The patch below does not apply to the 4.9-stable tree.
If someone wants it applied there, or to any other stable or longterm
tree, then please email the backport, including the original git commit
id to <stable(a)vger.kernel.org>.
thanks,
greg k-h
------------------ original commit in Linus's tree ------------------
>From 3f77f244d8ec28e3a0a81240ffac7d626390060c Mon Sep 17 00:00:00 2001
From: Martin Kaiser <martin(a)kaiser.cx>
Date: Mon, 18 Jun 2018 22:41:03 +0200
Subject: [PATCH] mtd: rawnand: mxc: set spare area size register explicitly
The v21 version of the NAND flash controller contains a Spare Area Size
Register (SPAS) at offset 0x10. Its setting defaults to the maximum
spare area size of 218 bytes. The size that is set in this register is
used by the controller when it calculates the ECC bytes internally in
hardware.
Usually, this register is updated from settings in the IIM fuses when
the system is booting from NAND flash. For other boot media, however,
the SPAS register remains at the default setting, which may not work for
the particular flash chip on the board. The same goes for flash chips
whose configuration cannot be set in the IIM fuses (e.g. chips with 2k
sector size and 128 bytes spare area size can't be configured in the IIM
fuses on imx25 systems).
Set the SPAS register explicitly during the preset operation. Derive the
register value from mtd->oobsize that was detected during probe by
decoding the flash chip's ID bytes.
While at it, rename the define for the spare area register's offset to
NFC_V21_RSLTSPARE_AREA. The register at offset 0x10 on v1 controllers is
different from the register on v21 controllers.
Fixes: d484018 ("mtd: mxc_nand: set NFC registers after reset")
Cc: stable(a)vger.kernel.org
Signed-off-by: Martin Kaiser <martin(a)kaiser.cx>
Reviewed-by: Sascha Hauer <s.hauer(a)pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal(a)bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon(a)bootlin.com>
diff --git a/drivers/mtd/nand/raw/mxc_nand.c b/drivers/mtd/nand/raw/mxc_nand.c
index 45786e707b7b..26cef218bb43 100644
--- a/drivers/mtd/nand/raw/mxc_nand.c
+++ b/drivers/mtd/nand/raw/mxc_nand.c
@@ -48,7 +48,7 @@
#define NFC_V1_V2_CONFIG (host->regs + 0x0a)
#define NFC_V1_V2_ECC_STATUS_RESULT (host->regs + 0x0c)
#define NFC_V1_V2_RSLTMAIN_AREA (host->regs + 0x0e)
-#define NFC_V1_V2_RSLTSPARE_AREA (host->regs + 0x10)
+#define NFC_V21_RSLTSPARE_AREA (host->regs + 0x10)
#define NFC_V1_V2_WRPROT (host->regs + 0x12)
#define NFC_V1_UNLOCKSTART_BLKADDR (host->regs + 0x14)
#define NFC_V1_UNLOCKEND_BLKADDR (host->regs + 0x16)
@@ -1274,6 +1274,9 @@ static void preset_v2(struct mtd_info *mtd)
writew(config1, NFC_V1_V2_CONFIG1);
/* preset operation */
+ /* spare area size in 16-bit half-words */
+ writew(mtd->oobsize / 2, NFC_V21_RSLTSPARE_AREA);
+
/* Unlock the internal RAM Buffer */
writew(0x2, NFC_V1_V2_CONFIG);
The patch below does not apply to the 4.14-stable tree.
If someone wants it applied there, or to any other stable or longterm
tree, then please email the backport, including the original git commit
id to <stable(a)vger.kernel.org>.
thanks,
greg k-h
------------------ original commit in Linus's tree ------------------
>From e9893e6fa932f42c90c4ac5849fa9aa0f0f00a34 Mon Sep 17 00:00:00 2001
From: Abhishek Sahu <absahu(a)codeaurora.org>
Date: Wed, 13 Jun 2018 14:32:36 +0530
Subject: [PATCH] mtd: rawnand: fix return value check for bad block status
Positive return value from read_oob() is making false BAD
blocks. For some of the NAND controllers, OOB bytes will be
protected with ECC and read_oob() will return number of bitflips.
If there is any bitflip in ECC protected OOB bytes for BAD block
status page, then that block is getting treated as BAD.
Fixes: c120e75e0e7d ("mtd: nand: use read_oob() instead of cmdfunc() for bad block check")
Cc: <stable(a)vger.kernel.org>
Signed-off-by: Abhishek Sahu <absahu(a)codeaurora.org>
Reviewed-by: Miquel Raynal <miquel.raynal(a)bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon(a)bootlin.com>
diff --git a/drivers/mtd/nand/raw/nand_base.c b/drivers/mtd/nand/raw/nand_base.c
index 10c4f9919850..b01d15ec4c56 100644
--- a/drivers/mtd/nand/raw/nand_base.c
+++ b/drivers/mtd/nand/raw/nand_base.c
@@ -440,7 +440,7 @@ static int nand_block_bad(struct mtd_info *mtd, loff_t ofs)
for (; page < page_end; page++) {
res = chip->ecc.read_oob(mtd, chip, page);
- if (res)
+ if (res < 0)
return res;
bad = chip->oob_poi[chip->badblockpos];
The patch below does not apply to the 4.17-stable tree.
If someone wants it applied there, or to any other stable or longterm
tree, then please email the backport, including the original git commit
id to <stable(a)vger.kernel.org>.
thanks,
greg k-h
------------------ original commit in Linus's tree ------------------
>From 79ca484b613041ca223f74b34608bb6f5221724b Mon Sep 17 00:00:00 2001
From: Tokunori Ikegami <ikegami(a)allied-telesis.co.jp>
Date: Wed, 30 May 2018 18:32:29 +0900
Subject: [PATCH] mtd: cfi_cmdset_0002: Change erase functions to check chip
good only
Currently the functions use to check both chip ready and good.
But the chip ready is not enough to check the operation status.
So change this to check the chip good instead of this.
About the retry functions to make sure the error handling remain it.
Signed-off-by: Tokunori Ikegami <ikegami(a)allied-telesis.co.jp>
Reviewed-by: Joakim Tjernlund <Joakim.Tjernlund(a)infinera.com>
Cc: Chris Packham <chris.packham(a)alliedtelesis.co.nz>
Cc: Brian Norris <computersforpeace(a)gmail.com>
Cc: David Woodhouse <dwmw2(a)infradead.org>
Cc: Boris Brezillon <boris.brezillon(a)free-electrons.com>
Cc: Marek Vasut <marek.vasut(a)gmail.com>
Cc: Richard Weinberger <richard(a)nod.at>
Cc: Cyrille Pitchen <cyrille.pitchen(a)wedev4u.fr>
Cc: linux-mtd(a)lists.infradead.org
Cc: stable(a)vger.kernel.org
Signed-off-by: Boris Brezillon <boris.brezillon(a)bootlin.com>
diff --git a/drivers/mtd/chips/cfi_cmdset_0002.c b/drivers/mtd/chips/cfi_cmdset_0002.c
index 217db661943d..d8e3a737c62f 100644
--- a/drivers/mtd/chips/cfi_cmdset_0002.c
+++ b/drivers/mtd/chips/cfi_cmdset_0002.c
@@ -2294,12 +2294,13 @@ static int __xipram do_erase_chip(struct map_info *map, struct flchip *chip)
chip->erase_suspended = 0;
}
- if (chip_ready(map, adr))
+ if (chip_good(map, adr, map_word_ff(map)))
break;
if (time_after(jiffies, timeo)) {
printk(KERN_WARNING "MTD %s(): software timeout\n",
__func__);
+ ret = -EIO;
break;
}
@@ -2307,15 +2308,15 @@ static int __xipram do_erase_chip(struct map_info *map, struct flchip *chip)
UDELAY(map, chip, adr, 1000000/HZ);
}
/* Did we succeed? */
- if (!chip_good(map, adr, map_word_ff(map))) {
+ if (ret) {
/* reset on all failures. */
map_write(map, CMD(0xF0), chip->start);
/* FIXME - should have reset delay before continuing */
- if (++retry_cnt <= MAX_RETRIES)
+ if (++retry_cnt <= MAX_RETRIES) {
+ ret = 0;
goto retry;
-
- ret = -EIO;
+ }
}
chip->state = FL_READY;
@@ -2388,7 +2389,7 @@ static int __xipram do_erase_oneblock(struct map_info *map, struct flchip *chip,
chip->erase_suspended = 0;
}
- if (chip_ready(map, adr)) {
+ if (chip_good(map, adr, map_word_ff(map))) {
xip_enable(map, chip, adr);
break;
}
@@ -2397,6 +2398,7 @@ static int __xipram do_erase_oneblock(struct map_info *map, struct flchip *chip,
xip_enable(map, chip, adr);
printk(KERN_WARNING "MTD %s(): software timeout\n",
__func__);
+ ret = -EIO;
break;
}
@@ -2404,15 +2406,15 @@ static int __xipram do_erase_oneblock(struct map_info *map, struct flchip *chip,
UDELAY(map, chip, adr, 1000000/HZ);
}
/* Did we succeed? */
- if (!chip_good(map, adr, map_word_ff(map))) {
+ if (ret) {
/* reset on all failures. */
map_write(map, CMD(0xF0), chip->start);
/* FIXME - should have reset delay before continuing */
- if (++retry_cnt <= MAX_RETRIES)
+ if (++retry_cnt <= MAX_RETRIES) {
+ ret = 0;
goto retry;
-
- ret = -EIO;
+ }
}
chip->state = FL_READY;
The patch below does not apply to the 4.17-stable tree.
If someone wants it applied there, or to any other stable or longterm
tree, then please email the backport, including the original git commit
id to <stable(a)vger.kernel.org>.
thanks,
greg k-h
------------------ original commit in Linus's tree ------------------
>From 85a82e28b023de9b259a86824afbd6ba07bd6475 Mon Sep 17 00:00:00 2001
From: Tokunori Ikegami <ikegami(a)allied-telesis.co.jp>
Date: Wed, 30 May 2018 18:32:27 +0900
Subject: [PATCH] mtd: cfi_cmdset_0002: Change definition naming to retry write
operation
The definition can be used for other program and erase operations also.
So change the naming to MAX_RETRIES from MAX_WORD_RETRIES.
Signed-off-by: Tokunori Ikegami <ikegami(a)allied-telesis.co.jp>
Reviewed-by: Joakim Tjernlund <Joakim.Tjernlund(a)infinera.com>
Cc: Chris Packham <chris.packham(a)alliedtelesis.co.nz>
Cc: Brian Norris <computersforpeace(a)gmail.com>
Cc: David Woodhouse <dwmw2(a)infradead.org>
Cc: Boris Brezillon <boris.brezillon(a)free-electrons.com>
Cc: Marek Vasut <marek.vasut(a)gmail.com>
Cc: Richard Weinberger <richard(a)nod.at>
Cc: Cyrille Pitchen <cyrille.pitchen(a)wedev4u.fr>
Cc: linux-mtd(a)lists.infradead.org
Cc: stable(a)vger.kernel.org
Signed-off-by: Boris Brezillon <boris.brezillon(a)bootlin.com>
diff --git a/drivers/mtd/chips/cfi_cmdset_0002.c b/drivers/mtd/chips/cfi_cmdset_0002.c
index 75d2c16029fd..62ada405fe93 100644
--- a/drivers/mtd/chips/cfi_cmdset_0002.c
+++ b/drivers/mtd/chips/cfi_cmdset_0002.c
@@ -42,7 +42,7 @@
#define AMD_BOOTLOC_BUG
#define FORCE_WORD_WRITE 0
-#define MAX_WORD_RETRIES 3
+#define MAX_RETRIES 3
#define SST49LF004B 0x0060
#define SST49LF040B 0x0050
@@ -1646,7 +1646,7 @@ static int __xipram do_write_oneword(struct map_info *map, struct flchip *chip,
map_write(map, CMD(0xF0), chip->start);
/* FIXME - should have reset delay before continuing */
- if (++retry_cnt <= MAX_WORD_RETRIES)
+ if (++retry_cnt <= MAX_RETRIES)
goto retry;
ret = -EIO;
@@ -2105,7 +2105,7 @@ static int do_panic_write_oneword(struct map_info *map, struct flchip *chip,
map_write(map, CMD(0xF0), chip->start);
/* FIXME - should have reset delay before continuing */
- if (++retry_cnt <= MAX_WORD_RETRIES)
+ if (++retry_cnt <= MAX_RETRIES)
goto retry;
ret = -EIO;
The patch below does not apply to the 4.9-stable tree.
If someone wants it applied there, or to any other stable or longterm
tree, then please email the backport, including the original git commit
id to <stable(a)vger.kernel.org>.
thanks,
greg k-h
------------------ original commit in Linus's tree ------------------
>From 1bc0299d976e000ececc6acd76e33b4582646cb7 Mon Sep 17 00:00:00 2001
From: Mike Marciniszyn <mike.marciniszyn(a)intel.com>
Date: Thu, 31 May 2018 11:30:09 -0700
Subject: [PATCH] IB/hfi1: Fix user context tail allocation for DMA_RTAIL
The following code fails to allocate a buffer for the
tail address that the hardware DMAs into when the user
context DMA_RTAIL is set.
if (HFI1_CAP_KGET_MASK(rcd->flags, DMA_RTAIL)) {
rcd->rcvhdrtail_kvaddr = dma_zalloc_coherent(
&dd->pcidev->dev, PAGE_SIZE, &dma_hdrqtail,
gfp_flags);
if (!rcd->rcvhdrtail_kvaddr)
goto bail_free;
rcd->rcvhdrqtailaddr_dma = dma_hdrqtail;
}
So the rcvhdrtail_kvaddr would then be NULL.
The mmap logic fails to check for a NULL rcvhdrtail_kvaddr.
The fix is to test for both user and kernel DMA_TAIL options
during the allocation as well as testing for a NULL
rcvhdrtail_kvaddr during the mmap processing.
Additionally, all downstream testing of the capmask for DMA_RTAIL
have been eliminated in favor of testing rcvhdrtail_kvaddr.
Cc: <stable(a)vger.kernel.org> # 4.9.x
Reviewed-by: Michael J. Ruhl <michael.j.ruhl(a)intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn(a)intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro(a)intel.com>
Signed-off-by: Jason Gunthorpe <jgg(a)mellanox.com>
diff --git a/drivers/infiniband/hw/hfi1/chip.c b/drivers/infiniband/hw/hfi1/chip.c
index 68580cb2ae1e..f75080d63142 100644
--- a/drivers/infiniband/hw/hfi1/chip.c
+++ b/drivers/infiniband/hw/hfi1/chip.c
@@ -6841,7 +6841,7 @@ static void rxe_kernel_unfreeze(struct hfi1_devdata *dd)
}
rcvmask = HFI1_RCVCTRL_CTXT_ENB;
/* HFI1_RCVCTRL_TAILUPD_[ENB|DIS] needs to be set explicitly */
- rcvmask |= HFI1_CAP_KGET_MASK(rcd->flags, DMA_RTAIL) ?
+ rcvmask |= rcd->rcvhdrtail_kvaddr ?
HFI1_RCVCTRL_TAILUPD_ENB : HFI1_RCVCTRL_TAILUPD_DIS;
hfi1_rcvctrl(dd, rcvmask, rcd);
hfi1_rcd_put(rcd);
@@ -8367,7 +8367,7 @@ static inline int check_packet_present(struct hfi1_ctxtdata *rcd)
u32 tail;
int present;
- if (!HFI1_CAP_IS_KSET(DMA_RTAIL))
+ if (!rcd->rcvhdrtail_kvaddr)
present = (rcd->seq_cnt ==
rhf_rcv_seq(rhf_to_cpu(get_rhf_addr(rcd))));
else /* is RDMA rtail */
@@ -11843,7 +11843,7 @@ void hfi1_rcvctrl(struct hfi1_devdata *dd, unsigned int op,
/* reset the tail and hdr addresses, and sequence count */
write_kctxt_csr(dd, ctxt, RCV_HDR_ADDR,
rcd->rcvhdrq_dma);
- if (HFI1_CAP_KGET_MASK(rcd->flags, DMA_RTAIL))
+ if (rcd->rcvhdrtail_kvaddr)
write_kctxt_csr(dd, ctxt, RCV_HDR_TAIL_ADDR,
rcd->rcvhdrqtailaddr_dma);
rcd->seq_cnt = 1;
@@ -11923,7 +11923,7 @@ void hfi1_rcvctrl(struct hfi1_devdata *dd, unsigned int op,
rcvctrl |= RCV_CTXT_CTRL_INTR_AVAIL_SMASK;
if (op & HFI1_RCVCTRL_INTRAVAIL_DIS)
rcvctrl &= ~RCV_CTXT_CTRL_INTR_AVAIL_SMASK;
- if (op & HFI1_RCVCTRL_TAILUPD_ENB && rcd->rcvhdrqtailaddr_dma)
+ if ((op & HFI1_RCVCTRL_TAILUPD_ENB) && rcd->rcvhdrtail_kvaddr)
rcvctrl |= RCV_CTXT_CTRL_TAIL_UPD_SMASK;
if (op & HFI1_RCVCTRL_TAILUPD_DIS) {
/* See comment on RcvCtxtCtrl.TailUpd above */
diff --git a/drivers/infiniband/hw/hfi1/file_ops.c b/drivers/infiniband/hw/hfi1/file_ops.c
index c9d23c37a371..0fc4aa9455c3 100644
--- a/drivers/infiniband/hw/hfi1/file_ops.c
+++ b/drivers/infiniband/hw/hfi1/file_ops.c
@@ -505,7 +505,7 @@ static int hfi1_file_mmap(struct file *fp, struct vm_area_struct *vma)
ret = -EINVAL;
goto done;
}
- if (flags & VM_WRITE) {
+ if ((flags & VM_WRITE) || !uctxt->rcvhdrtail_kvaddr) {
ret = -EPERM;
goto done;
}
diff --git a/drivers/infiniband/hw/hfi1/init.c b/drivers/infiniband/hw/hfi1/init.c
index 3feecf926322..4a478ee0a79b 100644
--- a/drivers/infiniband/hw/hfi1/init.c
+++ b/drivers/infiniband/hw/hfi1/init.c
@@ -1853,7 +1853,6 @@ int hfi1_create_rcvhdrq(struct hfi1_devdata *dd, struct hfi1_ctxtdata *rcd)
u64 reg;
if (!rcd->rcvhdrq) {
- dma_addr_t dma_hdrqtail;
gfp_t gfp_flags;
/*
@@ -1878,13 +1877,13 @@ int hfi1_create_rcvhdrq(struct hfi1_devdata *dd, struct hfi1_ctxtdata *rcd)
goto bail;
}
- if (HFI1_CAP_KGET_MASK(rcd->flags, DMA_RTAIL)) {
+ if (HFI1_CAP_KGET_MASK(rcd->flags, DMA_RTAIL) ||
+ HFI1_CAP_UGET_MASK(rcd->flags, DMA_RTAIL)) {
rcd->rcvhdrtail_kvaddr = dma_zalloc_coherent(
- &dd->pcidev->dev, PAGE_SIZE, &dma_hdrqtail,
- gfp_flags);
+ &dd->pcidev->dev, PAGE_SIZE,
+ &rcd->rcvhdrqtailaddr_dma, gfp_flags);
if (!rcd->rcvhdrtail_kvaddr)
goto bail_free;
- rcd->rcvhdrqtailaddr_dma = dma_hdrqtail;
}
rcd->rcvhdrq_size = amt;
The patch below does not apply to the 4.9-stable tree.
If someone wants it applied there, or to any other stable or longterm
tree, then please email the backport, including the original git commit
id to <stable(a)vger.kernel.org>.
thanks,
greg k-h
------------------ original commit in Linus's tree ------------------
>From a93a0a31111231bb1949f4a83b17238f0fa32d6a Mon Sep 17 00:00:00 2001
From: "Michael J. Ruhl" <michael.j.ruhl(a)intel.com>
Date: Wed, 2 May 2018 06:43:07 -0700
Subject: [PATCH] IB/hfi1: Reorder incorrect send context disable
User send context integrity bits are cleared before the context is
disabled. If the send context is still processing data, any packets
that need those integrity bits will cause an error and halt the send
context.
During the disable handling, the driver waits for the context to drain.
If the context is halted, the driver will eventually timeout because
the context won't drain and then incorrectly bounce the link.
Reorder the bit clearing and the context disable.
Examine the software state and send context status as well as the
egress status to determine if a send context is in the halted state.
Promote the check macros to static functions for consistency with the
new check and to follow kernel style.
Remove an unused define that refers to the egress timeout.
Cc: <stable(a)vger.kernel.org> # 4.9.x
Reviewed-by: Mitko Haralanov <mitko.haralanov(a)intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn(a)intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl(a)intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro(a)intel.com>
Signed-off-by: Doug Ledford <dledford(a)redhat.com>
diff --git a/drivers/infiniband/hw/hfi1/file_ops.c b/drivers/infiniband/hw/hfi1/file_ops.c
index 1b778fd16a32..c9d23c37a371 100644
--- a/drivers/infiniband/hw/hfi1/file_ops.c
+++ b/drivers/infiniband/hw/hfi1/file_ops.c
@@ -689,8 +689,8 @@ static int hfi1_file_close(struct inode *inode, struct file *fp)
* checks to default and disable the send context.
*/
if (uctxt->sc) {
- set_pio_integrity(uctxt->sc);
sc_disable(uctxt->sc);
+ set_pio_integrity(uctxt->sc);
}
hfi1_free_ctxt_rcv_groups(uctxt);
diff --git a/drivers/infiniband/hw/hfi1/pio.c b/drivers/infiniband/hw/hfi1/pio.c
index 40dac4d16eb8..9cac15d10c4f 100644
--- a/drivers/infiniband/hw/hfi1/pio.c
+++ b/drivers/infiniband/hw/hfi1/pio.c
@@ -50,8 +50,6 @@
#include "qp.h"
#include "trace.h"
-#define SC_CTXT_PACKET_EGRESS_TIMEOUT 350 /* in chip cycles */
-
#define SC(name) SEND_CTXT_##name
/*
* Send Context functions
@@ -961,15 +959,40 @@ void sc_disable(struct send_context *sc)
}
/* return SendEgressCtxtStatus.PacketOccupancy */
-#define packet_occupancy(r) \
- (((r) & SEND_EGRESS_CTXT_STATUS_CTXT_EGRESS_PACKET_OCCUPANCY_SMASK)\
- >> SEND_EGRESS_CTXT_STATUS_CTXT_EGRESS_PACKET_OCCUPANCY_SHIFT)
+static u64 packet_occupancy(u64 reg)
+{
+ return (reg &
+ SEND_EGRESS_CTXT_STATUS_CTXT_EGRESS_PACKET_OCCUPANCY_SMASK)
+ >> SEND_EGRESS_CTXT_STATUS_CTXT_EGRESS_PACKET_OCCUPANCY_SHIFT;
+}
/* is egress halted on the context? */
-#define egress_halted(r) \
- ((r) & SEND_EGRESS_CTXT_STATUS_CTXT_EGRESS_HALT_STATUS_SMASK)
+static bool egress_halted(u64 reg)
+{
+ return !!(reg & SEND_EGRESS_CTXT_STATUS_CTXT_EGRESS_HALT_STATUS_SMASK);
+}
-/* wait for packet egress, optionally pause for credit return */
+/* is the send context halted? */
+static bool is_sc_halted(struct hfi1_devdata *dd, u32 hw_context)
+{
+ return !!(read_kctxt_csr(dd, hw_context, SC(STATUS)) &
+ SC(STATUS_CTXT_HALTED_SMASK));
+}
+
+/**
+ * sc_wait_for_packet_egress
+ * @sc: valid send context
+ * @pause: wait for credit return
+ *
+ * Wait for packet egress, optionally pause for credit return
+ *
+ * Egress halt and Context halt are not necessarily the same thing, so
+ * check for both.
+ *
+ * NOTE: The context halt bit may not be set immediately. Because of this,
+ * it is necessary to check the SW SFC_HALTED bit (set in the IRQ) and the HW
+ * context bit to determine if the context is halted.
+ */
static void sc_wait_for_packet_egress(struct send_context *sc, int pause)
{
struct hfi1_devdata *dd = sc->dd;
@@ -981,8 +1004,9 @@ static void sc_wait_for_packet_egress(struct send_context *sc, int pause)
reg_prev = reg;
reg = read_csr(dd, sc->hw_context * 8 +
SEND_EGRESS_CTXT_STATUS);
- /* done if egress is stopped */
- if (egress_halted(reg))
+ /* done if any halt bits, SW or HW are set */
+ if (sc->flags & SCF_HALTED ||
+ is_sc_halted(dd, sc->hw_context) || egress_halted(reg))
break;
reg = packet_occupancy(reg);
if (reg == 0)
The patch below does not apply to the 4.9-stable tree.
If someone wants it applied there, or to any other stable or longterm
tree, then please email the backport, including the original git commit
id to <stable(a)vger.kernel.org>.
thanks,
greg k-h
------------------ original commit in Linus's tree ------------------
>From 08bb558ac11ab944e0539e78619d7b4c356278bd Mon Sep 17 00:00:00 2001
From: Jack Morgenstein <jackm(a)dev.mellanox.co.il>
Date: Wed, 23 May 2018 15:30:30 +0300
Subject: [PATCH] IB/core: Make testing MR flags for writability a static
inline function
Make the MR writability flags check, which is performed in umem.c,
a static inline function in file ib_verbs.h
This allows the function to be used by low-level infiniband drivers.
Cc: <stable(a)vger.kernel.org>
Signed-off-by: Jason Gunthorpe <jgg(a)mellanox.com>
Signed-off-by: Jack Morgenstein <jackm(a)dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leonro(a)mellanox.com>
diff --git a/drivers/infiniband/core/umem.c b/drivers/infiniband/core/umem.c
index 2b6c9b516070..d76455edd292 100644
--- a/drivers/infiniband/core/umem.c
+++ b/drivers/infiniband/core/umem.c
@@ -119,16 +119,7 @@ struct ib_umem *ib_umem_get(struct ib_ucontext *context, unsigned long addr,
umem->length = size;
umem->address = addr;
umem->page_shift = PAGE_SHIFT;
- /*
- * We ask for writable memory if any of the following
- * access flags are set. "Local write" and "remote write"
- * obviously require write access. "Remote atomic" can do
- * things like fetch and add, which will modify memory, and
- * "MW bind" can change permissions by binding a window.
- */
- umem->writable = !!(access &
- (IB_ACCESS_LOCAL_WRITE | IB_ACCESS_REMOTE_WRITE |
- IB_ACCESS_REMOTE_ATOMIC | IB_ACCESS_MW_BIND));
+ umem->writable = ib_access_writable(access);
if (access & IB_ACCESS_ON_DEMAND) {
ret = ib_umem_odp_get(context, umem, access);
diff --git a/include/rdma/ib_verbs.h b/include/rdma/ib_verbs.h
index 9fc8a825aa28..20fa5c591e81 100644
--- a/include/rdma/ib_verbs.h
+++ b/include/rdma/ib_verbs.h
@@ -3734,6 +3734,20 @@ static inline int ib_check_mr_access(int flags)
return 0;
}
+static inline bool ib_access_writable(int access_flags)
+{
+ /*
+ * We have writable memory backing the MR if any of the following
+ * access flags are set. "Local write" and "remote write" obviously
+ * require write access. "Remote atomic" can do things like fetch and
+ * add, which will modify memory, and "MW bind" can change permissions
+ * by binding a window.
+ */
+ return access_flags &
+ (IB_ACCESS_LOCAL_WRITE | IB_ACCESS_REMOTE_WRITE |
+ IB_ACCESS_REMOTE_ATOMIC | IB_ACCESS_MW_BIND);
+}
+
/**
* ib_check_mr_status: lightweight check of MR status.
* This routine may provide status checks on a selected
The patch below does not apply to the 4.9-stable tree.
If someone wants it applied there, or to any other stable or longterm
tree, then please email the backport, including the original git commit
id to <stable(a)vger.kernel.org>.
thanks,
greg k-h
------------------ original commit in Linus's tree ------------------
>From 3ab2011ea368ec3433ad49e1b9e1c7b70d2e65df Mon Sep 17 00:00:00 2001
From: Tadeusz Struk <tadeusz.struk(a)intel.com>
Date: Tue, 22 May 2018 14:37:18 -0700
Subject: [PATCH] tpm: fix race condition in tpm_common_write()
There is a race condition in tpm_common_write function allowing
two threads on the same /dev/tpm<N>, or two different applications
on the same /dev/tpmrm<N> to overwrite each other commands/responses.
Fixed this by taking the priv->buffer_mutex early in the function.
Also converted the priv->data_pending from atomic to a regular size_t
type. There is no need for it to be atomic since it is only touched
under the protection of the priv->buffer_mutex.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable(a)vger.kernel.org
Signed-off-by: Tadeusz Struk <tadeusz.struk(a)intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen(a)linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen(a)linux.intel.com>
diff --git a/drivers/char/tpm/tpm-dev-common.c b/drivers/char/tpm/tpm-dev-common.c
index 230b99288024..e4a04b2d3c32 100644
--- a/drivers/char/tpm/tpm-dev-common.c
+++ b/drivers/char/tpm/tpm-dev-common.c
@@ -37,7 +37,7 @@ static void timeout_work(struct work_struct *work)
struct file_priv *priv = container_of(work, struct file_priv, work);
mutex_lock(&priv->buffer_mutex);
- atomic_set(&priv->data_pending, 0);
+ priv->data_pending = 0;
memset(priv->data_buffer, 0, sizeof(priv->data_buffer));
mutex_unlock(&priv->buffer_mutex);
}
@@ -46,7 +46,6 @@ void tpm_common_open(struct file *file, struct tpm_chip *chip,
struct file_priv *priv)
{
priv->chip = chip;
- atomic_set(&priv->data_pending, 0);
mutex_init(&priv->buffer_mutex);
timer_setup(&priv->user_read_timer, user_reader_timeout, 0);
INIT_WORK(&priv->work, timeout_work);
@@ -58,29 +57,24 @@ ssize_t tpm_common_read(struct file *file, char __user *buf,
size_t size, loff_t *off)
{
struct file_priv *priv = file->private_data;
- ssize_t ret_size;
- ssize_t orig_ret_size;
+ ssize_t ret_size = 0;
int rc;
del_singleshot_timer_sync(&priv->user_read_timer);
flush_work(&priv->work);
- ret_size = atomic_read(&priv->data_pending);
- if (ret_size > 0) { /* relay data */
- orig_ret_size = ret_size;
- if (size < ret_size)
- ret_size = size;
+ mutex_lock(&priv->buffer_mutex);
- mutex_lock(&priv->buffer_mutex);
+ if (priv->data_pending) {
+ ret_size = min_t(ssize_t, size, priv->data_pending);
rc = copy_to_user(buf, priv->data_buffer, ret_size);
- memset(priv->data_buffer, 0, orig_ret_size);
+ memset(priv->data_buffer, 0, priv->data_pending);
if (rc)
ret_size = -EFAULT;
- mutex_unlock(&priv->buffer_mutex);
+ priv->data_pending = 0;
}
- atomic_set(&priv->data_pending, 0);
-
+ mutex_unlock(&priv->buffer_mutex);
return ret_size;
}
@@ -91,17 +85,19 @@ ssize_t tpm_common_write(struct file *file, const char __user *buf,
size_t in_size = size;
ssize_t out_size;
+ if (in_size > TPM_BUFSIZE)
+ return -E2BIG;
+
+ mutex_lock(&priv->buffer_mutex);
+
/* Cannot perform a write until the read has cleared either via
* tpm_read or a user_read_timer timeout. This also prevents split
* buffered writes from blocking here.
*/
- if (atomic_read(&priv->data_pending) != 0)
+ if (priv->data_pending != 0) {
+ mutex_unlock(&priv->buffer_mutex);
return -EBUSY;
-
- if (in_size > TPM_BUFSIZE)
- return -E2BIG;
-
- mutex_lock(&priv->buffer_mutex);
+ }
if (copy_from_user
(priv->data_buffer, (void __user *) buf, in_size)) {
@@ -132,7 +128,7 @@ ssize_t tpm_common_write(struct file *file, const char __user *buf,
return out_size;
}
- atomic_set(&priv->data_pending, out_size);
+ priv->data_pending = out_size;
mutex_unlock(&priv->buffer_mutex);
/* Set a timeout by which the reader must come claim the result */
@@ -149,5 +145,5 @@ void tpm_common_release(struct file *file, struct file_priv *priv)
del_singleshot_timer_sync(&priv->user_read_timer);
flush_work(&priv->work);
file->private_data = NULL;
- atomic_set(&priv->data_pending, 0);
+ priv->data_pending = 0;
}
diff --git a/drivers/char/tpm/tpm-dev.h b/drivers/char/tpm/tpm-dev.h
index ba3b6f9dacf7..b24cfb4d3ee1 100644
--- a/drivers/char/tpm/tpm-dev.h
+++ b/drivers/char/tpm/tpm-dev.h
@@ -8,7 +8,7 @@ struct file_priv {
struct tpm_chip *chip;
/* Data passed to and from the tpm via the read/write calls */
- atomic_t data_pending;
+ size_t data_pending;
struct mutex buffer_mutex;
struct timer_list user_read_timer; /* user needs to claim result */
The patch below does not apply to the 4.14-stable tree.
If someone wants it applied there, or to any other stable or longterm
tree, then please email the backport, including the original git commit
id to <stable(a)vger.kernel.org>.
thanks,
greg k-h
------------------ original commit in Linus's tree ------------------
>From 2f872ddcdb1e8e2186162616cea4581b8403849d Mon Sep 17 00:00:00 2001
From: Miquel Raynal <miquel.raynal(a)bootlin.com>
Date: Tue, 22 May 2018 11:40:28 +0200
Subject: [PATCH] arm64: dts: marvell: fix CP110 ICU node size
ICU size in CP110 is not 0x10 but at least 0x440 bytes long (from the
specification).
Fixes: 6ef84a827c37 ("arm64: dts: marvell: enable GICP and ICU on Armada 7K/8K")
Cc: stable(a)vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal(a)bootlin.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni(a)bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement(a)bootlin.com>
diff --git a/arch/arm64/boot/dts/marvell/armada-cp110.dtsi b/arch/arm64/boot/dts/marvell/armada-cp110.dtsi
index ed2f1237ea1e..8259b32f0ced 100644
--- a/arch/arm64/boot/dts/marvell/armada-cp110.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-cp110.dtsi
@@ -149,7 +149,7 @@
CP110_LABEL(icu): interrupt-controller@1e0000 {
compatible = "marvell,cp110-icu";
- reg = <0x1e0000 0x10>;
+ reg = <0x1e0000 0x440>;
#interrupt-cells = <3>;
interrupt-controller;
msi-parent = <&gicp>;
The patch below does not apply to the 4.4-stable tree.
If someone wants it applied there, or to any other stable or longterm
tree, then please email the backport, including the original git commit
id to <stable(a)vger.kernel.org>.
thanks,
greg k-h
------------------ original commit in Linus's tree ------------------
>From ac9816dcbab53c57bcf1d7b15370b08f1e284318 Mon Sep 17 00:00:00 2001
From: Akshay Adiga <akshay.adiga(a)linux.vnet.ibm.com>
Date: Wed, 16 May 2018 17:32:14 +0530
Subject: [PATCH] powerpc/powernv/cpuidle: Init all present cpus for deep
states
Init all present cpus for deep states instead of "all possible" cpus.
Init fails if a possible cpu is guarded. Resulting in making only
non-deep states available for cpuidle/hotplug.
Stewart says, this means that for single threaded workloads, if you
guard out a CPU core you'll not get WoF (Workload Optimised
Frequency), which means that performance goes down when you wouldn't
expect it to.
Fixes: 77b54e9f213f ("powernv/powerpc: Add winkle support for offline cpus")
Cc: stable(a)vger.kernel.org # v3.19+
Signed-off-by: Akshay Adiga <akshay.adiga(a)linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe(a)ellerman.id.au>
diff --git a/arch/powerpc/platforms/powernv/idle.c b/arch/powerpc/platforms/powernv/idle.c
index 1f12ab1e6030..1c5d0675b43c 100644
--- a/arch/powerpc/platforms/powernv/idle.c
+++ b/arch/powerpc/platforms/powernv/idle.c
@@ -79,7 +79,7 @@ static int pnv_save_sprs_for_deep_states(void)
uint64_t msr_val = MSR_IDLE;
uint64_t psscr_val = pnv_deepest_stop_psscr_val;
- for_each_possible_cpu(cpu) {
+ for_each_present_cpu(cpu) {
uint64_t pir = get_hard_smp_processor_id(cpu);
uint64_t hsprg0_val = (uint64_t)paca_ptrs[cpu];
@@ -814,7 +814,7 @@ static int __init pnv_init_idle_states(void)
int cpu;
pr_info("powernv: idle: Saving PACA pointers of all CPUs in their thread sibling PACA\n");
- for_each_possible_cpu(cpu) {
+ for_each_present_cpu(cpu) {
int base_cpu = cpu_first_thread_sibling(cpu);
int idx = cpu_thread_in_core(cpu);
int i;
The patch below does not apply to the 4.9-stable tree.
If someone wants it applied there, or to any other stable or longterm
tree, then please email the backport, including the original git commit
id to <stable(a)vger.kernel.org>.
thanks,
greg k-h
------------------ original commit in Linus's tree ------------------
>From ac9816dcbab53c57bcf1d7b15370b08f1e284318 Mon Sep 17 00:00:00 2001
From: Akshay Adiga <akshay.adiga(a)linux.vnet.ibm.com>
Date: Wed, 16 May 2018 17:32:14 +0530
Subject: [PATCH] powerpc/powernv/cpuidle: Init all present cpus for deep
states
Init all present cpus for deep states instead of "all possible" cpus.
Init fails if a possible cpu is guarded. Resulting in making only
non-deep states available for cpuidle/hotplug.
Stewart says, this means that for single threaded workloads, if you
guard out a CPU core you'll not get WoF (Workload Optimised
Frequency), which means that performance goes down when you wouldn't
expect it to.
Fixes: 77b54e9f213f ("powernv/powerpc: Add winkle support for offline cpus")
Cc: stable(a)vger.kernel.org # v3.19+
Signed-off-by: Akshay Adiga <akshay.adiga(a)linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe(a)ellerman.id.au>
diff --git a/arch/powerpc/platforms/powernv/idle.c b/arch/powerpc/platforms/powernv/idle.c
index 1f12ab1e6030..1c5d0675b43c 100644
--- a/arch/powerpc/platforms/powernv/idle.c
+++ b/arch/powerpc/platforms/powernv/idle.c
@@ -79,7 +79,7 @@ static int pnv_save_sprs_for_deep_states(void)
uint64_t msr_val = MSR_IDLE;
uint64_t psscr_val = pnv_deepest_stop_psscr_val;
- for_each_possible_cpu(cpu) {
+ for_each_present_cpu(cpu) {
uint64_t pir = get_hard_smp_processor_id(cpu);
uint64_t hsprg0_val = (uint64_t)paca_ptrs[cpu];
@@ -814,7 +814,7 @@ static int __init pnv_init_idle_states(void)
int cpu;
pr_info("powernv: idle: Saving PACA pointers of all CPUs in their thread sibling PACA\n");
- for_each_possible_cpu(cpu) {
+ for_each_present_cpu(cpu) {
int base_cpu = cpu_first_thread_sibling(cpu);
int idx = cpu_thread_in_core(cpu);
int i;
The patch below does not apply to the 4.4-stable tree.
If someone wants it applied there, or to any other stable or longterm
tree, then please email the backport, including the original git commit
id to <stable(a)vger.kernel.org>.
thanks,
greg k-h
------------------ original commit in Linus's tree ------------------
>From 8a301eb16d99983a4961f884690ec97b92e7dcfe Mon Sep 17 00:00:00 2001
From: Tejun Heo <tj(a)kernel.org>
Date: Fri, 2 Feb 2018 09:54:14 -0800
Subject: [PATCH] fuse: fix congested state leak on aborted connections
If a connection gets aborted while congested, FUSE can leave
nr_wb_congested[] stuck until reboot causing wait_iff_congested() to
wait spuriously which can lead to severe performance degradation.
The leak is caused by gating congestion state clearing with
fc->connected test in request_end(). This was added way back in 2009
by 26c3679101db ("fuse: destroy bdi on umount"). While the commit
description doesn't explain why the test was added, it most likely was
to avoid dereferencing bdi after it got destroyed.
Since then, bdi lifetime rules have changed many times and now we're
always guaranteed to have access to the bdi while the superblock is
alive (fc->sb).
Drop fc->connected conditional to avoid leaking congestion states.
Signed-off-by: Tejun Heo <tj(a)kernel.org>
Reported-by: Joshua Miller <joshmiller(a)fb.com>
Cc: Johannes Weiner <hannes(a)cmpxchg.org>
Cc: stable(a)vger.kernel.org # v2.6.29+
Acked-by: Jan Kara <jack(a)suse.cz>
Signed-off-by: Miklos Szeredi <mszeredi(a)redhat.com>
diff --git a/fs/fuse/dev.c b/fs/fuse/dev.c
index 686631f12001..e03ca14f40e9 100644
--- a/fs/fuse/dev.c
+++ b/fs/fuse/dev.c
@@ -385,8 +385,7 @@ static void request_end(struct fuse_conn *fc, struct fuse_req *req)
if (!fc->blocked && waitqueue_active(&fc->blocked_waitq))
wake_up(&fc->blocked_waitq);
- if (fc->num_background == fc->congestion_threshold &&
- fc->connected && fc->sb) {
+ if (fc->num_background == fc->congestion_threshold && fc->sb) {
clear_bdi_congested(fc->sb->s_bdi, BLK_RW_SYNC);
clear_bdi_congested(fc->sb->s_bdi, BLK_RW_ASYNC);
}
The patch below does not apply to the 4.9-stable tree.
If someone wants it applied there, or to any other stable or longterm
tree, then please email the backport, including the original git commit
id to <stable(a)vger.kernel.org>.
thanks,
greg k-h
------------------ original commit in Linus's tree ------------------
>From 8a301eb16d99983a4961f884690ec97b92e7dcfe Mon Sep 17 00:00:00 2001
From: Tejun Heo <tj(a)kernel.org>
Date: Fri, 2 Feb 2018 09:54:14 -0800
Subject: [PATCH] fuse: fix congested state leak on aborted connections
If a connection gets aborted while congested, FUSE can leave
nr_wb_congested[] stuck until reboot causing wait_iff_congested() to
wait spuriously which can lead to severe performance degradation.
The leak is caused by gating congestion state clearing with
fc->connected test in request_end(). This was added way back in 2009
by 26c3679101db ("fuse: destroy bdi on umount"). While the commit
description doesn't explain why the test was added, it most likely was
to avoid dereferencing bdi after it got destroyed.
Since then, bdi lifetime rules have changed many times and now we're
always guaranteed to have access to the bdi while the superblock is
alive (fc->sb).
Drop fc->connected conditional to avoid leaking congestion states.
Signed-off-by: Tejun Heo <tj(a)kernel.org>
Reported-by: Joshua Miller <joshmiller(a)fb.com>
Cc: Johannes Weiner <hannes(a)cmpxchg.org>
Cc: stable(a)vger.kernel.org # v2.6.29+
Acked-by: Jan Kara <jack(a)suse.cz>
Signed-off-by: Miklos Szeredi <mszeredi(a)redhat.com>
diff --git a/fs/fuse/dev.c b/fs/fuse/dev.c
index 686631f12001..e03ca14f40e9 100644
--- a/fs/fuse/dev.c
+++ b/fs/fuse/dev.c
@@ -385,8 +385,7 @@ static void request_end(struct fuse_conn *fc, struct fuse_req *req)
if (!fc->blocked && waitqueue_active(&fc->blocked_waitq))
wake_up(&fc->blocked_waitq);
- if (fc->num_background == fc->congestion_threshold &&
- fc->connected && fc->sb) {
+ if (fc->num_background == fc->congestion_threshold && fc->sb) {
clear_bdi_congested(fc->sb->s_bdi, BLK_RW_SYNC);
clear_bdi_congested(fc->sb->s_bdi, BLK_RW_ASYNC);
}
The patch below does not apply to the 4.9-stable tree.
If someone wants it applied there, or to any other stable or longterm
tree, then please email the backport, including the original git commit
id to <stable(a)vger.kernel.org>.
thanks,
greg k-h
------------------ original commit in Linus's tree ------------------
>From 756b56a9e832e063edc83be7c3889e98c536dd2b Mon Sep 17 00:00:00 2001
From: "Steven Rostedt (VMware)" <rostedt(a)goodmis.org>
Date: Mon, 14 May 2018 15:40:29 -0400
Subject: [PATCH] ftrace/selftest: Have the reset_trigger code be a bit more
careful
The trigger code is picky in how it can be disabled as there may be
dependencies between different events and synthetic events. Change the order
on how triggers are reset.
1) Reset triggers of all synthetic events first
2) Remove triggers with actions attached to them
3) Remove all other triggers
If this order isn't followed, then some triggers will not be reset, and an
error may happen because a trigger is busy.
Cc: stable(a)vger.kernel.org
Fixes: cfa0963dc474f ("kselftests/ftrace : Add event trigger testcases")
Reviewed-by: Namhyung Kim <namhyung(a)kernel.org>
Acked-by: Masami Hiramatsu <mhiramat(a)kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt(a)goodmis.org>
diff --git a/tools/testing/selftests/ftrace/test.d/functions b/tools/testing/selftests/ftrace/test.d/functions
index 2a4f16fc9819..8393b1c06027 100644
--- a/tools/testing/selftests/ftrace/test.d/functions
+++ b/tools/testing/selftests/ftrace/test.d/functions
@@ -15,14 +15,29 @@ reset_tracer() { # reset the current tracer
echo nop > current_tracer
}
-reset_trigger() { # reset all current setting triggers
- grep -v ^# events/*/*/trigger |
+reset_trigger_file() {
+ # remove action triggers first
+ grep -H ':on[^:]*(' $@ |
+ while read line; do
+ cmd=`echo $line | cut -f2- -d: | cut -f1 -d" "`
+ file=`echo $line | cut -f1 -d:`
+ echo "!$cmd" >> $file
+ done
+ grep -Hv ^# $@ |
while read line; do
cmd=`echo $line | cut -f2- -d: | cut -f1 -d" "`
- echo "!$cmd" > `echo $line | cut -f1 -d:`
+ file=`echo $line | cut -f1 -d:`
+ echo "!$cmd" > $file
done
}
+reset_trigger() { # reset all current setting triggers
+ if [ -d events/synthetic ]; then
+ reset_trigger_file events/synthetic/*/trigger
+ fi
+ reset_trigger_file events/*/*/trigger
+}
+
reset_events_filter() { # reset all current setting filters
grep -v ^none events/*/*/filter |
while read line; do
The patch below does not apply to the 4.9-stable tree.
If someone wants it applied there, or to any other stable or longterm
tree, then please email the backport, including the original git commit
id to <stable(a)vger.kernel.org>.
thanks,
greg k-h
------------------ original commit in Linus's tree ------------------
>From c5c2a97b3ac7d1ec19e7cff9e38caca6afefc3de Mon Sep 17 00:00:00 2001
From: Waldemar Rymarkiewicz <waldemar.rymarkiewicz(a)gmail.com>
Date: Thu, 14 Jun 2018 15:56:08 +0200
Subject: [PATCH] PM / OPP: Update voltage in case freq == old_freq
This commit fixes a rare but possible case when the clk rate is updated
without update of the regulator voltage.
At boot up, CPUfreq checks if the system is running at the right freq. This
is a sanity check in case a bootloader set clk rate that is outside of freq
table present with cpufreq core. In such cases system can be unstable so
better to change it to a freq that is preset in freq-table.
The CPUfreq takes next freq that is >= policy->cur and this is our
target_freq that needs to be set now.
dev_pm_opp_set_rate(dev, target_freq) checks the target_freq and the
old_freq (a current rate). If these are equal it returns early. If not,
it searches for OPP (old_opp) that fits best to old_freq (not listed in
the table) and updates old_freq (!).
Here, we can end up with old_freq = old_opp.rate = target_freq, which
is not handled in _generic_set_opp_regulator(). It's supposed to update
voltage only when freq > old_freq || freq > old_freq.
if (freq > old_freq) {
ret = _set_opp_voltage(dev, reg, new_supply);
[...]
if (freq < old_freq) {
ret = _set_opp_voltage(dev, reg, new_supply);
if (ret)
It results in, no voltage update while clk rate is updated.
Example:
freq-table = {
1000MHz 1.15V
666MHZ 1.10V
333MHz 1.05V
}
boot-up-freq = 800MHz # not listed in freq-table
freq = target_freq = 1GHz
old_freq = 800Mhz
old_opp = _find_freq_ceil(opp_table, &old_freq); #(old_freq is modified!)
old_freq = 1GHz
Fixes: 6a0712f6f199 ("PM / OPP: Add dev_pm_opp_set_rate()")
Cc: 4.6+ <stable(a)vger.kernel.org> # v4.6+
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz(a)gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar(a)linaro.org>
diff --git a/drivers/opp/core.c b/drivers/opp/core.c
index ab2f3fead6b1..31ff03dbeb83 100644
--- a/drivers/opp/core.c
+++ b/drivers/opp/core.c
@@ -598,7 +598,7 @@ static int _generic_set_opp_regulator(const struct opp_table *opp_table,
}
/* Scaling up? Scale voltage before frequency */
- if (freq > old_freq) {
+ if (freq >= old_freq) {
ret = _set_opp_voltage(dev, reg, new_supply);
if (ret)
goto restore_voltage;
The patch below does not apply to the 4.17-stable tree.
If someone wants it applied there, or to any other stable or longterm
tree, then please email the backport, including the original git commit
id to <stable(a)vger.kernel.org>.
thanks,
greg k-h
------------------ original commit in Linus's tree ------------------
>From e935dba111621bd6a0c5d48e6511a4d9885103b4 Mon Sep 17 00:00:00 2001
From: Marek Szyprowski <m.szyprowski(a)samsung.com>
Date: Wed, 16 May 2018 10:42:39 +0200
Subject: [PATCH] spi: spi-s3c64xx: Fix system resume support
Since Linux v4.10 release (commit 1d9174fbc55e "PM / Runtime: Defer
resuming of the device in pm_runtime_force_resume()"),
pm_runtime_force_resume() function doesn't runtime resume device if it was
not runtime active before system suspend. Thus, driver should not do any
register access after pm_runtime_force_resume() without checking the
runtime status of the device. To fix this issue, simply move
s3c64xx_spi_hwinit() call to s3c64xx_spi_runtime_resume() to ensure that
hardware is always properly initialized. This fixes Synchronous external
abort issue on system suspend/resume cycle on newer Exynos SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski(a)samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk(a)kernel.org>
Signed-off-by: Mark Brown <broonie(a)kernel.org>
Cc: stable(a)vger.kernel.org
diff --git a/drivers/spi/spi-s3c64xx.c b/drivers/spi/spi-s3c64xx.c
index f55dc78957ad..7b7151ec14c8 100644
--- a/drivers/spi/spi-s3c64xx.c
+++ b/drivers/spi/spi-s3c64xx.c
@@ -1292,8 +1292,6 @@ static int s3c64xx_spi_resume(struct device *dev)
if (ret < 0)
return ret;
- s3c64xx_spi_hwinit(sdd);
-
return spi_master_resume(master);
}
#endif /* CONFIG_PM_SLEEP */
@@ -1331,6 +1329,8 @@ static int s3c64xx_spi_runtime_resume(struct device *dev)
if (ret != 0)
goto err_disable_src_clk;
+ s3c64xx_spi_hwinit(sdd);
+
return 0;
err_disable_src_clk:
We were copying our last cipher block into the request for use as IV for
all modes of operations. Fix this by discerning the behaviour based on
the mode of operation used: copy ciphertext for CBC, update counter for
CTR.
CC: stable(a)vger.kernel.org
Fixes: 63ee04c8b491 ("crypto: ccree - add skcipher support")
Reported by: Hadar Gat <hadar.gat(a)arm.com>
Signed-off-by: Gilad Ben-Yossef <gilad(a)benyossef.com>
---
drivers/crypto/ccree/cc_cipher.c | 111 +++++++++++++++++++++++++++++----------
1 file changed, 84 insertions(+), 27 deletions(-)
diff --git a/drivers/crypto/ccree/cc_cipher.c b/drivers/crypto/ccree/cc_cipher.c
index d2810c1..958ced3 100644
--- a/drivers/crypto/ccree/cc_cipher.c
+++ b/drivers/crypto/ccree/cc_cipher.c
@@ -593,34 +593,82 @@ static void cc_setup_cipher_data(struct crypto_tfm *tfm,
}
}
+/*
+ * Update a CTR-AES 128 bit counter
+ */
+static void cc_update_ctr(u8 *ctr, unsigned int increment)
+{
+ if (IS_ENABLED(CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS) ||
+ IS_ALIGNED((unsigned long)ctr, 8)) {
+
+ __be64 *high_be = (__be64 *)ctr;
+ __be64 *low_be = high_be + 1;
+ u64 orig_low = __be64_to_cpu(*low_be);
+ u64 new_low = orig_low + (u64)increment;
+
+ *low_be = __cpu_to_be64(new_low);
+
+ if (new_low < orig_low)
+ *high_be = __cpu_to_be64(__be64_to_cpu(*high_be) + 1);
+ } else {
+ u8 *pos = (ctr + AES_BLOCK_SIZE);
+ u8 val;
+ unsigned int size;
+
+ for (; increment; increment--)
+ for (size = AES_BLOCK_SIZE; size; size--) {
+ val = *--pos + 1;
+ *pos = val;
+ if (val)
+ break;
+ }
+ }
+}
+
static void cc_cipher_complete(struct device *dev, void *cc_req, int err)
{
struct skcipher_request *req = (struct skcipher_request *)cc_req;
struct scatterlist *dst = req->dst;
struct scatterlist *src = req->src;
struct cipher_req_ctx *req_ctx = skcipher_request_ctx(req);
- struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
- unsigned int ivsize = crypto_skcipher_ivsize(tfm);
+ struct crypto_skcipher *sk_tfm = crypto_skcipher_reqtfm(req);
+ struct crypto_tfm *tfm = crypto_skcipher_tfm(sk_tfm);
+ struct cc_cipher_ctx *ctx_p = crypto_tfm_ctx(tfm);
+ unsigned int ivsize = crypto_skcipher_ivsize(sk_tfm);
+ unsigned int len;
- cc_unmap_cipher_request(dev, req_ctx, ivsize, src, dst);
- kzfree(req_ctx->iv);
+ switch (ctx_p->cipher_mode) {
+ case DRV_CIPHER_CBC:
+ /*
+ * The crypto API expects us to set the req->iv to the last
+ * ciphertext block. For encrypt, simply copy from the result.
+ * For decrypt, we must copy from a saved buffer since this
+ * could be an in-place decryption operation and the src is
+ * lost by this point.
+ */
+ if (req_ctx->gen_ctx.op_type == DRV_CRYPTO_DIRECTION_DECRYPT) {
+ memcpy(req->iv, req_ctx->backup_info, ivsize);
+ kzfree(req_ctx->backup_info);
+ } else if (!err) {
+ len = req->cryptlen - ivsize;
+ scatterwalk_map_and_copy(req->iv, req->dst, len,
+ ivsize, 0);
+ }
+ break;
- /*
- * The crypto API expects us to set the req->iv to the last
- * ciphertext block. For encrypt, simply copy from the result.
- * For decrypt, we must copy from a saved buffer since this
- * could be an in-place decryption operation and the src is
- * lost by this point.
- */
- if (req_ctx->gen_ctx.op_type == DRV_CRYPTO_DIRECTION_DECRYPT) {
- memcpy(req->iv, req_ctx->backup_info, ivsize);
- kzfree(req_ctx->backup_info);
- } else if (!err) {
- scatterwalk_map_and_copy(req->iv, req->dst,
- (req->cryptlen - ivsize),
- ivsize, 0);
+ case DRV_CIPHER_CTR:
+ /* Compute the counter of the last block */
+ len = ALIGN(req->cryptlen, AES_BLOCK_SIZE) / AES_BLOCK_SIZE;
+ cc_update_ctr((u8 *)req->iv, len);
+ break;
+
+ default:
+ break;
}
+ cc_unmap_cipher_request(dev, req_ctx, ivsize, src, dst);
+ kzfree(req_ctx->iv);
+
skcipher_request_complete(req, err);
}
@@ -752,20 +800,29 @@ static int cc_cipher_encrypt(struct skcipher_request *req)
static int cc_cipher_decrypt(struct skcipher_request *req)
{
struct crypto_skcipher *sk_tfm = crypto_skcipher_reqtfm(req);
+ struct crypto_tfm *tfm = crypto_skcipher_tfm(sk_tfm);
+ struct cc_cipher_ctx *ctx_p = crypto_tfm_ctx(tfm);
struct cipher_req_ctx *req_ctx = skcipher_request_ctx(req);
unsigned int ivsize = crypto_skcipher_ivsize(sk_tfm);
gfp_t flags = cc_gfp_flags(&req->base);
+ unsigned int len;
- /*
- * Allocate and save the last IV sized bytes of the source, which will
- * be lost in case of in-place decryption and might be needed for CTS.
- */
- req_ctx->backup_info = kmalloc(ivsize, flags);
- if (!req_ctx->backup_info)
- return -ENOMEM;
+ if (ctx_p->cipher_mode == DRV_CIPHER_CBC) {
+
+ /* Allocate and save the last IV sized bytes of the source,
+ * which will be lost in case of in-place decryption.
+ */
+ req_ctx->backup_info = kzalloc(ivsize, flags);
+ if (!req_ctx->backup_info)
+ return -ENOMEM;
+
+ len = req->cryptlen - ivsize;
+ scatterwalk_map_and_copy(req_ctx->backup_info, req->src, len,
+ ivsize, 0);
+ } else {
+ req_ctx->backup_info = NULL;
+ }
- scatterwalk_map_and_copy(req_ctx->backup_info, req->src,
- (req->cryptlen - ivsize), ivsize, 0);
req_ctx->is_giv = false;
return cc_cipher_process(req, DRV_CRYPTO_DIRECTION_DECRYPT);
--
2.7.4
The pinctrl settings were incorrect for the touchscreen interrupt line, causing
an interrupt storm. This change has been tested with both the atmel_mxt_ts and
RMI4 drivers on the RDU1 units.
The value 0x4 comes from the value of register IOMUXC_SW_PAD_CTL_PAD_CSI1_D8
from the old vendor kernel.
Signed-off-by: Nick Dyer <nick(a)shmanahar.org>
Fixes: ceef0396f367 ("ARM: dts: imx: add ZII RDU1 board")
Cc: <stable(a)vger.kernel.org> # 4.15+
---
Changes in v3:
- Update commit message to add source of 0x4 value, fixes tag and CC stable
Changes in v2:
- Use hex, only alter IRQ line config
arch/arm/boot/dts/imx51-zii-rdu1.dts | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/imx51-zii-rdu1.dts b/arch/arm/boot/dts/imx51-zii-rdu1.dts
index df9eca94d812..8a878687197b 100644
--- a/arch/arm/boot/dts/imx51-zii-rdu1.dts
+++ b/arch/arm/boot/dts/imx51-zii-rdu1.dts
@@ -770,7 +770,7 @@
pinctrl_ts: tsgrp {
fsl,pins = <
- MX51_PAD_CSI1_D8__GPIO3_12 0x85
+ MX51_PAD_CSI1_D8__GPIO3_12 0x04
MX51_PAD_CSI1_D9__GPIO3_13 0x85
>;
};
--
2.17.1
The patch titled
Subject: kasan: depend on CONFIG_SLUB_DEBUG
has been removed from the -mm tree. Its filename was
kasan-depend-on-config_slub_debug.patch
This patch was dropped because it was merged into mainline or a subsystem tree
------------------------------------------------------
From: "Jason A. Donenfeld" <Jason(a)zx2c4.com>
Subject: kasan: depend on CONFIG_SLUB_DEBUG
KASAN depends on having access to some of the accounting that SLUB_DEBUG
does; without it, there are immediate crashes [1]. So, the natural thing
to do is to make KASAN select SLUB_DEBUG.
[1] http://lkml.kernel.org/r/CAHmME9rtoPwxUSnktxzKso14iuVCWT7BE_-_8PAC=pGw1iJnQ…
Link: http://lkml.kernel.org/r/20180622154623.25388-1-Jason@zx2c4.com
Fixes: f9e13c0a5a33 ("slab, slub: skip unnecessary kasan_cache_shutdown()")
Signed-off-by: Jason A. Donenfeld <Jason(a)zx2c4.com>
Acked-by: Michal Hocko <mhocko(a)suse.com>
Reviewed-by: Shakeel Butt <shakeelb(a)google.com>
Acked-by: Christoph Lameter <cl(a)linux.com>
Cc: Shakeel Butt <shakeelb(a)google.com>
Cc: David Rientjes <rientjes(a)google.com>
Cc: Pekka Enberg <penberg(a)kernel.org>
Cc: Joonsoo Kim <iamjoonsoo.kim(a)lge.com>
Cc: Andrey Ryabinin <aryabinin(a)virtuozzo.com>
Cc: <stable(a)vger.kernel.org>
Signed-off-by: Andrew Morton <akpm(a)linux-foundation.org>
---
diff -puN lib/Kconfig.kasan~kasan-depend-on-config_slub_debug lib/Kconfig.kasan
--- a/lib/Kconfig.kasan~kasan-depend-on-config_slub_debug
+++ a/lib/Kconfig.kasan
@@ -6,6 +6,7 @@ if HAVE_ARCH_KASAN
config KASAN
bool "KASan: runtime memory debugger"
depends on SLUB || (SLAB && !DEBUG_SLAB)
+ select SLUB_DEBUG if SLUB
select CONSTRUCTORS
select STACKDEPOT
help
_
Patches currently in -mm which might be from Jason(a)zx2c4.com are
The patch titled
Subject: x86/e820: put !E820_TYPE_RAM regions into memblock.reserved
has been removed from the -mm tree. Its filename was
x86-e820-put-e820_type_ram-regions-into-memblockreserved.patch
This patch was dropped because it was merged into mainline or a subsystem tree
------------------------------------------------------
From: Naoya Horiguchi <n-horiguchi(a)ah.jp.nec.com>
Subject: x86/e820: put !E820_TYPE_RAM regions into memblock.reserved
There is a kernel panic that is triggered when reading /proc/kpageflags on
the kernel booted with kernel parameter 'memmap=nn[KMG]!ss[KMG]':
BUG: unable to handle kernel paging request at fffffffffffffffe
PGD 9b20e067 P4D 9b20e067 PUD 9b210067 PMD 0
Oops: 0000 [#1] SMP PTI
CPU: 2 PID: 1728 Comm: page-types Not tainted 4.17.0-rc6-mm1-v4.17-rc6-180605-0816-00236-g2dfb086ef02c+ #160
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-2.fc28 04/01/2014
RIP: 0010:stable_page_flags+0x27/0x3c0
Code: 00 00 00 0f 1f 44 00 00 48 85 ff 0f 84 a0 03 00 00 41 54 55 49 89 fc 53 48 8b 57 08 48 8b 2f 48 8d 42 ff 83 e2 01 48 0f 44 c7 <48> 8b 00 f6 c4 01 0f 84 10 03 00 00 31 db 49 8b 54 24 08 4c 89 e7
RSP: 0018:ffffbbd44111fde0 EFLAGS: 00010202
RAX: fffffffffffffffe RBX: 00007fffffffeff9 RCX: 0000000000000000
RDX: 0000000000000001 RSI: 0000000000000202 RDI: ffffed1182fff5c0
RBP: ffffffffffffffff R08: 0000000000000001 R09: 0000000000000001
R10: ffffbbd44111fed8 R11: 0000000000000000 R12: ffffed1182fff5c0
R13: 00000000000bffd7 R14: 0000000002fff5c0 R15: ffffbbd44111ff10
FS: 00007efc4335a500(0000) GS:ffff93a5bfc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: fffffffffffffffe CR3: 00000000b2a58000 CR4: 00000000001406e0
Call Trace:
kpageflags_read+0xc7/0x120
proc_reg_read+0x3c/0x60
__vfs_read+0x36/0x170
vfs_read+0x89/0x130
ksys_pread64+0x71/0x90
do_syscall_64+0x5b/0x160
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7efc42e75e23
Code: 09 00 ba 9f 01 00 00 e8 ab 81 f4 ff 66 2e 0f 1f 84 00 00 00 00 00 90 83 3d 29 0a 2d 00 00 75 13 49 89 ca b8 11 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 34 c3 48 83 ec 08 e8 db d3 01 00 48 89 04 24
According to kernel bisection, this problem became visible due to commit
f7f99100d8d9 ("mm: stop zeroing memory during allocation in vmemmap")
which changes how struct pages are initialized.
Memblock layout affects the pfn ranges covered by node/zone. Consider
that we have a VM with 2 NUMA nodes and each node has 4GB memory, and the
default (no memmap= given) memblock layout is like below:
MEMBLOCK configuration:
memory size = 0x00000001fff75c00 reserved size = 0x000000000300c000
memory.cnt = 0x4
memory[0x0] [0x0000000000001000-0x000000000009efff], 0x000000000009e000 bytes on node 0 flags: 0x0
memory[0x1] [0x0000000000100000-0x00000000bffd6fff], 0x00000000bfed7000 bytes on node 0 flags: 0x0
memory[0x2] [0x0000000100000000-0x000000013fffffff], 0x0000000040000000 bytes on node 0 flags: 0x0
memory[0x3] [0x0000000140000000-0x000000023fffffff], 0x0000000100000000 bytes on node 1 flags: 0x0
...
If you give memmap=1G!4G (so it just covers memory[0x2]),
the range [0x100000000-0x13fffffff] is gone:
MEMBLOCK configuration:
memory size = 0x00000001bff75c00 reserved size = 0x000000000300c000
memory.cnt = 0x3
memory[0x0] [0x0000000000001000-0x000000000009efff], 0x000000000009e000 bytes on node 0 flags: 0x0
memory[0x1] [0x0000000000100000-0x00000000bffd6fff], 0x00000000bfed7000 bytes on node 0 flags: 0x0
memory[0x2] [0x0000000140000000-0x000000023fffffff], 0x0000000100000000 bytes on node 1 flags: 0x0
...
This causes shrinking node 0's pfn range because it is calculated by the
address range of memblock.memory. So some of struct pages in the gap
range are left uninitialized.
We have a function zero_resv_unavail() which does zeroing the struct pages
within the reserved unavailable range (i.e. memblock.memory &&
!memblock.reserved). This patch utilizes it to cover all unavailable
ranges by putting them into memblock.reserved.
Link: http://lkml.kernel.org/r/20180615072947.GB23273@hori1.linux.bs1.fc.nec.co.jp
Fixes: f7f99100d8d9 ("mm: stop zeroing memory during allocation in vmemmap")
Signed-off-by: Naoya Horiguchi <n-horiguchi(a)ah.jp.nec.com>
Tested-by: Oscar Salvador <osalvador(a)suse.de>
Tested-by: "Herton R. Krzesinski" <herton(a)redhat.com>
Acked-by: Michal Hocko <mhocko(a)suse.com>
Reviewed-by: Pavel Tatashin <pasha.tatashin(a)oracle.com>
Cc: Steven Sistare <steven.sistare(a)oracle.com>
Cc: Daniel Jordan <daniel.m.jordan(a)oracle.com>
Cc: Matthew Wilcox <willy(a)infradead.org>
Cc: <stable(a)vger.kernel.org>
Signed-off-by: Andrew Morton <akpm(a)linux-foundation.org>
---
diff -puN arch/x86/kernel/e820.c~x86-e820-put-e820_type_ram-regions-into-memblockreserved arch/x86/kernel/e820.c
--- a/arch/x86/kernel/e820.c~x86-e820-put-e820_type_ram-regions-into-memblockreserved
+++ a/arch/x86/kernel/e820.c
@@ -1248,6 +1248,7 @@ void __init e820__memblock_setup(void)
{
int i;
u64 end;
+ u64 addr = 0;
/*
* The bootstrap memblock region count maximum is 128 entries
@@ -1264,13 +1265,21 @@ void __init e820__memblock_setup(void)
struct e820_entry *entry = &e820_table->entries[i];
end = entry->addr + entry->size;
+ if (addr < entry->addr)
+ memblock_reserve(addr, entry->addr - addr);
+ addr = end;
if (end != (resource_size_t)end)
continue;
+ /*
+ * all !E820_TYPE_RAM ranges (including gap ranges) are put
+ * into memblock.reserved to make sure that struct pages in
+ * such regions are not left uninitialized after bootup.
+ */
if (entry->type != E820_TYPE_RAM && entry->type != E820_TYPE_RESERVED_KERN)
- continue;
-
- memblock_add(entry->addr, entry->size);
+ memblock_reserve(entry->addr, entry->size);
+ else
+ memblock_add(entry->addr, entry->size);
}
/* Throw away partial pages: */
_
Patches currently in -mm which might be from n-horiguchi(a)ah.jp.nec.com are