This is the start of the stable review cycle for the 4.9.314 release. There are 7 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.
Responses should be made by Sun, 15 May 2022 14:22:19 +0000. Anything received after that time might be too late.
The whole patch series can be found in one patch at: https://www.kernel.org/pub/linux/kernel/v4.x/stable-review/patch-4.9.314-rc1... or in the git tree and branch at: git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-4.9.y and the diffstat can be found below.
thanks,
greg k-h
------------- Pseudo-Shortlog of commits:
Greg Kroah-Hartman gregkh@linuxfoundation.org Linux 4.9.314-rc1
Muchun Song songmuchun@bytedance.com mm: userfaultfd: fix missing cache flush in mcopy_atomic_pte() and __mcopy_atomic()
Ricky WU ricky_wu@realtek.com mmc: rtsx: add 74 Clocks in power on flow
Itay Iellin ieitayie@gmail.com Bluetooth: Fix the creation of hdev->name
Andreas Larsson andreas@gaisler.com can: grcan: only use the NAPI poll budget for RX
Andreas Larsson andreas@gaisler.com can: grcan: grcan_probe(): fix broken system id check for errata workaround needs
Lee Jones lee.jones@linaro.org block: drbd: drbd_nl: Make conversion to 'enum drbd_ret_code' explicit
Nathan Chancellor natechancellor@gmail.com MIPS: Use address-of operator on section symbols
-------------
Diffstat:
Makefile | 4 ++-- arch/mips/bmips/setup.c | 2 +- arch/mips/lantiq/prom.c | 2 +- arch/mips/pic32/pic32mzda/init.c | 2 +- drivers/block/drbd/drbd_nl.c | 13 ++++++++----- drivers/mmc/host/rtsx_pci_sdmmc.c | 30 ++++++++++++++++++++---------- drivers/net/can/grcan.c | 38 ++++++++++++++++++-------------------- include/net/bluetooth/hci_core.h | 3 +++ mm/userfaultfd.c | 3 +++ net/bluetooth/hci_core.c | 6 +++--- 10 files changed, 60 insertions(+), 43 deletions(-)
From: Nathan Chancellor natechancellor@gmail.com
commit d422c6c0644bccbb1ebeefffa51f35cec3019517 upstream.
When building xway_defconfig with clang:
arch/mips/lantiq/prom.c:82:23: error: array comparison always evaluates to true [-Werror,-Wtautological-compare] else if (__dtb_start != __dtb_end) ^ 1 error generated.
These are not true arrays, they are linker defined symbols, which are just addresses. Using the address of operator silences the warning and does not change the resulting assembly with either clang/ld.lld or gcc/ld (tested with diff + objdump -Dr). Do the same thing across the entire MIPS subsystem to ensure there are no more warnings around this type of comparison.
Link: https://github.com/ClangBuiltLinux/linux/issues/1232 Signed-off-by: Nathan Chancellor natechancellor@gmail.com Acked-by: Florian Fainelli f.fainelli@gmail.com Signed-off-by: Thomas Bogendoerfer tsbogend@alpha.franken.de Cc: Sudip Mukherjee sudipm.mukherjee@gmail.com Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- arch/mips/bmips/setup.c | 2 +- arch/mips/lantiq/prom.c | 2 +- arch/mips/pic32/pic32mzda/init.c | 2 +- 3 files changed, 3 insertions(+), 3 deletions(-)
--- a/arch/mips/bmips/setup.c +++ b/arch/mips/bmips/setup.c @@ -174,7 +174,7 @@ void __init plat_mem_setup(void) dtb = phys_to_virt(fw_arg2); else if (fw_passed_dtb) /* UHI interface */ dtb = (void *)fw_passed_dtb; - else if (__dtb_start != __dtb_end) + else if (&__dtb_start != &__dtb_end) dtb = (void *)__dtb_start; else panic("no dtb found"); --- a/arch/mips/lantiq/prom.c +++ b/arch/mips/lantiq/prom.c @@ -76,7 +76,7 @@ void __init plat_mem_setup(void)
if (fw_passed_dtb) /* UHI interface */ dtb = (void *)fw_passed_dtb; - else if (__dtb_start != __dtb_end) + else if (&__dtb_start != &__dtb_end) dtb = (void *)__dtb_start; else panic("no dtb found"); --- a/arch/mips/pic32/pic32mzda/init.c +++ b/arch/mips/pic32/pic32mzda/init.c @@ -36,7 +36,7 @@ static ulong get_fdtaddr(void) if (fw_passed_dtb && !fw_arg2 && !fw_arg3) return (ulong)fw_passed_dtb;
- if (__dtb_start < __dtb_end) + if (&__dtb_start < &__dtb_end) ftaddr = (ulong)__dtb_start;
return ftaddr;
From: Lee Jones lee.jones@linaro.org
commit 1f1e87b4dc4598eac57a69868534b92d65e47e82 upstream.
Fixes the following W=1 kernel build warning(s):
from drivers/block/drbd/drbd_nl.c:24: drivers/block/drbd/drbd_nl.c: In function ‘drbd_adm_set_role’: drivers/block/drbd/drbd_nl.c:793:11: warning: implicit conversion from ‘enum drbd_state_rv’ to ‘enum drbd_ret_code’ [-Wenum-conversion] drivers/block/drbd/drbd_nl.c:795:11: warning: implicit conversion from ‘enum drbd_state_rv’ to ‘enum drbd_ret_code’ [-Wenum-conversion] drivers/block/drbd/drbd_nl.c: In function ‘drbd_adm_attach’: drivers/block/drbd/drbd_nl.c:1965:10: warning: implicit conversion from ‘enum drbd_state_rv’ to ‘enum drbd_ret_code’ [-Wenum-conversion] drivers/block/drbd/drbd_nl.c: In function ‘drbd_adm_connect’: drivers/block/drbd/drbd_nl.c:2690:10: warning: implicit conversion from ‘enum drbd_state_rv’ to ‘enum drbd_ret_code’ [-Wenum-conversion] drivers/block/drbd/drbd_nl.c: In function ‘drbd_adm_disconnect’: drivers/block/drbd/drbd_nl.c:2803:11: warning: implicit conversion from ‘enum drbd_state_rv’ to ‘enum drbd_ret_code’ [-Wenum-conversion]
Cc: Philipp Reisner philipp.reisner@linbit.com Cc: Lars Ellenberg lars.ellenberg@linbit.com Cc: Jens Axboe axboe@kernel.dk Cc: drbd-dev@lists.linbit.com Cc: linux-block@vger.kernel.org Signed-off-by: Lee Jones lee.jones@linaro.org Link: https://lore.kernel.org/r/20210312105530.2219008-8-lee.jones@linaro.org Signed-off-by: Jens Axboe axboe@kernel.dk Cc: Nathan Chancellor nathan@kernel.org Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- drivers/block/drbd/drbd_nl.c | 13 ++++++++----- 1 file changed, 8 insertions(+), 5 deletions(-)
--- a/drivers/block/drbd/drbd_nl.c +++ b/drivers/block/drbd/drbd_nl.c @@ -774,9 +774,11 @@ int drbd_adm_set_role(struct sk_buff *sk mutex_lock(&adm_ctx.resource->adm_mutex);
if (info->genlhdr->cmd == DRBD_ADM_PRIMARY) - retcode = drbd_set_role(adm_ctx.device, R_PRIMARY, parms.assume_uptodate); + retcode = (enum drbd_ret_code)drbd_set_role(adm_ctx.device, + R_PRIMARY, parms.assume_uptodate); else - retcode = drbd_set_role(adm_ctx.device, R_SECONDARY, 0); + retcode = (enum drbd_ret_code)drbd_set_role(adm_ctx.device, + R_SECONDARY, 0);
mutex_unlock(&adm_ctx.resource->adm_mutex); genl_lock(); @@ -1933,7 +1935,7 @@ int drbd_adm_attach(struct sk_buff *skb, drbd_flush_workqueue(&connection->sender_work);
rv = _drbd_request_state(device, NS(disk, D_ATTACHING), CS_VERBOSE); - retcode = rv; /* FIXME: Type mismatch. */ + retcode = (enum drbd_ret_code)rv; drbd_resume_io(device); if (rv < SS_SUCCESS) goto fail; @@ -2684,7 +2686,8 @@ int drbd_adm_connect(struct sk_buff *skb } rcu_read_unlock();
- retcode = conn_request_state(connection, NS(conn, C_UNCONNECTED), CS_VERBOSE); + retcode = (enum drbd_ret_code)conn_request_state(connection, + NS(conn, C_UNCONNECTED), CS_VERBOSE);
conn_reconfig_done(connection); mutex_unlock(&adm_ctx.resource->adm_mutex); @@ -2790,7 +2793,7 @@ int drbd_adm_disconnect(struct sk_buff * mutex_lock(&adm_ctx.resource->adm_mutex); rv = conn_try_disconnect(connection, parms.force_disconnect); if (rv < SS_SUCCESS) - retcode = rv; /* FIXME: Type mismatch. */ + retcode = (enum drbd_ret_code)rv; else retcode = NO_ERROR; mutex_unlock(&adm_ctx.resource->adm_mutex);
From: Andreas Larsson andreas@gaisler.com
commit 1e93ed26acf03fe6c97c6d573a10178596aadd43 upstream.
The systemid property was checked for in the wrong place of the device tree and compared to the wrong value.
Fixes: 6cec9b07fe6a ("can: grcan: Add device driver for GRCAN and GRHCAN cores") Link: https://lore.kernel.org/all/20220429084656.29788-3-andreas@gaisler.com Cc: stable@vger.kernel.org Signed-off-by: Andreas Larsson andreas@gaisler.com Signed-off-by: Marc Kleine-Budde mkl@pengutronix.de Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- drivers/net/can/grcan.c | 16 +++++++++++----- 1 file changed, 11 insertions(+), 5 deletions(-)
--- a/drivers/net/can/grcan.c +++ b/drivers/net/can/grcan.c @@ -245,7 +245,7 @@ struct grcan_device_config { .rxsize = GRCAN_DEFAULT_BUFFER_SIZE, \ }
-#define GRCAN_TXBUG_SAFE_GRLIB_VERSION 0x4100 +#define GRCAN_TXBUG_SAFE_GRLIB_VERSION 4100 #define GRLIB_VERSION_MASK 0xffff
/* GRCAN private data structure */ @@ -1665,6 +1665,7 @@ exit_free_candev: static int grcan_probe(struct platform_device *ofdev) { struct device_node *np = ofdev->dev.of_node; + struct device_node *sysid_parent; struct resource *res; u32 sysid, ambafreq; int irq, err; @@ -1674,10 +1675,15 @@ static int grcan_probe(struct platform_d /* Compare GRLIB version number with the first that does not * have the tx bug (see start_xmit) */ - err = of_property_read_u32(np, "systemid", &sysid); - if (!err && ((sysid & GRLIB_VERSION_MASK) - >= GRCAN_TXBUG_SAFE_GRLIB_VERSION)) - txbug = false; + sysid_parent = of_find_node_by_path("/ambapp0"); + if (sysid_parent) { + of_node_get(sysid_parent); + err = of_property_read_u32(sysid_parent, "systemid", &sysid); + if (!err && ((sysid & GRLIB_VERSION_MASK) >= + GRCAN_TXBUG_SAFE_GRLIB_VERSION)) + txbug = false; + of_node_put(sysid_parent); + }
err = of_property_read_u32(np, "freq", &ambafreq); if (err) {
From: Andreas Larsson andreas@gaisler.com
commit 2873d4d52f7c52d60b316ba6c47bd7122b5a9861 upstream.
The previous split budget between TX and RX made it return not using the entire budget but at the same time not having calling called napi_complete. This sometimes led to the poll to not be called, and at the same time having TX and RX interrupts disabled resulting in the driver getting stuck.
Fixes: 6cec9b07fe6a ("can: grcan: Add device driver for GRCAN and GRHCAN cores") Link: https://lore.kernel.org/all/20220429084656.29788-4-andreas@gaisler.com Cc: stable@vger.kernel.org Signed-off-by: Andreas Larsson andreas@gaisler.com Signed-off-by: Marc Kleine-Budde mkl@pengutronix.de Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- drivers/net/can/grcan.c | 22 +++++++--------------- 1 file changed, 7 insertions(+), 15 deletions(-)
--- a/drivers/net/can/grcan.c +++ b/drivers/net/can/grcan.c @@ -1141,7 +1141,7 @@ static int grcan_close(struct net_device return 0; }
-static int grcan_transmit_catch_up(struct net_device *dev, int budget) +static void grcan_transmit_catch_up(struct net_device *dev) { struct grcan_priv *priv = netdev_priv(dev); unsigned long flags; @@ -1149,7 +1149,7 @@ static int grcan_transmit_catch_up(struc
spin_lock_irqsave(&priv->lock, flags);
- work_done = catch_up_echo_skb(dev, budget, true); + work_done = catch_up_echo_skb(dev, -1, true); if (work_done) { if (!priv->resetting && !priv->closing && !(priv->can.ctrlmode & CAN_CTRLMODE_LISTENONLY)) @@ -1163,8 +1163,6 @@ static int grcan_transmit_catch_up(struc }
spin_unlock_irqrestore(&priv->lock, flags); - - return work_done; }
static int grcan_receive(struct net_device *dev, int budget) @@ -1246,19 +1244,13 @@ static int grcan_poll(struct napi_struct struct net_device *dev = priv->dev; struct grcan_registers __iomem *regs = priv->regs; unsigned long flags; - int tx_work_done, rx_work_done; - int rx_budget = budget / 2; - int tx_budget = budget - rx_budget; + int work_done;
- /* Half of the budget for receiveing messages */ - rx_work_done = grcan_receive(dev, rx_budget); + work_done = grcan_receive(dev, budget);
- /* Half of the budget for transmitting messages as that can trigger echo - * frames being received - */ - tx_work_done = grcan_transmit_catch_up(dev, tx_budget); + grcan_transmit_catch_up(dev);
- if (rx_work_done < rx_budget && tx_work_done < tx_budget) { + if (work_done < budget) { napi_complete(napi);
/* Guarantee no interference with a running reset that otherwise @@ -1275,7 +1267,7 @@ static int grcan_poll(struct napi_struct spin_unlock_irqrestore(&priv->lock, flags); }
- return rx_work_done + tx_work_done; + return work_done; }
/* Work tx bug by waiting while for the risky situation to clear. If that fails,
From: Itay Iellin ieitayie@gmail.com
commit 103a2f3255a95991252f8f13375c3a96a75011cd upstream.
Set a size limit of 8 bytes of the written buffer to "hdev->name" including the terminating null byte, as the size of "hdev->name" is 8 bytes. If an id value which is greater than 9999 is allocated, then the "snprintf(hdev->name, sizeof(hdev->name), "hci%d", id)" function call would lead to a truncation of the id value in decimal notation.
Set an explicit maximum id parameter in the id allocation function call. The id allocation function defines the maximum allocated id value as the maximum id parameter value minus one. Therefore, HCI_MAX_ID is defined as 10000.
Signed-off-by: Itay Iellin ieitayie@gmail.com Signed-off-by: Luiz Augusto von Dentz luiz.von.dentz@intel.com Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- include/net/bluetooth/hci_core.h | 3 +++ net/bluetooth/hci_core.c | 6 +++--- 2 files changed, 6 insertions(+), 3 deletions(-)
--- a/include/net/bluetooth/hci_core.h +++ b/include/net/bluetooth/hci_core.h @@ -32,6 +32,9 @@ /* HCI priority */ #define HCI_PRIO_MAX 7
+/* HCI maximum id value */ +#define HCI_MAX_ID 10000 + /* HCI Core structures */ struct inquiry_data { bdaddr_t bdaddr; --- a/net/bluetooth/hci_core.c +++ b/net/bluetooth/hci_core.c @@ -3064,10 +3064,10 @@ int hci_register_dev(struct hci_dev *hde */ switch (hdev->dev_type) { case HCI_PRIMARY: - id = ida_simple_get(&hci_index_ida, 0, 0, GFP_KERNEL); + id = ida_simple_get(&hci_index_ida, 0, HCI_MAX_ID, GFP_KERNEL); break; case HCI_AMP: - id = ida_simple_get(&hci_index_ida, 1, 0, GFP_KERNEL); + id = ida_simple_get(&hci_index_ida, 1, HCI_MAX_ID, GFP_KERNEL); break; default: return -EINVAL; @@ -3076,7 +3076,7 @@ int hci_register_dev(struct hci_dev *hde if (id < 0) return id;
- sprintf(hdev->name, "hci%d", id); + snprintf(hdev->name, sizeof(hdev->name), "hci%d", id); hdev->id = id;
BT_DBG("%p name %s bus %d", hdev, hdev->name, hdev->bus);
From: Ricky WU ricky_wu@realtek.com
commit 1f311c94aabdb419c28e3147bcc8ab89269f1a7e upstream.
SD spec definition: "Host provides at least 74 Clocks before issuing first command" After 1ms for the voltage stable then start issuing the Clock signals
if POWER STATE is MMC_POWER_OFF to MMC_POWER_UP to issue Clock signal to card MMC_POWER_UP to MMC_POWER_ON to stop issuing signal to card
Signed-off-by: Ricky Wu ricky_wu@realtek.com Link: https://lore.kernel.org/r/1badf10aba764191a1a752edcbf90389@realtek.com Signed-off-by: Ulf Hansson ulf.hansson@linaro.org Signed-off-by: Ricky Wu ricky_wu@realtek.com Signed-off-by: Ulf Hansson ulf.hansson@linaro.org Signed-off-by: Christian Loehle cloehle@hyperstone.com Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- drivers/mmc/host/rtsx_pci_sdmmc.c | 30 ++++++++++++++++++++---------- 1 file changed, 20 insertions(+), 10 deletions(-)
--- a/drivers/mmc/host/rtsx_pci_sdmmc.c +++ b/drivers/mmc/host/rtsx_pci_sdmmc.c @@ -49,10 +49,7 @@ struct realtek_pci_sdmmc { bool double_clk; bool eject; bool initial_mode; - int power_state; -#define SDMMC_POWER_ON 1 -#define SDMMC_POWER_OFF 0 - + int prev_power_state; int sg_count; s32 cookie; int cookie_sg_count; @@ -914,14 +911,21 @@ static int sd_set_bus_width(struct realt return err; }
-static int sd_power_on(struct realtek_pci_sdmmc *host) +static int sd_power_on(struct realtek_pci_sdmmc *host, unsigned char power_mode) { struct rtsx_pcr *pcr = host->pcr; int err;
- if (host->power_state == SDMMC_POWER_ON) + if (host->prev_power_state == MMC_POWER_ON) return 0;
+ if (host->prev_power_state == MMC_POWER_UP) { + rtsx_pci_write_register(pcr, SD_BUS_STAT, SD_CLK_TOGGLE_EN, 0); + goto finish; + } + + msleep(100); + rtsx_pci_init_cmd(pcr); rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, CARD_SELECT, 0x07, SD_MOD_SEL); rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, CARD_SHARE_MODE, @@ -940,11 +944,17 @@ static int sd_power_on(struct realtek_pc if (err < 0) return err;
+ mdelay(1); + err = rtsx_pci_write_register(pcr, CARD_OE, SD_OUTPUT_EN, SD_OUTPUT_EN); if (err < 0) return err;
- host->power_state = SDMMC_POWER_ON; + /* send at least 74 clocks */ + rtsx_pci_write_register(pcr, SD_BUS_STAT, SD_CLK_TOGGLE_EN, SD_CLK_TOGGLE_EN); + +finish: + host->prev_power_state = power_mode; return 0; }
@@ -953,7 +963,7 @@ static int sd_power_off(struct realtek_p struct rtsx_pcr *pcr = host->pcr; int err;
- host->power_state = SDMMC_POWER_OFF; + host->prev_power_state = MMC_POWER_OFF;
rtsx_pci_init_cmd(pcr);
@@ -979,7 +989,7 @@ static int sd_set_power_mode(struct real if (power_mode == MMC_POWER_OFF) err = sd_power_off(host); else - err = sd_power_on(host); + err = sd_power_on(host, power_mode);
return err; } @@ -1417,7 +1427,7 @@ static int rtsx_pci_sdmmc_drv_probe(stru host->mmc = mmc; host->pdev = pdev; host->cookie = -1; - host->power_state = SDMMC_POWER_OFF; + host->prev_power_state = MMC_POWER_OFF; INIT_WORK(&host->work, sd_request); platform_set_drvdata(pdev, host); pcr->slots[RTSX_SD_CARD].p_dev = pdev;
From: Muchun Song songmuchun@bytedance.com
commit 7c25a0b89a487878b0691e6524fb5a8827322194 upstream.
userfaultfd calls mcopy_atomic_pte() and __mcopy_atomic() which do not do any cache flushing for the target page. Then the target page will be mapped to the user space with a different address (user address), which might have an alias issue with the kernel address used to copy the data from the user to. Fix this by insert flush_dcache_page() after copy_from_user() succeeds.
Link: https://lkml.kernel.org/r/20220210123058.79206-7-songmuchun@bytedance.com Fixes: b6ebaedb4cb1 ("userfaultfd: avoid mmap_sem read recursion in mcopy_atomic") Fixes: c1a4de99fada ("userfaultfd: mcopy_atomic|mfill_zeropage: UFFDIO_COPY|UFFDIO_ZEROPAGE preparation") Signed-off-by: Muchun Song songmuchun@bytedance.com Cc: Axel Rasmussen axelrasmussen@google.com Cc: David Rientjes rientjes@google.com Cc: Fam Zheng fam.zheng@bytedance.com Cc: Kirill A. Shutemov kirill.shutemov@linux.intel.com Cc: Lars Persson lars.persson@axis.com Cc: Mike Kravetz mike.kravetz@oracle.com Cc: Peter Xu peterx@redhat.com Cc: Xiongchun Duan duanxiongchun@bytedance.com Cc: Zi Yan ziy@nvidia.com Signed-off-by: Andrew Morton akpm@linux-foundation.org Signed-off-by: Linus Torvalds torvalds@linux-foundation.org Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- mm/userfaultfd.c | 3 +++ 1 file changed, 3 insertions(+)
--- a/mm/userfaultfd.c +++ b/mm/userfaultfd.c @@ -50,6 +50,8 @@ static int mcopy_atomic_pte(struct mm_st /* don't free the page */ goto out; } + + flush_dcache_page(page); } else { page = *pagep; *pagep = NULL; @@ -267,6 +269,7 @@ retry: err = -EFAULT; goto out; } + flush_dcache_page(page); goto retry; } else BUG_ON(page);
On Fri, 13 May 2022 16:23:15 +0200, Greg Kroah-Hartman wrote:
This is the start of the stable review cycle for the 4.9.314 release. There are 7 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.
Responses should be made by Sun, 15 May 2022 14:22:19 +0000. Anything received after that time might be too late.
The whole patch series can be found in one patch at: https://www.kernel.org/pub/linux/kernel/v4.x/stable-review/patch-4.9.314-rc1... or in the git tree and branch at: git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-4.9.y and the diffstat can be found below.
thanks,
greg k-h
All tests passing for Tegra ...
Test results for stable-v4.9: 8 builds: 8 pass, 0 fail 16 boots: 16 pass, 0 fail 32 tests: 32 pass, 0 fail
Linux version: 4.9.314-rc1-g0d0d580b3778 Boards tested: tegra124-jetson-tk1, tegra20-ventana, tegra210-p2371-2180, tegra30-cardhu-a04
Tested-by: Jon Hunter jonathanh@nvidia.com
Jon
Hi!
This is the start of the stable review cycle for the 4.9.314 release. There are 7 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.
CIP testing did not find any problems here:
https://gitlab.com/cip-project/cip-testing/linux-stable-rc-ci/-/tree/linux-4...
Tested-by: Pavel Machek (CIP) pavel@denx.de
Best regards, Pavel
On 5/13/22 8:23 AM, Greg Kroah-Hartman wrote:
This is the start of the stable review cycle for the 4.9.314 release. There are 7 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.
Responses should be made by Sun, 15 May 2022 14:22:19 +0000. Anything received after that time might be too late.
The whole patch series can be found in one patch at: https://www.kernel.org/pub/linux/kernel/v4.x/stable-review/patch-4.9.314-rc1... or in the git tree and branch at: git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-4.9.y and the diffstat can be found below.
thanks,
greg k-h
Compiled and booted on my test system. No dmesg regressions.
Tested-by: Shuah Khan skhan@linuxfoundation.org
thanks, -- Shuah
On 5/13/22 07:23, Greg Kroah-Hartman wrote:
This is the start of the stable review cycle for the 4.9.314 release. There are 7 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.
Responses should be made by Sun, 15 May 2022 14:22:19 +0000. Anything received after that time might be too late.
The whole patch series can be found in one patch at: https://www.kernel.org/pub/linux/kernel/v4.x/stable-review/patch-4.9.314-rc1... or in the git tree and branch at: git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-4.9.y and the diffstat can be found below.
thanks,
greg k-h
On ARCH_BRCMSTB using 32-bit and 64-bit ARM kernels:
Tested-by: Florian Fainelli f.fainelli@gmail.com
On Fri, May 13, 2022 at 04:23:15PM +0200, Greg Kroah-Hartman wrote:
This is the start of the stable review cycle for the 4.9.314 release. There are 7 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.
Responses should be made by Sun, 15 May 2022 14:22:19 +0000. Anything received after that time might be too late.
Build results: total: 163 pass: 163 fail: 0 Qemu test results: total: 397 pass: 397 fail: 0
Tested-by: Guenter Roeck linux@roeck-us.net
Guenter
On Fri, 13 May 2022 at 19:54, Greg Kroah-Hartman gregkh@linuxfoundation.org wrote:
This is the start of the stable review cycle for the 4.9.314 release. There are 7 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.
Responses should be made by Sun, 15 May 2022 14:22:19 +0000. Anything received after that time might be too late.
The whole patch series can be found in one patch at: https://www.kernel.org/pub/linux/kernel/v4.x/stable-review/patch-4.9.314-rc1... or in the git tree and branch at: git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-4.9.y and the diffstat can be found below.
thanks,
greg k-h
Results from Linaro’s test farm. No regressions on arm64, arm, x86_64, and i386.
Tested-by: Linux Kernel Functional Testing lkft@linaro.org
## Build * kernel: 4.9.314-rc1 * git: https://gitlab.com/Linaro/lkft/mirrors/stable/linux-stable-rc * git branch: linux-4.9.y * git commit: 0d0d580b3778c2a438b6315b8f80b87835d1f3e1 * git describe: v4.9.313-8-g0d0d580b3778 * test details: https://qa-reports.linaro.org/lkft/linux-stable-rc-linux-4.9.y/build/v4.9.31...
## Test Regressions (compared to v4.9.312-67-gbc7a724ac0ce) No test regressions found.
## Metric Regressions (compared to v4.9.312-67-gbc7a724ac0ce) No metric regressions found.
## Test Fixes (compared to v4.9.312-67-gbc7a724ac0ce) No test fixes found.
## Metric Fixes (compared to v4.9.312-67-gbc7a724ac0ce) No metric fixes found.
## Test result summary total: 64906, pass: 51271, fail: 739, skip: 11179, xfail: 1717
## Build Summary * arm: 238 total, 238 passed, 0 failed * arm64: 32 total, 32 passed, 0 failed * dragonboard-410c: 1 total, 1 passed, 0 failed * hi6220-hikey: 1 total, 1 passed, 0 failed * i386: 19 total, 19 passed, 0 failed * juno-r2: 1 total, 1 passed, 0 failed * mips: 22 total, 22 passed, 0 failed * sparc: 12 total, 12 passed, 0 failed * x15: 1 total, 1 passed, 0 failed * x86: 1 total, 1 passed, 0 failed * x86_64: 31 total, 31 passed, 0 failed
## Test suites summary * fwts * kselftest-android * kselftest-arm64 * kselftest-bpf * kselftest-breakpoints * kselftest-capabilities * kselftest-cgroup * kselftest-clone3 * kselftest-core * kselftest-cpu-hotplug * kselftest-cpufreq * kselftest-drivers * kselftest-efivarfs * kselftest-filesystems * kselftest-firmware * kselftest-fpu * kselftest-futex * kselftest-gpio * kselftest-intel_pstate * kselftest-ipc * kselftest-ir * kselftest-kcmp * kselftest-kexec * kselftest-kvm * kselftest-lib * kselftest-livepatch * kselftest-membarrier * kselftest-openat2 * kselftest-pid_namespace * kselftest-pidfd * kselftest-proc * kselftest-pstore * kselftest-ptrace * kselftest-rseq * kselftest-rtc * kselftest-seccomp * kselftest-sigaltstack * kselftest-size * kselftest-splice * kselftest-static_keys * kselftest-sync * kselftest-sysctl * kselftest-timens * kselftest-timers * kselftest-tmpfs * kselftest-tpm2 * kselftest-user * kselftest-vm * kselftest-x86 * kselftest-zram * kselftest-zram[ * kvm-unit-tests * libhugetlbfs * linux-log-parser * ltp-cap_bounds-tests * ltp-commands-tests * ltp-containers-tests * ltp-controllers-tests * ltp-cpuhotplug-tests * ltp-crypto-tests * ltp-cve-tests * ltp-dio-tests * ltp-fcntl-locktests-tests * ltp-filecaps-tests * ltp-fs-tests * ltp-fs_bind-tests * ltp-fs_perms_simple-tests * ltp-fsx-tests * ltp-hugetlb-tests * ltp-io-tests * ltp-ipc-tests * ltp-math-tests * ltp-mm-tests * ltp-nptl-tests * ltp-open-posix-tests * ltp-pty-tests * ltp-sched-tests * ltp-securebits-tests * ltp-syscalls-tests * ltp-tracing-tests * network-basic-tests * packetdrill * perf * ssuite * v4l2-compliance * vdso
-- Linaro LKFT https://lkft.linaro.org
linux-stable-mirror@lists.linaro.org
-
Florian Fainelli -
Greg Kroah-Hartman -
Guenter Roeck -
Jon Hunter -
Naresh Kamboju -
Pavel Machek -
Shuah Khan