From: Erwan Le Ray erwan.leray@foss.st.com
[ Upstream commit 25a8e7611da5513b388165661b17173c26e12c04 ]
TX and RX FIFO thresholds may be cleared after suspend/resume, depending on the low power mode.
Those configurations (done in startup) are not effective for UART console, as: - the reference manual indicates that FIFOEN bit can only be written when the USART is disabled (UE=0) - a set_termios (where UE is set) is requested firstly for console enabling, before the startup.
Fixes: 84872dc448fe ("serial: stm32: add RX and TX FIFO flush") Signed-off-by: Erwan Le Ray erwan.leray@foss.st.com Link: https://lore.kernel.org/r/20210304162308.8984-5-erwan.leray@foss.st.com Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/tty/serial/stm32-usart.c | 23 +++++++++-------------- 1 file changed, 9 insertions(+), 14 deletions(-)
diff --git a/drivers/tty/serial/stm32-usart.c b/drivers/tty/serial/stm32-usart.c index eae54b8cf5e2..223cec70c57c 100644 --- a/drivers/tty/serial/stm32-usart.c +++ b/drivers/tty/serial/stm32-usart.c @@ -649,19 +649,8 @@ static int stm32_usart_startup(struct uart_port *port) if (ofs->rqr != UNDEF_REG) stm32_usart_set_bits(port, ofs->rqr, USART_RQR_RXFRQ);
- /* Tx and RX FIFO configuration */ - if (stm32_port->fifoen) { - val = readl_relaxed(port->membase + ofs->cr3); - val &= ~(USART_CR3_TXFTCFG_MASK | USART_CR3_RXFTCFG_MASK); - val |= USART_CR3_TXFTCFG_HALF << USART_CR3_TXFTCFG_SHIFT; - val |= USART_CR3_RXFTCFG_HALF << USART_CR3_RXFTCFG_SHIFT; - writel_relaxed(val, port->membase + ofs->cr3); - } - - /* RX FIFO enabling */ + /* RX enabling */ val = stm32_port->cr1_irq | USART_CR1_RE | BIT(cfg->uart_enable_bit); - if (stm32_port->fifoen) - val |= USART_CR1_FIFOEN; stm32_usart_set_bits(port, ofs->cr1, val);
return 0; @@ -770,9 +759,15 @@ static void stm32_usart_set_termios(struct uart_port *port, if (stm32_port->fifoen) cr1 |= USART_CR1_FIFOEN; cr2 = 0; + + /* Tx and RX FIFO configuration */ cr3 = readl_relaxed(port->membase + ofs->cr3); - cr3 &= USART_CR3_TXFTIE | USART_CR3_RXFTCFG_MASK | USART_CR3_RXFTIE - | USART_CR3_TXFTCFG_MASK; + cr3 &= USART_CR3_TXFTIE | USART_CR3_RXFTIE; + if (stm32_port->fifoen) { + cr3 &= ~(USART_CR3_TXFTCFG_MASK | USART_CR3_RXFTCFG_MASK); + cr3 |= USART_CR3_TXFTCFG_HALF << USART_CR3_TXFTCFG_SHIFT; + cr3 |= USART_CR3_RXFTCFG_HALF << USART_CR3_RXFTCFG_SHIFT; + }
if (cflag & CSTOPB) cr2 |= USART_CR2_STOP_2B;