When the host actively triggers SSR and collects coredump data, the Bluetooth stack sends a reset command to the controller. However, due to the inability to clear the QCA_SSR_TRIGGERED and QCA_IBS_DISABLED bits, the reset command times out.
To address this, this patch clears the QCA_SSR_TRIGGERED and QCA_IBS_DISABLED flags and adds a 50ms delay after SSR, but only when HCI_QUIRK_NON_PERSISTENT_SETUP is not set. This ensures the controller completes the SSR process when BT_EN is always high due to hardware.
For the purpose of HCI_QUIRK_NON_PERSISTENT_SETUP, please refer to the comment in `include/net/bluetooth/hci.h`.
The HCI_QUIRK_NON_PERSISTENT_SETUP quirk is associated with BT_EN, and its presence can be used to determine whether BT_EN is defined in DTS.
After SSR, host will not download the firmware, causing controller to remain in the IBS_WAKE state. Host needs to synchronize with the controller to maintain proper operation.
Multiple triggers of SSR only first generate coredump file, due to memcoredump_flag no clear.
add clear coredump flag when ssr completed.
When the SSR duration exceeds 2 seconds, it triggers host tx_idle_timeout, which sets host TX state to sleep. due to the hardware pulling up bt_en, the firmware is not downloaded after the SSR. As a result, the controller does not enter sleep mode. Consequently, when the host sends a command afterward, it sends 0xFD to the controller, but the controller does not respond, leading to a command timeout.
So reset tx_idle_timer after SSR to prevent host enter TX IBS_Sleep mode.
Changes since v6-7: - Merge the changes into a single patch. - Update commit.
Changes since v1-5: - Add an explanation for HCI_QUIRK_NON_PERSISTENT_SETUP. - Add commments for msleep(50). - Update format and commit.
Signed-off-by: Shuai Zhang quic_shuaz@quicinc.com --- drivers/bluetooth/hci_qca.c | 33 +++++++++++++++++++++++++++++++++ 1 file changed, 33 insertions(+)
diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c index 4e56782b0..9dc59b002 100644 --- a/drivers/bluetooth/hci_qca.c +++ b/drivers/bluetooth/hci_qca.c @@ -1653,6 +1653,39 @@ static void qca_hw_error(struct hci_dev *hdev, u8 code) skb_queue_purge(&qca->rx_memdump_q); }
+ /* + * If the BT chip's bt_en pin is connected to a 3.3V power supply via + * hardware and always stays high, driver cannot control the bt_en pin. + * As a result, during SSR (SubSystem Restart), QCA_SSR_TRIGGERED and + * QCA_IBS_DISABLED flags cannot be cleared, which leads to a reset + * command timeout. + * Add an msleep delay to ensure controller completes the SSR process. + * + * Host will not download the firmware after SSR, controller to remain + * in the IBS_WAKE state, and the host needs to synchronize with it + * + * Since the bluetooth chip has been reset, clear the memdump state. + */ + if (!test_bit(HCI_QUIRK_NON_PERSISTENT_SETUP, &hdev->quirks)) { + /* + * When the SSR (SubSystem Restart) duration exceeds 2 seconds, + * it triggers host tx_idle_delay, which sets host TX state + * to sleep. Reset tx_idle_timer after SSR to prevent + * host enter TX IBS_Sleep mode. + */ + mod_timer(&qca->tx_idle_timer, jiffies + + msecs_to_jiffies(qca->tx_idle_delay)); + + /* Controller reset completion time is 50ms */ + msleep(50); + + clear_bit(QCA_SSR_TRIGGERED, &qca->flags); + clear_bit(QCA_IBS_DISABLED, &qca->flags); + + qca->tx_ibs_state = HCI_IBS_TX_AWAKE; + qca->memdump_state = QCA_MEMDUMP_IDLE; + } + clear_bit(QCA_HW_ERROR_EVENT, &qca->flags); }