On Tue, Jun 14, 2022 at 10:31:38AM +0200, Sascha Hauer wrote:
The DEVICE_BUSY_TIMEOUT value is described in the Reference Manual as:
| Timeout waiting for NAND Ready/Busy or ATA IRQ. Used in WAIT_FOR_READY | mode. This value is the number of GPMI_CLK cycles multiplied by 4096.
So instead of multiplying the value in cycles with 4096, we have to divide it by that value. Use DIV_ROUND_UP to make sure we are on the safe side, especially when the calculated value in cycles is smaller than 4096 as typically the case.
This bug likely never triggered because any timeout != 0 usually will do. In my case the busy timeout in cycles was originally calculated as 2408, which multiplied with 4096 is 0x968000. The lower 16 bits were taken for the 16 bit wide register field, so the register value was 0x8000. With 2970bf5a32f0 ("mtd: rawnand: gpmi: fix controller timings setting") however the value in cycles became 2384, which multiplied with 4096 is 0x950000. The lower 16 bit are 0x0 now resulting in an intermediate timeout when reading from NAND.
Fixes: b1206122069aa ("mtd: rawnand: gpmi: use core timings instead of an empirical derivation") Cc: stable@vger.kernel.org Signed-off-by: Sascha Hauer s.hauer@pengutronix.de
Just a resend with +Cc: stable@vger.kernel.org
drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c b/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c index 0b68d05846e18..889e403299568 100644 --- a/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c +++ b/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c @@ -890,7 +890,7 @@ static int gpmi_nfc_compute_timings(struct gpmi_nand_data *this, hw->timing0 = BF_GPMI_TIMING0_ADDRESS_SETUP(addr_setup_cycles) | BF_GPMI_TIMING0_DATA_HOLD(data_hold_cycles) | BF_GPMI_TIMING0_DATA_SETUP(data_setup_cycles);
- hw->timing1 = BF_GPMI_TIMING1_BUSY_TIMEOUT(busy_timeout_cycles * 4096);
- hw->timing1 = BF_GPMI_TIMING1_BUSY_TIMEOUT(DIV_ROUND_UP(busy_timeout_cycles, 4096));
This patch is broken. The change itself is fine, but busy_timeout_cycles is calculated wrong.
busy_timeout_cycles is calculated based on sdr->tR_max which is the page read time. This timeout is also used for the page program and block erase operations which have orders of magnitude bigger timeouts. This means with this patch the controller times out on pages programs and block erase operations. With the current code this timeout will be silent as the timeout interrupt is not active.
** THIS PATCH WILL CAUSE DATA LOSS ON YOUR NAND!! **
Fortunately this patch hasn't been included in any mainline release, but unfortunately it showed up in several stable kernels. Don't use v5.4.202, v5.10.127, v5.15.51 or v5.18.8 on i.MX[678] or i.MX28 boards with NAND.
I am sorry for the trouble I have likely caused. I am working on a fix and will post it later the day.
Sascha