From: Trevor Gamblin tgamblin@baylibre.com
[ Upstream commit 998d20e4e99d909f14d96fdf0bdcf860f7efe3ef ]
Ensure that conversion mode is successfully exited when the command is issued by adding an extra transfer beforehand, matching the minimum CNV high and low times from the AD4695 datasheet. The AD4695 has a quirk where the exit command only works during a conversion, so guarantee this happens by triggering a conversion in ad4695_exit_conversion_mode(). Then make this even more robust by ensuring that the exit command is run at AD4695_REG_ACCESS_SCLK_HZ rather than the bus maximum.
Signed-off-by: Trevor Gamblin tgamblin@baylibre.com Reviewed-by: David Lechner dlechner@baylibre.com Tested-by: David Lechner dlechner@baylibre.com Link: https://patch.msgid.link/20241113-tgamblin-ad4695_improvements-v2-2-b6bb7c75... Signed-off-by: Jonathan Cameron Jonathan.Cameron@huawei.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/iio/adc/ad4695.c | 34 ++++++++++++++++++++++++++++------ 1 file changed, 28 insertions(+), 6 deletions(-)
diff --git a/drivers/iio/adc/ad4695.c b/drivers/iio/adc/ad4695.c index b79d135a54718..22fdc454b0cea 100644 --- a/drivers/iio/adc/ad4695.c +++ b/drivers/iio/adc/ad4695.c @@ -92,6 +92,8 @@ #define AD4695_T_REFBUF_MS 100 #define AD4695_T_REGCONFIG_NS 20 #define AD4695_T_SCK_CNV_DELAY_NS 80 +#define AD4695_T_CNVL_NS 80 +#define AD4695_T_CNVH_NS 10 #define AD4695_REG_ACCESS_SCLK_HZ (10 * MEGA)
/* Max number of voltage input channels. */ @@ -364,11 +366,31 @@ static int ad4695_enter_advanced_sequencer_mode(struct ad4695_state *st, u32 n) */ static int ad4695_exit_conversion_mode(struct ad4695_state *st) { - struct spi_transfer xfer = { - .tx_buf = &st->cnv_cmd2, - .len = 1, - .delay.value = AD4695_T_REGCONFIG_NS, - .delay.unit = SPI_DELAY_UNIT_NSECS, + /* + * An extra transfer is needed to trigger a conversion here so + * that we can be 100% sure the command will be processed by the + * ADC, rather than relying on it to be in the correct state + * when this function is called (this chip has a quirk where the + * command only works when reading a conversion, and if the + * previous conversion was already read then it won't work). The + * actual conversion command is then run at the slower + * AD4695_REG_ACCESS_SCLK_HZ speed to guarantee this works. + */ + struct spi_transfer xfers[] = { + { + .delay.value = AD4695_T_CNVL_NS, + .delay.unit = SPI_DELAY_UNIT_NSECS, + .cs_change = 1, + .cs_change_delay.value = AD4695_T_CNVH_NS, + .cs_change_delay.unit = SPI_DELAY_UNIT_NSECS, + }, + { + .speed_hz = AD4695_REG_ACCESS_SCLK_HZ, + .tx_buf = &st->cnv_cmd2, + .len = 1, + .delay.value = AD4695_T_REGCONFIG_NS, + .delay.unit = SPI_DELAY_UNIT_NSECS, + }, };
/* @@ -377,7 +399,7 @@ static int ad4695_exit_conversion_mode(struct ad4695_state *st) */ st->cnv_cmd2 = AD4695_CMD_EXIT_CNV_MODE << 3;
- return spi_sync_transfer(st->spi, &xfer, 1); + return spi_sync_transfer(st->spi, xfers, ARRAY_SIZE(xfers)); }
static int ad4695_set_ref_voltage(struct ad4695_state *st, int vref_mv)