Currently, the onboard Cypress CYUSB3304 USB hub is not defined in the device tree, and hub reset pin is provided as vcc5v0_host regulator to usb phy. This causes instability issues, as a result of improper reset duration.
The fixed regulator device requests the GPIO during probe in its inactive state (except if regulator-boot-on property is set, in which case it is requested in the active state). Considering gpio is GPIO_ACTIVE_LOW for Puma, it means it’s driving it high. Then the regulator gets enabled (because regulator-always-on property), which drives it to its active state, meaning driving it low.
The Cypress CYUSB3304 USB hub actually requires the reset to be asserted for at least 5 ms, which we cannot guarantee right now since there's no delay in the current config, meaning the hub may sometimes work or not. We could add delay as offered by fixed-regulator but let's rather fix this by using the proper way to model onboard USB hubs.
Define hub_2_0 and hub_3_0 nodes, as the onboard Cypress hub consist of two 'logical' hubs, for USB2.0 and USB3.0. Use the 'reset-gpios' property of hub to assign reset pin instead of using regulator. Rename the vcc5v0_host regulator to cy3304_reset to be more meaningful. The vdd-supply and vdd2-supply properties in hub nodes were skipped, because hub power supplies are always enabled based on HW design.
Fixes: 2c66fc34e945 ("arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM") Cc: stable@vger.kernel.org # 6.6 Cc: stable@vger.kernel.org # Backport of the patch in this series fixing product ID in onboard_dev_id_table and onboard_dev_match in drivers/usb/misc/onboard_usb_dev.{c,h} driver Signed-off-by: Lukasz Czechowski lukasz.czechowski@thaumatec.com --- arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi | 33 ++++++++++++++++----------- 1 file changed, 20 insertions(+), 13 deletions(-)
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi index 995b30a7aae0..3a9049372e12 100644 --- a/arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi +++ b/arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi @@ -60,16 +60,6 @@ vcc3v3_sys: regulator-vcc3v3-sys { vin-supply = <&vcc5v0_sys>; };
- vcc5v0_host: regulator-vcc5v0-host { - compatible = "regulator-fixed"; - gpio = <&gpio4 RK_PA3 GPIO_ACTIVE_LOW>; - pinctrl-names = "default"; - pinctrl-0 = <&vcc5v0_host_en>; - regulator-name = "vcc5v0_host"; - regulator-always-on; - vin-supply = <&vcc5v0_sys>; - }; - vcc5v0_sys: regulator-vcc5v0-sys { compatible = "regulator-fixed"; regulator-name = "vcc5v0_sys"; @@ -521,8 +511,8 @@ pmic_int_l: pmic-int-l { }; };
- usb2 { - vcc5v0_host_en: vcc5v0-host-en { + usb { + cy3304_reset: cy3304-reset { rockchip,pins = <4 RK_PA3 RK_FUNC_GPIO &pcfg_pull_none>; }; @@ -591,7 +581,6 @@ u2phy1_otg: otg-port { };
u2phy1_host: host-port { - phy-supply = <&vcc5v0_host>; status = "okay"; }; }; @@ -603,6 +592,24 @@ &usbdrd3_1 { &usbdrd_dwc3_1 { status = "okay"; dr_mode = "host"; + pinctrl-names = "default"; + pinctrl-0 = <&cy3304_reset>; + #address-cells = <1>; + #size-cells = <0>; + + hub_2_0: hub@1 { + compatible = "usb4b4,6502"; + reg = <1>; + peer-hub = <&hub_3_0>; + reset-gpios = <&gpio4 RK_PA3 GPIO_ACTIVE_HIGH>; + }; + + hub_3_0: hub@2 { + compatible = "usb4b4,6500"; + reg = <2>; + peer-hub = <&hub_2_0>; + reset-gpios = <&gpio4 RK_PA3 GPIO_ACTIVE_HIGH>; + }; };
&usb_host1_ehci {