From: Faiz Abbas faiz_abbas@ti.com
[ Upstream commit fb59ee37cfe20d10d19568899d1458a58361246c ]
If UHS speed modes are enabled, a compatible SD card switches down to 1.8V during enumeration. If after this a software reboot/crash takes place and on-chip ROM tries to enumerate the SD card, the difference in IO voltages (host @ 3.3V and card @ 1.8V) may end up damaging the card.
The fix for this is to have support for power cycling the card in hardware (with a PORz/soft-reset line causing a power cycle of the card). Because the beaglebone X15 (rev A,B and C), am57xx-idks and am57xx-evms don't have this capability, disable voltage switching for these boards.
The major effect of this is that the maximum supported speed mode is now high speed(50 MHz) down from SDR104(200 MHz).
commit 88a748419b84 ("ARM: dts: am57xx-idk: Remove support for voltage switching for SD card") did this only for idk boards. Do it for all affected boards.
Signed-off-by: Faiz Abbas faiz_abbas@ti.com Signed-off-by: Tony Lindgren tony@atomide.com Signed-off-by: Sasha Levin sashal@kernel.org --- arch/arm/boot/dts/am571x-idk.dts | 7 +------ arch/arm/boot/dts/am572x-idk.dts | 7 +------ arch/arm/boot/dts/am574x-idk.dts | 7 +------ arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi | 1 + arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts | 7 +------ arch/arm/boot/dts/am57xx-beagle-x15-revc.dts | 7 +------ 6 files changed, 6 insertions(+), 30 deletions(-)
diff --git a/arch/arm/boot/dts/am571x-idk.dts b/arch/arm/boot/dts/am571x-idk.dts index 1d5e99964bbf8..0aaacea1d887b 100644 --- a/arch/arm/boot/dts/am571x-idk.dts +++ b/arch/arm/boot/dts/am571x-idk.dts @@ -175,14 +175,9 @@ };
&mmc1 { - pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104"; + pinctrl-names = "default", "hs"; pinctrl-0 = <&mmc1_pins_default_no_clk_pu>; pinctrl-1 = <&mmc1_pins_hs>; - pinctrl-2 = <&mmc1_pins_sdr12>; - pinctrl-3 = <&mmc1_pins_sdr25>; - pinctrl-4 = <&mmc1_pins_sdr50>; - pinctrl-5 = <&mmc1_pins_ddr50_rev20 &mmc1_iodelay_ddr50_conf>; - pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev20_conf>; };
&mmc2 { diff --git a/arch/arm/boot/dts/am572x-idk.dts b/arch/arm/boot/dts/am572x-idk.dts index c65d7f6d3b5a6..ea1c119feaa57 100644 --- a/arch/arm/boot/dts/am572x-idk.dts +++ b/arch/arm/boot/dts/am572x-idk.dts @@ -16,14 +16,9 @@ };
&mmc1 { - pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104"; + pinctrl-names = "default", "hs"; pinctrl-0 = <&mmc1_pins_default_no_clk_pu>; pinctrl-1 = <&mmc1_pins_hs>; - pinctrl-2 = <&mmc1_pins_sdr12>; - pinctrl-3 = <&mmc1_pins_sdr25>; - pinctrl-4 = <&mmc1_pins_sdr50>; - pinctrl-5 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr_rev20_conf>; - pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev20_conf>; };
&mmc2 { diff --git a/arch/arm/boot/dts/am574x-idk.dts b/arch/arm/boot/dts/am574x-idk.dts index dc5141c35610e..7935d70874ce2 100644 --- a/arch/arm/boot/dts/am574x-idk.dts +++ b/arch/arm/boot/dts/am574x-idk.dts @@ -24,14 +24,9 @@ };
&mmc1 { - pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104"; + pinctrl-names = "default", "hs"; pinctrl-0 = <&mmc1_pins_default_no_clk_pu>; pinctrl-1 = <&mmc1_pins_hs>; - pinctrl-2 = <&mmc1_pins_default>; - pinctrl-3 = <&mmc1_pins_hs>; - pinctrl-4 = <&mmc1_pins_sdr50>; - pinctrl-5 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr_conf>; - pinctrl-6 = <&mmc1_pins_ddr50 &mmc1_iodelay_sdr104_conf>; };
&mmc2 { diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi index d02f5fa61e5f5..d50de7a6ea6c5 100644 --- a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi +++ b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi @@ -430,6 +430,7 @@
bus-width = <4>; cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>; /* gpio 219 */ + no-1-8-v; };
&mmc2 { diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts b/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts index a374b5cd6db0e..7b113b52c3fb6 100644 --- a/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts +++ b/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts @@ -16,14 +16,9 @@ };
&mmc1 { - pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104"; + pinctrl-names = "default", "hs"; pinctrl-0 = <&mmc1_pins_default>; pinctrl-1 = <&mmc1_pins_hs>; - pinctrl-2 = <&mmc1_pins_sdr12>; - pinctrl-3 = <&mmc1_pins_sdr25>; - pinctrl-4 = <&mmc1_pins_sdr50>; - pinctrl-5 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr_rev11_conf>; - pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev11_conf>; vmmc-supply = <&vdd_3v3>; vqmmc-supply = <&ldo1_reg>; }; diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-revc.dts b/arch/arm/boot/dts/am57xx-beagle-x15-revc.dts index 4badd2144db9a..30c500b15b219 100644 --- a/arch/arm/boot/dts/am57xx-beagle-x15-revc.dts +++ b/arch/arm/boot/dts/am57xx-beagle-x15-revc.dts @@ -16,14 +16,9 @@ };
&mmc1 { - pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104"; + pinctrl-names = "default", "hs"; pinctrl-0 = <&mmc1_pins_default>; pinctrl-1 = <&mmc1_pins_hs>; - pinctrl-2 = <&mmc1_pins_sdr12>; - pinctrl-3 = <&mmc1_pins_sdr25>; - pinctrl-4 = <&mmc1_pins_sdr50>; - pinctrl-5 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr_rev20_conf>; - pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev20_conf>; vmmc-supply = <&vdd_3v3>; vqmmc-supply = <&ldo1_reg>; };