From: Russell King (Oracle) rmk+kernel@armlinux.org.uk
[ Upstream commit 4e4f325a0a55907b14f579e6b1a38c53755e3de2 ]
The four RGMII interface modes take care of the required RGMII delay configuration at the PHY and should not be limited by the network MAC driver. Sadly, gemini was only permitting RGMII mode with no delays, which would require the required delay to be inserted via PCB tracking or by the MAC.
However, there are designs that require the PHY to add the delay, which is impossible without Gemini permitting the other three PHY interface modes. Fix the driver to allow these.
Signed-off-by: Russell King (Oracle) rmk+kernel@armlinux.org.uk Reviewed-by: Linus Walleij linus.walleij@linaro.org Tested-by: Corentin Labbe clabbe.montjoie@gmail.com Link: https://lore.kernel.org/r/E1n4mpT-002PLd-Ha@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski kuba@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/net/ethernet/cortina/gemini.c | 9 ++++++--- 1 file changed, 6 insertions(+), 3 deletions(-)
diff --git a/drivers/net/ethernet/cortina/gemini.c b/drivers/net/ethernet/cortina/gemini.c index 6e745ca4c4333..012ca11a38cc1 100644 --- a/drivers/net/ethernet/cortina/gemini.c +++ b/drivers/net/ethernet/cortina/gemini.c @@ -305,21 +305,21 @@ static void gmac_speed_set(struct net_device *netdev) switch (phydev->speed) { case 1000: status.bits.speed = GMAC_SPEED_1000; - if (phydev->interface == PHY_INTERFACE_MODE_RGMII) + if (phy_interface_mode_is_rgmii(phydev->interface)) status.bits.mii_rmii = GMAC_PHY_RGMII_1000; netdev_dbg(netdev, "connect %s to RGMII @ 1Gbit\n", phydev_name(phydev)); break; case 100: status.bits.speed = GMAC_SPEED_100; - if (phydev->interface == PHY_INTERFACE_MODE_RGMII) + if (phy_interface_mode_is_rgmii(phydev->interface)) status.bits.mii_rmii = GMAC_PHY_RGMII_100_10; netdev_dbg(netdev, "connect %s to RGMII @ 100 Mbit\n", phydev_name(phydev)); break; case 10: status.bits.speed = GMAC_SPEED_10; - if (phydev->interface == PHY_INTERFACE_MODE_RGMII) + if (phy_interface_mode_is_rgmii(phydev->interface)) status.bits.mii_rmii = GMAC_PHY_RGMII_100_10; netdev_dbg(netdev, "connect %s to RGMII @ 10 Mbit\n", phydev_name(phydev)); @@ -389,6 +389,9 @@ static int gmac_setup_phy(struct net_device *netdev) status.bits.mii_rmii = GMAC_PHY_GMII; break; case PHY_INTERFACE_MODE_RGMII: + case PHY_INTERFACE_MODE_RGMII_ID: + case PHY_INTERFACE_MODE_RGMII_TXID: + case PHY_INTERFACE_MODE_RGMII_RXID: netdev_dbg(netdev, "RGMII: set GMAC0 and GMAC1 to MII/RGMII mode\n"); status.bits.mii_rmii = GMAC_PHY_RGMII_100_10;