4.20-stable review patch. If anyone has any objections, please let me know.
------------------
From: Martin Kepplinger martin.kepplinger@ginzinger.com
commit d5d27fd9826b59979b184ec288e4812abac0e988 upstream.
Disable BCH soft reset according to MX23 erratum #2847 ("BCH soft reset may cause bus master lock up") for MX28 too. It has the same problem.
Observed problem: once per 100,000+ MX28 reboots NAND read failed on DMA timeout errors: [ 1.770823] UBI: attaching mtd3 to ubi0 [ 2.768088] gpmi_nand: DMA timeout, last DMA :1 [ 3.958087] gpmi_nand: BCH timeout, last DMA :1 [ 4.156033] gpmi_nand: Error in ECC-based read: -110 [ 4.161136] UBI warning: ubi_io_read: error -110 while reading 64 bytes from PEB 0:0, read only 0 bytes, retry [ 4.171283] step 1 error [ 4.173846] gpmi_nand: Chip: 0, Error -1
Without BCH soft reset we successfully executed 1,000,000 MX28 reboots.
I have a quote from NXP regarding this problem, from July 18th 2016:
"As the i.MX23 and i.MX28 are of the same generation, they share many characteristics. Unfortunately, also the erratas may be shared. In case of the documented erratas and the workarounds, you can also apply the workaround solution of one device on the other one. This have been reported, but I’m afraid that there are not an estimated date for updating the Errata documents. Please accept our apologies for any inconveniences this may cause."
Fixes: 6f2a6a52560a ("mtd: nand: gpmi: reset BCH earlier, too, to avoid NAND startup problems") Cc: stable@vger.kernel.org Signed-off-by: Manfred Schlaegl manfred.schlaegl@ginzinger.com Signed-off-by: Martin Kepplinger martin.kepplinger@ginzinger.com Reviewed-by: Miquel Raynal miquel.raynal@bootlin.com Reviewed-by: Fabio Estevam festevam@gmail.com Acked-by: Han Xu han.xu@nxp.com Signed-off-by: Boris Brezillon bbrezillon@kernel.org Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org
--- drivers/mtd/nand/raw/gpmi-nand/gpmi-lib.c | 13 ++++++------- 1 file changed, 6 insertions(+), 7 deletions(-)
--- a/drivers/mtd/nand/raw/gpmi-nand/gpmi-lib.c +++ b/drivers/mtd/nand/raw/gpmi-nand/gpmi-lib.c @@ -155,9 +155,10 @@ int gpmi_init(struct gpmi_nand_data *thi
/* * Reset BCH here, too. We got failures otherwise :( - * See later BCH reset for explanation of MX23 handling + * See later BCH reset for explanation of MX23 and MX28 handling */ - ret = gpmi_reset_block(r->bch_regs, GPMI_IS_MX23(this)); + ret = gpmi_reset_block(r->bch_regs, + GPMI_IS_MX23(this) || GPMI_IS_MX28(this)); if (ret) goto err_out;
@@ -263,12 +264,10 @@ int bch_set_geometry(struct gpmi_nand_da /* * Due to erratum #2847 of the MX23, the BCH cannot be soft reset on this * chip, otherwise it will lock up. So we skip resetting BCH on the MX23. - * On the other hand, the MX28 needs the reset, because one case has been - * seen where the BCH produced ECC errors constantly after 10000 - * consecutive reboots. The latter case has not been seen on the MX23 - * yet, still we don't know if it could happen there as well. + * and MX28. */ - ret = gpmi_reset_block(r->bch_regs, GPMI_IS_MX23(this)); + ret = gpmi_reset_block(r->bch_regs, + GPMI_IS_MX23(this) || GPMI_IS_MX28(this)); if (ret) goto err_out;