From: Douglas Anderson dianders@chromium.org
[ Upstream commit 02b9aec59243c6240fc42884acc958602146ddf6 ]
When I have KASAN enabled on my kernel and I start stressing the touchscreen my system tends to hang. The touchscreen is one of the only things that does a lot of big i2c transfers and ends up hitting the DMA paths in the geni i2c driver. It appears that KASAN adds enough delay in my system to tickle a race condition in the DMA setup code.
When the system hangs, I found that it was running the geni_i2c_irq() over and over again. It had these:
m_stat = 0x04000080 rx_st = 0x30000011 dm_tx_st = 0x00000000 dm_rx_st = 0x00000000 dma = 0x00000001
Notably we're in DMA mode but are getting M_RX_IRQ_EN and M_RX_FIFO_WATERMARK_EN over and over again.
Putting some traces in geni_i2c_rx_one_msg() showed that when we failed we were getting to the start of geni_i2c_rx_one_msg() but were never executing geni_se_rx_dma_prep().
I believe that the problem here is that we are starting the geni command before we run geni_se_rx_dma_prep(). If a transfer makes it far enough before we do that then we get into the state I have observed. Let's change the order, which seems to work fine.
Although problems were seen on the RX path, code inspection suggests that the TX should be changed too. Change it as well.
Fixes: 37692de5d523 ("i2c: i2c-qcom-geni: Add bus driver for the Qualcomm GENI I2C controller") Signed-off-by: Douglas Anderson dianders@chromium.org Tested-by: Sai Prakash Ranjan saiprakash.ranjan@codeaurora.org Reviewed-by: Akash Asthana akashast@codeaurora.org Reviewed-by: Stephen Boyd swboyd@chromium.org Reviewed-by: Mukesh Kumar Savaliya msavaliy@codeaurora.org Signed-off-by: Wolfram Sang wsa@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/i2c/busses/i2c-qcom-geni.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-)
diff --git a/drivers/i2c/busses/i2c-qcom-geni.c b/drivers/i2c/busses/i2c-qcom-geni.c index 17abf60c94aeb..aafc76ee93e02 100644 --- a/drivers/i2c/busses/i2c-qcom-geni.c +++ b/drivers/i2c/busses/i2c-qcom-geni.c @@ -368,7 +368,6 @@ static int geni_i2c_rx_one_msg(struct geni_i2c_dev *gi2c, struct i2c_msg *msg, geni_se_select_mode(se, GENI_SE_FIFO);
writel_relaxed(len, se->base + SE_I2C_RX_TRANS_LEN); - geni_se_setup_m_cmd(se, I2C_READ, m_param);
if (dma_buf && geni_se_rx_dma_prep(se, dma_buf, len, &rx_dma)) { geni_se_select_mode(se, GENI_SE_FIFO); @@ -376,6 +375,8 @@ static int geni_i2c_rx_one_msg(struct geni_i2c_dev *gi2c, struct i2c_msg *msg, dma_buf = NULL; }
+ geni_se_setup_m_cmd(se, I2C_READ, m_param); + time_left = wait_for_completion_timeout(&gi2c->done, XFER_TIMEOUT); if (!time_left) geni_i2c_abort_xfer(gi2c); @@ -409,7 +410,6 @@ static int geni_i2c_tx_one_msg(struct geni_i2c_dev *gi2c, struct i2c_msg *msg, geni_se_select_mode(se, GENI_SE_FIFO);
writel_relaxed(len, se->base + SE_I2C_TX_TRANS_LEN); - geni_se_setup_m_cmd(se, I2C_WRITE, m_param);
if (dma_buf && geni_se_tx_dma_prep(se, dma_buf, len, &tx_dma)) { geni_se_select_mode(se, GENI_SE_FIFO); @@ -417,6 +417,8 @@ static int geni_i2c_tx_one_msg(struct geni_i2c_dev *gi2c, struct i2c_msg *msg, dma_buf = NULL; }
+ geni_se_setup_m_cmd(se, I2C_WRITE, m_param); + if (!dma_buf) /* Get FIFO IRQ */ writel_relaxed(1, se->base + SE_GENI_TX_WATERMARK_REG);