From: Finn Thain fthain@telegraphics.com.au
commit 27e0c31c5f27c1d1a1d9d135c123069f60dcf97b upstream.
There are several issues relating to command register usage during chip initialization.
Firstly, the SONIC sometimes comes out of software reset with the Start Timer bit set. This gets logged as,
macsonic macsonic eth0: sonic_init: status=24, i=101
Avoid this by giving the Stop Timer command earlier than later.
Secondly, the loop that waits for the Read RRA command to complete has the break condition inverted. That's why the for loop iterates until its termination condition. Call the helper for this instead.
Finally, give the Receiver Enable command after clearing interrupts, not before, to avoid the possibility of losing an interrupt.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Tested-by: Stan Johnson userm57@yahoo.com Signed-off-by: Finn Thain fthain@telegraphics.com.au Signed-off-by: David S. Miller davem@davemloft.net Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org
--- drivers/net/ethernet/natsemi/sonic.c | 18 +++--------------- 1 file changed, 3 insertions(+), 15 deletions(-)
--- a/drivers/net/ethernet/natsemi/sonic.c +++ b/drivers/net/ethernet/natsemi/sonic.c @@ -663,7 +663,6 @@ static void sonic_multicast_list(struct */ static int sonic_init(struct net_device *dev) { - unsigned int cmd; struct sonic_local *lp = netdev_priv(dev); int i;
@@ -680,7 +679,7 @@ static int sonic_init(struct net_device * enable interrupts, then completely initialize the SONIC */ SONIC_WRITE(SONIC_CMD, 0); - SONIC_WRITE(SONIC_CMD, SONIC_CR_RXDIS); + SONIC_WRITE(SONIC_CMD, SONIC_CR_RXDIS | SONIC_CR_STP); sonic_quiesce(dev, SONIC_CR_ALL);
/* @@ -710,14 +709,7 @@ static int sonic_init(struct net_device netif_dbg(lp, ifup, dev, "%s: issuing RRRA command\n", __func__);
SONIC_WRITE(SONIC_CMD, SONIC_CR_RRRA); - i = 0; - while (i++ < 100) { - if (SONIC_READ(SONIC_CMD) & SONIC_CR_RRRA) - break; - } - - netif_dbg(lp, ifup, dev, "%s: status=%x, i=%d\n", __func__, - SONIC_READ(SONIC_CMD), i); + sonic_quiesce(dev, SONIC_CR_RRRA);
/* * Initialize the receive descriptors so that they @@ -805,15 +797,11 @@ static int sonic_init(struct net_device * enable receiver, disable loopback * and enable all interrupts */ - SONIC_WRITE(SONIC_CMD, SONIC_CR_RXEN | SONIC_CR_STP); SONIC_WRITE(SONIC_RCR, SONIC_RCR_DEFAULT); SONIC_WRITE(SONIC_TCR, SONIC_TCR_DEFAULT); SONIC_WRITE(SONIC_ISR, 0x7fff); SONIC_WRITE(SONIC_IMR, SONIC_IMR_DEFAULT); - - cmd = SONIC_READ(SONIC_CMD); - if ((cmd & SONIC_CR_RXEN) == 0 || (cmd & SONIC_CR_STP) == 0) - printk(KERN_ERR "sonic_init: failed, status=%x\n", cmd); + SONIC_WRITE(SONIC_CMD, SONIC_CR_RXEN);
netif_dbg(lp, ifup, dev, "%s: new status=%x\n", __func__, SONIC_READ(SONIC_CMD));