From: Xiaolei Li xiaolei.li@mediatek.com
commit e1884ffddacc0424d7e785e6f8087bd12f7196db upstream.
At present, the flow of calculating AC timing of read/write cycle in SDR mode is that: At first, calculate high hold time which is valid for both read and write cycle using the max value between tREH_min and tWH_min. Secondly, calculate WE# pulse width using tWP_min. Thridly, calculate RE# pulse width using the bigger one between tREA_max and tRP_min.
But NAND SPEC shows that Controller should also meet write/read cycle time. That is write cycle time should be more than tWC_min and read cycle should be more than tRC_min. Obviously, we do not achieve that now.
This patch corrects the low level time calculation to meet minimum read/write cycle time required. After getting the high hold time, WE# low level time will be promised to meet tWP_min and tWC_min requirement, and RE# low level time will be promised to meet tREA_max, tRP_min and tRC_min requirement.
Fixes: edfee3619c49 ("mtd: nand: mtk: add ->setup_data_interface() hook") Cc: stable@vger.kernel.org # v4.17+ Signed-off-by: Xiaolei Li xiaolei.li@mediatek.com Reviewed-by: Miquel Raynal miquel.raynal@bootlin.com Signed-off-by: Miquel Raynal miquel.raynal@bootlin.com Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org
--- drivers/mtd/nand/raw/mtk_nand.c | 24 +++++++++++++++++++++--- 1 file changed, 21 insertions(+), 3 deletions(-)
--- a/drivers/mtd/nand/raw/mtk_nand.c +++ b/drivers/mtd/nand/raw/mtk_nand.c @@ -508,7 +508,8 @@ static int mtk_nfc_setup_data_interface( { struct mtk_nfc *nfc = nand_get_controller_data(chip); const struct nand_sdr_timings *timings; - u32 rate, tpoecs, tprecs, tc2r, tw2r, twh, twst, trlt; + u32 rate, tpoecs, tprecs, tc2r, tw2r, twh, twst = 0, trlt = 0; + u32 thold;
timings = nand_get_sdr_timings(conf); if (IS_ERR(timings)) @@ -544,11 +545,28 @@ static int mtk_nfc_setup_data_interface( twh = DIV_ROUND_UP(twh * rate, 1000000) - 1; twh &= 0xf;
- twst = timings->tWP_min / 1000; + /* Calculate real WE#/RE# hold time in nanosecond */ + thold = (twh + 1) * 1000000 / rate; + /* nanosecond to picosecond */ + thold *= 1000; + + /* + * WE# low level time should be expaned to meet WE# pulse time + * and WE# cycle time at the same time. + */ + if (thold < timings->tWC_min) + twst = timings->tWC_min - thold; + twst = max(timings->tWP_min, twst) / 1000; twst = DIV_ROUND_UP(twst * rate, 1000000) - 1; twst &= 0xf;
- trlt = max(timings->tREA_max, timings->tRP_min) / 1000; + /* + * RE# low level time should be expaned to meet RE# pulse time, + * RE# access time and RE# cycle time at the same time. + */ + if (thold < timings->tRC_min) + trlt = timings->tRC_min - thold; + trlt = max3(trlt, timings->tREA_max, timings->tRP_min) / 1000; trlt = DIV_ROUND_UP(trlt * rate, 1000000) - 1; trlt &= 0xf;