From: Dongchun Zhu dongchun.zhu@mediatek.com
[ Upstream commit f1a64f56663e9d03e509439016dcbddd0166b2da ]
From the measured hardware signal, OV5695 reset pin goes high for a
short period of time during boot-up. From the sensor specification, the reset pin is active low and the DT binding defines the pin as active low, which means that the values set by the driver are inverted and thus the value requested in probe ends up high.
Fix it by changing probe to request the reset GPIO initialized to high, which makes the initial state of the physical signal low.
In addition, DOVDD rising must occur before DVDD rising from spec., but regulator_bulk_enable() API enables all the regulators asynchronously. Use an explicit loops of regulator_enable() instead.
For power off sequence, it is required that DVDD falls first. Given the bulk API does not give any guarantee about the order of regulators, change the driver to use regulator_disable() instead.
The sensor also requires a delay between reset high and first I2C transaction, which was assumed to be 8192 XVCLK cycles, but 1ms is recommended by the vendor. Fix this as well.
Signed-off-by: Dongchun Zhu dongchun.zhu@mediatek.com Signed-off-by: Tomasz Figa tfiga@chromium.org Signed-off-by: Sakari Ailus sakari.ailus@linux.intel.com Signed-off-by: Mauro Carvalho Chehab mchehab+huawei@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/media/i2c/ov5695.c | 49 ++++++++++++++++++++++++-------------- 1 file changed, 31 insertions(+), 18 deletions(-)
diff --git a/drivers/media/i2c/ov5695.c b/drivers/media/i2c/ov5695.c index d6cd15bb699ac..cc678d9d2e0da 100644 --- a/drivers/media/i2c/ov5695.c +++ b/drivers/media/i2c/ov5695.c @@ -971,16 +971,9 @@ unlock_and_return: return ret; }
-/* Calculate the delay in us by clock rate and clock cycles */ -static inline u32 ov5695_cal_delay(u32 cycles) -{ - return DIV_ROUND_UP(cycles, OV5695_XVCLK_FREQ / 1000 / 1000); -} - static int __ov5695_power_on(struct ov5695 *ov5695) { - int ret; - u32 delay_us; + int i, ret; struct device *dev = &ov5695->client->dev;
ret = clk_prepare_enable(ov5695->xvclk); @@ -991,21 +984,28 @@ static int __ov5695_power_on(struct ov5695 *ov5695)
gpiod_set_value_cansleep(ov5695->reset_gpio, 1);
- ret = regulator_bulk_enable(OV5695_NUM_SUPPLIES, ov5695->supplies); - if (ret < 0) { - dev_err(dev, "Failed to enable regulators\n"); - goto disable_clk; + /* + * The hardware requires the regulators to be powered on in order, + * so enable them one by one. + */ + for (i = 0; i < OV5695_NUM_SUPPLIES; i++) { + ret = regulator_enable(ov5695->supplies[i].consumer); + if (ret) { + dev_err(dev, "Failed to enable %s: %d\n", + ov5695->supplies[i].supply, ret); + goto disable_reg_clk; + } }
gpiod_set_value_cansleep(ov5695->reset_gpio, 0);
- /* 8192 cycles prior to first SCCB transaction */ - delay_us = ov5695_cal_delay(8192); - usleep_range(delay_us, delay_us * 2); + usleep_range(1000, 1200);
return 0;
-disable_clk: +disable_reg_clk: + for (--i; i >= 0; i--) + regulator_disable(ov5695->supplies[i].consumer); clk_disable_unprepare(ov5695->xvclk);
return ret; @@ -1013,9 +1013,22 @@ disable_clk:
static void __ov5695_power_off(struct ov5695 *ov5695) { + struct device *dev = &ov5695->client->dev; + int i, ret; + clk_disable_unprepare(ov5695->xvclk); gpiod_set_value_cansleep(ov5695->reset_gpio, 1); - regulator_bulk_disable(OV5695_NUM_SUPPLIES, ov5695->supplies); + + /* + * The hardware requires the regulators to be powered off in order, + * so disable them one by one. + */ + for (i = OV5695_NUM_SUPPLIES - 1; i >= 0; i--) { + ret = regulator_disable(ov5695->supplies[i].consumer); + if (ret) + dev_err(dev, "Failed to disable %s: %d\n", + ov5695->supplies[i].supply, ret); + } }
static int __maybe_unused ov5695_runtime_resume(struct device *dev) @@ -1285,7 +1298,7 @@ static int ov5695_probe(struct i2c_client *client, if (clk_get_rate(ov5695->xvclk) != OV5695_XVCLK_FREQ) dev_warn(dev, "xvclk mismatched, modes are based on 24MHz\n");
- ov5695->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW); + ov5695->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH); if (IS_ERR(ov5695->reset_gpio)) { dev_err(dev, "Failed to get reset-gpios\n"); return -EINVAL;