From: Damien Le Moal damien.lemoal@opensource.wdc.com
commit 68dbbe7d5b4fde736d104cbbc9a2fce875562012 upstream.
Some ATA drives are very slow to respond to READ_LOG_EXT and READ_LOG_DMA_EXT commands issued from ata_dev_configure() when the device is revalidated right after resuming a system or inserting the ATA adapter driver (e.g. ahci). The default 5s timeout (ATA_EH_CMD_DFL_TIMEOUT) used for these commands is too short, causing errors during the device configuration. Ex:
... ata9: SATA max UDMA/133 abar m524288@0x9d200000 port 0x9d200400 irq 209 ata9: SATA link up 6.0 Gbps (SStatus 133 SControl 300) ata9.00: ATA-9: XXX XXXXXXXXXXXXXXX, XXXXXXXX, max UDMA/133 ata9.00: qc timeout (cmd 0x2f) ata9.00: Read log page 0x00 failed, Emask 0x4 ata9.00: Read log page 0x00 failed, Emask 0x40 ata9.00: NCQ Send/Recv Log not supported ata9.00: Read log page 0x08 failed, Emask 0x40 ata9.00: 27344764928 sectors, multi 16: LBA48 NCQ (depth 32), AA ata9.00: Read log page 0x00 failed, Emask 0x40 ata9.00: ATA Identify Device Log not supported ata9.00: failed to set xfermode (err_mask=0x40) ata9: SATA link up 6.0 Gbps (SStatus 133 SControl 300) ata9.00: configured for UDMA/133 ...
The timeout error causes a soft reset of the drive link, followed in most cases by a successful revalidation as that give enough time to the drive to become fully ready to quickly process the read log commands. However, in some cases, this also fails resulting in the device being dropped.
Fix this by using adding the ata_eh_revalidate_timeouts entries for the READ_LOG_EXT and READ_LOG_DMA_EXT commands. This defines a timeout increased to 15s, retriable one time.
Reported-by: Geert Uytterhoeven geert@linux-m68k.org Tested-by: Geert Uytterhoeven geert+renesas@glider.be Cc: stable@vger.kernel.org Signed-off-by: Damien Le Moal damien.lemoal@opensource.wdc.com Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- drivers/ata/libata-eh.c | 8 ++++++++ include/linux/libata.h | 2 +- 2 files changed, 9 insertions(+), 1 deletion(-)
--- a/drivers/ata/libata-eh.c +++ b/drivers/ata/libata-eh.c @@ -114,6 +114,12 @@ static const unsigned long ata_eh_identi ULONG_MAX, };
+static const unsigned long ata_eh_revalidate_timeouts[] = { + 15000, /* Some drives are slow to read log pages when waking-up */ + 15000, /* combined time till here is enough even for media access */ + ULONG_MAX, +}; + static const unsigned long ata_eh_flush_timeouts[] = { 15000, /* be generous with flush */ 15000, /* ditto */ @@ -150,6 +156,8 @@ static const struct ata_eh_cmd_timeout_e ata_eh_cmd_timeout_table[ATA_EH_CMD_TIMEOUT_TABLE_SIZE] = { { .commands = CMDS(ATA_CMD_ID_ATA, ATA_CMD_ID_ATAPI), .timeouts = ata_eh_identify_timeouts, }, + { .commands = CMDS(ATA_CMD_READ_LOG_EXT, ATA_CMD_READ_LOG_DMA_EXT), + .timeouts = ata_eh_revalidate_timeouts, }, { .commands = CMDS(ATA_CMD_READ_NATIVE_MAX, ATA_CMD_READ_NATIVE_MAX_EXT), .timeouts = ata_eh_other_timeouts, }, { .commands = CMDS(ATA_CMD_SET_MAX, ATA_CMD_SET_MAX_EXT), --- a/include/linux/libata.h +++ b/include/linux/libata.h @@ -408,7 +408,7 @@ enum { /* This should match the actual table size of * ata_eh_cmd_timeout_table in libata-eh.c. */ - ATA_EH_CMD_TIMEOUT_TABLE_SIZE = 6, + ATA_EH_CMD_TIMEOUT_TABLE_SIZE = 7,
/* Horkage types. May be set by libata or controller on drives (some horkage may be drive/controller pair dependent */