5.0-stable review patch. If anyone has any objections, please let me know.
------------------
From: Mathias Nyman mathias.nyman@linux.intel.com
commit d92f2c59cc2cbca6bfb2cc54882b58ba76b15fd4 upstream.
Commit 2f31a67f01a8 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected") was intended to prevent ports that were still link training from being forced to U3 suspend state mid enumeration. This solved enumeration issues for devices with slow link training.
Turns out some devices are stuck in the link training/polling state, and thus that patch will prevent suspend completely for these devices. This is seen with USB3 card readers in some MacBooks.
Instead of preventing suspend, give some time to complete the link training. On successful training the port will end up as connected and enabled. If port instead is stuck in link training the bus suspend will continue suspending after 360ms (10 * 36ms) timeout (tPollingLFPSTimeout).
Original patch was sent to stable, this one should go there as well
Fixes: 2f31a67f01a8 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected") Cc: stable@vger.kernel.org Signed-off-by: Mathias Nyman mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org
--- drivers/usb/host/xhci-hub.c | 19 ++++++++++++------- drivers/usb/host/xhci.h | 8 ++++++++ 2 files changed, 20 insertions(+), 7 deletions(-)
--- a/drivers/usb/host/xhci-hub.c +++ b/drivers/usb/host/xhci-hub.c @@ -1545,20 +1545,25 @@ int xhci_bus_suspend(struct usb_hcd *hcd port_index = max_ports; while (port_index--) { u32 t1, t2; - + int retries = 10; +retry: t1 = readl(ports[port_index]->addr); t2 = xhci_port_state_to_neutral(t1); portsc_buf[port_index] = 0;
- /* Bail out if a USB3 port has a new device in link training */ - if ((hcd->speed >= HCD_USB3) && + /* + * Give a USB3 port in link training time to finish, but don't + * prevent suspend as port might be stuck + */ + if ((hcd->speed >= HCD_USB3) && retries-- && (t1 & PORT_PLS_MASK) == XDEV_POLLING) { - bus_state->bus_suspended = 0; spin_unlock_irqrestore(&xhci->lock, flags); - xhci_dbg(xhci, "Bus suspend bailout, port in polling\n"); - return -EBUSY; + msleep(XHCI_PORT_POLLING_LFPS_TIME); + spin_lock_irqsave(&xhci->lock, flags); + xhci_dbg(xhci, "port %d polling in bus suspend, waiting\n", + port_index); + goto retry; } - /* suspend ports in U0, or bail out for new connect changes */ if ((t1 & PORT_PE) && (t1 & PORT_PLS_MASK) == XDEV_U0) { if ((t1 & PORT_CSC) && wake_enabled) { --- a/drivers/usb/host/xhci.h +++ b/drivers/usb/host/xhci.h @@ -452,6 +452,14 @@ struct xhci_op_regs { */ #define XHCI_DEFAULT_BESL 4
+/* + * USB3 specification define a 360ms tPollingLFPSTiemout for USB3 ports + * to complete link training. usually link trainig completes much faster + * so check status 10 times with 36ms sleep in places we need to wait for + * polling to complete. + */ +#define XHCI_PORT_POLLING_LFPS_TIME 36 + /** * struct xhci_intr_reg - Interrupt Register Set * @irq_pending: IMAN - Interrupt Management Register. Used to enable