From: Song, Yoong Siang yoong.siang.song@intel.com
[ Upstream commit 24877687b375f2c476ffb726ea915fc85df09e3d ]
When link speed is not 100 Mbps, port transmit rate and speed divider are set to 8 and 1000000 respectively. These values are incorrect for CBS idleslope and sendslope HW values calculation if the link speed is not 1 Gbps.
This patch adds switch statement to set the values of port transmit rate and speed divider for 10 Gbps, 5 Gbps, 2.5 Gbps, 1 Gbps, and 100 Mbps. Note that CBS is not supported at 10 Mbps.
Fixes: bc41a6689b30 ("net: stmmac: tc: Remove the speed dependency") Fixes: 1f705bc61aee ("net: stmmac: Add support for CBS QDISC") Signed-off-by: Song, Yoong Siang yoong.siang.song@intel.com Link: https://lore.kernel.org/r/1613655653-11755-1-git-send-email-yoong.siang.song... Signed-off-by: Jakub Kicinski kuba@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- .../net/ethernet/stmicro/stmmac/stmmac_tc.c | 30 ++++++++++++++++--- 1 file changed, 26 insertions(+), 4 deletions(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_tc.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_tc.c index 56985542e2029..44bb133c30007 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_tc.c +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_tc.c @@ -316,6 +316,32 @@ static int tc_setup_cbs(struct stmmac_priv *priv, if (!priv->dma_cap.av) return -EOPNOTSUPP;
+ /* Port Transmit Rate and Speed Divider */ + switch (priv->speed) { + case SPEED_10000: + ptr = 32; + speed_div = 10000000; + break; + case SPEED_5000: + ptr = 32; + speed_div = 5000000; + break; + case SPEED_2500: + ptr = 8; + speed_div = 2500000; + break; + case SPEED_1000: + ptr = 8; + speed_div = 1000000; + break; + case SPEED_100: + ptr = 4; + speed_div = 100000; + break; + default: + return -EOPNOTSUPP; + } + mode_to_use = priv->plat->tx_queues_cfg[queue].mode_to_use; if (mode_to_use == MTL_QUEUE_DCB && qopt->enable) { ret = stmmac_dma_qmode(priv, priv->ioaddr, queue, MTL_QUEUE_AVB); @@ -332,10 +358,6 @@ static int tc_setup_cbs(struct stmmac_priv *priv, priv->plat->tx_queues_cfg[queue].mode_to_use = MTL_QUEUE_DCB; }
- /* Port Transmit Rate and Speed Divider */ - ptr = (priv->speed == SPEED_100) ? 4 : 8; - speed_div = (priv->speed == SPEED_100) ? 100000 : 1000000; - /* Final adjustments for HW */ value = div_s64(qopt->idleslope * 1024ll * ptr, speed_div); priv->plat->tx_queues_cfg[queue].idle_slope = value & GENMASK(31, 0);