From: Lukas Stockmann lukas.stockmann@siemens.com
[ Upstream commit 2b7cbd98495f6ee4cd6422fe77828a19e9edf87f ]
Power-on Reset has a documented issue in PCF85063, refer to its datasheet, section "Software reset":
"There is a low probability that some devices will have corruption of the registers after the automatic power-on reset if the device is powered up with a residual VDD level. It is required that the VDD starts at zero volts at power up or upon power cycling to ensure that there is no corruption of the registers. If this is not possible, a reset must be initiated after power-up (i.e. when power is stable) with the software reset command"
Trigger SW reset if there is an indication that POR has failed.
Link: https://www.nxp.com/docs/en/data-sheet/PCF85063A.pdf Signed-off-by: Lukas Stockmann lukas.stockmann@siemens.com Signed-off-by: Alexander Sverdlin alexander.sverdlin@siemens.com Link: https://lore.kernel.org/r/20250120093451.30778-1-alexander.sverdlin@siemens.... Signed-off-by: Alexandre Belloni alexandre.belloni@bootlin.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/rtc/rtc-pcf85063.c | 19 ++++++++++++++++++- 1 file changed, 18 insertions(+), 1 deletion(-)
diff --git a/drivers/rtc/rtc-pcf85063.c b/drivers/rtc/rtc-pcf85063.c index 905986c616559..73848f764559b 100644 --- a/drivers/rtc/rtc-pcf85063.c +++ b/drivers/rtc/rtc-pcf85063.c @@ -35,6 +35,7 @@ #define PCF85063_REG_CTRL1_CAP_SEL BIT(0) #define PCF85063_REG_CTRL1_STOP BIT(5) #define PCF85063_REG_CTRL1_EXT_TEST BIT(7) +#define PCF85063_REG_CTRL1_SWR 0x58
#define PCF85063_REG_CTRL2 0x01 #define PCF85063_CTRL2_AF BIT(6) @@ -589,7 +590,7 @@ static int pcf85063_probe(struct i2c_client *client)
i2c_set_clientdata(client, pcf85063);
- err = regmap_read(pcf85063->regmap, PCF85063_REG_CTRL1, &tmp); + err = regmap_read(pcf85063->regmap, PCF85063_REG_SC, &tmp); if (err) { dev_err(&client->dev, "RTC chip is not present\n"); return err; @@ -599,6 +600,22 @@ static int pcf85063_probe(struct i2c_client *client) if (IS_ERR(pcf85063->rtc)) return PTR_ERR(pcf85063->rtc);
+ /* + * If a Power loss is detected, SW reset the device. + * From PCF85063A datasheet: + * There is a low probability that some devices will have corruption + * of the registers after the automatic power-on reset... + */ + if (tmp & PCF85063_REG_SC_OS) { + dev_warn(&client->dev, + "POR issue detected, sending a SW reset\n"); + err = regmap_write(pcf85063->regmap, PCF85063_REG_CTRL1, + PCF85063_REG_CTRL1_SWR); + if (err < 0) + dev_warn(&client->dev, + "SW reset failed, trying to continue\n"); + } + err = pcf85063_load_capacitance(pcf85063, client->dev.of_node, config->force_cap_7000 ? 7000 : 0); if (err < 0)