The patch below does not apply to the 6.6-stable tree. If someone wants it applied there, or to any other stable or longterm tree, then please email the backport, including the original git commit id to stable@vger.kernel.org.
To reproduce the conflict and resubmit, you may use the following commands:
git fetch https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/ linux-6.6.y git checkout FETCH_HEAD git cherry-pick -x 7cc0e0a43a91052477c2921f924a37d9c3891f0c # <resolve conflicts, build, test, etc.> git commit -s git send-email --to 'stable@vger.kernel.org' --in-reply-to '2024121530-womanlike-motocross-3283@gregkh' --subject-prefix 'PATCH 6.6.y' HEAD^..
Possible dependencies:
thanks,
greg k-h
------------------ original commit in Linus's tree ------------------
From 7cc0e0a43a91052477c2921f924a37d9c3891f0c Mon Sep 17 00:00:00 2001 From: Claudiu Beznea claudiu.beznea.uj@bp.renesas.com Date: Mon, 25 Nov 2024 13:58:56 +0200 Subject: [PATCH] serial: sh-sci: Check if TX data was written to device in .tx_empty()
On the Renesas RZ/G3S, when doing suspend to RAM, the uart_suspend_port() is called. The uart_suspend_port() calls 3 times the struct uart_port::ops::tx_empty() before shutting down the port.
According to the documentation, the struct uart_port::ops::tx_empty() API tests whether the transmitter FIFO and shifter for the port is empty.
The Renesas RZ/G3S SCIFA IP reports the number of data units stored in the transmit FIFO through the FDR (FIFO Data Count Register). The data units in the FIFOs are written in the shift register and transmitted from there. The TEND bit in the Serial Status Register reports if the data was transmitted from the shift register.
In the previous code, in the tx_empty() API implemented by the sh-sci driver, it is considered that the TX is empty if the hardware reports the TEND bit set and the number of data units in the FIFO is zero.
According to the HW manual, the TEND bit has the following meaning:
0: Transmission is in the waiting state or in progress. 1: Transmission is completed.
It has been noticed that when opening the serial device w/o using it and then switch to a power saving mode, the tx_empty() call in the uart_port_suspend() function fails, leading to the "Unable to drain transmitter" message being printed on the console. This is because the TEND=0 if nothing has been transmitted and the FIFOs are empty. As the TEND=0 has double meaning (waiting state, in progress) we can't determined the scenario described above.
Add a software workaround for this. This sets a variable if any data has been sent on the serial console (when using PIO) or if the DMA callback has been called (meaning something has been transmitted). In the tx_empty() API the status of the DMA transaction is also checked and if it is completed or in progress the code falls back in checking the hardware registers instead of relying on the software variable.
Fixes: 73a19e4c0301 ("serial: sh-sci: Add DMA support.") Cc: stable@vger.kernel.org Signed-off-by: Claudiu Beznea claudiu.beznea.uj@bp.renesas.com Link: https://lore.kernel.org/r/20241125115856.513642-1-claudiu.beznea.uj@bp.renes... Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org
diff --git a/drivers/tty/serial/sh-sci.c b/drivers/tty/serial/sh-sci.c index df523c744423..924b803af440 100644 --- a/drivers/tty/serial/sh-sci.c +++ b/drivers/tty/serial/sh-sci.c @@ -157,6 +157,7 @@ struct sci_port {
bool has_rtscts; bool autorts; + bool tx_occurred; };
#define SCI_NPORTS CONFIG_SERIAL_SH_SCI_NR_UARTS @@ -850,6 +851,7 @@ static void sci_transmit_chars(struct uart_port *port) { struct tty_port *tport = &port->state->port; unsigned int stopped = uart_tx_stopped(port); + struct sci_port *s = to_sci_port(port); unsigned short status; unsigned short ctrl; int count; @@ -885,6 +887,7 @@ static void sci_transmit_chars(struct uart_port *port) }
sci_serial_out(port, SCxTDR, c); + s->tx_occurred = true;
port->icount.tx++; } while (--count > 0); @@ -1241,6 +1244,8 @@ static void sci_dma_tx_complete(void *arg) if (kfifo_len(&tport->xmit_fifo) < WAKEUP_CHARS) uart_write_wakeup(port);
+ s->tx_occurred = true; + if (!kfifo_is_empty(&tport->xmit_fifo)) { s->cookie_tx = 0; schedule_work(&s->work_tx); @@ -1731,6 +1736,19 @@ static void sci_flush_buffer(struct uart_port *port) s->cookie_tx = -EINVAL; } } + +static void sci_dma_check_tx_occurred(struct sci_port *s) +{ + struct dma_tx_state state; + enum dma_status status; + + if (!s->chan_tx) + return; + + status = dmaengine_tx_status(s->chan_tx, s->cookie_tx, &state); + if (status == DMA_COMPLETE || status == DMA_IN_PROGRESS) + s->tx_occurred = true; +} #else /* !CONFIG_SERIAL_SH_SCI_DMA */ static inline void sci_request_dma(struct uart_port *port) { @@ -1740,6 +1758,10 @@ static inline void sci_free_dma(struct uart_port *port) { }
+static void sci_dma_check_tx_occurred(struct sci_port *s) +{ +} + #define sci_flush_buffer NULL #endif /* !CONFIG_SERIAL_SH_SCI_DMA */
@@ -2076,6 +2098,12 @@ static unsigned int sci_tx_empty(struct uart_port *port) { unsigned short status = sci_serial_in(port, SCxSR); unsigned short in_tx_fifo = sci_txfill(port); + struct sci_port *s = to_sci_port(port); + + sci_dma_check_tx_occurred(s); + + if (!s->tx_occurred) + return TIOCSER_TEMT;
return (status & SCxSR_TEND(port)) && !in_tx_fifo ? TIOCSER_TEMT : 0; } @@ -2247,6 +2275,7 @@ static int sci_startup(struct uart_port *port)
dev_dbg(port->dev, "%s(%d)\n", __func__, port->line);
+ s->tx_occurred = false; sci_request_dma(port);
ret = sci_request_irq(s);