From: Douglas Anderson dianders@chromium.org
[ Upstream commit 1cf86bc21257a330e3af51f2a4e885f1a705f6a5 ]
If you do this on an sdm845 board: grep "" /sys/kernel/debug/pinctrl/*spmi:pmic*/pinconf-groups
...it looks like nonsense. For every pin you see listed: input bias disabled, input bias high impedance, input bias pull down, input bias pull up, ...
That's because pmic_gpio_config_get() isn't complying with the rules that pinconf_generic_dump_one() expects. Specifically for boolean parameters (anything with a "struct pin_config_item" where has_arg is false) the function expects that the function should return its value not through the "config" parameter but should return "0" if the value is set and "-EINVAL" if the value isn't set.
Let's fix this.
From a quick sample of other pinctrl drivers, it appears to be
tradition to also return 1 through the config parameter for these boolean parameters when they exist. I'm not one to knock tradition, so I'll follow tradition and return 1 in these cases. While I'm at it, I'll also continue searching for four leaf clovers, kocking on wood three times, and trying not to break mirrors.
NOTE: This also fixes an apparent typo for reading PIN_CONFIG_BIAS_DISABLE where the old driver was accidentally using "=" instead of "==" and thus was setting some internal state when you tried to query PIN_CONFIG_BIAS_DISABLE. Oops.
Fixes: eadff3024472 ("pinctrl: Qualcomm SPMI PMIC GPIO pin controller driver") Signed-off-by: Douglas Anderson dianders@chromium.org Signed-off-by: Linus Walleij linus.walleij@linaro.org Signed-off-by: Sasha Levin alexander.levin@microsoft.com --- drivers/pinctrl/qcom/pinctrl-spmi-gpio.c | 32 ++++++++++++++++++------ 1 file changed, 24 insertions(+), 8 deletions(-)
diff --git a/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c b/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c index c2c0bab04257..22aaf4375fac 100644 --- a/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c +++ b/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c @@ -390,31 +390,47 @@ static int pmic_gpio_config_get(struct pinctrl_dev *pctldev,
switch (param) { case PIN_CONFIG_DRIVE_PUSH_PULL: - arg = pad->buffer_type == PMIC_GPIO_OUT_BUF_CMOS; + if (pad->buffer_type != PMIC_GPIO_OUT_BUF_CMOS) + return -EINVAL; + arg = 1; break; case PIN_CONFIG_DRIVE_OPEN_DRAIN: - arg = pad->buffer_type == PMIC_GPIO_OUT_BUF_OPEN_DRAIN_NMOS; + if (pad->buffer_type != PMIC_GPIO_OUT_BUF_OPEN_DRAIN_NMOS) + return -EINVAL; + arg = 1; break; case PIN_CONFIG_DRIVE_OPEN_SOURCE: - arg = pad->buffer_type == PMIC_GPIO_OUT_BUF_OPEN_DRAIN_PMOS; + if (pad->buffer_type != PMIC_GPIO_OUT_BUF_OPEN_DRAIN_PMOS) + return -EINVAL; + arg = 1; break; case PIN_CONFIG_BIAS_PULL_DOWN: - arg = pad->pullup == PMIC_GPIO_PULL_DOWN; + if (pad->pullup != PMIC_GPIO_PULL_DOWN) + return -EINVAL; + arg = 1; break; case PIN_CONFIG_BIAS_DISABLE: - arg = pad->pullup = PMIC_GPIO_PULL_DISABLE; + if (pad->pullup != PMIC_GPIO_PULL_DISABLE) + return -EINVAL; + arg = 1; break; case PIN_CONFIG_BIAS_PULL_UP: - arg = pad->pullup == PMIC_GPIO_PULL_UP_30; + if (pad->pullup != PMIC_GPIO_PULL_UP_30) + return -EINVAL; + arg = 1; break; case PIN_CONFIG_BIAS_HIGH_IMPEDANCE: - arg = !pad->is_enabled; + if (pad->is_enabled) + return -EINVAL; + arg = 1; break; case PIN_CONFIG_POWER_SOURCE: arg = pad->power_source; break; case PIN_CONFIG_INPUT_ENABLE: - arg = pad->input_enabled; + if (!pad->input_enabled) + return -EINVAL; + arg = 1; break; case PIN_CONFIG_OUTPUT: arg = pad->out_value;