stable v6.6.24 regression: boot fails: bisected to "x86/mpparse: Register APIC address only once"
Hello,
after upgrading to v6.6.24 from v6.6.23 some old boxes (i686; Intel Celeron M) stop to boot:
They hang after:
Decompressing Linux... Parsing ELF... No relocation needed... done. Booting the kernel (entry_offset: 0x00000000).
After some minutes they reboot.
I bisected this down to
commit bebb5af001dc6cb4f505bb21c4d5e2efbdc112e2 Author: Thomas Gleixner tglx@linutronix.de Date: Fri Mar 22 19:56:39 2024 +0100
x86/mpparse: Register APIC address only once
[ Upstream commit f2208aa12c27bfada3c15c550c03ca81d42dcac2 ]
The APIC address is registered twice. First during the early detection and afterwards when actually scanning the table for APIC IDs. The APIC and topology core warn about the second attempt.
Restrict it to the early detection call.
Fixes: 81287ad65da5 ("x86/apic: Sanitize APIC address setup") Signed-off-by: Thomas Gleixner tglx@linutronix.de Signed-off-by: Borislav Petkov (AMD) bp@alien8.de Tested-by: Guenter Roeck linux@roeck-us.net Link: https://lore.kernel.org/r/20240322185305.297774848@linutronix.de Signed-off-by: Sasha Levin sashal@kernel.org
Reverting this commit in v6.6.24 solves the problem.
Regards,
On Thu, Apr 04, 2024 at 02:07:11PM +0200, Wolfgang Walter wrote:
Hello,
after upgrading to v6.6.24 from v6.6.23 some old boxes (i686; Intel Celeron M) stop to boot:
They hang after:
Decompressing Linux... Parsing ELF... No relocation needed... done. Booting the kernel (entry_offset: 0x00000000).
After some minutes they reboot.
I bisected this down to
commit bebb5af001dc6cb4f505bb21c4d5e2efbdc112e2 Author: Thomas Gleixner tglx@linutronix.de Date: Fri Mar 22 19:56:39 2024 +0100
x86/mpparse: Register APIC address only once [ Upstream commit f2208aa12c27bfada3c15c550c03ca81d42dcac2 ] The APIC address is registered twice. First during the early detectionand afterwards when actually scanning the table for APIC IDs. The APIC and topology core warn about the second attempt.
Restrict it to the early detection call. Fixes: 81287ad65da5 ("x86/apic: Sanitize APIC address setup") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Tested-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20240322185305.297774848@linutronix.de Signed-off-by: Sasha Levin <sashal@kernel.org>Reverting this commit in v6.6.24 solves the problem.
Is this also an issue in 6.9-rc1 or newer or 6.8.3 or newer?
thanks,
greg k-h
On Thu, Apr 04 2024 at 17:57, Greg Kroah-Hartman wrote:
On Thu, Apr 04, 2024 at 02:07:11PM +0200, Wolfgang Walter wrote:
Reverting this commit in v6.6.24 solves the problem.
Is this also an issue in 6.9-rc1 or newer or 6.8.3 or newer?
Also can you please provide the boot dmesg from a working kernel?
Thanks,
tglx
Hello Thomas!
Am 2024-04-05 11:33, schrieb Thomas Gleixner:
On Thu, Apr 04 2024 at 17:57, Greg Kroah-Hartman wrote:
On Thu, Apr 04, 2024 at 02:07:11PM +0200, Wolfgang Walter wrote:
Reverting this commit in v6.6.24 solves the problem.
Is this also an issue in 6.9-rc1 or newer or 6.8.3 or newer?
Also can you please provide the boot dmesg from a working kernel?
Thanks,
tglx
here is the output of dmesg after booting 6.6.24 with the one patch reverted:
[ 0.000000] Linux version 6.6.24-genrouter32.pm+2.19 (root@sid-i386) (gcc (Debian 13.2.0-23) 13.2.0, GNU ld (GNU Binutils for Debian) 2.42) #1 PREEMPT_DYNAMIC Thu Apr 4 13:44:40 CEST 2024 [ 0.000000] Disabled fast string operations [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable [ 0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000003fefffff] usable [ 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fed13000-0x00000000fed19fff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000ffb00000-0x00000000ffffffff] reserved [ 0.000000] Notice: NX (Execute Disable) protection cannot be enabled: non-PAE kernel! [ 0.000000] APIC: Static calls initialized [ 0.000000] SMBIOS 2.3 present. [ 0.000000] DMI: To Be Filled By O.E.M. To Be Filled By O.E.M./To be filled by O.E.M., BIOS 080012 10/16/2008 [ 0.000000] tsc: Fast TSC calibration using PIT [ 0.000000] tsc: Detected 1000.027 MHz processor [ 0.011020] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved [ 0.011031] e820: remove [mem 0x000a0000-0x000fffff] usable [ 0.011047] last_pfn = 0x3ff00 max_arch_pfn = 0x100000 [ 0.011063] MTRR map: 7 entries (5 fixed + 2 variable; max 21), built from 8 variable MTRRs [ 0.011069] x86/PAT: PAT not supported by the CPU. [ 0.011074] x86/PAT: Configuration [0-7]: WB WT UC- UC WB WT UC- UC [ 0.011250] Warning only 887MB will be used. [ 0.011254] Use a HIGHMEM enabled kernel. [ 0.024603] found SMP MP-table at [mem 0x000ff780-0x000ff78f] [ 0.024628] initial memory mapped: [mem 0x00000000-0x023fffff] [ 0.024715] RAMDISK: [mem 0x3a593000-0x3fefffff] [ 0.024720] Allocated new RAMDISK: [mem 0x31e91000-0x377fd9c6] [ 0.189769] Move RAMDISK from [mem 0x3a593000-0x3feff9c6] to [mem 0x31e91000-0x377fd9c6] [ 0.189796] ACPI: Early table checksum verification disabled [ 0.190798] ACPI BIOS Error (bug): A valid RSDP was not found (20230628/tbxfroot-222) [ 0.190822] 887MB LOWMEM available. [ 0.190825] mapped low ram: 0 - 377fe000 [ 0.190828] low ram: 0 - 377fe000 [ 0.190857] Zone ranges: [ 0.190858] DMA [mem 0x0000000000001000-0x0000000000ffffff] [ 0.190864] Normal [mem 0x0000000001000000-0x00000000377fdfff] [ 0.190870] Movable zone start for each node [ 0.190872] Early memory node ranges [ 0.190873] node 0: [mem 0x0000000000001000-0x000000000009efff] [ 0.190879] node 0: [mem 0x0000000000100000-0x000000003fefffff] [ 0.190884] Initmem setup node 0 [mem 0x0000000000001000-0x000000003fefffff] [ 0.190914] On node 0, zone DMA: 1 pages in unavailable ranges [ 0.191188] On node 0, zone DMA: 97 pages in unavailable ranges [ 0.206473] On node 0, zone Normal: 2 pages in unavailable ranges [ 0.206499] Reserving Intel graphics memory at [mem 0x3ff00000-0x3fffffff] [ 0.206783] Intel MultiProcessor Specification v1.4 [ 0.206786] Virtual Wire compatibility mode. [ 0.206792] MPTABLE: OEM ID: Intel [ 0.206794] MPTABLE: Product ID: Alviso [ 0.206796] MPTABLE: APIC at: 0xFEE00000 [ 0.206805] Processor #0 (Bootup-CPU) [ 0.206818] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23 [ 0.206833] Processors: 1 [ 0.206865] [mem 0x40000000-0xdfffffff] available for PCI devices [ 0.206876] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370452778343963 ns [ 0.206955] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.206969] pcpu-alloc: [0] 0 [ 0.206998] Kernel command line: BOOT_IMAGE=kernel initrd=system.gz init=/sbin/init ipv6.disable=1 dummy.numdummies=16 ide-core.nodma=1.0 iommu=pt libata.dma=3 random.trust_cpu=on reboot=cold,force retbleed=off rootfstype=ramfs [ 0.207970] Unknown kernel command line parameters "BOOT_IMAGE=kernel", will be passed to user space. [ 0.208454] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.208743] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.208817] Built 1 zonelists, mobility grouping on. Total pages: 225008 [ 0.208827] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.224800] Checking if this processor honours the WP bit even in supervisor mode...Ok. [ 0.224824] Memory: 789268K/908912K available (12924K kernel code, 734K rwdata, 3016K rodata, 640K init, 272K bss, 119644K reserved, 0K cma-reserved) [ 0.272716] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.274031] Dynamic Preempt: full [ 0.274441] rcu: Preemptible hierarchical RCU implementation. [ 0.274446] Trampoline variant of Tasks RCU enabled. [ 0.274448] Tracing variant of Tasks RCU enabled. [ 0.274451] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies. [ 0.274474] NR_IRQS: 2304, nr_irqs: 48, preallocated irqs: 16 [ 0.274818] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.279294] Console: colour VGA+ 80x25 [ 0.279304] printk: console [tty0] enabled [ 0.284538] APIC: Switch to symmetric I/O mode setup [ 0.284675] ExtINT not setup in hardware but reported by MP table [ 0.285172] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=0 pin2=0 [ 0.301203] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0xe6a309e20b, max_idle_ns: 440795251594 ns [ 0.301330] Calibrating delay loop (skipped), value calculated using timer frequency.. 2000.38 BogoMIPS (lpj=3333423) [ 0.301454] Disabled fast string operations [ 0.301543] CPU0: Thermal monitoring enabled (TM1) [ 0.301653] Last level iTLB entries: 4KB 128, 2MB 0, 4MB 2 [ 0.301724] Last level dTLB entries: 4KB 128, 2MB 0, 4MB 8, 1GB 0 [ 0.301801] CPU: Intel(R) Celeron(R) M processor 1.00GHz (family: 0x6, model: 0xd, stepping: 0x8) [ 0.301908] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization [ 0.302009] Spectre V2 : Mitigation: Retpolines [ 0.302073] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch [ 0.302167] Spectre V2 : Spectre v2 / SpectreRSB : Filling RSB on VMEXIT [ 0.302257] Speculative Store Bypass: Vulnerable [ 0.302321] L1TF: Kernel not compiled for PAE. No mitigation for L1TF [ 0.302391] MDS: Vulnerable: Clear CPU buffers attempted, no microcode [ 0.302482] MMIO Stale Data: Unknown: No mitigations [ 0.302551] x86/fpu: x87 FPU will use FXSAVE [ 0.303967] pid_max: default: 32768 minimum: 301 [ 0.310878] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.310983] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.317030] RCU Tasks: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1. [ 0.317213] RCU Tasks Trace: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1. [ 0.317365] Performance Events: p6 PMU driver. [ 0.317442] ... version: 0 [ 0.317506] ... bit width: 32 [ 0.317568] ... generic registers: 2 [ 0.317630] ... value mask: 00000000ffffffff [ 0.317697] ... max period: 000000007fffffff [ 0.317764] ... fixed-purpose events: 0 [ 0.317826] ... event mask: 0000000000000003 [ 0.318055] signal: max sigframe size: 1440 [ 0.318218] rcu: Hierarchical SRCU implementation. [ 0.318286] rcu: Max phase no-delay instances is 1000. [ 0.532964] devtmpfs: initialized [ 0.534649] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns [ 0.534649] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.536674] pinctrl core: initialized pinctrl subsystem [ 0.537989] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.539307] thermal_sys: Registered thermal governor 'fair_share' [ 0.539314] thermal_sys: Registered thermal governor 'bang_bang' [ 0.539387] thermal_sys: Registered thermal governor 'step_wise' [ 0.539455] thermal_sys: Registered thermal governor 'user_space' [ 0.539570] cpuidle: using governor ladder [ 0.542249] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=5 [ 0.542330] PCI: Using configuration type 1 for base access [ 0.544781] cryptd: max_cpu_qlen set to 1000 [ 0.547865] ACPI: Interpreter disabled. [ 0.548015] iommu: Default domain type: Passthrough (set via kernel command line) [ 0.548511] SCSI subsystem initialized [ 0.548741] libata version 3.00 loaded. [ 0.548905] usbcore: registered new interface driver usbfs [ 0.548996] usbcore: registered new interface driver hub [ 0.549083] usbcore: registered new device driver usb [ 0.549268] pps_core: LinuxPPS API ver. 1 registered [ 0.549336] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti giometti@linux.it [ 0.549443] PTP clock support registered [ 0.549535] EDAC MC: Ver: 3.0.0 [ 0.550594] PCI: Probing PCI hardware [ 0.550666] PCI: root bus 00: using default resources [ 0.550671] PCI: Probing PCI hardware (bus 00) [ 0.550720] PCI host bridge to bus 0000:00 [ 0.550789] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 0.550864] pci_bus 0000:00: root bus resource [mem 0x00000000-0xffffffff] [ 0.550958] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.551076] pci 0000:00:00.0: [8086:2590] type 00 class 0x060000 [ 0.551362] pci 0000:00:02.0: [8086:2592] type 00 class 0x030000 [ 0.551449] pci 0000:00:02.0: reg 0x10: [mem 0xfe680000-0xfe6fffff] [ 0.551527] pci 0000:00:02.0: reg 0x14: [io 0x9c00-0x9c07] [ 0.551603] pci 0000:00:02.0: reg 0x18: [mem 0xd0000000-0xdfffffff pref] [ 0.554659] pci 0000:00:02.0: reg 0x1c: [mem 0xfe640000-0xfe67ffff] [ 0.554758] pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff] [ 0.554961] pci 0000:00:02.1: [8086:2792] type 00 class 0x038000 [ 0.555047] pci 0000:00:02.1: reg 0x10: [mem 0xfe580000-0xfe5fffff] [ 0.555311] pci 0000:00:1c.0: [8086:2660] type 01 class 0x060400 [ 0.555434] pci 0000:00:1c.0: enabling Extended Tags [ 0.555547] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold [ 0.555759] pci 0000:00:1c.1: [8086:2662] type 01 class 0x060400 [ 0.555880] pci 0000:00:1c.1: enabling Extended Tags [ 0.555992] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold [ 0.556170] pci 0000:00:1c.2: [8086:2664] type 01 class 0x060400 [ 0.556290] pci 0000:00:1c.2: enabling Extended Tags [ 0.556400] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold [ 0.556593] pci 0000:00:1c.3: [8086:2666] type 01 class 0x060400 [ 0.556713] pci 0000:00:1c.3: enabling Extended Tags [ 0.556824] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold [ 0.557018] pci 0000:00:1d.0: [8086:2658] type 00 class 0x0c0300 [ 0.557140] pci 0000:00:1d.0: reg 0x20: [io 0x9880-0x989f] [ 0.557333] pci 0000:00:1d.7: [8086:265c] type 00 class 0x0c0320 [ 0.557424] pci 0000:00:1d.7: reg 0x10: [mem 0xfe63bc00-0xfe63bfff] [ 0.558142] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold [ 0.558333] pci 0000:00:1e.0: [8086:2448] type 01 class 0x060401 [ 0.558556] pci 0000:00:1f.0: [8086:2641] type 00 class 0x060100 [ 0.558721] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000 [ 0.558734] pci 0000:00:1f.0: quirk: [io 0x0800-0x087f] claimed by ICH6 ACPI/GPIO/TCO [ 0.558835] pci 0000:00:1f.0: quirk: [io 0x0480-0x04bf] claimed by ICH6 GPIO [ 0.558932] pci 0000:00:1f.0: LPC Generic IO decode 2 PIO at 0a00-0a0f [ 0.559142] pci 0000:00:1f.1: [8086:266f] type 00 class 0x01018a [ 0.559234] pci 0000:00:1f.1: reg 0x10: [io 0x0000-0x0007] [ 0.559314] pci 0000:00:1f.1: reg 0x14: [io 0x0000-0x0003] [ 0.559391] pci 0000:00:1f.1: reg 0x18: [io 0x0000-0x0007] [ 0.559468] pci 0000:00:1f.1: reg 0x1c: [io 0x0000-0x0003] [ 0.559546] pci 0000:00:1f.1: reg 0x20: [io 0xffa0-0xffaf] [ 0.559636] pci 0000:00:1f.1: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7] [ 0.559730] pci 0000:00:1f.1: legacy IDE quirk: reg 0x14: [io 0x03f6] [ 0.559822] pci 0000:00:1f.1: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177] [ 0.559917] pci 0000:00:1f.1: legacy IDE quirk: reg 0x1c: [io 0x0376] [ 0.560131] pci 0000:00:1f.2: [8086:2653] type 00 class 0x01018f [ 0.560220] pci 0000:00:1f.2: reg 0x10: [io 0x9800-0x9807] [ 0.560298] pci 0000:00:1f.2: reg 0x14: [io 0x9480-0x9483] [ 0.560375] pci 0000:00:1f.2: reg 0x18: [io 0x9400-0x9407] [ 0.560452] pci 0000:00:1f.2: reg 0x1c: [io 0x9080-0x9083] [ 0.560529] pci 0000:00:1f.2: reg 0x20: [io 0x9000-0x900f] [ 0.560605] pci 0000:00:1f.2: reg 0x24: [mem 0xfe63b800-0xfe63bbff] [ 0.560712] pci 0000:00:1f.2: PME# supported from D3hot [ 0.560871] pci 0000:00:1f.3: [8086:266a] type 00 class 0x0c0500 [ 0.561003] pci 0000:00:1f.3: reg 0x20: [io 0x0400-0x041f] [ 0.561289] pci 0000:01:00.0: [8086:109a] type 00 class 0x020000 [ 0.561352] pci 0000:01:00.0: reg 0x10: [mem 0xfe7e0000-0xfe7fffff] [ 0.561459] pci 0000:01:00.0: reg 0x18: [io 0xac00-0xac1f] [ 0.561683] pci 0000:01:00.0: PME# supported from D0 D3hot [ 0.561870] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' [ 0.561995] pci 0000:00:1c.0: PCI bridge to [bus 01] [ 0.562067] pci 0000:00:1c.0: bridge window [io 0xa000-0xafff] [ 0.562141] pci 0000:00:1c.0: bridge window [mem 0xfe700000-0xfe7fffff] [ 0.562366] pci 0000:02:00.0: [8086:109a] type 00 class 0x020000 [ 0.562473] pci 0000:02:00.0: reg 0x10: [mem 0xfe8e0000-0xfe8fffff] [ 0.562579] pci 0000:02:00.0: reg 0x18: [io 0xbc00-0xbc1f] [ 0.562801] pci 0000:02:00.0: PME# supported from D0 D3hot [ 0.563008] pci 0000:02:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' [ 0.563133] pci 0000:00:1c.1: PCI bridge to [bus 02] [ 0.563204] pci 0000:00:1c.1: bridge window [io 0xb000-0xbfff] [ 0.563277] pci 0000:00:1c.1: bridge window [mem 0xfe800000-0xfe8fffff] [ 0.563465] pci 0000:03:00.0: [8086:109a] type 00 class 0x020000 [ 0.563571] pci 0000:03:00.0: reg 0x10: [mem 0xfe9e0000-0xfe9fffff] [ 0.563676] pci 0000:03:00.0: reg 0x18: [io 0xcc00-0xcc1f] [ 0.563900] pci 0000:03:00.0: PME# supported from D0 D3hot [ 0.564102] pci 0000:03:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' [ 0.564226] pci 0000:00:1c.2: PCI bridge to [bus 03] [ 0.564297] pci 0000:00:1c.2: bridge window [io 0xc000-0xcfff] [ 0.564369] pci 0000:00:1c.2: bridge window [mem 0xfe900000-0xfe9fffff] [ 0.564556] pci 0000:04:00.0: [8086:109a] type 00 class 0x020000 [ 0.564684] pci 0000:04:00.0: reg 0x10: [mem 0xfeae0000-0xfeafffff] [ 0.564791] pci 0000:04:00.0: reg 0x18: [io 0xdc00-0xdc1f] [ 0.565014] pci 0000:04:00.0: PME# supported from D0 D3hot [ 0.565224] pci 0000:04:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' [ 0.565349] pci 0000:00:1c.3: PCI bridge to [bus 04] [ 0.565420] pci 0000:00:1c.3: bridge window [io 0xd000-0xdfff] [ 0.565493] pci 0000:00:1c.3: bridge window [mem 0xfea00000-0xfeafffff] [ 0.565612] pci_bus 0000:05: extended config space not accessible [ 0.565729] pci 0000:05:02.0: [8086:1229] type 00 class 0x020000 [ 0.565820] pci 0000:05:02.0: reg 0x10: [mem 0xfebff000-0xfebfffff] [ 0.565901] pci 0000:05:02.0: reg 0x14: [io 0xec00-0xec3f] [ 0.565980] pci 0000:05:02.0: reg 0x18: [mem 0xfebc0000-0xfebdffff] [ 0.566086] pci 0000:05:02.0: reg 0x30: [mem 0xfebe0000-0xfebeffff pref] [ 0.566213] pci 0000:05:02.0: supports D1 D2 [ 0.566278] pci 0000:05:02.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.566485] pci 0000:05:03.0: [8086:1229] type 00 class 0x020000 [ 0.566577] pci 0000:05:03.0: reg 0x10: [mem 0xfebfe000-0xfebfefff] [ 0.566659] pci 0000:05:03.0: reg 0x14: [io 0xe880-0xe8bf] [ 0.566737] pci 0000:05:03.0: reg 0x18: [mem 0xfeba0000-0xfebbffff] [ 0.566844] pci 0000:05:03.0: reg 0x30: [mem 0xfeb90000-0xfeb9ffff pref] [ 0.566967] pci 0000:05:03.0: supports D1 D2 [ 0.567032] pci 0000:05:03.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.567232] pci 0000:05:04.0: [8086:1229] type 00 class 0x020000 [ 0.567324] pci 0000:05:04.0: reg 0x10: [mem 0xfebfd000-0xfebfdfff] [ 0.567406] pci 0000:05:04.0: reg 0x14: [io 0xe800-0xe83f] [ 0.567484] pci 0000:05:04.0: reg 0x18: [mem 0xfeb60000-0xfeb7ffff] [ 0.567590] pci 0000:05:04.0: reg 0x30: [mem 0xfeb80000-0xfeb8ffff pref] [ 0.567713] pci 0000:05:04.0: supports D1 D2 [ 0.567778] pci 0000:05:04.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.568054] pci 0000:05:05.0: [8086:1229] type 00 class 0x020000 [ 0.568146] pci 0000:05:05.0: reg 0x10: [mem 0xfebfc000-0xfebfcfff] [ 0.568228] pci 0000:05:05.0: reg 0x14: [io 0xe480-0xe4bf] [ 0.568306] pci 0000:05:05.0: reg 0x18: [mem 0xfeb40000-0xfeb5ffff] [ 0.568413] pci 0000:05:05.0: reg 0x30: [mem 0xfeb30000-0xfeb3ffff pref] [ 0.568537] pci 0000:05:05.0: supports D1 D2 [ 0.568602] pci 0000:05:05.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.568836] pci 0000:00:1e.0: PCI bridge to [bus 05] (subtractive decode) [ 0.568935] pci 0000:00:1e.0: bridge window [io 0xe000-0xefff] [ 0.569008] pci 0000:00:1e.0: bridge window [mem 0xfeb00000-0xfebfffff] [ 0.569105] pci 0000:00:1e.0: bridge window [io 0x0000-0xffff] (subtractive decode) [ 0.569202] pci 0000:00:1e.0: bridge window [mem 0x00000000-0xffffffff] (subtractive decode) [ 0.569330] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 05 [ 0.569488] pci 0000:00:1f.0: PIIX/ICH IRQ router [8086:2641] [ 0.569570] PCI: pci_cache_line_size set to 64 bytes [ 0.569657] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff] [ 0.569664] e820: reserve RAM buffer [mem 0x3ff00000-0x3fffffff] [ 0.569799] pci 0000:00:02.0: vgaarb: setting as boot VGA device [ 0.569874] pci 0000:00:02.0: vgaarb: bridge control possible [ 0.569943] pci 0000:00:02.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none [ 0.570053] vgaarb: loaded [ 0.570802] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484882848 ns [ 0.570918] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 [ 0.570998] hpet0: 3 comparators, 64-bit 14.318180 MHz counter [ 0.572394] clocksource: Switched to clocksource tsc-early [ 0.577309] VFS: Disk quotas dquot_6.6.0 [ 0.577614] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.577809] pnp: PnP ACPI: disabled [ 0.583841] NET: Registered PF_INET protocol family [ 0.584175] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.586329] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.586448] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.586549] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.586690] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.586898] TCP: Hash tables configured (established 8192 bind 8192) [ 0.587063] UDP hash table entries: 512 (order: 1, 8192 bytes, linear) [ 0.587178] UDP-Lite hash table entries: 512 (order: 1, 8192 bytes, linear) [ 0.587743] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.587845] NET: Registered PF_XDP protocol family [ 0.587933] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 01] add_size 200000 add_align 100000 [ 0.588053] pci 0000:00:1c.1: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 02] add_size 200000 add_align 100000 [ 0.591818] pci 0000:00:1c.2: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 03] add_size 200000 add_align 100000 [ 0.591932] pci 0000:00:1c.3: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 04] add_size 200000 add_align 100000 [ 0.592067] pci 0000:00:1c.0: BAR 15: assigned [mem 0x40000000-0x401fffff 64bit pref] [ 0.592170] pci 0000:00:1c.1: BAR 15: assigned [mem 0x40200000-0x403fffff 64bit pref] [ 0.592268] pci 0000:00:1c.2: BAR 15: assigned [mem 0x40400000-0x405fffff 64bit pref] [ 0.592366] pci 0000:00:1c.3: BAR 15: assigned [mem 0x40600000-0x407fffff 64bit pref] [ 0.592468] pci 0000:00:1c.0: PCI bridge to [bus 01] [ 0.592538] pci 0000:00:1c.0: bridge window [io 0xa000-0xafff] [ 0.592615] pci 0000:00:1c.0: bridge window [mem 0xfe700000-0xfe7fffff] [ 0.592711] pci 0000:00:1c.0: bridge window [mem 0x40000000-0x401fffff 64bit pref] [ 0.592818] pci 0000:00:1c.1: PCI bridge to [bus 02] [ 0.592887] pci 0000:00:1c.1: bridge window [io 0xb000-0xbfff] [ 0.592962] pci 0000:00:1c.1: bridge window [mem 0xfe800000-0xfe8fffff] [ 0.593057] pci 0000:00:1c.1: bridge window [mem 0x40200000-0x403fffff 64bit pref] [ 0.593157] pci 0000:00:1c.2: PCI bridge to [bus 03] [ 0.593225] pci 0000:00:1c.2: bridge window [io 0xc000-0xcfff] [ 0.593299] pci 0000:00:1c.2: bridge window [mem 0xfe900000-0xfe9fffff] [ 0.593394] pci 0000:00:1c.2: bridge window [mem 0x40400000-0x405fffff 64bit pref] [ 0.593494] pci 0000:00:1c.3: PCI bridge to [bus 04] [ 0.593562] pci 0000:00:1c.3: bridge window [io 0xd000-0xdfff] [ 0.593636] pci 0000:00:1c.3: bridge window [mem 0xfea00000-0xfeafffff] [ 0.593730] pci 0000:00:1c.3: bridge window [mem 0x40600000-0x407fffff 64bit pref] [ 0.593832] pci 0000:00:1e.0: PCI bridge to [bus 05] [ 0.593901] pci 0000:00:1e.0: bridge window [io 0xe000-0xefff] [ 0.593974] pci 0000:00:1e.0: bridge window [mem 0xfeb00000-0xfebfffff] [ 0.594074] pci_bus 0000:00: resource 4 [io 0x0000-0xffff] [ 0.594144] pci_bus 0000:00: resource 5 [mem 0x00000000-0xffffffff] [ 0.594216] pci_bus 0000:01: resource 0 [io 0xa000-0xafff] [ 0.594285] pci_bus 0000:01: resource 1 [mem 0xfe700000-0xfe7fffff] [ 0.594357] pci_bus 0000:01: resource 2 [mem 0x40000000-0x401fffff 64bit pref] [ 0.594451] pci_bus 0000:02: resource 0 [io 0xb000-0xbfff] [ 0.594520] pci_bus 0000:02: resource 1 [mem 0xfe800000-0xfe8fffff] [ 0.594592] pci_bus 0000:02: resource 2 [mem 0x40200000-0x403fffff 64bit pref] [ 0.594686] pci_bus 0000:03: resource 0 [io 0xc000-0xcfff] [ 0.594755] pci_bus 0000:03: resource 1 [mem 0xfe900000-0xfe9fffff] [ 0.594826] pci_bus 0000:03: resource 2 [mem 0x40400000-0x405fffff 64bit pref] [ 0.594921] pci_bus 0000:04: resource 0 [io 0xd000-0xdfff] [ 0.594990] pci_bus 0000:04: resource 1 [mem 0xfea00000-0xfeafffff] [ 0.595061] pci_bus 0000:04: resource 2 [mem 0x40600000-0x407fffff 64bit pref] [ 0.595156] pci_bus 0000:05: resource 0 [io 0xe000-0xefff] [ 0.595225] pci_bus 0000:05: resource 1 [mem 0xfeb00000-0xfebfffff] [ 0.595297] pci_bus 0000:05: resource 4 [io 0x0000-0xffff] [ 0.595366] pci_bus 0000:05: resource 5 [mem 0x00000000-0xffffffff] [ 0.595510] pci 0000:00:1d.0: PCI->APIC IRQ transform: INT A -> IRQ 23 [ 0.595637] pci 0000:00:1d.7: PCI->APIC IRQ transform: INT A -> IRQ 23 [ 0.622820] pci 0000:00:1d.7: quirk_usb_early_handoff+0x0/0x7b8 took 26553 usecs [ 0.623003] pci 0000:05:02.0: Firmware left e100 interrupts enabled; disabling [ 0.623110] pci 0000:05:03.0: Firmware left e100 interrupts enabled; disabling [ 0.623215] pci 0000:05:04.0: Firmware left e100 interrupts enabled; disabling [ 0.623320] pci 0000:05:05.0: Firmware left e100 interrupts enabled; disabling [ 0.623417] PCI: CLS 64 bytes, default 64 [ 0.624577] Trying to unpack rootfs image as initramfs... [ 0.626321] platform rtc_cmos: registered platform RTC device (no PNP device found) [ 0.627096] PCLMULQDQ-NI instructions are not detected. [ 0.628431] Initialise system trusted keyrings [ 0.628563] Key type blacklist registered [ 0.632913] workingset: timestamp_bits=14 max_order=18 bucket_order=4 [ 0.633032] zbud: loaded [ 0.804584] jitterentropy: Initialization failed with host not compliant with requirements: 9 [ 0.804720] NET: Registered PF_ALG protocol family [ 0.804831] Key type asymmetric registered [ 0.804896] Asymmetric key parser 'x509' registered [ 0.804962] Asymmetric key parser 'pkcs8' registered [ 0.809525] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250) [ 0.809640] io scheduler mq-deadline registered [ 0.809706] io scheduler kyber registered [ 0.810011] io scheduler bfq registered [ 0.810475] xz_dec_test: module loaded [ 0.810541] xz_dec_test: Create a device node with 'mknod xz_dec_test c 249 0' and write .xz files to it. [ 0.810837] pcieport 0000:00:1c.0: PCI->APIC IRQ transform: INT A -> IRQ 16 [ 0.811126] pcieport 0000:00:1c.1: PCI->APIC IRQ transform: INT B -> IRQ 17 [ 0.811342] pcieport 0000:00:1c.2: PCI->APIC IRQ transform: INT C -> IRQ 18 [ 0.811592] pcieport 0000:00:1c.3: PCI->APIC IRQ transform: INT D -> IRQ 19 [ 0.816466] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.856166] serial8250: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A [ 0.862653] intel_rng: FWH not detected [ 0.879667] brd: module loaded [ 0.887530] loop: module loaded [ 0.888935] ahci 0000:00:1f.2: version 3.0 [ 0.888974] ahci 0000:00:1f.2: PCI->APIC IRQ transform: INT B -> IRQ 19 [ 0.889157] ahci 0000:00:1f.2: forcing PORTS_IMPL to 0xf [ 0.889359] ahci 0000:00:1f.2: AHCI 0001.0000 32 slots 4 ports 1.5 Gbps 0xf impl IDE mode [ 0.889818] ahci 0000:00:1f.2: flags: 64bit ncq pm led pmp slum part [ 0.894190] scsi host0: ahci [ 0.895209] scsi host1: ahci [ 0.896636] scsi host2: ahci [ 0.899524] scsi host3: ahci [ 0.899813] ata1: SATA max UDMA/133 abar m1024@0xfe63b800 port 0xfe63b900 irq 19 [ 0.899917] ata2: SATA max UDMA/133 abar m1024@0xfe63b800 port 0xfe63b980 irq 19 [ 0.900012] ata3: SATA max UDMA/133 abar m1024@0xfe63b800 port 0xfe63ba00 irq 19 [ 0.900106] ata4: SATA max UDMA/133 abar m1024@0xfe63b800 port 0xfe63ba80 irq 19 [ 0.900348] ata_piix 0000:00:1f.1: version 2.13 [ 0.900384] ata_piix 0000:00:1f.1: PCI->APIC IRQ transform: INT A -> IRQ 18 [ 0.901686] scsi host4: ata_piix [ 0.906225] scsi host5: ata_piix [ 0.906445] ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14 [ 0.906544] ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15 [ 0.923847] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 0.923964] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld Jason@zx2c4.com. All Rights Reserved. [ 0.924066] MACsec IEEE 802.1AE [ 0.926078] tun: Universal TUN/TAP device driver, 1.6 [ 0.933094] e100: Intel(R) PRO/100 Network Driver [ 0.933181] e100: Copyright(c) 1999-2006 Intel Corporation [ 0.933364] e100 0000:05:02.0: PCI->APIC IRQ transform: INT A -> IRQ 16 [ 0.987812] e100 0000:05:02.0 eth0: addr 0xfebff000, irq 16, MAC addr 00:04:a7:0a:03:34 [ 0.988102] e100 0000:05:03.0: PCI->APIC IRQ transform: INT A -> IRQ 17 [ 1.041393] e100 0000:05:03.0 eth1: addr 0xfebfe000, irq 17, MAC addr 00:04:a7:0a:03:35 [ 1.041687] e100 0000:05:04.0: PCI->APIC IRQ transform: INT A -> IRQ 18 [ 1.069493] ata5.01: CFA: TRANSCEND, 20080820, max UDMA/66 [ 1.069592] ata5.01: 15662304 sectors, multi 0: LBA [ 1.096351] e100 0000:05:04.0 eth2: addr 0xfebfd000, irq 18, MAC addr 00:04:a7:0a:03:36 [ 1.096652] e100 0000:05:05.0: PCI->APIC IRQ transform: INT A -> IRQ 19 [ 1.149944] e100 0000:05:05.0 eth3: addr 0xfebfc000, irq 19, MAC addr 00:04:a7:0a:03:37 [ 1.150135] e1000: Intel(R) PRO/1000 Network Driver [ 1.150203] e1000: Copyright (c) 1999-2006 Intel Corporation. [ 1.150324] e1000e: Intel(R) PRO/1000 Network Driver [ 1.150392] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 1.150562] e1000e 0000:01:00.0: PCI->APIC IRQ transform: INT A -> IRQ 16 [ 1.150776] e1000e 0000:01:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 1.212807] ata3: SATA link down (SStatus 0 SControl 300) [ 1.212943] ata1: SATA link down (SStatus 0 SControl 300) [ 1.283565] e1000e 0000:01:00.0 eth4: (PCI Express:2.5GT/s:Width x1) 00:04:a7:08:c5:b4 [ 1.283690] e1000e 0000:01:00.0 eth4: Intel(R) PRO/1000 Network Connection [ 1.283855] e1000e 0000:01:00.0 eth4: MAC: 2, PHY: 2, PBA No: FFFFFF-0FF [ 1.292947] e1000e 0000:02:00.0: PCI->APIC IRQ transform: INT A -> IRQ 17 [ 1.293182] e1000e 0000:02:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 1.416968] e1000e 0000:02:00.0 eth5: (PCI Express:2.5GT/s:Width x1) 00:04:a7:08:c5:b5 [ 1.417093] e1000e 0000:02:00.0 eth5: Intel(R) PRO/1000 Network Connection [ 1.417257] e1000e 0000:02:00.0 eth5: MAC: 2, PHY: 2, PBA No: FFFFFF-0FF [ 1.419923] e1000e 0000:03:00.0: PCI->APIC IRQ transform: INT A -> IRQ 18 [ 1.420164] e1000e 0000:03:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 1.533895] e1000e 0000:03:00.0 eth6: (PCI Express:2.5GT/s:Width x1) 00:04:a7:08:c5:b6 [ 1.534017] e1000e 0000:03:00.0 eth6: Intel(R) PRO/1000 Network Connection [ 1.534181] e1000e 0000:03:00.0 eth6: MAC: 2, PHY: 2, PBA No: FFFFFF-0FF [ 1.534366] e1000e 0000:04:00.0: PCI->APIC IRQ transform: INT A -> IRQ 19 [ 1.534606] e1000e 0000:04:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 1.619873] tsc: Refined TSC clocksource calibration: 1000.035 MHz [ 1.619977] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0xe6a38202b4, max_idle_ns: 440795212232 ns [ 1.620090] clocksource: Switched to clocksource tsc [ 1.646800] e1000e 0000:04:00.0 eth7: (PCI Express:2.5GT/s:Width x1) 00:04:a7:08:c5:b7 [ 1.646925] e1000e 0000:04:00.0 eth7: Intel(R) PRO/1000 Network Connection [ 1.647089] e1000e 0000:04:00.0 eth7: MAC: 2, PHY: 2, PBA No: FFFFFF-0FF [ 1.647261] igb: Intel(R) Gigabit Ethernet Network Driver [ 1.647331] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.647452] Intel(R) 2.5G Ethernet Linux Driver [ 1.647519] Copyright(c) 2018 Intel Corporation. [ 1.647650] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver [ 1.647722] ixgbe: Copyright (c) 1999-2016 Intel Corporation. [ 1.648340] i40e: Intel(R) Ethernet Connection XL710 Network Driver [ 1.648420] i40e: Copyright (c) 2013 - 2019 Intel Corporation. [ 1.648674] sky2: driver version 1.30 [ 1.650562] PPP generic driver version 2.4.2 [ 1.650946] PPP BSD Compression module registered [ 1.651019] PPP Deflate Compression module registered [ 1.651087] NET: Registered PF_PPPOX protocol family [ 1.651181] PPTP driver version 0.8.5 [ 1.653565] uhci_hcd 0000:00:1d.0: PCI->APIC IRQ transform: INT A -> IRQ 23 [ 1.653715] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 1.653961] ehci-pci 0000:00:1d.7: PCI->APIC IRQ transform: INT A -> IRQ 23 [ 1.654360] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 [ 1.654513] uhci_hcd 0000:00:1d.0: irq 23, io port 0x00009880 [ 1.656722] hub 1-0:1.0: USB hub found [ 1.656819] hub 1-0:1.0: 2 ports detected [ 1.657352] usbcore: registered new interface driver usb-storage [ 1.657723] i8042: PNP: No PS/2 controller found. [ 1.657791] i8042: Probing ports directly. [ 1.660618] ehci-pci 0000:00:1d.7: EHCI Host Controller [ 1.660962] ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 2 [ 1.661085] ehci-pci 0000:00:1d.7: debug port 1 [ 1.667498] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 1.667713] ehci-pci 0000:00:1d.7: irq 23, io mem 0xfe63bc00 [ 1.667944] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 1.668674] mousedev: PS/2 mouse device common for all mice [ 1.669999] rtc_cmos rtc_cmos: registered as rtc0 [ 1.670118] rtc_cmos rtc_cmos: setting system clock to 2024-04-04T12:16:11 UTC (1712232971) [ 1.670293] rtc_cmos rtc_cmos: alarms up to one day, 114 bytes nvram, hpet irqs [ 1.670453] i2c_dev: i2c /dev entries driver [ 1.671299] hid: raw HID events driver (C) Jiri Kosina [ 1.671425] usbcore: registered new interface driver usbhid [ 1.671495] usbhid: USB HID core driver [ 1.671606] GACT probability on [ 1.671688] Mirror/redirect action on [ 1.671775] Simple TC action Loaded [ 1.672307] netem: version 1.3 [ 1.672425] u32 classifier [ 1.672486] Performance counters on [ 1.672547] input device check on [ 1.672608] Actions configured [ 1.673567] i801_smbus 0000:00:1f.3: PCI->APIC IRQ transform: INT B -> IRQ 19 [ 1.673710] i801_smbus 0000:00:1f.3: SMBus using PCI interrupt [ 1.678014] xt_time: kernel timezone is -0000 [ 1.678377] ipip: IPv4 and MPLS over IPv4 tunneling driver [ 1.679858] ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 1.680485] hub 2-0:1.0: USB hub found [ 1.680580] hub 2-0:1.0: 2 ports detected [ 1.680915] hub 1-0:1.0: USB hub found [ 1.681074] gre: GRE over IPv4 demultiplexor driver [ 1.681144] ip_gre: GRE over IPv4 tunneling driver [ 1.682280] IPv4 over IPsec tunneling driver [ 1.682741] Initializing XFRM netlink socket [ 1.682831] IPsec XFRM device driver [ 1.682905] IPv6: Loaded, but administratively disabled, reboot required to enable [ 1.682999] IPv6: ah6_init: can't add xfrm type [ 1.683064] IPv6: esp6_init: can't add xfrm type [ 1.683129] IPv6: ipcomp6_init: can't add xfrm type [ 1.683212] hub 1-0:1.0: 2 ports detected [ 1.697258] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.697704] ip6_gre: GRE over IPv6 tunneling driver [ 1.698159] NET: Registered PF_PACKET protocol family [ 1.698243] NET: Registered PF_KEY protocol family [ 1.698358] Bridge firewalling registered [ 1.703300] NET: Registered PF_KCM protocol family [ 1.703536] l2tp_core: L2TP core driver, V2.0 [ 1.703612] l2tp_ppp: PPPoL2TP kernel driver, V2.0 [ 1.703678] l2tp_ip: L2TP IP encapsulation support (L2TPv3) [ 1.703761] l2tp_netlink: L2TP netlink interface [ 1.703872] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3) [ 1.703941] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3) [ 1.704223] 8021q: 802.1Q VLAN Support v1.8 [ 1.706569] microcode: Microcode Update Driver: v2.2. [ 1.739104] sched_clock: Marking stable (1726683808, 9797698)->(1738705429, -2223923) [ 1.741745] Loading compiled-in X.509 certificates [ 1.757082] Key type .fscrypt registered [ 1.757171] Key type fscrypt-provisioning registered [ 1.913171] ata2: failed to resume link (SControl 0) [ 1.913283] ata2: SATA link down (SStatus 0 SControl 0) [ 1.919834] ata4: failed to resume link (SControl 0) [ 1.919932] ata4: SATA link down (SStatus 0 SControl 0) [ 1.923910] scsi 4:0:1:0: Direct-Access ATA TRANSCEND 0820 PQ: 0 ANSI: 5 [ 1.925035] sd 4:0:1:0: [sda] 15662304 512-byte logical blocks: (8.02 GB/7.47 GiB) [ 1.925166] sd 4:0:1:0: [sda] Write Protect is off [ 1.925238] sd 4:0:1:0: [sda] Mode Sense: 00 3a 00 00 [ 1.925272] sd 4:0:1:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 1.925408] sd 4:0:1:0: [sda] Preferred minimum I/O size 512 bytes [ 1.927769] sd 4:0:1:0: Attached scsi generic sg0 type 0 [ 1.931553] sda: sda1 [ 1.932031] usb 2-1: new high-speed USB device number 2 using ehci-pci [ 1.935405] sd 4:0:1:0: [sda] Attached SCSI disk [ 2.082200] usb-storage 2-1:1.0: USB Mass Storage device detected [ 2.082722] scsi host6: usb-storage 2-1:1.0 [ 2.409883] usb 1-2: new low-speed USB device number 2 using uhci_hcd [ 2.662968] input: HID 046a:0011 as /devices/pci0000:00/0000:00:1d.0/usb1/1-2/1-2:1.0/0003:046A:0011.0001/input/input2 [ 2.716785] hid-generic 0003:046A:0011.0001: input,hidraw0: USB HID v1.11 Keyboard [HID 046a:0011] on usb-0000:00:1d.0-2/input0 [ 3.087395] scsi 6:0:0:0: Direct-Access Kingston DataTraveler 2.0 1.00 PQ: 0 ANSI: 2 [ 3.088289] sd 6:0:0:0: Attached scsi generic sg1 type 0 [ 3.089735] sd 6:0:0:0: [sdb] 2007040 512-byte logical blocks: (1.03 GB/980 MiB) [ 3.090611] sd 6:0:0:0: [sdb] Write Protect is off [ 3.090698] sd 6:0:0:0: [sdb] Mode Sense: 23 00 00 00 [ 3.091359] sd 6:0:0:0: [sdb] No Caching mode page found [ 3.091439] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 3.096137] sdb: sdb1 [ 3.096573] sd 6:0:0:0: [sdb] Attached SCSI removable disk [ 7.560378] Freeing initrd memory: 91572K [ 7.631832] Key type encrypted registered [ 7.632260] gtp: GTP module loaded (pdp ctx size 60 bytes) [ 7.632782] clk: Disabling unused clocks [ 7.633622] Freeing unused kernel image (initmem) memory: 640K [ 7.633877] Write protecting kernel text and read-only data: 15944k [ 7.633957] rodata_test: all tests were successful [ 7.634036] Run /init as init process [ 7.634098] with arguments: [ 7.634101] /init [ 7.634104] with environment: [ 7.634106] HOME=/ [ 7.634109] TERM=linux [ 7.634112] BOOT_IMAGE=kernel [ 12.186491] random: crng init done
Regards
Am 2024-04-05 11:33, schrieb Thomas Gleixner:
On Thu, Apr 04 2024 at 17:57, Greg Kroah-Hartman wrote:
On Thu, Apr 04, 2024 at 02:07:11PM +0200, Wolfgang Walter wrote:
Reverting this commit in v6.6.24 solves the problem.
Is this also an issue in 6.9-rc1 or newer or 6.8.3 or newer?
Also can you please provide the boot dmesg from a working kernel?
Thanks,
tglx
here dmesg of 6.9-rc1 (which works fine):
[ 0.000000] Linux version 6.9.0-rc1 (S-kernel@sid-i386) (gcc (Debian 13.2.0-23) 13.2.0, GNU ld (GNU Binutils for Debian) 2.42) #1 PREEMPT_DYNAMIC Fri Apr 5 12:12:01 CEST 2024 [ 0.000000] Disabled fast string operations [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable [ 0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000003fefffff] usable [ 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fed13000-0x00000000fed19fff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000ffb00000-0x00000000ffffffff] reserved [ 0.000000] Notice: NX (Execute Disable) protection cannot be enabled: non-PAE kernel! [ 0.000000] APIC: Static calls initialized [ 0.000000] SMBIOS 2.3 present. [ 0.000000] DMI: To Be Filled By O.E.M. To Be Filled By O.E.M./To be filled by O.E.M., BIOS 080012 10/16/2008 [ 0.000000] tsc: Fast TSC calibration using PIT [ 0.000000] tsc: Detected 999.965 MHz processor [ 0.011044] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved [ 0.011055] e820: remove [mem 0x000a0000-0x000fffff] usable [ 0.011070] last_pfn = 0x3ff00 max_arch_pfn = 0x100000 [ 0.011087] MTRR map: 7 entries (5 fixed + 2 variable; max 21), built from 8 variable MTRRs [ 0.011093] x86/PAT: PAT not supported by the CPU. [ 0.011099] x86/PAT: Configuration [0-7]: WB WT UC- UC WB WT UC- UC [ 0.011283] Warning only 887MB will be used. [ 0.011286] Use a HIGHMEM enabled kernel. [ 0.024443] found SMP MP-table at [mem 0x000ff780-0x000ff78f] [ 0.024462] initial memory mapped: [mem 0x00000000-0x023fffff] [ 0.024545] RAMDISK: [mem 0x3a593000-0x3fefffff] [ 0.024550] Allocated new RAMDISK: [mem 0x31e91000-0x377fdc20] [ 0.184495] Move RAMDISK from [mem 0x3a593000-0x3feffc20] to [mem 0x31e91000-0x377fdc20] [ 0.184522] ACPI: Early table checksum verification disabled [ 0.185291] ACPI BIOS Error (bug): A valid RSDP was not found (20230628/tbxfroot-222) [ 0.185316] Intel MultiProcessor Specification v1.4 [ 0.185319] Virtual Wire compatibility mode. [ 0.185324] MPTABLE: OEM ID: Intel [ 0.185328] MPTABLE: Product ID: Alviso [ 0.185330] MPTABLE: APIC at: 0xFEE00000 [ 0.185338] 887MB LOWMEM available. [ 0.185341] mapped low ram: 0 - 377fe000 [ 0.185344] low ram: 0 - 377fe000 [ 0.185351] Zone ranges: [ 0.185353] DMA [mem 0x0000000000001000-0x0000000000ffffff] [ 0.185361] Normal [mem 0x0000000001000000-0x00000000377fdfff] [ 0.185367] Movable zone start for each node [ 0.185369] Early memory node ranges [ 0.185371] node 0: [mem 0x0000000000001000-0x000000000009efff] [ 0.185376] node 0: [mem 0x0000000000100000-0x000000003fefffff] [ 0.185382] Initmem setup node 0 [mem 0x0000000000001000-0x000000003fefffff] [ 0.185411] On node 0, zone DMA: 1 pages in unavailable ranges [ 0.185693] On node 0, zone DMA: 97 pages in unavailable ranges [ 0.201157] On node 0, zone Normal: 2 pages in unavailable ranges [ 0.201181] Reserving Intel graphics memory at [mem 0x3ff00000-0x3fffffff] [ 0.201466] Intel MultiProcessor Specification v1.4 [ 0.201472] Virtual Wire compatibility mode. [ 0.201477] MPTABLE: OEM ID: Intel [ 0.201480] MPTABLE: Product ID: Alviso [ 0.201482] MPTABLE: APIC at: 0xFEE00000 [ 0.201488] Processor #0 (Bootup-CPU) [ 0.201504] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23 [ 0.201517] Processors: 1 [ 0.201521] CPU topo: Max. logical packages: 1 [ 0.201524] CPU topo: Max. logical dies: 1 [ 0.201527] CPU topo: Max. dies per package: 1 [ 0.201529] CPU topo: Max. threads per core: 1 [ 0.201535] CPU topo: Num. cores per package: 1 [ 0.201538] CPU topo: Num. threads per package: 1 [ 0.201540] CPU topo: Allowing 1 present CPUs plus 0 hotplug CPUs [ 0.201570] [mem 0x40000000-0xdfffffff] available for PCI devices [ 0.201581] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370452778343963 ns [ 0.201658] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.201673] pcpu-alloc: [0] 0 [ 0.201697] Kernel command line: BOOT_IMAGE=kernel initrd=system.gz init=/sbin/init ipv6.disable=1 dummy.numdummies=16 ide-core.nodma=1.0 iommu=pt libata.dma=3 random.trust_cpu=on reboot=cold,force retbleed=off [ 0.202541] Unknown kernel command line parameters "BOOT_IMAGE=kernel", will be passed to user space. [ 0.203023] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.203310] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.203384] Built 1 zonelists, mobility grouping on. Total pages: 225008 [ 0.203394] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.219384] Checking if this processor honours the WP bit even in supervisor mode...Ok. [ 0.219411] Memory: 789208K/908912K available (12921K kernel code, 739K rwdata, 3076K rodata, 632K init, 280K bss, 119704K reserved, 0K cma-reserved) [ 0.265600] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.266886] Dynamic Preempt: full [ 0.267261] rcu: Preemptible hierarchical RCU implementation. [ 0.267267] Trampoline variant of Tasks RCU enabled. [ 0.267270] Tracing variant of Tasks RCU enabled. [ 0.267272] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies. [ 0.267287] RCU Tasks: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1. [ 0.267295] RCU Tasks Trace: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1. [ 0.267304] NR_IRQS: 2304, nr_irqs: 48, preallocated irqs: 16 [ 0.267620] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.272009] Console: colour VGA+ 80x25 [ 0.272020] printk: legacy console [tty0] enabled [ 0.278176] APIC: Switch to symmetric I/O mode setup [ 0.278312] ExtINT not setup in hardware but reported by MP table [ 0.278804] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=0 pin2=0 [ 0.294846] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x1cd3ebf4f53, max_idle_ns: 881590451058 ns [ 0.294970] Calibrating delay loop (skipped), value calculated using timer frequency.. 2000.26 BogoMIPS (lpj=3333216) [ 0.295096] Disabled fast string operations [ 0.295183] CPU0: Thermal monitoring enabled (TM1) [ 0.295295] Last level iTLB entries: 4KB 128, 2MB 0, 4MB 2 [ 0.295368] Last level dTLB entries: 4KB 128, 2MB 0, 4MB 8, 1GB 0 [ 0.295445] CPU: Intel(R) Celeron(R) M processor 1.00GHz (family: 0x6, model: 0xd, stepping: 0x8) [ 0.295554] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization [ 0.295655] Spectre V2 : Mitigation: Retpolines [ 0.295720] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch [ 0.295815] Spectre V2 : Spectre v2 / SpectreRSB : Filling RSB on VMEXIT [ 0.295905] Speculative Store Bypass: Vulnerable [ 0.295972] L1TF: Kernel not compiled for PAE. No mitigation for L1TF [ 0.296043] MDS: Vulnerable: Clear CPU buffers attempted, no microcode [ 0.296133] MMIO Stale Data: Unknown: No mitigations [ 0.296201] x86/fpu: x87 FPU will use FXSAVE [ 0.297526] pid_max: default: 32768 minimum: 301 [ 0.304402] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.304509] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.310412] Performance Events: p6 PMU driver. [ 0.310502] ... version: 0 [ 0.310565] ... bit width: 32 [ 0.310628] ... generic registers: 2 [ 0.310691] ... value mask: 00000000ffffffff [ 0.310758] ... max period: 000000007fffffff [ 0.310825] ... fixed-purpose events: 0 [ 0.310887] ... event mask: 0000000000000003 [ 0.311099] signal: max sigframe size: 1440 [ 0.311261] rcu: Hierarchical SRCU implementation. [ 0.311332] rcu: Max phase no-delay instances is 1000. [ 0.524958] devtmpfs: initialized [ 0.524958] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns [ 0.524958] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.529440] pinctrl core: initialized pinctrl subsystem [ 0.530684] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.531926] thermal_sys: Registered thermal governor 'fair_share' [ 0.531934] thermal_sys: Registered thermal governor 'bang_bang' [ 0.532010] thermal_sys: Registered thermal governor 'step_wise' [ 0.532079] thermal_sys: Registered thermal governor 'user_space' [ 0.532186] cpuidle: using governor ladder [ 0.534781] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=5 [ 0.534861] PCI: Using configuration type 1 for base access [ 0.537177] cryptd: max_cpu_qlen set to 1000 [ 0.540234] ACPI: Interpreter disabled. [ 0.540350] iommu: Default domain type: Passthrough (set via kernel command line) [ 0.540820] SCSI subsystem initialized [ 0.540994] libata version 3.00 loaded. [ 0.541138] usbcore: registered new interface driver usbfs [ 0.541227] usbcore: registered new interface driver hub [ 0.541314] usbcore: registered new device driver usb [ 0.541510] pps_core: LinuxPPS API ver. 1 registered [ 0.541578] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti giometti@linux.it [ 0.541639] PTP clock support registered [ 0.541731] EDAC MC: Ver: 3.0.0 [ 0.545937] PCI: Probing PCI hardware [ 0.546008] PCI: root bus 00: using default resources [ 0.546014] PCI: Probing PCI hardware (bus 00) [ 0.546064] PCI host bridge to bus 0000:00 [ 0.546131] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 0.546207] pci_bus 0000:00: root bus resource [mem 0x00000000-0xffffffff] [ 0.546302] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.546422] pci 0000:00:00.0: [8086:2590] type 00 class 0x060000 conventional PCI endpoint [ 0.546673] pci 0000:00:02.0: [8086:2592] type 00 class 0x030000 conventional PCI endpoint [ 0.546786] pci 0000:00:02.0: BAR 0 [mem 0xfe680000-0xfe6fffff] [ 0.546863] pci 0000:00:02.0: BAR 1 [io 0x9c00-0x9c07] [ 0.546940] pci 0000:00:02.0: BAR 2 [mem 0xd0000000-0xdfffffff pref] [ 0.547017] pci 0000:00:02.0: BAR 3 [mem 0xfe640000-0xfe67ffff] [ 0.547111] pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff] [ 0.547335] pci 0000:00:02.1: [8086:2792] type 00 class 0x038000 conventional PCI endpoint [ 0.547447] pci 0000:00:02.1: BAR 0 [mem 0xfe580000-0xfe5fffff] [ 0.547702] pci 0000:00:1c.0: [8086:2660] type 01 class 0x060400 PCIe Root Port [ 0.548341] pci 0000:00:1c.0: PCI bridge to [bus 01] [ 0.548416] pci 0000:00:1c.0: bridge window [io 0xa000-0xafff] [ 0.548490] pci 0000:00:1c.0: bridge window [mem 0xfe700000-0xfe7fffff] [ 0.548605] pci 0000:00:1c.0: enabling Extended Tags [ 0.548717] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold [ 0.548934] pci 0000:00:1c.1: [8086:2662] type 01 class 0x060400 PCIe Root Port [ 0.549064] pci 0000:00:1c.1: PCI bridge to [bus 02] [ 0.549136] pci 0000:00:1c.1: bridge window [io 0xb000-0xbfff] [ 0.549209] pci 0000:00:1c.1: bridge window [mem 0xfe800000-0xfe8fffff] [ 0.549322] pci 0000:00:1c.1: enabling Extended Tags [ 0.549433] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold [ 0.549611] pci 0000:00:1c.2: [8086:2664] type 01 class 0x060400 PCIe Root Port [ 0.549740] pci 0000:00:1c.2: PCI bridge to [bus 03] [ 0.549812] pci 0000:00:1c.2: bridge window [io 0xc000-0xcfff] [ 0.549885] pci 0000:00:1c.2: bridge window [mem 0xfe900000-0xfe9fffff] [ 0.549998] pci 0000:00:1c.2: enabling Extended Tags [ 0.550109] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold [ 0.550305] pci 0000:00:1c.3: [8086:2666] type 01 class 0x060400 PCIe Root Port [ 0.550434] pci 0000:00:1c.3: PCI bridge to [bus 04] [ 0.550506] pci 0000:00:1c.3: bridge window [io 0xd000-0xdfff] [ 0.550579] pci 0000:00:1c.3: bridge window [mem 0xfea00000-0xfeafffff] [ 0.550692] pci 0000:00:1c.3: enabling Extended Tags [ 0.550801] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold [ 0.550997] pci 0000:00:1d.0: [8086:2658] type 00 class 0x0c0300 conventional PCI endpoint [ 0.551147] pci 0000:00:1d.0: BAR 4 [io 0x9880-0x989f] [ 0.551336] pci 0000:00:1d.7: [8086:265c] type 00 class 0x0c0320 conventional PCI endpoint [ 0.551454] pci 0000:00:1d.7: BAR 0 [mem 0xfe63bc00-0xfe63bfff] [ 0.551697] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold [ 0.551883] pci 0000:00:1e.0: [8086:2448] type 01 class 0x060401 conventional PCI bridge [ 0.552013] pci 0000:00:1e.0: PCI bridge to [bus 05] (subtractive decode) [ 0.552110] pci 0000:00:1e.0: bridge window [io 0xe000-0xefff] [ 0.552183] pci 0000:00:1e.0: bridge window [mem 0xfeb00000-0xfebfffff] [ 0.552415] pci 0000:00:1f.0: [8086:2641] type 00 class 0x060100 conventional PCI endpoint [ 0.552610] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000 [ 0.552625] pci 0000:00:1f.0: quirk: [io 0x0800-0x087f] claimed by ICH6 ACPI/GPIO/TCO [ 0.552726] pci 0000:00:1f.0: quirk: [io 0x0480-0x04bf] claimed by ICH6 GPIO [ 0.552823] pci 0000:00:1f.0: LPC Generic IO decode 2 PIO at 0a00-0a0f [ 0.553007] pci 0000:00:1f.1: [8086:266f] type 00 class 0x01018a conventional PCI endpoint [ 0.553125] pci 0000:00:1f.1: BAR 0 [io 0x0000-0x0007] [ 0.553203] pci 0000:00:1f.1: BAR 1 [io 0x0000-0x0003] [ 0.553279] pci 0000:00:1f.1: BAR 2 [io 0x0000-0x0007] [ 0.553356] pci 0000:00:1f.1: BAR 3 [io 0x0000-0x0003] [ 0.553434] pci 0000:00:1f.1: BAR 4 [io 0xffa0-0xffaf] [ 0.553522] pci 0000:00:1f.1: BAR 0 [io 0x01f0-0x01f7]: legacy IDE quirk [ 0.553616] pci 0000:00:1f.1: BAR 1 [io 0x03f6]: legacy IDE quirk [ 0.553687] pci 0000:00:1f.1: BAR 2 [io 0x0170-0x0177]: legacy IDE quirk [ 0.553781] pci 0000:00:1f.1: BAR 3 [io 0x0376]: legacy IDE quirk [ 0.553976] pci 0000:00:1f.2: [8086:2653] type 00 class 0x01018f conventional PCI endpoint [ 0.554093] pci 0000:00:1f.2: BAR 0 [io 0x9800-0x9807] [ 0.554170] pci 0000:00:1f.2: BAR 1 [io 0x9480-0x9483] [ 0.554247] pci 0000:00:1f.2: BAR 2 [io 0x9400-0x9407] [ 0.554323] pci 0000:00:1f.2: BAR 3 [io 0x9080-0x9083] [ 0.554398] pci 0000:00:1f.2: BAR 4 [io 0x9000-0x900f] [ 0.554474] pci 0000:00:1f.2: BAR 5 [mem 0xfe63b800-0xfe63bbff] [ 0.554579] pci 0000:00:1f.2: PME# supported from D3hot [ 0.554737] pci 0000:00:1f.3: [8086:266a] type 00 class 0x0c0500 conventional PCI endpoint [ 0.554899] pci 0000:00:1f.3: BAR 4 [io 0x0400-0x041f] [ 0.555197] pci 0000:01:00.0: [8086:109a] type 00 class 0x020000 PCIe Endpoint [ 0.555331] pci 0000:01:00.0: BAR 0 [mem 0xfe7e0000-0xfe7fffff] [ 0.555437] pci 0000:01:00.0: BAR 2 [io 0xac00-0xac1f] [ 0.555658] pci 0000:01:00.0: PME# supported from D0 D3hot [ 0.555865] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' [ 0.555997] pci 0000:00:1c.0: PCI bridge to [bus 01] [ 0.556183] pci 0000:02:00.0: [8086:109a] type 00 class 0x020000 PCIe Endpoint [ 0.556314] pci 0000:02:00.0: BAR 0 [mem 0xfe8e0000-0xfe8fffff] [ 0.556419] pci 0000:02:00.0: BAR 2 [io 0xbc00-0xbc1f] [ 0.556640] pci 0000:02:00.0: PME# supported from D0 D3hot [ 0.556844] pci 0000:02:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' [ 0.556971] pci 0000:00:1c.1: PCI bridge to [bus 02] [ 0.557136] pci 0000:03:00.0: [8086:109a] type 00 class 0x020000 PCIe Endpoint [ 0.557267] pci 0000:03:00.0: BAR 0 [mem 0xfe9e0000-0xfe9fffff] [ 0.557372] pci 0000:03:00.0: BAR 2 [io 0xcc00-0xcc1f] [ 0.557593] pci 0000:03:00.0: PME# supported from D0 D3hot [ 0.557792] pci 0000:03:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' [ 0.557920] pci 0000:00:1c.2: PCI bridge to [bus 03] [ 0.558085] pci 0000:04:00.0: [8086:109a] type 00 class 0x020000 PCIe Endpoint [ 0.558214] pci 0000:04:00.0: BAR 0 [mem 0xfeae0000-0xfeafffff] [ 0.558329] pci 0000:04:00.0: BAR 2 [io 0xdc00-0xdc1f] [ 0.558553] pci 0000:04:00.0: PME# supported from D0 D3hot [ 0.558759] pci 0000:04:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' [ 0.558888] pci 0000:00:1c.3: PCI bridge to [bus 04] [ 0.558987] pci_bus 0000:05: extended config space not accessible [ 0.559104] pci 0000:05:02.0: [8086:1229] type 00 class 0x020000 conventional PCI endpoint [ 0.559223] pci 0000:05:02.0: BAR 0 [mem 0xfebff000-0xfebfffff] [ 0.559304] pci 0000:05:02.0: BAR 1 [io 0xec00-0xec3f] [ 0.559381] pci 0000:05:02.0: BAR 2 [mem 0xfebc0000-0xfebdffff] [ 0.559487] pci 0000:05:02.0: ROM [mem 0xfebe0000-0xfebeffff pref] [ 0.559590] pci 0000:05:02.0: supports D1 D2 [ 0.559656] pci 0000:05:02.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.559882] pci 0000:05:03.0: [8086:1229] type 00 class 0x020000 conventional PCI endpoint [ 0.560002] pci 0000:05:03.0: BAR 0 [mem 0xfebfe000-0xfebfefff] [ 0.560084] pci 0000:05:03.0: BAR 1 [io 0xe880-0xe8bf] [ 0.560162] pci 0000:05:03.0: BAR 2 [mem 0xfeba0000-0xfebbffff] [ 0.560267] pci 0000:05:03.0: ROM [mem 0xfeb90000-0xfeb9ffff pref] [ 0.560370] pci 0000:05:03.0: supports D1 D2 [ 0.560436] pci 0000:05:03.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.560642] pci 0000:05:04.0: [8086:1229] type 00 class 0x020000 conventional PCI endpoint [ 0.560761] pci 0000:05:04.0: BAR 0 [mem 0xfebfd000-0xfebfdfff] [ 0.560842] pci 0000:05:04.0: BAR 1 [io 0xe800-0xe83f] [ 0.560920] pci 0000:05:04.0: BAR 2 [mem 0xfeb60000-0xfeb7ffff] [ 0.561025] pci 0000:05:04.0: ROM [mem 0xfeb80000-0xfeb8ffff pref] [ 0.561130] pci 0000:05:04.0: supports D1 D2 [ 0.561195] pci 0000:05:04.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.561404] pci 0000:05:05.0: [8086:1229] type 00 class 0x020000 conventional PCI endpoint [ 0.561524] pci 0000:05:05.0: BAR 0 [mem 0xfebfc000-0xfebfcfff] [ 0.561632] pci 0000:05:05.0: BAR 1 [io 0xe480-0xe4bf] [ 0.561711] pci 0000:05:05.0: BAR 2 [mem 0xfeb40000-0xfeb5ffff] [ 0.561817] pci 0000:05:05.0: ROM [mem 0xfeb30000-0xfeb3ffff pref] [ 0.561920] pci 0000:05:05.0: supports D1 D2 [ 0.561985] pci 0000:05:05.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.562216] pci 0000:00:1e.0: PCI bridge to [bus 05] (subtractive decode) [ 0.562322] pci 0000:00:1e.0: bridge window [io 0x0000-0xffff] (subtractive decode) [ 0.562421] pci 0000:00:1e.0: bridge window [mem 0x00000000-0xffffffff] (subtractive decode) [ 0.562549] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 05 [ 0.562710] pci 0000:00:1f.0: PIIX/ICH IRQ router [8086:2641] [ 0.562792] PCI: pci_cache_line_size set to 64 bytes [ 0.562880] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff] [ 0.562888] e820: reserve RAM buffer [mem 0x3ff00000-0x3fffffff] [ 0.563020] pci 0000:00:02.0: vgaarb: setting as boot VGA device [ 0.563097] pci 0000:00:02.0: vgaarb: bridge control possible [ 0.563166] pci 0000:00:02.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none [ 0.564971] vgaarb: loaded [ 0.565627] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484882848 ns [ 0.565743] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 [ 0.565821] hpet0: 3 comparators, 64-bit 14.318180 MHz counter [ 0.569359] clocksource: Switched to clocksource tsc-early [ 0.573946] VFS: Disk quotas dquot_6.6.0 [ 0.574257] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.574450] pnp: PnP ACPI: disabled [ 0.580471] NET: Registered PF_INET protocol family [ 0.580783] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.582635] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.582758] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.582859] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.583006] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.583210] TCP: Hash tables configured (established 8192 bind 8192) [ 0.583373] UDP hash table entries: 512 (order: 1, 8192 bytes, linear) [ 0.583688] UDP-Lite hash table entries: 512 (order: 1, 8192 bytes, linear) [ 0.584231] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.584346] NET: Registered PF_XDP protocol family [ 0.584437] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 01] add_size 200000 add_align 100000 [ 0.584557] pci 0000:00:1c.1: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 02] add_size 200000 add_align 100000 [ 0.584670] pci 0000:00:1c.2: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 03] add_size 200000 add_align 100000 [ 0.584781] pci 0000:00:1c.3: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 04] add_size 200000 add_align 100000 [ 0.584916] pci 0000:00:1c.0: bridge window [mem 0x40000000-0x401fffff 64bit pref]: assigned [ 0.585019] pci 0000:00:1c.1: bridge window [mem 0x40200000-0x403fffff 64bit pref]: assigned [ 0.585119] pci 0000:00:1c.2: bridge window [mem 0x40400000-0x405fffff 64bit pref]: assigned [ 0.585220] pci 0000:00:1c.3: bridge window [mem 0x40600000-0x407fffff 64bit pref]: assigned [ 0.585325] pci 0000:00:1c.0: PCI bridge to [bus 01] [ 0.585396] pci 0000:00:1c.0: bridge window [io 0xa000-0xafff] [ 0.585472] pci 0000:00:1c.0: bridge window [mem 0xfe700000-0xfe7fffff] [ 0.585568] pci 0000:00:1c.0: bridge window [mem 0x40000000-0x401fffff 64bit pref] [ 0.585670] pci 0000:00:1c.1: PCI bridge to [bus 02] [ 0.585739] pci 0000:00:1c.1: bridge window [io 0xb000-0xbfff] [ 0.585814] pci 0000:00:1c.1: bridge window [mem 0xfe800000-0xfe8fffff] [ 0.585909] pci 0000:00:1c.1: bridge window [mem 0x40200000-0x403fffff 64bit pref] [ 0.586011] pci 0000:00:1c.2: PCI bridge to [bus 03] [ 0.586079] pci 0000:00:1c.2: bridge window [io 0xc000-0xcfff] [ 0.586154] pci 0000:00:1c.2: bridge window [mem 0xfe900000-0xfe9fffff] [ 0.586250] pci 0000:00:1c.2: bridge window [mem 0x40400000-0x405fffff 64bit pref] [ 0.586352] pci 0000:00:1c.3: PCI bridge to [bus 04] [ 0.586420] pci 0000:00:1c.3: bridge window [io 0xd000-0xdfff] [ 0.586495] pci 0000:00:1c.3: bridge window [mem 0xfea00000-0xfeafffff] [ 0.587304] pci 0000:00:1c.3: bridge window [mem 0x40600000-0x407fffff 64bit pref] [ 0.587410] pci 0000:00:1e.0: PCI bridge to [bus 05] [ 0.587479] pci 0000:00:1e.0: bridge window [io 0xe000-0xefff] [ 0.587556] pci 0000:00:1e.0: bridge window [mem 0xfeb00000-0xfebfffff] [ 0.587658] pci_bus 0000:00: resource 4 [io 0x0000-0xffff] [ 0.587729] pci_bus 0000:00: resource 5 [mem 0x00000000-0xffffffff] [ 0.587804] pci_bus 0000:01: resource 0 [io 0xa000-0xafff] [ 0.587874] pci_bus 0000:01: resource 1 [mem 0xfe700000-0xfe7fffff] [ 0.587946] pci_bus 0000:01: resource 2 [mem 0x40000000-0x401fffff 64bit pref] [ 0.588042] pci_bus 0000:02: resource 0 [io 0xb000-0xbfff] [ 0.588111] pci_bus 0000:02: resource 1 [mem 0xfe800000-0xfe8fffff] [ 0.588184] pci_bus 0000:02: resource 2 [mem 0x40200000-0x403fffff 64bit pref] [ 0.588279] pci_bus 0000:03: resource 0 [io 0xc000-0xcfff] [ 0.588349] pci_bus 0000:03: resource 1 [mem 0xfe900000-0xfe9fffff] [ 0.588422] pci_bus 0000:03: resource 2 [mem 0x40400000-0x405fffff 64bit pref] [ 0.588518] pci_bus 0000:04: resource 0 [io 0xd000-0xdfff] [ 0.588588] pci_bus 0000:04: resource 1 [mem 0xfea00000-0xfeafffff] [ 0.588660] pci_bus 0000:04: resource 2 [mem 0x40600000-0x407fffff 64bit pref] [ 0.588757] pci_bus 0000:05: resource 0 [io 0xe000-0xefff] [ 0.588827] pci_bus 0000:05: resource 1 [mem 0xfeb00000-0xfebfffff] [ 0.588899] pci_bus 0000:05: resource 4 [io 0x0000-0xffff] [ 0.588969] pci_bus 0000:05: resource 5 [mem 0x00000000-0xffffffff] [ 0.589113] pci 0000:00:1d.0: PCI->APIC IRQ transform: INT A -> IRQ 23 [ 0.589241] pci 0000:00:1d.7: PCI->APIC IRQ transform: INT A -> IRQ 23 [ 0.616749] pci 0000:00:1d.7: quirk_usb_early_handoff+0x0/0x7b4 took 26869 usecs [ 0.616930] pci 0000:05:02.0: Firmware left e100 interrupts enabled; disabling [ 0.617039] pci 0000:05:03.0: Firmware left e100 interrupts enabled; disabling [ 0.617148] pci 0000:05:04.0: Firmware left e100 interrupts enabled; disabling [ 0.617255] pci 0000:05:05.0: Firmware left e100 interrupts enabled; disabling [ 0.617353] PCI: CLS 64 bytes, default 64 [ 0.618461] Trying to unpack rootfs image as initramfs... [ 0.620263] platform rtc_cmos: registered platform RTC device (no PNP device found) [ 0.620698] PCLMULQDQ-NI instructions are not detected. [ 0.621945] Initialise system trusted keyrings [ 0.622052] Key type blacklist registered [ 0.626783] workingset: timestamp_bits=14 max_order=18 bucket_order=4 [ 0.626892] zbud: loaded [ 0.897703] NET: Registered PF_ALG protocol family [ 0.897818] Key type asymmetric registered [ 0.897884] Asymmetric key parser 'x509' registered [ 0.897950] Asymmetric key parser 'pkcs8' registered [ 0.900111] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250) [ 0.900222] io scheduler mq-deadline registered [ 0.900288] io scheduler kyber registered [ 0.900583] io scheduler bfq registered [ 0.901244] xz_dec_test: module loaded [ 0.901313] xz_dec_test: Create a device node with 'mknod xz_dec_test c 249 0' and write .xz files to it. [ 0.901625] pcieport 0000:00:1c.0: PCI->APIC IRQ transform: INT A -> IRQ 16 [ 0.903581] pcieport 0000:00:1c.1: PCI->APIC IRQ transform: INT B -> IRQ 17 [ 0.903836] pcieport 0000:00:1c.2: PCI->APIC IRQ transform: INT C -> IRQ 18 [ 0.904089] pcieport 0000:00:1c.3: PCI->APIC IRQ transform: INT D -> IRQ 19 [ 0.905756] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.950115] serial8250: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A [ 0.954043] intel_rng: FWH not detected [ 0.970344] brd: module loaded [ 0.977815] loop: module loaded [ 0.980350] ahci 0000:00:1f.2: version 3.0 [ 0.980390] ahci 0000:00:1f.2: PCI->APIC IRQ transform: INT B -> IRQ 19 [ 0.980570] ahci 0000:00:1f.2: forcing PORTS_IMPL to 0xf [ 0.980764] ahci 0000:00:1f.2: AHCI vers 0001.0000, 32 command slots, 1.5 Gbps, IDE mode [ 0.980868] ahci 0000:00:1f.2: 4/4 ports implemented (port mask 0xf) [ 0.980940] ahci 0000:00:1f.2: flags: 64bit ncq pm led pmp slum part [ 0.987006] scsi host0: ahci [ 0.987923] scsi host1: ahci [ 0.988543] scsi host2: ahci [ 0.989193] scsi host3: ahci [ 0.989433] ata1: SATA max UDMA/133 abar m1024@0xfe63b800 port 0xfe63b900 irq 19 lpm-pol 0 [ 0.989540] ata2: SATA max UDMA/133 abar m1024@0xfe63b800 port 0xfe63b980 irq 19 lpm-pol 0 [ 0.989638] ata3: SATA max UDMA/133 abar m1024@0xfe63b800 port 0xfe63ba00 irq 19 lpm-pol 0 [ 0.989735] ata4: SATA max UDMA/133 abar m1024@0xfe63b800 port 0xfe63ba80 irq 19 lpm-pol 0 [ 0.990000] ata_piix 0000:00:1f.1: version 2.13 [ 0.990038] ata_piix 0000:00:1f.1: PCI->APIC IRQ transform: INT A -> IRQ 18 [ 0.994410] scsi host4: ata_piix [ 0.995439] scsi host5: ata_piix [ 0.995634] ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14 lpm-pol 0 [ 0.995734] ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15 lpm-pol 0 [ 1.009487] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 1.009604] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld Jason@zx2c4.com. All Rights Reserved. [ 1.009711] MACsec IEEE 802.1AE [ 1.018561] tun: Universal TUN/TAP device driver, 1.6 [ 1.026915] e100: Intel(R) PRO/100 Network Driver [ 1.027002] e100: Copyright(c) 1999-2006 Intel Corporation [ 1.027169] e100 0000:05:02.0: PCI->APIC IRQ transform: INT A -> IRQ 16 [ 1.087030] e100 0000:05:02.0 eth0: addr 0xfebff000, irq 16, MAC addr 00:04:a7:0a:03:34 [ 1.087256] e100 0000:05:03.0: PCI->APIC IRQ transform: INT A -> IRQ 17 [ 1.140370] e100 0000:05:03.0 eth1: addr 0xfebfe000, irq 17, MAC addr 00:04:a7:0a:03:35 [ 1.140588] e100 0000:05:04.0: PCI->APIC IRQ transform: INT A -> IRQ 18 [ 1.160414] ata5.01: CFA: TRANSCEND, 20080820, max UDMA/66 [ 1.160513] ata5.01: 15662304 sectors, multi 0: LBA [ 1.194258] e100 0000:05:04.0 eth2: addr 0xfebfd000, irq 18, MAC addr 00:04:a7:0a:03:36 [ 1.194481] e100 0000:05:05.0: PCI->APIC IRQ transform: INT A -> IRQ 19 [ 1.247364] e100 0000:05:05.0 eth3: addr 0xfebfc000, irq 19, MAC addr 00:04:a7:0a:03:37 [ 1.247569] e1000: Intel(R) PRO/1000 Network Driver [ 1.247640] e1000: Copyright (c) 1999-2006 Intel Corporation. [ 1.247767] e1000e: Intel(R) PRO/1000 Network Driver [ 1.247834] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 1.247979] e1000e 0000:01:00.0: PCI->APIC IRQ transform: INT A -> IRQ 16 [ 1.248202] e1000e 0000:01:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 1.306756] ata3: SATA link down (SStatus 0 SControl 300) [ 1.306886] ata1: SATA link down (SStatus 0 SControl 300) [ 1.354230] e1000e 0000:01:00.0 eth4: (PCI Express:2.5GT/s:Width x1) 00:04:a7:08:c5:b4 [ 1.354353] e1000e 0000:01:00.0 eth4: Intel(R) PRO/1000 Network Connection [ 1.354517] e1000e 0000:01:00.0 eth4: MAC: 2, PHY: 2, PBA No: FFFFFF-0FF [ 1.354702] e1000e 0000:02:00.0: PCI->APIC IRQ transform: INT A -> IRQ 17 [ 1.354926] e1000e 0000:02:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 1.467667] e1000e 0000:02:00.0 eth5: (PCI Express:2.5GT/s:Width x1) 00:04:a7:08:c5:b5 [ 1.467790] e1000e 0000:02:00.0 eth5: Intel(R) PRO/1000 Network Connection [ 1.467954] e1000e 0000:02:00.0 eth5: MAC: 2, PHY: 2, PBA No: FFFFFF-0FF [ 1.468138] e1000e 0000:03:00.0: PCI->APIC IRQ transform: INT A -> IRQ 18 [ 1.468366] e1000e 0000:03:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 1.581384] e1000e 0000:03:00.0 eth6: (PCI Express:2.5GT/s:Width x1) 00:04:a7:08:c5:b6 [ 1.581511] e1000e 0000:03:00.0 eth6: Intel(R) PRO/1000 Network Connection [ 1.581676] e1000e 0000:03:00.0 eth6: MAC: 2, PHY: 2, PBA No: FFFFFF-0FF [ 1.581861] e1000e 0000:04:00.0: PCI->APIC IRQ transform: INT A -> IRQ 19 [ 1.582109] e1000e 0000:04:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 1.614020] tsc: Refined TSC clocksource calibration: 1000.035 MHz [ 1.614127] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0xe6a38202b4, max_idle_ns: 440795212232 ns [ 1.614239] clocksource: Switched to clocksource tsc [ 1.694304] e1000e 0000:04:00.0 eth7: (PCI Express:2.5GT/s:Width x1) 00:04:a7:08:c5:b7 [ 1.694426] e1000e 0000:04:00.0 eth7: Intel(R) PRO/1000 Network Connection [ 1.694590] e1000e 0000:04:00.0 eth7: MAC: 2, PHY: 2, PBA No: FFFFFF-0FF [ 1.694787] igb: Intel(R) Gigabit Ethernet Network Driver [ 1.694859] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.694974] Intel(R) 2.5G Ethernet Linux Driver [ 1.695039] Copyright(c) 2018 Intel Corporation. [ 1.695135] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver [ 1.695207] ixgbe: Copyright (c) 1999-2016 Intel Corporation. [ 1.695741] i40e: Intel(R) Ethernet Connection XL710 Network Driver [ 1.695823] i40e: Copyright (c) 2013 - 2019 Intel Corporation. [ 1.696061] sky2: driver version 1.30 [ 1.697546] PPP generic driver version 2.4.2 [ 1.698168] PPP BSD Compression module registered [ 1.698242] PPP Deflate Compression module registered [ 1.698310] NET: Registered PF_PPPOX protocol family [ 1.698404] PPTP driver version 0.8.5 [ 1.701079] uhci_hcd 0000:00:1d.0: PCI->APIC IRQ transform: INT A -> IRQ 23 [ 1.701232] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 1.701471] ehci-pci 0000:00:1d.7: PCI->APIC IRQ transform: INT A -> IRQ 23 [ 1.701899] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 [ 1.702052] uhci_hcd 0000:00:1d.0: irq 23, io port 0x00009880 [ 1.702763] hub 1-0:1.0: USB hub found [ 1.702854] hub 1-0:1.0: 2 ports detected [ 1.704774] ehci-pci 0000:00:1d.7: EHCI Host Controller [ 1.705229] ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 2 [ 1.705364] ehci-pci 0000:00:1d.7: debug port 1 [ 1.707473] usbcore: registered new interface driver usb-storage [ 1.707825] i8042: PNP: No PS/2 controller found. [ 1.707892] i8042: Probing ports directly. [ 1.714921] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 1.715063] ehci-pci 0000:00:1d.7: irq 23, io mem 0xfe63bc00 [ 1.715235] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 1.716149] mousedev: PS/2 mouse device common for all mice [ 1.716867] rtc_cmos rtc_cmos: registered as rtc0 [ 1.716984] rtc_cmos rtc_cmos: setting system clock to 2024-04-05T10:44:26 UTC (1712313866) [ 1.717205] rtc_cmos rtc_cmos: alarms up to one day, 114 bytes nvram, hpet irqs [ 1.717660] i2c_dev: i2c /dev entries driver [ 1.721521] hid: raw HID events driver (C) Jiri Kosina [ 1.721671] usbcore: registered new interface driver usbhid [ 1.721743] usbhid: USB HID core driver [ 1.721866] GACT probability on [ 1.721949] Mirror/redirect action on [ 1.722028] Simple TC action Loaded [ 1.722531] netem: version 1.3 [ 1.722642] u32 classifier [ 1.722702] Performance counters on [ 1.722763] input device check on [ 1.722824] Actions configured [ 1.723515] xt_time: kernel timezone is -0000 [ 1.723842] ipip: IPv4 and MPLS over IPv4 tunneling driver [ 1.724217] i801_smbus 0000:00:1f.3: PCI->APIC IRQ transform: INT B -> IRQ 19 [ 1.724357] i801_smbus 0000:00:1f.3: SMBus using PCI interrupt [ 1.727386] ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 1.728080] hub 2-0:1.0: USB hub found [ 1.728222] hub 2-0:1.0: 2 ports detected [ 1.728804] hub 1-0:1.0: USB hub found [ 1.729288] gre: GRE over IPv4 demultiplexor driver [ 1.729363] ip_gre: GRE over IPv4 tunneling driver [ 1.729757] hub 1-0:1.0: 2 ports detected [ 1.735716] IPv4 over IPsec tunneling driver [ 1.736224] Initializing XFRM netlink socket [ 1.736314] IPsec XFRM device driver [ 1.736388] IPv6: Loaded, but administratively disabled, reboot required to enable [ 1.736484] IPv6: ah6_init: can't add xfrm type [ 1.737442] IPv6: esp6_init: can't add xfrm type [ 1.737509] IPv6: ipcomp6_init: can't add xfrm type [ 1.745348] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.745755] ip6_gre: GRE over IPv6 tunneling driver [ 1.746196] NET: Registered PF_PACKET protocol family [ 1.746278] NET: Registered PF_KEY protocol family [ 1.746391] Bridge firewalling registered [ 1.747571] NET: Registered PF_KCM protocol family [ 1.747764] l2tp_core: L2TP core driver, V2.0 [ 1.747840] l2tp_ppp: PPPoL2TP kernel driver, V2.0 [ 1.747905] l2tp_ip: L2TP IP encapsulation support (L2TPv3) [ 1.747986] l2tp_netlink: L2TP netlink interface [ 1.748089] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3) [ 1.748159] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3) [ 1.748440] 8021q: 802.1Q VLAN Support v1.8 [ 1.751499] microcode: Current revision: 0x00000000 [ 1.780052] sched_clock: Marking stable (1766683546, 10637291)->(1782065924, -4745087) [ 1.787675] Loading compiled-in X.509 certificates [ 1.801719] Key type .fscrypt registered [ 1.801808] Key type fscrypt-provisioning registered [ 1.977379] usb 2-1: new high-speed USB device number 2 using ehci-pci [ 2.007360] ata2: failed to resume link (SControl 0) [ 2.007466] ata2: SATA link down (SStatus 0 SControl 0) [ 2.007560] ata4: failed to resume link (SControl 0) [ 2.007637] ata4: SATA link down (SStatus 0 SControl 0) [ 2.014675] scsi 4:0:1:0: Direct-Access ATA TRANSCEND 0820 PQ: 0 ANSI: 5 [ 2.015504] sd 4:0:1:0: [sda] 15662304 512-byte logical blocks: (8.02 GB/7.47 GiB) [ 2.015640] sd 4:0:1:0: [sda] Write Protect is off [ 2.015710] sd 4:0:1:0: [sda] Mode Sense: 00 3a 00 00 [ 2.015740] sd 4:0:1:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 2.015878] sd 4:0:1:0: [sda] Preferred minimum I/O size 512 bytes [ 2.019446] sda: sda1 [ 2.019921] sd 4:0:1:0: [sda] Attached SCSI disk [ 2.024502] sd 4:0:1:0: Attached scsi generic sg0 type 0 [ 2.127200] usb-storage 2-1:1.0: USB Mass Storage device detected [ 2.127715] scsi host6: usb-storage 2-1:1.0 [ 2.404060] usb 1-2: new low-speed USB device number 2 using uhci_hcd [ 2.660713] input: HID 046a:0011 as /devices/pci0000:00/0000:00:1d.0/usb1/1-2/1-2:1.0/0003:046A:0011.0001/input/input2 [ 2.724338] hid-generic 0003:046A:0011.0001: input,hidraw0: USB HID v1.11 Keyboard [HID 046a:0011] on usb-0000:00:1d.0-2/input0 [ 3.134868] scsi 6:0:0:0: Direct-Access Kingston DataTraveler 2.0 1.00 PQ: 0 ANSI: 2 [ 3.135709] sd 6:0:0:0: Attached scsi generic sg1 type 0 [ 3.138335] sd 6:0:0:0: [sdb] 2007040 512-byte logical blocks: (1.03 GB/980 MiB) [ 3.139098] sd 6:0:0:0: [sdb] Write Protect is off [ 3.139181] sd 6:0:0:0: [sdb] Mode Sense: 23 00 00 00 [ 3.139853] sd 6:0:0:0: [sdb] No Caching mode page found [ 3.139937] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 3.147229] sdb: sdb1 [ 3.147571] sd 6:0:0:0: [sdb] Attached SCSI removable disk [ 7.764790] Freeing initrd memory: 91572K [ 7.855862] Key type encrypted registered [ 7.856266] gtp: GTP module loaded (pdp ctx size 60 bytes) [ 7.856513] clk: Disabling unused clocks [ 7.857122] Freeing unused kernel image (initmem) memory: 632K [ 7.857773] Write protecting kernel text and read-only data: 16000k [ 7.857865] rodata_test: all tests were successful [ 7.857942] Run /init as init process [ 7.858004] with arguments: [ 7.858007] /init [ 7.858010] with environment: [ 7.858013] HOME=/ [ 7.858017] TERM=linux [ 7.858020] BOOT_IMAGE=kernel [ 12.323994] random: crng init done
Am 2024-04-04 17:57, schrieb Greg Kroah-Hartman:
On Thu, Apr 04, 2024 at 02:07:11PM +0200, Wolfgang Walter wrote:
Hello,
after upgrading to v6.6.24 from v6.6.23 some old boxes (i686; Intel Celeron M) stop to boot:
They hang after:
Decompressing Linux... Parsing ELF... No relocation needed... done. Booting the kernel (entry_offset: 0x00000000).
After some minutes they reboot.
I bisected this down to
commit bebb5af001dc6cb4f505bb21c4d5e2efbdc112e2 Author: Thomas Gleixner tglx@linutronix.de Date: Fri Mar 22 19:56:39 2024 +0100
x86/mpparse: Register APIC address only once [ Upstream commit f2208aa12c27bfada3c15c550c03ca81d42dcac2 ] The APIC address is registered twice. First during the earlydetection and afterwards when actually scanning the table for APIC IDs. The APIC and topology core warn about the second attempt.
Restrict it to the early detection call. Fixes: 81287ad65da5 ("x86/apic: Sanitize APIC address setup") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Tested-by: Guenter Roeck <linux@roeck-us.net> Link:https://lore.kernel.org/r/20240322185305.297774848@linutronix.de Signed-off-by: Sasha Levin sashal@kernel.org
Reverting this commit in v6.6.24 solves the problem.
Is this also an issue in 6.9-rc1 or newer or 6.8.3 or newer?
It is not an issue with 6.9-rc1. 6.9-rc1 just boots fine.
Regards,
On Fri, Apr 05 2024 at 12:35, Wolfgang Walter wrote:
Am 2024-04-04 17:57, schrieb Greg Kroah-Hartman:
Is this also an issue in 6.9-rc1 or newer or 6.8.3 or newer?
It is not an issue with 6.9-rc1. 6.9-rc1 just boots fine.
Bah. That's my fault.
So before the topology evaluation rework landed in the 6.9 merge window this eventual double registration was harmless and only happening for a particular set of AMD machines. The topo rework restructured the whole procedure and caused the new warnings to trigger.
So the Fixes tag I added to that commit was pointing at the wrong place and this needs to be reverted from all pre 6.9 stable kernels.
Sorry for the inconvenience.
Thanks,
tglx
On Fri, Apr 05, 2024 at 01:27:09PM +0200, Thomas Gleixner wrote:
On Fri, Apr 05 2024 at 12:35, Wolfgang Walter wrote:
Am 2024-04-04 17:57, schrieb Greg Kroah-Hartman:
Is this also an issue in 6.9-rc1 or newer or 6.8.3 or newer?
It is not an issue with 6.9-rc1. 6.9-rc1 just boots fine.
Bah. That's my fault.
So before the topology evaluation rework landed in the 6.9 merge window this eventual double registration was harmless and only happening for a particular set of AMD machines. The topo rework restructured the whole procedure and caused the new warnings to trigger.
So the Fixes tag I added to that commit was pointing at the wrong place and this needs to be reverted from all pre 6.9 stable kernels.
Sure, will be glad to, but what git is is "this"? The original report is gone from my thread here, sorry.
greg k-h
On Fri, Apr 05 2024 at 13:34, Greg Kroah-Hartman wrote:
On Fri, Apr 05, 2024 at 01:27:09PM +0200, Thomas Gleixner wrote:
On Fri, Apr 05 2024 at 12:35, Wolfgang Walter wrote:
Am 2024-04-04 17:57, schrieb Greg Kroah-Hartman:
Is this also an issue in 6.9-rc1 or newer or 6.8.3 or newer?
It is not an issue with 6.9-rc1. 6.9-rc1 just boots fine.
Bah. That's my fault.
So before the topology evaluation rework landed in the 6.9 merge window this eventual double registration was harmless and only happening for a particular set of AMD machines. The topo rework restructured the whole procedure and caused the new warnings to trigger.
So the Fixes tag I added to that commit was pointing at the wrong place and this needs to be reverted from all pre 6.9 stable kernels.
Sure, will be glad to, but what git is is "this"? The original report is gone from my thread here, sorry.
The upstream commit with the bogus Fixes tag is:
f2208aa12c27 ("x86/mpparse: Register APIC address only once")
On Fri, Apr 05, 2024 at 04:55:33PM +0200, Thomas Gleixner wrote:
On Fri, Apr 05 2024 at 13:34, Greg Kroah-Hartman wrote:
On Fri, Apr 05, 2024 at 01:27:09PM +0200, Thomas Gleixner wrote:
On Fri, Apr 05 2024 at 12:35, Wolfgang Walter wrote:
Am 2024-04-04 17:57, schrieb Greg Kroah-Hartman:
Is this also an issue in 6.9-rc1 or newer or 6.8.3 or newer?
It is not an issue with 6.9-rc1. 6.9-rc1 just boots fine.
Bah. That's my fault.
So before the topology evaluation rework landed in the 6.9 merge window this eventual double registration was harmless and only happening for a particular set of AMD machines. The topo rework restructured the whole procedure and caused the new warnings to trigger.
So the Fixes tag I added to that commit was pointing at the wrong place and this needs to be reverted from all pre 6.9 stable kernels.
Sure, will be glad to, but what git is is "this"? The original report is gone from my thread here, sorry.
The upstream commit with the bogus Fixes tag is:
f2208aa12c27 ("x86/mpparse: Register APIC address only once")
Thanks, now reverted.
greg k-h
linux-stable-mirror@lists.linaro.org
-
Greg Kroah-Hartman -
Thomas Gleixner -
Wolfgang Walter