6.6-stable review patch. If anyone has any objections, please let me know.
------------------
From: Hui Wang hui.wang@canonical.com
[ Upstream commit bfd546a552e140b0a4c8a21527c39d6d21addb28 ]
The commit 861e8086029e ("e1000e: move force SMBUS from enable ulp function to avoid PHY loss issue") introduces a regression on PCH_MTP_I219_LM18 (PCIID: 0x8086550A). Without the referred commit, the ethernet works well after suspend and resume, but after applying the commit, the ethernet couldn't work anymore after the resume and the dmesg shows that the NIC link changes to 10Mbps (1000Mbps originally):
[ 43.305084] e1000e 0000:00:1f.6 enp0s31f6: NIC Link is Up 10 Mbps Full Duplex, Flow Control: Rx/Tx
Without the commit, the force SMBUS code will not be executed if "return 0" or "goto out" is executed in the enable_ulp(), and in my case, the "goto out" is executed since FWSM_FW_VALID is set. But after applying the commit, the force SMBUS code will be ran unconditionally.
Here move the force SMBUS code back to enable_ulp() and put it immediately ahead of hw->phy.ops.release(hw), this could allow the longest settling time as possible for interface in this function and doesn't change the original code logic.
The issue was found on a Lenovo laptop with the ethernet hw as below: 00:1f.6 Ethernet controller [0200]: Intel Corporation Device [8086:550a] (rev 20).
And this patch is verified (cable plug and unplug, system suspend and resume) on Lenovo laptops with ethernet hw: [8086:550a], [8086:550b], [8086:15bb], [8086:15be], [8086:1a1f], [8086:1a1c] and [8086:0dc7].
Fixes: 861e8086029e ("e1000e: move force SMBUS from enable ulp function to avoid PHY loss issue") Signed-off-by: Hui Wang hui.wang@canonical.com Acked-by: Vitaly Lifshits vitaly.lifshits@intel.com Tested-by: Naama Meir naamax.meir@linux.intel.com Reviewed-by: Simon Horman horms@kernel.org Reviewed-by: Paul Menzel pmenzel@molgen.mpg.de Signed-off-by: Tony Nguyen anthony.l.nguyen@intel.com Tested-by: Zhang Rui rui.zhang@intel.com Signed-off-by: Jacob Keller jacob.e.keller@intel.com Link: https://lore.kernel.org/r/20240528-net-2024-05-28-intel-net-fixes-v1-1-dc859... Signed-off-by: Jakub Kicinski kuba@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/net/ethernet/intel/e1000e/ich8lan.c | 22 +++++++++++++++++++++ drivers/net/ethernet/intel/e1000e/netdev.c | 18 ----------------- 2 files changed, 22 insertions(+), 18 deletions(-)
diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c index f9e94be36e97f..2e98a2a0bead9 100644 --- a/drivers/net/ethernet/intel/e1000e/ich8lan.c +++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c @@ -1225,6 +1225,28 @@ s32 e1000_enable_ulp_lpt_lp(struct e1000_hw *hw, bool to_sx) }
release: + /* Switching PHY interface always returns MDI error + * so disable retry mechanism to avoid wasting time + */ + e1000e_disable_phy_retry(hw); + + /* Force SMBus mode in PHY */ + ret_val = e1000_read_phy_reg_hv_locked(hw, CV_SMB_CTRL, &phy_reg); + if (ret_val) { + e1000e_enable_phy_retry(hw); + hw->phy.ops.release(hw); + goto out; + } + phy_reg |= CV_SMB_CTRL_FORCE_SMBUS; + e1000_write_phy_reg_hv_locked(hw, CV_SMB_CTRL, phy_reg); + + e1000e_enable_phy_retry(hw); + + /* Force SMBus mode in MAC */ + mac_reg = er32(CTRL_EXT); + mac_reg |= E1000_CTRL_EXT_FORCE_SMBUS; + ew32(CTRL_EXT, mac_reg); + hw->phy.ops.release(hw); out: if (ret_val) diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c index d377a286c0e1b..06d109063c8d8 100644 --- a/drivers/net/ethernet/intel/e1000e/netdev.c +++ b/drivers/net/ethernet/intel/e1000e/netdev.c @@ -6623,7 +6623,6 @@ static int __e1000_shutdown(struct pci_dev *pdev, bool runtime) struct e1000_hw *hw = &adapter->hw; u32 ctrl, ctrl_ext, rctl, status, wufc; int retval = 0; - u16 smb_ctrl;
/* Runtime suspend should only enable wakeup for link changes */ if (runtime) @@ -6701,23 +6700,6 @@ static int __e1000_shutdown(struct pci_dev *pdev, bool runtime) goto skip_phy_configurations; } } - - /* Force SMBUS to allow WOL */ - /* Switching PHY interface always returns MDI error - * so disable retry mechanism to avoid wasting time - */ - e1000e_disable_phy_retry(hw); - - e1e_rphy(hw, CV_SMB_CTRL, &smb_ctrl); - smb_ctrl |= CV_SMB_CTRL_FORCE_SMBUS; - e1e_wphy(hw, CV_SMB_CTRL, smb_ctrl); - - e1000e_enable_phy_retry(hw); - - /* Force SMBus mode in MAC */ - ctrl_ext = er32(CTRL_EXT); - ctrl_ext |= E1000_CTRL_EXT_FORCE_SMBUS; - ew32(CTRL_EXT, ctrl_ext); }
/* Ensure that the appropriate bits are set in LPI_CTRL