Existing genphy_loopback() is not applicable for Marvell PHY. Besides configuring bit-6 and bit-13 in Page 0 Register 0 (Copper Control Register), it is also required to configure same bits in Page 2 Register 21 (MAC Specific Control Register 2) according to speed of the loopback is operating.
Tested working on Marvell88E1510 PHY for all speeds (1000/100/10Mbps).
FIXME: Based on trial and error test, it seem 1G need to have delay between soft reset and loopback enablement.
Fixes: 014068dcb5b1 ("net: phy: genphy_loopback: add link speed configuration") Cc: stable@vger.kernel.org # 5.15.x Signed-off-by: Mohammad Athari Bin Ismail mohammad.athari.ismail@intel.com --- v2 changelog: - For loopback enabled, add bit-6 and bit-13 configuration in both Page 0 Register 0 and Page 2 Register 21. Commented by Heiner Kallweit hkallweit1@gmail.com. - For loopback disabled, follow genphy_loopback() implementation. --- drivers/net/phy/marvell.c | 46 ++++++++++++++++++++++++++++++++++++++- 1 file changed, 45 insertions(+), 1 deletion(-)
diff --git a/drivers/net/phy/marvell.c b/drivers/net/phy/marvell.c index 4fcfca4e1702..51ca2cc05e10 100644 --- a/drivers/net/phy/marvell.c +++ b/drivers/net/phy/marvell.c @@ -189,6 +189,8 @@ #define MII_88E1510_GEN_CTRL_REG_1_MODE_RGMII_SGMII 0x4 #define MII_88E1510_GEN_CTRL_REG_1_RESET 0x8000 /* Soft reset */
+#define MII_88E1510_MSCR_2 0x15 + #define MII_VCT5_TX_RX_MDI0_COUPLING 0x10 #define MII_VCT5_TX_RX_MDI1_COUPLING 0x11 #define MII_VCT5_TX_RX_MDI2_COUPLING 0x12 @@ -1932,6 +1934,48 @@ static void marvell_get_stats(struct phy_device *phydev, data[i] = marvell_get_stat(phydev, i); }
+static int marvell_loopback(struct phy_device *phydev, bool enable) +{ + if (enable) { + u16 bmcr_ctl = 0, mscr2_ctl = 0; + + if (phydev->speed == SPEED_1000) + bmcr_ctl = BMCR_SPEED1000; + else if (phydev->speed == SPEED_100) + bmcr_ctl = BMCR_SPEED100; + + if (phydev->duplex == DUPLEX_FULL) + bmcr_ctl |= BMCR_FULLDPLX; + + phy_modify(phydev, MII_BMCR, ~0, bmcr_ctl); + + if (phydev->speed == SPEED_1000) + mscr2_ctl = BMCR_SPEED1000; + else if (phydev->speed == SPEED_100) + mscr2_ctl = BMCR_SPEED100; + + phy_modify_paged(phydev, MII_MARVELL_MSCR_PAGE, + MII_88E1510_MSCR_2, BMCR_SPEED1000 | + BMCR_SPEED100, mscr2_ctl); + + /* Need soft reset to have speed configuration takes effect */ + genphy_soft_reset(phydev); + + /* FIXME: Based on trial and error test, it seem 1G need to have + * delay between soft reset and loopback enablement. + */ + if (phydev->speed == SPEED_1000) + msleep(1000); + + return phy_modify(phydev, MII_BMCR, BMCR_LOOPBACK, + BMCR_LOOPBACK); + } else { + phy_modify(phydev, MII_BMCR, BMCR_LOOPBACK, 0); + + return phy_config_aneg(phydev); + } +} + static int marvell_vct5_wait_complete(struct phy_device *phydev) { int i; @@ -3078,7 +3122,7 @@ static struct phy_driver marvell_drivers[] = { .get_sset_count = marvell_get_sset_count, .get_strings = marvell_get_strings, .get_stats = marvell_get_stats, - .set_loopback = genphy_loopback, + .set_loopback = marvell_loopback, .get_tunable = m88e1011_get_tunable, .set_tunable = m88e1011_set_tunable, .cable_test_start = marvell_vct7_cable_test_start,