We need to apply 2685c77b80a8 ("thermal/drivers/int340x: Fix RFIM mailbox write commands") to the 5.15-stable tree but it does not apply. This patch fix the write operation for mailbox command for RFIM (cmd = 0x08) which is ignored. This results in failing to store RFI restriction.
To apply this fix, we need to backport below set of three patches on 5.15-stable tree because this fix depended on these three patches. Without these three dependent patches, we cannot directly apply fix (fourth) patch.
Backport three patches: [1] c4fcf1ada4ae ("thermal/drivers/int340x: Improve the tcc offset saving for suspend/resume") [2] 994a04a20b03 ("thermal: int340x: Limit Kconfig to 64-bit") [3] aeb58c860dc5 ("thermal/drivers/int340x: processor_thermal: Suppot 64 bit RFIM responses")
Fix RFIM patch: [4] 2685c77b80a8 ("thermal/drivers/int340x: Fix RFIM mailbox write commands")
*** BLURB HERE ***
Antoine Tenart (1): thermal/drivers/int340x: Improve the tcc offset saving for suspend/resume
Arnd Bergmann (1): thermal: int340x: Limit Kconfig to 64-bit
Srinivas Pandruvada (1): thermal/drivers/int340x: processor_thermal: Suppot 64 bit RFIM responses
Sumeet Pawnikar (1): thermal/drivers/int340x: Fix RFIM mailbox write commands
drivers/thermal/intel/int340x_thermal/Kconfig | 4 +- .../intel/int340x_thermal/int3401_thermal.c | 8 +- .../processor_thermal_device.c | 36 ++++-- .../processor_thermal_device.h | 4 +- .../processor_thermal_device_pci.c | 18 ++- .../processor_thermal_device_pci_legacy.c | 8 +- .../int340x_thermal/processor_thermal_mbox.c | 104 +++++++++++------- .../int340x_thermal/processor_thermal_rfim.c | 23 ++-- 8 files changed, 139 insertions(+), 66 deletions(-)
From: Antoine Tenart atenart@kernel.org
When the driver resumes, the tcc offset is set back to its previous value. But this only works if the value was user defined as otherwise the offset isn't saved. This asymmetric logic is harder to maintain and introduced some issues.
Improve the logic by saving the tcc offset in a suspend op, so the right value is always restored after a resume.
Signed-off-by: Antoine Tenart atenart@kernel.org Reviewed-by: Srinivas Pandruvada srinivas.pandruvada@linux.intel.com Tested-by: Srinivas Pandruvada <srinivas.pI andruvada@linux.intel.com> Link: https://lore.kernel.org/r/20210909085613.5577-3-atenart@kernel.org Signed-off-by: Daniel Lezcano daniel.lezcano@linaro.org Signed-off-by: Sumeet Pawnikar sumeet.r.pawnikar@intel.com --- .../intel/int340x_thermal/int3401_thermal.c | 8 ++++- .../processor_thermal_device.c | 36 ++++++++++++++----- .../processor_thermal_device.h | 1 + .../processor_thermal_device_pci.c | 18 +++++++++- .../processor_thermal_device_pci_legacy.c | 8 ++++- 5 files changed, 60 insertions(+), 11 deletions(-)
diff --git a/drivers/thermal/intel/int340x_thermal/int3401_thermal.c b/drivers/thermal/intel/int340x_thermal/int3401_thermal.c index acebc8ba94e2..217786fba185 100644 --- a/drivers/thermal/intel/int340x_thermal/int3401_thermal.c +++ b/drivers/thermal/intel/int340x_thermal/int3401_thermal.c @@ -44,15 +44,21 @@ static int int3401_remove(struct platform_device *pdev) }
#ifdef CONFIG_PM_SLEEP +static int int3401_thermal_suspend(struct device *dev) +{ + return proc_thermal_suspend(dev); +} static int int3401_thermal_resume(struct device *dev) { return proc_thermal_resume(dev); } #else +#define int3401_thermal_suspend NULL #define int3401_thermal_resume NULL #endif
-static SIMPLE_DEV_PM_OPS(int3401_proc_thermal_pm, NULL, int3401_thermal_resume); +static SIMPLE_DEV_PM_OPS(int3401_proc_thermal_pm, int3401_thermal_suspend, + int3401_thermal_resume);
static struct platform_driver int3401_driver = { .probe = int3401_add, diff --git a/drivers/thermal/intel/int340x_thermal/processor_thermal_device.c b/drivers/thermal/intel/int340x_thermal/processor_thermal_device.c index fb64acfd5e07..a8d98f1bd6c6 100644 --- a/drivers/thermal/intel/int340x_thermal/processor_thermal_device.c +++ b/drivers/thermal/intel/int340x_thermal/processor_thermal_device.c @@ -68,8 +68,7 @@ static const struct attribute_group power_limit_attribute_group = { .name = "power_limits" };
-static ssize_t tcc_offset_degree_celsius_show(struct device *dev, - struct device_attribute *attr, char *buf) +static int tcc_get_offset(void) { u64 val; int err; @@ -78,8 +77,20 @@ static ssize_t tcc_offset_degree_celsius_show(struct device *dev, if (err) return err;
- val = (val >> 24) & 0x3f; - return sprintf(buf, "%d\n", (int)val); + return (val >> 24) & 0x3f; +} + +static ssize_t tcc_offset_degree_celsius_show(struct device *dev, + struct device_attribute *attr, + char *buf) +{ + int tcc; + + tcc = tcc_get_offset(); + if (tcc < 0) + return tcc; + + return sprintf(buf, "%d\n", tcc); }
static int tcc_offset_update(unsigned int tcc) @@ -107,8 +118,6 @@ static int tcc_offset_update(unsigned int tcc) return 0; }
-static int tcc_offset_save = -1; - static ssize_t tcc_offset_degree_celsius_store(struct device *dev, struct device_attribute *attr, const char *buf, size_t count) @@ -131,8 +140,6 @@ static ssize_t tcc_offset_degree_celsius_store(struct device *dev, if (err) return err;
- tcc_offset_save = tcc; - return count; }
@@ -345,6 +352,18 @@ void proc_thermal_remove(struct proc_thermal_device *proc_priv) } EXPORT_SYMBOL_GPL(proc_thermal_remove);
+static int tcc_offset_save = -1; + +int proc_thermal_suspend(struct device *dev) +{ + tcc_offset_save = tcc_get_offset(); + if (tcc_offset_save < 0) + dev_warn(dev, "failed to save offset (%d)\n", tcc_offset_save); + + return 0; +} +EXPORT_SYMBOL_GPL(proc_thermal_suspend); + int proc_thermal_resume(struct device *dev) { struct proc_thermal_device *proc_dev; @@ -352,6 +371,7 @@ int proc_thermal_resume(struct device *dev) proc_dev = dev_get_drvdata(dev); proc_thermal_read_ppcc(proc_dev);
+ /* Do not update if saving failed */ if (tcc_offset_save >= 0) tcc_offset_update(tcc_offset_save);
diff --git a/drivers/thermal/intel/int340x_thermal/processor_thermal_device.h b/drivers/thermal/intel/int340x_thermal/processor_thermal_device.h index 5a1cfe4864f1..c1d8de6dc3d1 100644 --- a/drivers/thermal/intel/int340x_thermal/processor_thermal_device.h +++ b/drivers/thermal/intel/int340x_thermal/processor_thermal_device.h @@ -83,6 +83,7 @@ void proc_thermal_mbox_remove(struct pci_dev *pdev); int processor_thermal_send_mbox_cmd(struct pci_dev *pdev, u16 cmd_id, u32 cmd_data, u32 *cmd_resp); int proc_thermal_add(struct device *dev, struct proc_thermal_device *priv); void proc_thermal_remove(struct proc_thermal_device *proc_priv); +int proc_thermal_suspend(struct device *dev); int proc_thermal_resume(struct device *dev); int proc_thermal_mmio_add(struct pci_dev *pdev, struct proc_thermal_device *proc_priv, diff --git a/drivers/thermal/intel/int340x_thermal/processor_thermal_device_pci.c b/drivers/thermal/intel/int340x_thermal/processor_thermal_device_pci.c index 11dd2e825f4f..b4bcd3fe9eb2 100644 --- a/drivers/thermal/intel/int340x_thermal/processor_thermal_device_pci.c +++ b/drivers/thermal/intel/int340x_thermal/processor_thermal_device_pci.c @@ -314,6 +314,20 @@ static void proc_thermal_pci_remove(struct pci_dev *pdev) }
#ifdef CONFIG_PM_SLEEP +static int proc_thermal_pci_suspend(struct device *dev) +{ + struct pci_dev *pdev = to_pci_dev(dev); + struct proc_thermal_device *proc_priv; + struct proc_thermal_pci *pci_info; + + proc_priv = pci_get_drvdata(pdev); + pci_info = proc_priv->priv_data; + + if (!pci_info->no_legacy) + return proc_thermal_suspend(dev); + + return 0; +} static int proc_thermal_pci_resume(struct device *dev) { struct pci_dev *pdev = to_pci_dev(dev); @@ -335,10 +349,12 @@ static int proc_thermal_pci_resume(struct device *dev) return 0; } #else +#define proc_thermal_pci_suspend NULL #define proc_thermal_pci_resume NULL #endif
-static SIMPLE_DEV_PM_OPS(proc_thermal_pci_pm, NULL, proc_thermal_pci_resume); +static SIMPLE_DEV_PM_OPS(proc_thermal_pci_pm, proc_thermal_pci_suspend, + proc_thermal_pci_resume);
static const struct pci_device_id proc_thermal_pci_ids[] = { { PCI_DEVICE_DATA(INTEL, ADL_THERMAL, PROC_THERMAL_FEATURE_RAPL | PROC_THERMAL_FEATURE_FIVR | PROC_THERMAL_FEATURE_DVFS | PROC_THERMAL_FEATURE_MBOX) }, diff --git a/drivers/thermal/intel/int340x_thermal/processor_thermal_device_pci_legacy.c b/drivers/thermal/intel/int340x_thermal/processor_thermal_device_pci_legacy.c index f5fc1791b11e..4571a1a53b84 100644 --- a/drivers/thermal/intel/int340x_thermal/processor_thermal_device_pci_legacy.c +++ b/drivers/thermal/intel/int340x_thermal/processor_thermal_device_pci_legacy.c @@ -107,15 +107,21 @@ static void proc_thermal_pci_remove(struct pci_dev *pdev) }
#ifdef CONFIG_PM_SLEEP +static int proc_thermal_pci_suspend(struct device *dev) +{ + return proc_thermal_suspend(dev); +} static int proc_thermal_pci_resume(struct device *dev) { return proc_thermal_resume(dev); } #else +#define proc_thermal_pci_suspend NULL #define proc_thermal_pci_resume NULL #endif
-static SIMPLE_DEV_PM_OPS(proc_thermal_pci_pm, NULL, proc_thermal_pci_resume); +static SIMPLE_DEV_PM_OPS(proc_thermal_pci_pm, proc_thermal_pci_suspend, + proc_thermal_pci_resume);
static const struct pci_device_id proc_thermal_pci_ids[] = { { PCI_DEVICE_DATA(INTEL, BDW_THERMAL, 0) },
On Fri, Feb 11, 2022 at 03:04:34PM +0530, Sumeet Pawnikar wrote:
From: Antoine Tenart atenart@kernel.org
When the driver resumes, the tcc offset is set back to its previous value. But this only works if the value was user defined as otherwise the offset isn't saved. This asymmetric logic is harder to maintain and introduced some issues.
Improve the logic by saving the tcc offset in a suspend op, so the right value is always restored after a resume.
Signed-off-by: Antoine Tenart atenart@kernel.org Reviewed-by: Srinivas Pandruvada srinivas.pandruvada@linux.intel.com Tested-by: Srinivas Pandruvada <srinivas.pI andruvada@linux.intel.com> Link: https://lore.kernel.org/r/20210909085613.5577-3-atenart@kernel.org Signed-off-by: Daniel Lezcano daniel.lezcano@linaro.org Signed-off-by: Sumeet Pawnikar sumeet.r.pawnikar@intel.com
What is the git commit id of this commit in Linus's tree?
Same for the other 3, I need a hint here please...
thanks,
greg k-h
-----Original Message----- From: Greg KH gregkh@linuxfoundation.org Sent: Friday, February 11, 2022 2:52 PM To: Pawnikar, Sumeet R sumeet.r.pawnikar@intel.com Cc: stable@vger.kernel.org; Wysocki, Rafael J rafael.j.wysocki@intel.com; srinivas.pandruvada@linux.intel.com; Antoine Tenart atenart@kernel.org Subject: Re: [PATCH 1/4] thermal/drivers/int340x: Improve the tcc offset saving for suspend/resume
On Fri, Feb 11, 2022 at 03:04:34PM +0530, Sumeet Pawnikar wrote:
From: Antoine Tenart atenart@kernel.org
When the driver resumes, the tcc offset is set back to its previous value. But this only works if the value was user defined as otherwise the offset isn't saved. This asymmetric logic is harder to maintain and introduced some issues.
Improve the logic by saving the tcc offset in a suspend op, so the right value is always restored after a resume.
Signed-off-by: Antoine Tenart atenart@kernel.org Reviewed-by: Srinivas Pandruvada srinivas.pandruvada@linux.intel.com Tested-by: Srinivas Pandruvada <srinivas.pI andruvada@linux.intel.com> Link: https://lore.kernel.org/r/20210909085613.5577-3-atenart@kernel.org Signed-off-by: Daniel Lezcano daniel.lezcano@linaro.org Signed-off-by: Sumeet Pawnikar sumeet.r.pawnikar@intel.com
What is the git commit id of this commit in Linus's tree?
Same for the other 3, I need a hint here please...
Yes, let me add git commit id information here from Linus's tree for all four patches and submit those as V2.
Thanks, Sumeet.
thanks,
greg k-h
From: Srinivas Pandruvada srinivas.pandruvada@linux.intel.com
Some of the RFIM mail box command returns 64 bit values. So enhance mailbox interface to return 64 bit values and use them for RFIM commands.
Signed-off-by: Srinivas Pandruvada srinivas.pandruvada@linux.intel.com Fixes: 5d6fbc96bd36 ("thermal/drivers/int340x: processor_thermal: Export additional attributes") Signed-off-by: Rafael J. Wysocki rafael.j.wysocki@intel.com Signed-off-by: Sumeet Pawnikar sumeet.r.pawnikar@intel.com --- .../processor_thermal_device.h | 2 +- .../int340x_thermal/processor_thermal_mbox.c | 22 +++++++++++-------- .../int340x_thermal/processor_thermal_rfim.c | 10 ++++----- 3 files changed, 19 insertions(+), 15 deletions(-)
diff --git a/drivers/thermal/intel/int340x_thermal/processor_thermal_device.h b/drivers/thermal/intel/int340x_thermal/processor_thermal_device.h index c1d8de6dc3d1..be27f633e40a 100644 --- a/drivers/thermal/intel/int340x_thermal/processor_thermal_device.h +++ b/drivers/thermal/intel/int340x_thermal/processor_thermal_device.h @@ -80,7 +80,7 @@ void proc_thermal_rfim_remove(struct pci_dev *pdev); int proc_thermal_mbox_add(struct pci_dev *pdev, struct proc_thermal_device *proc_priv); void proc_thermal_mbox_remove(struct pci_dev *pdev);
-int processor_thermal_send_mbox_cmd(struct pci_dev *pdev, u16 cmd_id, u32 cmd_data, u32 *cmd_resp); +int processor_thermal_send_mbox_cmd(struct pci_dev *pdev, u16 cmd_id, u32 cmd_data, u64 *cmd_resp); int proc_thermal_add(struct device *dev, struct proc_thermal_device *priv); void proc_thermal_remove(struct proc_thermal_device *proc_priv); int proc_thermal_suspend(struct device *dev); diff --git a/drivers/thermal/intel/int340x_thermal/processor_thermal_mbox.c b/drivers/thermal/intel/int340x_thermal/processor_thermal_mbox.c index 66cd0190bc03..01008ae00e7f 100644 --- a/drivers/thermal/intel/int340x_thermal/processor_thermal_mbox.c +++ b/drivers/thermal/intel/int340x_thermal/processor_thermal_mbox.c @@ -24,7 +24,7 @@
static DEFINE_MUTEX(mbox_lock);
-static int send_mbox_cmd(struct pci_dev *pdev, u16 cmd_id, u32 cmd_data, u32 *cmd_resp) +static int send_mbox_cmd(struct pci_dev *pdev, u16 cmd_id, u32 cmd_data, u64 *cmd_resp) { struct proc_thermal_device *proc_priv; u32 retries, data; @@ -69,12 +69,16 @@ static int send_mbox_cmd(struct pci_dev *pdev, u16 cmd_id, u32 cmd_data, u32 *cm goto unlock_mbox; }
- if (cmd_id == MBOX_CMD_WORKLOAD_TYPE_READ) { - data = readl((void __iomem *) (proc_priv->mmio_base + MBOX_OFFSET_DATA)); - *cmd_resp = data & 0xff; - } - ret = 0; + + if (!cmd_resp) + break; + + if (cmd_id == MBOX_CMD_WORKLOAD_TYPE_READ) + *cmd_resp = readl((void __iomem *) (proc_priv->mmio_base + MBOX_OFFSET_DATA)); + else + *cmd_resp = readq((void __iomem *) (proc_priv->mmio_base + MBOX_OFFSET_DATA)); + break; } while (--retries);
@@ -83,7 +87,7 @@ static int send_mbox_cmd(struct pci_dev *pdev, u16 cmd_id, u32 cmd_data, u32 *cm return ret; }
-int processor_thermal_send_mbox_cmd(struct pci_dev *pdev, u16 cmd_id, u32 cmd_data, u32 *cmd_resp) +int processor_thermal_send_mbox_cmd(struct pci_dev *pdev, u16 cmd_id, u32 cmd_data, u64 *cmd_resp) { return send_mbox_cmd(pdev, cmd_id, cmd_data, cmd_resp); } @@ -154,7 +158,7 @@ static ssize_t workload_type_show(struct device *dev, char *buf) { struct pci_dev *pdev = to_pci_dev(dev); - u32 cmd_resp; + u64 cmd_resp; int ret;
ret = send_mbox_cmd(pdev, MBOX_CMD_WORKLOAD_TYPE_READ, 0, &cmd_resp); @@ -188,7 +192,7 @@ static bool workload_req_created;
int proc_thermal_mbox_add(struct pci_dev *pdev, struct proc_thermal_device *proc_priv) { - u32 cmd_resp; + u64 cmd_resp; int ret;
/* Check if there is a mailbox support, if fails return success */ diff --git a/drivers/thermal/intel/int340x_thermal/processor_thermal_rfim.c b/drivers/thermal/intel/int340x_thermal/processor_thermal_rfim.c index 3b3e81f99a34..e693ec8234fb 100644 --- a/drivers/thermal/intel/int340x_thermal/processor_thermal_rfim.c +++ b/drivers/thermal/intel/int340x_thermal/processor_thermal_rfim.c @@ -195,7 +195,7 @@ static ssize_t rfi_restriction_store(struct device *dev, const char *buf, size_t count) { u16 cmd_id = 0x0008; - u32 cmd_resp; + u64 cmd_resp; u32 input; int ret;
@@ -215,14 +215,14 @@ static ssize_t rfi_restriction_show(struct device *dev, char *buf) { u16 cmd_id = 0x0007; - u32 cmd_resp; + u64 cmd_resp; int ret;
ret = processor_thermal_send_mbox_cmd(to_pci_dev(dev), cmd_id, 0, &cmd_resp); if (ret) return ret;
- return sprintf(buf, "%u\n", cmd_resp); + return sprintf(buf, "%llu\n", cmd_resp); }
static ssize_t ddr_data_rate_show(struct device *dev, @@ -230,14 +230,14 @@ static ssize_t ddr_data_rate_show(struct device *dev, char *buf) { u16 cmd_id = 0x0107; - u32 cmd_resp; + u64 cmd_resp; int ret;
ret = processor_thermal_send_mbox_cmd(to_pci_dev(dev), cmd_id, 0, &cmd_resp); if (ret) return ret;
- return sprintf(buf, "%u\n", cmd_resp); + return sprintf(buf, "%llu\n", cmd_resp); }
static DEVICE_ATTR_RW(rfi_restriction);
From: Arnd Bergmann arnd@arndb.de
32-bit processors cannot generally access 64-bit MMIO registers atomically, and it is unknown in which order the two halves of this registers would need to be read:
drivers/thermal/intel/int340x_thermal/processor_thermal_mbox.c: In function 'send_mbox_cmd': drivers/thermal/intel/int340x_thermal/processor_thermal_mbox.c:79:37: error: implicit declaration of function 'readq'; did you mean 'readl'? [-Werror=implicit-function-declaration] 79 | *cmd_resp = readq((void __iomem *) (proc_priv->mmio_base + MBOX_OFFSET_DATA)); | ^~~~~ | readl
The driver already does not build for anything other than x86, so limit it further to x86-64.
Fixes: aeb58c860dc5 ("thermal/drivers/int340x: processor_thermal: Suppot 64 bit RFIM responses") Signed-off-by: Arnd Bergmann arnd@arndb.de Reviewed-by: Srinivas Pandruvada srinivas.pandruvada@linux.intel.com Reviewed-by: Randy Dunlap rdunlap@infradead.org Signed-off-by: Rafael J. Wysocki rafael.j.wysocki@intel.com Signed-off-by: Sumeet Pawnikar sumeet.r.pawnikar@intel.com --- drivers/thermal/intel/int340x_thermal/Kconfig | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/thermal/intel/int340x_thermal/Kconfig b/drivers/thermal/intel/int340x_thermal/Kconfig index 45c31f3d6054..5d046de96a5d 100644 --- a/drivers/thermal/intel/int340x_thermal/Kconfig +++ b/drivers/thermal/intel/int340x_thermal/Kconfig @@ -5,12 +5,12 @@
config INT340X_THERMAL tristate "ACPI INT340X thermal drivers" - depends on X86 && ACPI && PCI + depends on X86_64 && ACPI && PCI select THERMAL_GOV_USER_SPACE select ACPI_THERMAL_REL select ACPI_FAN select INTEL_SOC_DTS_IOSF_CORE - select PROC_THERMAL_MMIO_RAPL if X86_64 && POWERCAP + select PROC_THERMAL_MMIO_RAPL if POWERCAP help Newer laptops and tablets that use ACPI may have thermal sensors and other devices with thermal control capabilities outside the core
The existing mail mechanism only supports writing of workload types.
However, mailbox command for RFIM (cmd = 0x08) also requires write operation which is ignored. This results in failing to store RFI restriction.
Fixint this requires enhancing mailbox writes for non workload commands too, so remove the check for MBOX_CMD_WORKLOAD_TYPE_WRITE in mailbox write to allow this other write commands to be supoorted.
At the same time, however, we have to make sure that there is no impact on read commands, by avoiding to write anything into the mailbox data register.
To properly implement that, add two separate functions for mbox read and write commands for the processor thermal workload command type. This helps to distinguish the read and write workload command types from each other while sending mbox commands.
Fixes: 5d6fbc96bd36 ("thermal/drivers/int340x: processor_thermal: Export additional attributes") Signed-off-by: Sumeet Pawnikar sumeet.r.pawnikar@intel.com Cc: 5.14+ stable@vger.kernel.org # 5.14+ Acked-by: Srinivas Pandruvada srinivas.pandruvada@linux.intel.com [ rjw: Changelog edits ] Signed-off-by: Rafael J. Wysocki rafael.j.wysocki@intel.com --- .../processor_thermal_device.h | 3 +- .../int340x_thermal/processor_thermal_mbox.c | 100 +++++++++++------- .../int340x_thermal/processor_thermal_rfim.c | 23 ++-- 3 files changed, 73 insertions(+), 53 deletions(-)
diff --git a/drivers/thermal/intel/int340x_thermal/processor_thermal_device.h b/drivers/thermal/intel/int340x_thermal/processor_thermal_device.h index be27f633e40a..9b2a64ef55d0 100644 --- a/drivers/thermal/intel/int340x_thermal/processor_thermal_device.h +++ b/drivers/thermal/intel/int340x_thermal/processor_thermal_device.h @@ -80,7 +80,8 @@ void proc_thermal_rfim_remove(struct pci_dev *pdev); int proc_thermal_mbox_add(struct pci_dev *pdev, struct proc_thermal_device *proc_priv); void proc_thermal_mbox_remove(struct pci_dev *pdev);
-int processor_thermal_send_mbox_cmd(struct pci_dev *pdev, u16 cmd_id, u32 cmd_data, u64 *cmd_resp); +int processor_thermal_send_mbox_read_cmd(struct pci_dev *pdev, u16 id, u64 *resp); +int processor_thermal_send_mbox_write_cmd(struct pci_dev *pdev, u16 id, u32 data); int proc_thermal_add(struct device *dev, struct proc_thermal_device *priv); void proc_thermal_remove(struct proc_thermal_device *proc_priv); int proc_thermal_suspend(struct device *dev); diff --git a/drivers/thermal/intel/int340x_thermal/processor_thermal_mbox.c b/drivers/thermal/intel/int340x_thermal/processor_thermal_mbox.c index 01008ae00e7f..0b89a4340ff4 100644 --- a/drivers/thermal/intel/int340x_thermal/processor_thermal_mbox.c +++ b/drivers/thermal/intel/int340x_thermal/processor_thermal_mbox.c @@ -24,19 +24,15 @@
static DEFINE_MUTEX(mbox_lock);
-static int send_mbox_cmd(struct pci_dev *pdev, u16 cmd_id, u32 cmd_data, u64 *cmd_resp) +static int wait_for_mbox_ready(struct proc_thermal_device *proc_priv) { - struct proc_thermal_device *proc_priv; u32 retries, data; int ret;
- mutex_lock(&mbox_lock); - proc_priv = pci_get_drvdata(pdev); - /* Poll for rb bit == 0 */ retries = MBOX_RETRY_COUNT; do { - data = readl((void __iomem *) (proc_priv->mmio_base + MBOX_OFFSET_INTERFACE)); + data = readl(proc_priv->mmio_base + MBOX_OFFSET_INTERFACE); if (data & BIT_ULL(MBOX_BUSY_BIT)) { ret = -EBUSY; continue; @@ -45,53 +41,78 @@ static int send_mbox_cmd(struct pci_dev *pdev, u16 cmd_id, u32 cmd_data, u64 *cm break; } while (--retries);
+ return ret; +} + +static int send_mbox_write_cmd(struct pci_dev *pdev, u16 id, u32 data) +{ + struct proc_thermal_device *proc_priv; + u32 reg_data; + int ret; + + proc_priv = pci_get_drvdata(pdev); + + mutex_lock(&mbox_lock); + + ret = wait_for_mbox_ready(proc_priv); if (ret) goto unlock_mbox;
- if (cmd_id == MBOX_CMD_WORKLOAD_TYPE_WRITE) - writel(cmd_data, (void __iomem *) ((proc_priv->mmio_base + MBOX_OFFSET_DATA))); - + writel(data, (proc_priv->mmio_base + MBOX_OFFSET_DATA)); /* Write command register */ - data = BIT_ULL(MBOX_BUSY_BIT) | cmd_id; - writel(data, (void __iomem *) ((proc_priv->mmio_base + MBOX_OFFSET_INTERFACE))); + reg_data = BIT_ULL(MBOX_BUSY_BIT) | id; + writel(reg_data, (proc_priv->mmio_base + MBOX_OFFSET_INTERFACE));
- /* Poll for rb bit == 0 */ - retries = MBOX_RETRY_COUNT; - do { - data = readl((void __iomem *) (proc_priv->mmio_base + MBOX_OFFSET_INTERFACE)); - if (data & BIT_ULL(MBOX_BUSY_BIT)) { - ret = -EBUSY; - continue; - } + ret = wait_for_mbox_ready(proc_priv);
- if (data) { - ret = -ENXIO; - goto unlock_mbox; - } +unlock_mbox: + mutex_unlock(&mbox_lock); + return ret; +}
- ret = 0; +static int send_mbox_read_cmd(struct pci_dev *pdev, u16 id, u64 *resp) +{ + struct proc_thermal_device *proc_priv; + u32 reg_data; + int ret;
- if (!cmd_resp) - break; + proc_priv = pci_get_drvdata(pdev);
- if (cmd_id == MBOX_CMD_WORKLOAD_TYPE_READ) - *cmd_resp = readl((void __iomem *) (proc_priv->mmio_base + MBOX_OFFSET_DATA)); - else - *cmd_resp = readq((void __iomem *) (proc_priv->mmio_base + MBOX_OFFSET_DATA)); + mutex_lock(&mbox_lock);
- break; - } while (--retries); + ret = wait_for_mbox_ready(proc_priv); + if (ret) + goto unlock_mbox; + + /* Write command register */ + reg_data = BIT_ULL(MBOX_BUSY_BIT) | id; + writel(reg_data, (proc_priv->mmio_base + MBOX_OFFSET_INTERFACE)); + + ret = wait_for_mbox_ready(proc_priv); + if (ret) + goto unlock_mbox; + + if (id == MBOX_CMD_WORKLOAD_TYPE_READ) + *resp = readl(proc_priv->mmio_base + MBOX_OFFSET_DATA); + else + *resp = readq(proc_priv->mmio_base + MBOX_OFFSET_DATA);
unlock_mbox: mutex_unlock(&mbox_lock); return ret; }
-int processor_thermal_send_mbox_cmd(struct pci_dev *pdev, u16 cmd_id, u32 cmd_data, u64 *cmd_resp) +int processor_thermal_send_mbox_read_cmd(struct pci_dev *pdev, u16 id, u64 *resp) { - return send_mbox_cmd(pdev, cmd_id, cmd_data, cmd_resp); + return send_mbox_read_cmd(pdev, id, resp); } -EXPORT_SYMBOL_GPL(processor_thermal_send_mbox_cmd); +EXPORT_SYMBOL_NS_GPL(processor_thermal_send_mbox_read_cmd, INT340X_THERMAL); + +int processor_thermal_send_mbox_write_cmd(struct pci_dev *pdev, u16 id, u32 data) +{ + return send_mbox_write_cmd(pdev, id, data); +} +EXPORT_SYMBOL_NS_GPL(processor_thermal_send_mbox_write_cmd, INT340X_THERMAL);
/* List of workload types */ static const char * const workload_types[] = { @@ -104,7 +125,6 @@ static const char * const workload_types[] = { NULL };
- static ssize_t workload_available_types_show(struct device *dev, struct device_attribute *attr, char *buf) @@ -146,7 +166,7 @@ static ssize_t workload_type_store(struct device *dev,
data |= ret;
- ret = send_mbox_cmd(pdev, MBOX_CMD_WORKLOAD_TYPE_WRITE, data, NULL); + ret = send_mbox_write_cmd(pdev, MBOX_CMD_WORKLOAD_TYPE_WRITE, data); if (ret) return false;
@@ -161,7 +181,7 @@ static ssize_t workload_type_show(struct device *dev, u64 cmd_resp; int ret;
- ret = send_mbox_cmd(pdev, MBOX_CMD_WORKLOAD_TYPE_READ, 0, &cmd_resp); + ret = send_mbox_read_cmd(pdev, MBOX_CMD_WORKLOAD_TYPE_READ, &cmd_resp); if (ret) return false;
@@ -186,8 +206,6 @@ static const struct attribute_group workload_req_attribute_group = { .name = "workload_request" };
- - static bool workload_req_created;
int proc_thermal_mbox_add(struct pci_dev *pdev, struct proc_thermal_device *proc_priv) @@ -196,7 +214,7 @@ int proc_thermal_mbox_add(struct pci_dev *pdev, struct proc_thermal_device *proc int ret;
/* Check if there is a mailbox support, if fails return success */ - ret = send_mbox_cmd(pdev, MBOX_CMD_WORKLOAD_TYPE_READ, 0, &cmd_resp); + ret = send_mbox_read_cmd(pdev, MBOX_CMD_WORKLOAD_TYPE_READ, &cmd_resp); if (ret) return 0;
diff --git a/drivers/thermal/intel/int340x_thermal/processor_thermal_rfim.c b/drivers/thermal/intel/int340x_thermal/processor_thermal_rfim.c index e693ec8234fb..8c42e7662033 100644 --- a/drivers/thermal/intel/int340x_thermal/processor_thermal_rfim.c +++ b/drivers/thermal/intel/int340x_thermal/processor_thermal_rfim.c @@ -9,6 +9,8 @@ #include <linux/pci.h> #include "processor_thermal_device.h"
+MODULE_IMPORT_NS(INT340X_THERMAL); + struct mmio_reg { int read_only; u32 offset; @@ -194,8 +196,7 @@ static ssize_t rfi_restriction_store(struct device *dev, struct device_attribute *attr, const char *buf, size_t count) { - u16 cmd_id = 0x0008; - u64 cmd_resp; + u16 id = 0x0008; u32 input; int ret;
@@ -203,7 +204,7 @@ static ssize_t rfi_restriction_store(struct device *dev, if (ret) return ret;
- ret = processor_thermal_send_mbox_cmd(to_pci_dev(dev), cmd_id, input, &cmd_resp); + ret = processor_thermal_send_mbox_write_cmd(to_pci_dev(dev), id, input); if (ret) return ret;
@@ -214,30 +215,30 @@ static ssize_t rfi_restriction_show(struct device *dev, struct device_attribute *attr, char *buf) { - u16 cmd_id = 0x0007; - u64 cmd_resp; + u16 id = 0x0007; + u64 resp; int ret;
- ret = processor_thermal_send_mbox_cmd(to_pci_dev(dev), cmd_id, 0, &cmd_resp); + ret = processor_thermal_send_mbox_read_cmd(to_pci_dev(dev), id, &resp); if (ret) return ret;
- return sprintf(buf, "%llu\n", cmd_resp); + return sprintf(buf, "%llu\n", resp); }
static ssize_t ddr_data_rate_show(struct device *dev, struct device_attribute *attr, char *buf) { - u16 cmd_id = 0x0107; - u64 cmd_resp; + u16 id = 0x0107; + u64 resp; int ret;
- ret = processor_thermal_send_mbox_cmd(to_pci_dev(dev), cmd_id, 0, &cmd_resp); + ret = processor_thermal_send_mbox_read_cmd(to_pci_dev(dev), id, &resp); if (ret) return ret;
- return sprintf(buf, "%llu\n", cmd_resp); + return sprintf(buf, "%llu\n", resp); }
static DEVICE_ATTR_RW(rfi_restriction);
linux-stable-mirror@lists.linaro.org
-
Greg KH -
Pawnikar, Sumeet R -
Sumeet Pawnikar