From: Jai Luthra j-luthra@ti.com
[ Upstream commit decea0a98b7ac04536c7d659f74783e8d67a06c0 ]
Move the register-based reset out of the init_setting[] and into the powerup_sequence function. The sensor is power cycled and reset using the gpio pins so the soft reset is not always necessary.
This also ensures that soft reset honors the timing sequence from the datasheet [1].
[1] https://cdn.sparkfun.com/datasheets/Sensors/LightImaging/OV5640_datasheet.pd...
Fixes: 19a81c1426c1 ("[media] add Omnivision OV5640 sensor driver") Reported-by: Nishanth Menon nm@ti.com Suggested-by: Jacopo Mondi jacopo.mondi@ideasonboard.com Signed-off-by: Jai Luthra j-luthra@ti.com Reviewed-by: Jacopo Mondi jacopo.mondi@ideasonaboard.com Signed-off-by: Sakari Ailus sakari.ailus@linux.intel.com Signed-off-by: Mauro Carvalho Chehab mchehab@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/media/i2c/ov5640.c | 34 ++++++++++++++++++++++++---------- 1 file changed, 24 insertions(+), 10 deletions(-)
diff --git a/drivers/media/i2c/ov5640.c b/drivers/media/i2c/ov5640.c index 3f6d715efa823..f31b096e018f2 100644 --- a/drivers/media/i2c/ov5640.c +++ b/drivers/media/i2c/ov5640.c @@ -50,6 +50,7 @@ #define OV5640_REG_SYS_CTRL0 0x3008 #define OV5640_REG_SYS_CTRL0_SW_PWDN 0x42 #define OV5640_REG_SYS_CTRL0_SW_PWUP 0x02 +#define OV5640_REG_SYS_CTRL0_SW_RST 0x82 #define OV5640_REG_CHIP_ID 0x300a #define OV5640_REG_IO_MIPI_CTRL00 0x300e #define OV5640_REG_PAD_OUTPUT_ENABLE01 0x3017 @@ -532,7 +533,7 @@ static const struct v4l2_mbus_framefmt ov5640_default_fmt = { };
static const struct reg_value ov5640_init_setting[] = { - {0x3103, 0x11, 0, 0}, {0x3008, 0x82, 0, 5}, {0x3008, 0x42, 0, 0}, + {0x3103, 0x11, 0, 0}, {0x3103, 0x03, 0, 0}, {0x3630, 0x36, 0, 0}, {0x3631, 0x0e, 0, 0}, {0x3632, 0xe2, 0, 0}, {0x3633, 0x12, 0, 0}, {0x3621, 0xe0, 0, 0}, {0x3704, 0xa0, 0, 0}, {0x3703, 0x5a, 0, 0}, @@ -2429,19 +2430,32 @@ static void ov5640_reset(struct ov5640_dev *sensor) if (!sensor->reset_gpio) return;
- gpiod_set_value_cansleep(sensor->reset_gpio, 0); + if (sensor->pwdn_gpio) { + gpiod_set_value_cansleep(sensor->reset_gpio, 0);
- /* camera power cycle */ - ov5640_power(sensor, false); - usleep_range(5000, 10000); - ov5640_power(sensor, true); - usleep_range(5000, 10000); + /* camera power cycle */ + ov5640_power(sensor, false); + usleep_range(5000, 10000); + ov5640_power(sensor, true); + usleep_range(5000, 10000);
- gpiod_set_value_cansleep(sensor->reset_gpio, 1); - usleep_range(1000, 2000); + gpiod_set_value_cansleep(sensor->reset_gpio, 1); + usleep_range(1000, 2000);
- gpiod_set_value_cansleep(sensor->reset_gpio, 0); + gpiod_set_value_cansleep(sensor->reset_gpio, 0); + } else { + /* software reset */ + ov5640_write_reg(sensor, OV5640_REG_SYS_CTRL0, + OV5640_REG_SYS_CTRL0_SW_RST); + } usleep_range(20000, 25000); + + /* + * software standby: allows registers programming; + * exit at restore_mode() for CSI, s_stream(1) for DVP + */ + ov5640_write_reg(sensor, OV5640_REG_SYS_CTRL0, + OV5640_REG_SYS_CTRL0_SW_PWDN); }
static int ov5640_set_power_on(struct ov5640_dev *sensor)