71) alex_y_xu@yahoo.ca Reported-by: kernel test robot oliver.sang@intel.com Signed-off-by: Jens Axboe axboe@kernel.dk Signed-off-by: Sasha Levin sashal@kernel.org --- block/blk-core.c | 2 -- 1 file changed, 2 deletions(-)
diff --git a/block/blk-core.c b/block/blk-core.c index 4f4e286198660..26664f2a139eb 100644 --- a/block/blk-core.c +++ b/block/blk-core.c @@ -1657,8 +1657,6 @@ EXPORT_SYMBOL(kblockd_schedule_work); int kblockd_mod_delayed_work_on(int cpu, struct delayed_work *dwork, unsigned long delay) { - if (!delay) - return queue_work_on(cpu, kblockd_workqueue, &dwork->work); return mod_delayed_work_on(cpu, kblockd_workqueue, dwork, delay); } EXPORT_SYMBOL(kblockd_mod_delayed_work_on);
linux-stable-mirror@lists.linaro.org
-
Sasha Levin