From: Lukasz Czechowski lukasz.czechowski@thaumatec.com
Currently, the onboard Cypress CYUSB3304 USB hub is not defined in the device tree, and hub reset pin is provided as vcc5v0_host regulator to usb phy. This causes instability issues, as a result of improper reset duration.
The fixed regulator device requests the GPIO during probe in its inactive state (except if regulator-boot-on property is set, in which case it is requested in the active state). Considering gpio is GPIO_ACTIVE_LOW for Puma, it means it’s driving it high. Then the regulator gets enabled (because regulator-always-on property), which drives it to its active state, meaning driving it low.
The Cypress CYUSB3304 USB hub actually requires the reset to be asserted for at least 5 ms, which we cannot guarantee right now since there's no delay in the current config, meaning the hub may sometimes work or not. We could add delay as offered by fixed-regulator but let's rather fix this by using the proper way to model onboard USB hubs.
Define hub_2_0 and hub_3_0 nodes, as the onboard Cypress hub consist of two 'logical' hubs, for USB2.0 and USB3.0. Use the 'reset-gpios' property of hub to assign reset pin instead of using regulator. Rename the vcc5v0_host regulator to cy3304_reset to be more meaningful. Pin is configured to output-high by default, which sets the hub in reset state during pin controller initialization. This allows to avoid double enumeration of devices in case the bootloader has setup the USB hub before the kernel. The vdd-supply and vdd2-supply properties in hub nodes are added to provide correct dt-bindings, although power supplies are always enabled based on HW design.
Fixes: 2c66fc34e945 ("arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM") Cc: stable@vger.kernel.org # 6.6 Cc: stable@vger.kernel.org # Backport of the patch in this series fixing product ID in onboard_dev_id_table in drivers/usb/misc/onboard_usb_dev.c driver Signed-off-by: Lukasz Czechowski lukasz.czechowski@thaumatec.com Link: https://lore.kernel.org/r/20250425-onboard_usb_dev-v2-3-4a76a474a010@thaumat... Signed-off-by: Heiko Stuebner heiko@sntech.de
[ upstream commit: d7cc532df95f7f159e40595440e4e4b99481457b ]
(cherry picked from commit 0fe42d171081426ab119ca5c0eb130e5f3a9a805) --- dts/upstream/src/arm64/rockchip/rk3399-puma.dtsi | 40 +++++++++++++++--------- 1 file changed, 26 insertions(+), 14 deletions(-)
diff --git a/dts/upstream/src/arm64/rockchip/rk3399-puma.dtsi b/dts/upstream/src/arm64/rockchip/rk3399-puma.dtsi index e00fbaa8acc1685af46495c0dfc9bdac7e6e991c..314d9dfdba5732c574283271fdb1e8f8ed5405ca 100644 --- a/dts/upstream/src/arm64/rockchip/rk3399-puma.dtsi +++ b/dts/upstream/src/arm64/rockchip/rk3399-puma.dtsi @@ -60,16 +60,6 @@ vin-supply = <&vcc5v0_sys>; };
- vcc5v0_host: regulator-vcc5v0-host { - compatible = "regulator-fixed"; - gpio = <&gpio4 RK_PA3 GPIO_ACTIVE_LOW>; - pinctrl-names = "default"; - pinctrl-0 = <&vcc5v0_host_en>; - regulator-name = "vcc5v0_host"; - regulator-always-on; - vin-supply = <&vcc5v0_sys>; - }; - vcc5v0_sys: regulator-vcc5v0-sys { compatible = "regulator-fixed"; regulator-name = "vcc5v0_sys"; @@ -527,10 +517,10 @@ }; };
- usb2 { - vcc5v0_host_en: vcc5v0-host-en { + usb { + cy3304_reset: cy3304-reset { rockchip,pins = - <4 RK_PA3 RK_FUNC_GPIO &pcfg_pull_none>; + <4 RK_PA3 RK_FUNC_GPIO &pcfg_output_high>; }; };
@@ -597,7 +587,6 @@ };
u2phy1_host: host-port { - phy-supply = <&vcc5v0_host>; status = "okay"; }; }; @@ -609,6 +598,29 @@ &usbdrd_dwc3_1 { status = "okay"; dr_mode = "host"; + pinctrl-names = "default"; + pinctrl-0 = <&cy3304_reset>; + #address-cells = <1>; + #size-cells = <0>; + + hub_2_0: hub@1 { + compatible = "usb4b4,6502", "usb4b4,6506"; + reg = <1>; + peer-hub = <&hub_3_0>; + reset-gpios = <&gpio4 RK_PA3 GPIO_ACTIVE_HIGH>; + vdd-supply = <&vcc1v2_phy>; + vdd2-supply = <&vcc3v3_sys>; + + }; + + hub_3_0: hub@2 { + compatible = "usb4b4,6500", "usb4b4,6504"; + reg = <2>; + peer-hub = <&hub_2_0>; + reset-gpios = <&gpio4 RK_PA3 GPIO_ACTIVE_HIGH>; + vdd-supply = <&vcc1v2_phy>; + vdd2-supply = <&vcc3v3_sys>; + }; };
&usb_host1_ehci {