6.1-stable review patch. If anyone has any objections, please let me know.
------------------
From: Peng Fan peng.fan@nxp.com
[ Upstream commit ff4279618f0aec350b0fb41b2b35841324fbd96e ]
To i.MX93 which features dual Cortex-A55 cores and DSU, when using writel_relaxed to write value to PLL registers, the value might be buffered. To make sure the value has been written into the hardware, using readl to read back the register could achieve the goal.
current PLL power up flow can be simplified as below: 1. writel_relaxed to set the PLL POWERUP bit; 2. readl_poll_timeout to check the PLL lock bit: a). timeout = ktime_add_us(ktime_get(), timeout_us); b). readl the pll the lock reg; c). check if the pll lock bit ready d). check if timeout
But in some corner cases, both the write in step 1 and read in step 2 will be blocked by other bus transaction in the SoC for a long time, saying the value into real hardware is just before step b). That means the timeout counting has begins for quite sometime since step a), but value still not written into real hardware until bus released just at a point before step b).
Then there maybe chances that the pll lock bit is not ready when readl done but the timeout happens. readl_poll_timeout will err return due to timeout. To avoid such unexpected failure, read back the reg to make sure the write has been done in HW reg.
So use readl after writel_relaxed to fix the issue.
Since we are here, to avoid udelay to run before writel_relaxed, use readl before udelay.
Fixes: 1b26cb8a77a4 ("clk: imx: support fracn gppll") Co-developed-by: Jacky Bai ping.bai@nxp.com Signed-off-by: Jacky Bai ping.bai@nxp.com Signed-off-by: Peng Fan peng.fan@nxp.com Reviewed-by: Abel Vesa abel.vesa@linaro.org Link: https://lore.kernel.org/r/20241027-imx-clk-v1-v3-3-89152574d1d7@nxp.com Signed-off-by: Abel Vesa abel.vesa@linaro.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/clk/imx/clk-fracn-gppll.c | 4 ++++ 1 file changed, 4 insertions(+)
diff --git a/drivers/clk/imx/clk-fracn-gppll.c b/drivers/clk/imx/clk-fracn-gppll.c index 281fc62ecd3d5..5f2296bb67a65 100644 --- a/drivers/clk/imx/clk-fracn-gppll.c +++ b/drivers/clk/imx/clk-fracn-gppll.c @@ -250,9 +250,11 @@ static int clk_fracn_gppll_set_rate(struct clk_hw *hw, unsigned long drate, pll_div = FIELD_PREP(PLL_RDIV_MASK, rate->rdiv) | rate->odiv | FIELD_PREP(PLL_MFI_MASK, rate->mfi); writel_relaxed(pll_div, pll->base + PLL_DIV); + readl(pll->base + PLL_DIV); if (pll->flags & CLK_FRACN_GPPLL_FRACN) { writel_relaxed(rate->mfd, pll->base + PLL_DENOMINATOR); writel_relaxed(FIELD_PREP(PLL_MFN_MASK, rate->mfn), pll->base + PLL_NUMERATOR); + readl(pll->base + PLL_NUMERATOR); }
/* Wait for 5us according to fracn mode pll doc */ @@ -261,6 +263,7 @@ static int clk_fracn_gppll_set_rate(struct clk_hw *hw, unsigned long drate, /* Enable Powerup */ tmp |= POWERUP_MASK; writel_relaxed(tmp, pll->base + PLL_CTRL); + readl(pll->base + PLL_CTRL);
/* Wait Lock */ ret = clk_fracn_gppll_wait_lock(pll); @@ -298,6 +301,7 @@ static int clk_fracn_gppll_prepare(struct clk_hw *hw)
val |= POWERUP_MASK; writel_relaxed(val, pll->base + PLL_CTRL); + readl(pll->base + PLL_CTRL);
ret = clk_fracn_gppll_wait_lock(pll); if (ret)