From: Linus Walleij linus.walleij@linaro.org
[ Upstream commit aeceecd40d94ed3c00bfe1cfe59dd1bfac2fc6fe ]
The TVK1281618 R3 sensors are different from the R2 board, some incorrectness is fixed and some new sensors added, we also rename the nodes appropriately with accelerometer@ etc.
Signed-off-by: Linus Walleij linus.walleij@linaro.org Signed-off-by: Sasha Levin sashal@kernel.org --- arch/arm/boot/dts/ste-href-tvk1281618-r3.dtsi | 73 +++++++++++++------ 1 file changed, 50 insertions(+), 23 deletions(-)
diff --git a/arch/arm/boot/dts/ste-href-tvk1281618-r3.dtsi b/arch/arm/boot/dts/ste-href-tvk1281618-r3.dtsi index 9f285c7cf914..c0de1337bdaa 100644 --- a/arch/arm/boot/dts/ste-href-tvk1281618-r3.dtsi +++ b/arch/arm/boot/dts/ste-href-tvk1281618-r3.dtsi @@ -8,37 +8,43 @@ / { soc { i2c@80128000 { - /* Marked: - * 129 - * M35 - * L3GD20 - */ - l3gd20@6a { - /* Gyroscope */ - compatible = "st,l3gd20"; - status = "disabled"; + accelerometer@19 { + compatible = "st,lsm303dlhc-accel"; st,drdy-int-pin = <1>; - drive-open-drain; - reg = <0x6a>; // 0x6a or 0x6b + reg = <0x19>; vdd-supply = <&ab8500_ldo_aux1_reg>; vddio-supply = <&db8500_vsmps2_reg>; + interrupt-parent = <&gpio2>; + interrupts = <18 IRQ_TYPE_EDGE_RISING>, + <19 IRQ_TYPE_EDGE_RISING>; + pinctrl-names = "default"; + pinctrl-0 = <&accel_tvk_mode>; }; - /* - * Marked: - * 2122 - * C3H - * DQEEE - * LIS3DH? - */ - lis3dh@18 { - /* Accelerometer */ - compatible = "st,lis3dh-accel"; + magnetometer@1e { + compatible = "st,lsm303dlm-magn"; st,drdy-int-pin = <1>; - reg = <0x18>; + reg = <0x1e>; vdd-supply = <&ab8500_ldo_aux1_reg>; vddio-supply = <&db8500_vsmps2_reg>; + // This interrupt is not properly working with the driver + // interrupt-parent = <&gpio1>; + // interrupts = <0 IRQ_TYPE_EDGE_RISING>; pinctrl-names = "default"; - pinctrl-0 = <&accel_tvk_mode>; + pinctrl-0 = <&magn_tvk_mode>; + }; + gyroscope@68 { + /* Gyroscope */ + compatible = "st,l3g4200d-gyro"; + reg = <0x68>; + vdd-supply = <&ab8500_ldo_aux1_reg>; + vddio-supply = <&db8500_vsmps2_reg>; + }; + pressure@5c { + /* Barometer/pressure sensor */ + compatible = "st,lps001wp-press"; + reg = <0x5c>; + vdd-supply = <&ab8500_ldo_aux1_reg>; + vddio-supply = <&db8500_vsmps2_reg>; }; };
@@ -54,5 +60,26 @@ }; }; }; + + pinctrl { + accelerometer { + accel_tvk_mode: accel_tvk { + /* Accelerometer interrupt lines 1 & 2 */ + tvk_cfg { + pins = "GPIO82_C1", "GPIO83_D3"; + ste,config = <&gpio_in_pd>; + }; + }; + }; + magnetometer { + magn_tvk_mode: magn_tvk { + /* GPIO 32 used for DRDY, pull this down */ + tvk_cfg { + pins = "GPIO32_V2"; + ste,config = <&gpio_in_pd>; + }; + }; + }; + }; }; };